KW-316 - Konwa Industrial Sewing Machine

KW-316 - Konwa Industrial Sewing Machine
®
KONWA
KW-316
GRAVITY FEED STEAM IRON
C/W TELFON SHOE
INSTRUCTION MANUAL
&
PARTS LIST
INSTRUCTIONS
1. Hang water bottle one meter above
ironing surface (Refer Bottle Hanging
Instruction).
2. Connect one end of the hose (black
colour) to the iron and the other end to
the bottle.
3. Fill in bottle with tap water only.
4. Tie the electrical cord and hose
together.
5. Plug in the iron cord into a grounded
electrical outlet.
6. Set the temperature dial at No.4 and
let the iron heat up for ten minutes.
7. Open the bottle valve and allow the
hose to fill with water by pressing the
steam switch. The iron is now ready for
use.
8. When not using, place the iron on
the supplied iron rest.
9. Always unplug the
unattended or not in use.
iron
IMPORTANT
Do not stand iron on its back.
when
EXPLODED VIEW
NO.
1
2
3
4
4-1
4-2
PARTS NO.
19047/19117
138200/138300
139200/139100
19816/19835
118000
11803
11801
DESCRIPTION
SILICONE IRON REST E
BASE ASSY 120V
BASE ASSY 120V
COVER
RUBBER HANDLE SET
HANDLE
HANDLE MTG. BRACKET
NO.
8-6
8-7
8-8
8-9
8-10
8-11
8-12
PARTS NO.
14011
1410
54001
14039
14501/14502
14038
14019
4-3
19838
WASHER
9
151505/151504
4-4
11006
NUT (7/16)
10
18904/18905
5
124401
MAIN SWITCH ASSY (G)
11
19038
5-1
6
12091
19815
ON OFF SWITCH
THERMO SHIELED
12
13
19037
19037
7
118001
HANDLE CAP SET
14
19817
7-1
7-2
171003
11802
STEAM SWITCH
HANDLE CAP 1
15
16
19827
161000
7-3
19837
HANDLE CAP 2
16-1
16009
7-4
8
19839
145100/145230
145110/145210
14005
14001
14004
14007
14101
SWITCH BUTTON
SOL. VALVE ASSY. 120V
SOL. VALVE ASSY. 120V
HOSE BARB NUT
HOSE BARB SOLENOID
VALVE O-RING
RUBBER PACKING
VALVE PIN
16-2
16-3
16-4
17
17-1
17-2
17-3
1610
16010
16107
16108
16018
16031
16003
8-1
8-2
8-3
8-4
8-5
DESCRIPTION
VALVE SPRING
VALVE BODY
VALVE NAME PLATE
COIL COVER
VALVE COIL 120V
COIL WASHER
LOCKING NUT
HT-577 THERMOSTAT
ASSY
LINE CORD 120V
BOLT HANDLE MTG.
BRACKET
MTG. BRACKER WASHER
MTG. BRACKET WASHER
TAP TITE SCREW
(M6X1.0P)
MTG. BRACKET WASHER
WATER BOTTLE ASSY
HANGER WATER
BOTTLE
FILTER
WATER BOTTLE
WATER VALVE
SILICONE HOSE SET
FILTER
SILICONE HOSE
SILICONE HOSE SPRING
Tips for ironing with professional results :Initially, to allow water to enter into the hose and iron, press the steam switch. This may take a few
seconds, then you will see the seam come out.
Begin to iron.
For best results, it is only necessary to press the steam switch for a few seconds at a time. It is not
necessary to activate the steam switch continuously.
There are several settings on your temperature dial. Recommended temperature settings are as
follows :#1, 2 – Preheat
#3
– Silk and delicate fabrics (low temperature)
#4
– Cotton and wool (medium temperature)
#5
– Linen (high temperature)
A telfon shoe is recommended to prevent garment shine and starch built-up.
When unattended or not in use, always turn off and unplug your iron.
TROUBLE SHOOTING GUIDE
PROBLEM
PROBABLE CAUSE
SUGGESTED REMEDY
Iron does not heat.
No power to iron.
Check electric outlet.
Temperature dial is in “OFF” Set temperature dial to No.3, 4
position.
or 5.
Temperature dial is set on No. Set temperature dial to No.3, 4
1 or 2.
or 5.
No steam or very little steam.
Iron spits water.
Little or no water in the bottle.
Fill water with bottle.
Bottle not high enough.
Bottle must be 36” above the
ironing surface.
Clogged filters.
Remove and rinse filter under
water faucet.
Clogged steam holes.
Clear holes with straightened
paper clip.
Iron is not hot enough.
Turn temperature dial up
(clockwise). Let iron heat up.
Steam switch held down too Release steam switch and let
long.
iron heat up.
Iron too hot.
Temperature dial is set too Turn thermostat dial down
high.
(counter clockwise).
Iron not enough hot.
Temperature dial is set too Turn thermostat
low.
(clockwise).
dial
up
CEILING HOOK INSTALLATION INSTRUCTION
IMPORTANT – DO NOT SLIDE ELECTRICAL WIRE OR WATER HOSE OVER HOOK. SLIDE
CHAIN LINK ONLY OVER HOOK.
CAUTION – Injury to persons or damage to the ceiling may result if the bottle or mounting
hardware is pulled from the ceiling. To avoid such injury, mount only to ceiling member that are
structurally sound.
FOR HOLLOW CEILINGS
Drill 5/8” diameter hole in the ceiling at desired hook location.
Assemble toggle bolt by screwing bolt (A) into toggle (B).
Insert flaps and bolt assembly (A / B) hinge up into ceiling
hole with the bolt (A) protruding through ceiling. Lock
assembly by turning hook (C) clockwise until firmly seated.
FOR WOOD BEAM CEILINGS
Screw hook clockwise into ceiling until firmly seated.
FOR EITHER METHOD
Hang the bottle assembly by a chain from the hook so that
the bottom of the bottle is 1 meter (1 yardstick) from the water
inlet on the iron.
KONWA®
KONWA INDUSTRIAL SEWING MACHINE (M) SDN BHD (124740-M)
Head Office: Lot 11 & 13, Jalan 51/201, Off Jalan Tandang, Seksyen 51, 46050 Petaling Jaya,
Selangor Darul Ehsan, Malaysia.
Tel: +603-7788 1111
Fax: +603-7788 5555
E-mail: konwa@konwa.com.my URL: www.konwa.com.my
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising