user manual
Troubleshooting
Review the following pages before calling for service.
Problem Possible Cause What to do
Timer knob |e [Is the power cord inserted firmly? e Insert the power cord firmly.
does not tum
Drum does |e Is the door closed? e Close the door.
not turn e Is the power cord inserted? e Insert the power cord firmly.
e Does the receptacle have power? e Check the power cord receptacle.
Hot alr is not |* Does the receptacle have power? ® Set the timer to hot air.
blowing out
The laundry ¡e Are the front and back filters clogged? e Clean the filter.
Is not e |s there too much laundry in the dryer? e Reduce the amount of clothes in
meruahy the dryer.
rie
e Have items been added whilst the dryer | © Re-dry the items again.
is in operation?
® Has the laundry become twisted whilst drying? | ® Uniwist the items and re-dry.
e Has the dryer been placed in a small e Place the dryer in a well-vented area.
and badly ventilated area?
e Have you set the dryer to Anti-Wrinkle? e Try using 'Warm' or 'Hot' setting instead.
Dryer does e Is there a power failure? e Try again when there is power.
not start e Is the power cord inserted firmiy? e Insert the power cord firmly.
e |s the door closed? eo Close the door.
e |s the timer in the OFF position? e Set the dry time.
Dryer Technical Specifications
Model BD45KG
Drying Capacity 4.5kg
Voltage 220-240V~ 50Hz
Rated Input 1450 W
Net Weight 20kg
Dimensions 600x435x700mm
Outlet Size p80MM
NOTE: Consistent with our continuing product development
policy, improvements may have been made which render
the contents of this package slightly different to that shown.
12
Baumatic
4.5KG REVERSIBLE WALL MOUNTED DRYER
A,
A
MODEL: BD45KG
20 Oo [7—7
Instruction Manual
Important Safeguards
When using electrical appliances, in order to
reduce the risk of fire, electric shock, and/or
injury to persons, basic safety precautions
should always be followed, including:
For Your Safety
Read all instructions carefully, even if you are
quite familiar with the appliance.
e This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
e Young children should be supervised to ensure
that they do not play with the appliance.
* INDOOR USE ONLY: this appliance is not intended
for outdoor use.
® Do not place naked flame sources, such as
candles, on the appliance.
e Do not locate the appliance or cord near heat
sources such as radiators, heaters, air ducts or
direct sunlight.
e Do not block any of the ventilation openings.
Ensure that vents are not covered by newspapers,
tablecloths, curtains etc.
e Do not run the cord under floor coverings.
Instead, arrange the cord away from traffic areas
where it will not become a trip hazard.
e Jo disconnect the appliance, turn the appliance
off, switch off the power outlet and remove the
plug from the power outlet.
e Do not misuse the cord. Never carry the appliance
by the cord or pull to disconnect it from the outlet.
Instead, grasp the plug and pull fo disconnect.
e Do not operate the appliance if it has a damaged
cord or plug, after the appliance malfunctions,
or has been dropped or damaged in any way.
Consult the manufacturer.
e Do not attempt to repair, disassemble or modify
this appliance. The warranty becomes void if not
serviced or repaired by a qualified person.
e Do not place items that have been soiled with
flammable liquids inside the dryer without washing
them with detergent thoroughly beforehand.
e Do not excessively bend, stretch, twist or bind the
power cord or place heavy objects on it.
e Do not use an extension cord with this appliance.
e This appliance is only to be serviced by a qualified
person. There are no user-serviceable parts inside.
e Do not install in a tight-fitting cabinet.
e Do not overload the fumble dryer.
e Ensure foreign objects do not find their way into
the tub of the tumble dryer.
e The door window may be hot after a long drying
cycle. Please ensure children are kept away from
the machine.
e If the tumble dryer is not wall mounted, place in
a flat, firm, dry and well-ventilated place. Use the
adjustable front legs to assist in levelling the dryer
if need be. Do not place it on any soft material
such as foam or plastic.
e Do not use flammable or combustible materials
such as gas, petrol, alcohol or lacquer in the
tumble dryer.
e After turning off the power supply to the tumble
dryer, wait at least 2 minutes before turning it
back on again.
e Please remove the transport packaging at the
rear of the tumble dryer, prior fo use.
e |f the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
CAUTION: If this appliance is supplied from a
cord extension set or an electrical portable outlet
device, the cord extension set or electrical
portable outlet device must be positioned so that
it is not subject to splashing or ingress of moisture.
Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as
in a tumble dryer. The items become warm,
causing an oxidation reaction in the oil. Oxidation
creates heat. If the heat cannot escape, the items
can become hot enough to catch fire. Piling,
stacking or storing oil-affected items can prevent
heat from escaping and so create a fire hazard.
Save these Instructions
Maintenance
Cleaning the Lint Filter
Please unplug the power cord prior to any cleaning.
The lint fitter must be in place whenever drying. It must
be cleaned before each use.
1. Removing the filters
Remove by pulling outwards with fingers, inserted
into the four holes around the exhaust vent shroud.
The filter is in 3 parts: Exhaust vent shroud, lint filter
and exhaust filter (ds shown in figure1)
The filter fixed in the
bottom of the drum
Ca
4
| É
/А р
EN Ш
AN A
NA A
а |
j |
Exhaust Lint Exhaust
Vent shroud filter filter Figure 1
2. Cleaning the filter
Separate "exhaust vent shroud", "lint filter" and
"exhaust filter". Clean the lint on the lint filter and
exhaust filter with a soft brush or vacuum cleaner.
Do not damage the filters (as shown in figure 2).
EN a
>
Al LEN IC
A CT 9
Y I .
x
PT NX 2 Figure 2
Lint filter Lint Exhaust filter
3. Re-installing the filter
After cleaning, assemble in the sequence of
"exhaust fitter - lint filter - exhaust vent shroud",
align the recesses in the centre with the
projection in the centre of the drum. Make sure
that it is firmly inserted (as shown in figure 3).
Dust Cleaner
>
Figure 3
Note: The filter fixed in the bottom of the drum
should also be cleaned with a soft brush.
Cleaning of the Air Intake Filter
The filter should be cleaned once a month.
Remove by pulling outwards, holding the upper and
lower ends of the air intake shroud. Remove the filter
inside the shroud and clean it with a soft brush.
Reassemble and install as before.
Da
SN J
SS
Air Intake Shroud Air Intake Filter
Slightly push upwards with your thumb until the latch
hook disconnects, then remove.
Cleaning the interior & exterior of the Dryer
Do not wash directly with water.
Do not use thinner, gasolene or alcohol.
Remove any residue before drying the next load.
Do not use any type of spray cleaner when cleaning
the interior. If dryer drum becomes stained, clean
the drum with a damp cloth.
Clean cabinet with mild soap and water. Do not use harsh
or abrasive cleaners, as this could damage the dryer.
Do not dry unwashed items in the tumble dryer.
[tems that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers should
be washed in hot water with an extra amount of
detergent before being dried in the tumble dryer.
Items such as foam rubber (latex foam), shower
caps, rubber backed articles and clothes or pillows
fitted with foam rubber pads should not be dried in
the tumble dryer.
Fabric softeners, or similar products, should be used
as specified by the fabric softener instructions.
The final part of the tumble dryer cycle occurs
without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the
items will not be damaged.
WARNING: Never stop a tumble dryer before the
end of the drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated. This appliance is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
WARNING: Regularly
clean the lint trap
CAUTION! HOT SURFACE
® Do not touch the intake during the
drying cycle due to high temperatures
LL READ THE INSTRUCTIONS
Upside down Installation
For convenience, this dryer can be installed upside down. The installation steps are below:
1) Take off the rubber plugs on the
top of the unit (as per Fig.6). Then
Fig.6 Fig.7
¥
take off the four legs from the
bottom (as per Fig. 7).
2) Put the dryer upside down and
install the four legs at the bottom
(Top side of the original dryer, as
per Fig.8). Push rubber plugs inside
holes on the top of the dryer
(Bottom of the original dryer, as
per Fig.9).
3) There is a printed control panel
in the accessories bag. Rip the
protective paper and stick it over
the existing panel, as per Fig. 10.
Upside down Wall Mounting Installation
The Upside down dryer can also be wall mounted. You can follow “Installation Instructions” and “Wall
Mounting Instructions” on the Page 8 and Page 9 to install the tumble dryer.
If it is unavoidable that fabrics that contain vegetable or cooking oil, or have been contaminated
by hair care products, be placed in a tumble dryer, they should first be washed in hot water
with extra detergent. This will reduce, but not eliminate, the hazard.
Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of
detergent before being dried in the tumble dryer.
Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
The final part of a fumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are
left at a temperature that ensures that the items will not be damaged.
WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly
removed and spread out so that heat is dissipated.
Description of the appliance
~~
AT Door Gasket
Door °
Drum
Ema |
O
Air intake shroud
Heat selector knob
Window Timer selector knob
0
. — Start button
e Exhaust vent
A) o
| Back cover
Casing °
Operating your dryer
Electrical Requirements
The unit is required to be plugged into a three pin
socket that is reliably grounded.
Plug the power cord into the socket.
0 “im.
Loading the dryer
It is recommended that items are placed into the
dryer one at a time. This ensures they are not
tangled which results in uneven drying. When closing
the dryer door prior fo starting the unit, ensure that
items are not jammed in the door.
Tips before drying
Prior to loading the dryer, check that the items do
not have the following symbols anywhere on them.
If they do, do not tumble dry these items.
|- | /
Dry flat Dry in the shade
Do not tumble dry Hang to dry Drip dry
e Check the items to be dried do not have
combustible materials or foreign objects within
them i.e.: lighters, hair pins, coins.
A
+
e Turn items with zippers inside out and fasten
buckles.
(№
® Dryer heat may permanently set stains, ensure
you check prior to drying that stains are removed.
Separate dark and light coloured items as you
would do when washing.
For best results load the dryer with similar fabrics.
Place small delicate items in a mesh bag, and
do not overload the dryer.
e The maximum mass is 4.5 kilograms of dry textile
material for the dryer. Do not overload. The
tumble dryer is intended only for drying textile
material washed in water.
Drying time reference
fable
3. To install the hanging hook to timber, start af Fig 2.
4. Align hanging hooks and fasten screws tightly.
5. Install exhaust connector: for upwards discharge,
join sections 1 and 3, for downwards discharge,
join sections 1, 2, 2, & 3 as per Fig 3.
The maximum length of the venting hose (not
supplied) that you connect to the exhaust
connector must be 1.5 metres. The diameter of
venting hose should be 80mm.
6. Using 3 x 16 mm screws (provided) to fix the outlet
in place firmly.
7. Using 4 x 12mm screws (provided) to fix the 2
spacers as per Fig 4.
8. With assistance, mount dryer on wall bracket as
per Fig 5.
2 |
Fig.2 Smm long screws
Drying Dry time
Capacity Regular Airing
Approx. 1kg Approx.30min | Approx.55min
Approx.2kg Approx.60min | Approx.110min
Approx.3kg Approx.120min
Approx.4.5kg Approx.200min
Drying times can be affected by many factors, such
as material, bulkiness, how full the dryer is etc. The
above list is only a guide.
Spacers
>, 2mm long screws
Fig.5
Installation Instructions
Where to place your dryer
Place the dryer in a dry, well-ventilated area. It should
be positioned away from heat and direct sunlight.
If the dryer is not wall mounted, it must be placed
on firm horizontal ground. Do not place the dryer on
carpet as this will block the intake. There should be
at least 10cm between the dryer and the wall.
The dryer comes with fixed legs that need to be
assembled to ensure stability.
Leg
7
LA
7
7
=
If the dryer is rack mounted, a secure bracket is
required to ensure stability and prevent vibration.
At least 10cm between the dryer and walls is
required (The bracket is not included).
100
10cm
N
Bracket
Wall Mounting Instructions
1. Determine dryer position on wall and mark required
bracket position. This dryer is not suitable to be
directly placed on top of a washing machine.
* A minimum 50mm is needed between the top of
the dryer and the ceiling for ease of installation.
* If mounting above a washing machine, allow
sufficient room to open the lid of the washing machine.
Tools Required
Tools & parts | Drill & 3mm Bit 1
required Philips Head screw Driver 1
for plaster/
wooden wall | Wood Screws, ¢12x50mm 4
Timber screws
Helper to lift dryer onto wall 1
Wall Mounting Kit Includes
Ss
Hanging brackets 1
Plastic spacers
Exhaust connector
Description
12mm Long Screws
25mm Long Screws
16mm Long Screws 7 3
2. Fix the wall hanging brackets (1 supplied) to the
wall securely (e.g. info the stud.) Fit a timber slat
between the studs to mount the brackets if the
stud position is too wide.
Stud
WVWOFS
Ensure brackets are
securely fastened. Fit
Timber slats if necessary
Control Panel Functions
Heat Selector button
Select 'High Dry' for items that are particularly bulky or large quantities.
Select 'Low Dry for delicate items such as silk, nylon, linen etc.
Drying Program Selector
Ш. Low
J High
Heat Selector Knob
There are five drying combinations available: Cool, Anti-wrinkle, Warm, Hot and Air dry.
( N ( >
Air Dry: This function runs Off: When the 'Drying Timer'
with cool air, primarily to air dial is in the 'Off' position no
items that require power is supplied to the unit.
freshening. i.e.. clothes that As soon as the dial is tumed
have been stored for a long clockwise to the desired
period of time. program, the dryer will start.
N
ol
80 OFF/O 20
Air Dry * 40
60 \, 60
40
\ 80
( 20 | Warm
Off: When the 'Drying Timer / 100
dial is in the 'Off position no | OFF/0 f 20
i i i o
power is supplied to the unit. 20 S~e— e— “140
As soon as the dial is turned
clockwise to the desired Hot
program, the dryer will start.
N
Drying time (min)
Hot: For drying large quantities or bulky
items (Dryer drum is more than 1/2 full).
Select the 'High' heat option and set
the timer for more than 120 minutes.
Start button
~
Cool: This function is generally used
to cool the items that have just
been dried. This helps to prevent
creasing. Instead of the motor
pushing heat into the drum of the
dryer it will generate cool air.
Warm:
Anti-wrinkle function: This is used
for items that are difficult to iron
i.e.: cotton shirts and linen. Using
the heat selector knob, choose
'Low'. Set the drying timer knob
between 30-60 minutes depending
on the amount of items in the dryer.
Once the timer stops (including the
Cool program) the items will still
contain moisture, making the
ironing process easier.
Warm drying function:
This function will dry and cool
items and in most cases leave
items wrinkle free (depending on
material). Select the 'High' heat
option. Set the timer between
-12 inutes.
| 60 O minutes D
After having set up the Heat Selector and Timer Dial, press the Start button. the dryer
will start and work until the program is finished. If the during this process the door is
opened or power is switched off, the dryer will stop working. In order to start the dryer
again after the door is closed or power is switched back on, you will need to push the
Start button, then the dryer will start working again.
Start button
NOTE: This Start button is only designed to start the dryer working. If you press this
button during the drying process, the dryer will not pause. In order to stop the
dryer, you must turn the timer dial to the Off position.
5
Operation Precautions
Delicate items should be placed into a nylon net
bag prior to drying. It is not recommended fo dry
under wire bras in this unit.
| XY a »
À > М
< М
EZLN
Ensure that foreign objects do not find their way into
the dryer. All pockets should be emptied, and
buttons, buckles and zips fastened. This will also help
reduce impact noise when the items hit against the
turning drum.
SR
Do not add items into the dryer whilst it is in
operation.
If drying large items such as a blanket, it is
recommended that from time to time you open the
dryer door, shake the item, place the item back in
the dryer and close the door. This will ensure even
drying.
Flip over clothes
Electrical Requirements: A three pin socket must be
used (reliably grounded).
0 “Yi
To ensure you get the most out of the Anti-wrinkle
function, do not overload the dryer. Remove the
dried items from the dryer immediately and hang
on coat hangers. Iron the items if desired.
Reduced load
To minimize the risk of fire in a tumble dryer, the
following should be observed:
e [tems that have been spotted or soaked with
vegetable or cooking oil constitute a fire hazard
and should not be placed in a tumble dryer.
Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as in
a tumble dryer. The items become warm, causing
an oxidation reaction in the oil. Oxidation creates
heat. If the heat cannot escape, the items can
become hot enough to catch fire. Piling, stacking or
storing oil-affected items can prevent heat from
escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil, or have been contaminated by hair care
products, be placed in a fumble dryer they should first be washed in hot water with extra detergent. This will
reduce, but not eliminate, the hazard.
The 'cool down' cycle of tumble dryers should be used to reduce the temperature of the items. They should
not be removed from the tumble dryer or piled or slacked while hot.
Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline,
dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include acetone, denatured
alcohol, petrol/gasoline, kerosene, spot removers(some brands), turpentine, waxes and wax removers,
e [tems containing foam rubber (also known as latex foam) or similarly textured rubber-like materials should
not be dried in a fumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
e Fabric softeners or similar products should not be used in a tumble dryer, to eliminate the effects of static
electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or
product,
e Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during drying. When available, a
drying rack could be used for such items.
e Plastic articles such as shower caps or babies' waterproof napkin covers should not be placed in a fumble
dryer.
e Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber-coated tennis
shoes should not be placed in a tumble dryer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising