Band-it J93099 Cutter Blade Kit Installation Instructions
Band-it J93099 Cutter Blade Kit is designed for precise and efficient cutting of metal bands used in various industrial applications. With its durable construction and easy installation, this kit offers a reliable solution for cutting and tensioning metal bands. The kit includes a dimensionally matched cutter blade and backing plate, ensuring accurate and consistent cuts. The included bolts allow for proper tensioning of the metal band, resulting in secure and reliable connections.
advertisement
Installation
Instructions
J93099
Cutter Blade Kit
J93099 Kit Installation Instructions for Cutter blade and Backing Plate
Components of this kit are a dimensionally matched set. You may have parts that look similar, but they are different dimensionally if received before May 1 st
, 2004. Parts received before May 1 st
, 2004 should be discarded.
1. Remove old cutter blade screws, cutter blade and backing plate and discard.
2. See illustrations to determine the correct positions for component assembly.
3. Hold cutter blade and backing plate together, insert screws and tighten to 8-14 ft-lbs.
4. Choose the correct length bolts supplied in this kit for your tool. Fully tensioned bolts should flush or extend beyond the cutter blade ¼” max.
Operating Tip: Keep the bolts tight (8-14 ft-lbs.). A loose bolt may cause cracking or premature wear of the cutter blade and/or backing plate. This could result in improper clamp tensioning, locking, and cutting.
Operating Tip: Keep the leading edges of the cutter blade and backing plate free of metal shavings. Metal shavings will result in clamp band gouging during tensioning. Clean and hone the leading edges by hand. Do not use power tools.
Honing should polish surfaces, not remove material.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 1 of 2
Document # P15488 Rev. D
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
Installation
Instructions
J93099
Cutter Blade Kit
J93099 Kit Installation Instructions for Cutter blade and Backing Plate
Components of this kit are a dimensionally matched set. You may have parts that look similar, but they are different dimensionally if received before May 1 st
, 2004. Parts received before May 1 st
, 2004 should be discarded.
1. Remove old cutter blade screws, cutter blade and backing plate and discard.
2. See illustrations to determine the correct positions for component assembly.
3. Hold cutter blade and backing plate together, insert screws and tighten to 8-14 ft-lbs.
4. Choose the correct length bolts supplied in this kit for your tool. Fully tensioned bolts should flush or extend beyond the cutter blade ¼” max.
Operating Tip: Keep the bolts tight (8-14 ft-lbs.). A loose bolt may cause cracking or premature wear of the cutter blade and/or backing plate. This could result in improper clamp tensioning, locking, and cutting.
Operating Tip: Keep the leading edges of the cutter blade and backing plate free of metal shavings. Metal shavings will result in clamp band gouging during tensioning. Clean and hone the leading edges by hand. Do not use power tools.
Honing should polish surfaces, not remove material.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 1 of 2
Document # P15488 Rev. D
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
Installation
Instructions
Hand Tools
½” long
J93099
Cutter Blade Kit
Air Tools
1-3/4” long – S750, S100
2” long – S350
CAUTION: To prevent breakage, backing plate must be installed flush with cutter blade.
CORRECT
Backing Plate
INCORRECT
Leading
Edge
Backing
Plate
Cutter
Blade
Hone these surfaces
Rough edges on clamp band are indication of need to hone cutter blade.
Cutter Blade
Installation
Instructions
Hand Tools
½” long
J93099
Cutter Blade Kit
Air Tools
1-3/4” long – S750, S100
2” long – S350
CAUTION: To prevent breakage, backing plate must be installed flush with cutter blade.
CORRECT
Backing Plate
INCORRECT
Leading
Edge
Backing
Plate
Cutter
Blade
Hone these surfaces
Rough edges on clamp band are indication of need to hone cutter blade.
Cutter Blade
advertisement
Related manuals
advertisement