babyscale manual - My weigh scales

babyscale manual - My weigh scales
babyscale manual - My weigh scales
Home
Pocket and Mini Scales
Medium Scales
Large Scales
Online Stores
Support
Contact Us
MBS-2010 Baby Scale Manual
FAQ
General Tech Support
My Weigh Electronic Baby Scale guide
in alphabetical order:
200Z / 300-Z Manual
1scale Manual and
Calibration guide
3001P & 7001DX Series
Manual
OLD 3001/6001 Series
Manual (Archives)
AXE Manual
BodyFlight Manual
C200 Convertible Manual
Durascale Manual
Flipscale Classic Manual
Flipscale Classic
Advanced Programming
Flipscale Interactive
Manual
Flipscale F2 Manual
GemPro manual and
advanced guide
HD-150/300 Manual
iScale Manual
i250 Manual
i500, i1200 & i2600
Manuals
i5000 & i2500 Manual
iBalance 201 Manual
iBalance 101 Manual
Low Batteries & Faulty AC Adaptors are the #1 cause of scale malfunction and inaccuracy!
We test all of our scale returns from consumers. Fully 60% of consumer returns are simply dead
or low batteries. This sounds silly but it's true! A scale will perform slowly, or read inaccurately
when it has low batteries. Please replace the batteries often (and only use good quality
batteries). We include good quality batteries with all of our scales but batteries can run low in
storage. A Faulty AC adaptor can cause your scale to act unstable with numbers "jumping" all
around. Please test your scale with a good set of batteries (instead of the AC adaptor) to
determine if perhaps the AC adaptor is faulty.
1. Install 9V Alkaline Battery into battery compartment or connect with an AC Adapter
To install the battery, remove the battery cover on the underside of the scale. Install a 9volt
battery and push the connector firmly onto the battery terminals. Reinstall the cover. To use the
optional AC adapter, Plug the AC adapter into the jack on the right side of the scale.
The scale has an Auto-off feature that will turn the scale OFF after a few minutes of inactivity to
conserve power.
2. The Process of Weighing
A. Install the tray onto the scale with its 2 screws (if you need the tray).
B. Press the "ON/ OFF/TARE" button.
C. The display will momentarily show "8888".
D. Wait until the display shows "0.00".
E. The scale is now ready for weighing.
F. Put the baby on the scale.
http://myweigh.com/support_manual_mbs2010.html (1 of 3)7/30/2006 8:13:52 PM
babyscale manual - My weigh scales
KD-600 Manual
LS-30 Manual
MBS-2010 Babyscale
Manual & Calibration
MX-50 Manual
MX-300 & MX-120 Manual
OMNI Manual
Palmscale (all) Manual
and Calibration Guide
Palmscale 1.0 and 2.0
Advanced Guide and
Repair
Palmscale 3.0 and 4.0
Advanced Guide and
Repair
Palmscale 5.0 Advanced
Programming and Repair
Guide
Phoenix Talking Scale
Manual
Phoenix Body Fat Scale
Manual
Phoenix Body Fat Scale
Common Questions
G.
H.
I.
J.
Wait till the display stabilizes.
The display shows the baby's weight.
Press "ON/OFF/TARE" button and hold for 2 seconds to switch the scale off.
If weighing has been completed and the weight on the scale has not changed for 30
seconds, the scale will automatically switch off , to save battery life.
3. To Convert Weight Units (Kilograms or Pounds/Ounces or Stones/Pounds)
Some models read Stones/Pounds. This is a UK Standard whereas 1 Stone = 14lb. Press the
KG/LB button to convert between LB/OZ and KG units. This can be done at any time during
weighing. IMPORTANT: The scale will default to the last weight unit used. *The display will
notate "KG" or "LB" to tell you which mode the scale is in (USA version only).
4. Use of the HOLD button
A. Due to the baby's constant movement on the tray, the displayed weight may be hard to
read. It may constantly change. This is when the HOLD function is used.
B. Press "HOLD" button
C. The display shows "hold" and calculates the average from the various weight readings.
D. The value on the display will be fixed, and in the upper left corner a mark ' " ' will flash.
E. Press "HOLD" again and the display will show the updated weight.
F. Press "ON/OFF/TARE" to turn off the scale.
5. Technical details
Max capacity: 20Kg/44lb - Graduation: 10g/0.5oz
It is important to avoid overloading the scale (don't exceed the capacity)
6. Assembly of Baby Tray
When weighing a baby, assemble the baby tray according to the illustration above. Be certain to
fasten the screws tightly and securely. The Tray must be screwed down tight and securely or
injury can occur!
7. Weighing at older Ages
If the child can stand safely, You can remove the baby tray to allow the child to stand on the
scale. Keep the screws for future use. Turn the scale on and wait until the display shows 0.00.
Then the child can step on the scale's platform for weighing.
CALIBRATION:
Pointscale Manual
Proscale Manual &
troubleshooting
**Please note there is an advanced calibration guide for the MBS located HERE**
Tempest manual
Touchscale Manual
Touchscale Advanced
Programming
Triton Manual
Triple Beam Manual &
Troubleshooting
UltraShip Manual
UltraBaby Manual
XL440 Manual
http://myweigh.com/support_manual_mbs2010.html (2 of 3)7/30/2006 8:13:52 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising