Sola Power Supply Catalog - Clearwater Technologies Inc.

Sola Power Supply Catalog - Clearwater Technologies Inc.
4
Power Supplies
SolaHD has a broad range of standard power supplies to
suit almost any industrial application. Updated approvals and
user friendly features make power system design easy. The
product line includes one of the broadest ranges of DIN Rail
and linear-based power supplies in the marketplace. The
DIN Rail products feature full CE compliance (including all
the elements of CE design engineers need to worry about:
safety/LVD, EMC, and ingress protection). UL 508 approvals eliminate derating in UL 508 listed panel systems. Global
inputs are available for installations around the world.
Three phase input options are available on many of the SDN
DIN Rail products that convert 380/480 three phase directly
to 24 Vdc. They provide extremely stable, regulated low
voltage without the need for a step down transformer saving
space and money.
SolaHD now offers a DC UPS to provide backup power to
the power supply in the event of a blackout.
Linear vs. Switcher
SolaHD has provided both linear and switching technology
products for many years. As a leading supplier of power
products to the industrial market, both technologies are still
important. Switching technology (most of SolaHD’s DIN Rail
line) is the predominant method of AC-DC conversion for
almost any type of electronic system sold today in the world,
from PLC’s to desktop PC’s.
Linear Power Supplies for a broad range of applications
The small size, lightweight and high efficiency of the
switching products give them significant advantages over
the linear technology products (SolaHD’s SL and 83 series).
SolaHD switching products provide well filtered and
regulated DC of typically less than 1% deviation from the
nominal output voltage.
Linears are about 50% efficient while their switching
counterparts are typically over 80% efficient. Switchers
are light enough to mount on a DIN Rail, while only the
smallest linears are capable of being securely mounted to
a DIN Rail. Linears are still popular today because they do
provide very tight regulation (<.01% typically), almost
perfectly clean DC, fast transient response and their low
component count helps provide a lower material cost for its
user. Linears are typically open frame because of the
excessive heat dissipation from their low efficiency.
SolaHD’s industry standard linears, however, are available
with optional covers for safety. Most linears are recognized
to UL 60950 and cannot meet the stricter temperature
requirements of the UL 508 Listing, such as with SolaHD’s
DIN Rail power supplies.
Linear vs. Switcher
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
DC Power Supply Selection Process
Power supplies can be selected online by visiting our
website. Enter your power requirements and a list of matching power supplies will list. You can also manually select a
power supply by following the directions below:
1) Gather the required information.
• Input voltage and frequency?
• Wattage needed?
• Number of outputs?
• Voltage of each output?
• Amperage of each output?
• Don’t forget to take into account the peak
.loading of each output.
• Battery Backup
2) Calculate the power (wattage) of the DC power
supply you need. If more than one output is required,
.do the following calculation:
• Multiply the Voltage times the amperage of
each output to calculate the wattage of each
output. Next, add together the wattage of
each output to get the total wattage for the
supply.
3) Determine which models from the Power Supply
Selection Chart (on the next page) meet all of the
required specifications.
Selection Worksheet
Output:
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
_______ Vdc x _______ Amps = ________ Watts
Add Watts from each output to calculate
Total Watts = ________
Physical Dimensions:
_______H x _______W x _______D
Mounting:
_______ DIN Rail
_______ Chassis
_______ Other
Other required features or options:
4) Download the specifications sheets from our web
site (www.solaheviduty.com).
5) Check the mounting style, connections and physical
size of the power supply to ensure its suitability for the
intended application.
6) Check for applicable safety approvals for the country
and application the power supply will be used in.
Try our online product selector at
www.solaheviduty.com/psselect.
Enter your power requirements and a list
of matching power supplies will list.
It’s fast and easy.
If you have filled out this form and cannot find the
appropriate power supply, please fax (800-367-4384) or
e-mail (tech@sola-hevi-duty.com) this information to the
Technical Services group.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Power Supply Selection Table
This chart is intended only as a guide for selecting a series of DC power supply, some of the series listed
may not work in all applications.
Input Voltage
Series
DC
115
Vac
230
Vac
SDN™
X
X
X
SDP™
X
X
X
SCP
X
X
X
SCD
Output Voltage
380/480
Vac
3.3 V
5V
X
15 V
X
24 V
X
X
X
SCL
12 V
Number of Outputs
Power Range
48 V (Total Watts) Single Dual Triple >4
X
X
- DIN Rail mount compact
118
X
X
X
15 - 100
X
X
X
X
X
X
30 - 100
X
X
X
X
X
X
X
SFL
X
X
GL
OEM
Switchers
X
X
X
X
X
X
SMP
X
X
X
X
X
X
SHP
X
X
X
X
X
X
Silver Line
Linears
X
X
X
X
X
X
X
X
X
101
60 - 960
X
X
Page
- DIN Rail mount
- DC Battery Back-up Available
- Redundant options
- NEC Class 2/DeviceNetTM
X
X
Notes
X
30
X
X
4 - 10
X
X
X
X
75 - 600
X
40 - 200
X
X
X
X
X
250 - 1000
X
X
X
X
X
1500 - 2000
X
X
X
X
15 - 244
X
X
X
- DIN Rail mount/Chassis
124
- DIN Rail mount/Chassis
- DC input
128
- DIN Rail mount/Chassis
126
- DIN Rail mount
- Adjustable Pot, Red or
UPS option
134
- 40 - 110 Watt, open frame,
Molex type connections
- 200 Watt, enclosed with
connected screw terminals
143
- Modular design
- Screw Terminals (OEM) supply
- Configurable Voltage Output
- Industry standard footprint
- Screw terminals and
optional covers
146
151
137
DIN Rail Selection Guide
Output Voltages
48
SDP 1-48-100T
24
15
12
10
5
SDP 06-24-100T
±15
±12
SCL 4D15-DN
SCL 4D12-DN
SCL 10D15-DN
SCL 10D12-DN
SCP 30D15-DN
SCP 30D12-DN
1
SDP 1-24-100T
SFL 1.5-48-100
2.5
3
A
M
P
S
SDN 2.5-24-100P
SDP 2-24-100T
SFL 3-48-100
3.8
4
SDP 4-24-100RT
5
SDN 5-24-100P
SDN 5-24-100C
SDN 5-24-480 (3Ø)
SFL 6-48-100
5/12/12
SCP 30D524-DN
SCP 30S524B-DN
SCL 10T512-DN
SCP 30T512-DN
SDP 2-12-100T
SDP 5-5-100T
SCP 30S5B-DN
SFL 6-12-100
SDN 10-24-100P
SDN 10-24-100C
SDN 10-24-480 (3Ø)
10
12
SDP 2-12-100T
SCP 30S12B-DN
SDP 3-15-100T
SCP 100S24X-CM
SDN 4-24-100LP
SDP 4-24-100LT
6
SCP 30S15-DN
5/24
SFL 12-48-100
SFL 12-24-100
20
SDN 20-24-100P
SDN 20-24-480C (3Ø)
25
SFL 24-24-100
30
SDN 30-24-480 (3Ø)
40
SDN 40-24-480 (3Ø)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN-C Compact DIN Rail Series
The SDN-C DIN rail power supplies are the next generation
of the popular SDN series. These models combine high
efficiency and compact size with new visual diagnostic
LEDs to offer the most performance available from SolaHD.
Essential industrial features such as Sag Immunity, Power
Factor Correction, and universal voltage input have been
retained in this series. Wide temperature operating range
and parallel operation capability make the new SDN-C units
suitable to a variety of industrial applications.
Features
• Compact packaging to save space on the DIN rail
–27% reduction in width along the rail compared
to existing 10A model
–23% reduction in width along the rail compared to
the existing 5A model
• New visual diagnostic LEDs for input and output status
at a glance
• High MTBF means high reliability and long life
• Higher efficiency saves energy and lowers amount of
heat generated in panel
Related Products
• Accepts Universal voltage 85-264 Vac, 50/60 Hz input
• SDU UPS
• SCP series
Applications
• Power Factor Correction (meets EN61000-3-2)
• Industrial Machine Control
• Class 1, Zone 2 Hazardous Locations rating per
UL60079-15
• Process Control
• Patented DIN rail mounting clip
• User Adjustable output voltage accessible via front face
• Parallel capability standard
• Industrial grade design
–-10oC to 60oC operation without derating
–Rugged metal case and DIN connector
EMC and
Low Volt.
Directive
• SDPTM series
• SFL series
–ATEX approval (pending)
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
• SDN-P series
• PowerBoostTM overload capability to start high
inrush loads
• Single phase models meet SEMI F47 Sag Immunity
standard
UL 508 Listed
IND. CONT. EQ.
E61379
• Conveying Equipment
• Material Handling
• Vending Machines
• Packaging Equipment
• Amusement Park Equipment
• Semiconductor Fabrication Equipment
• User-friendly
–LEDs for status
–Large, rugged, accessible screw terminals
–Easy on/off DIN mounting
• Fully tested and burned-in at factory
• RoHS compliant
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
The SolaHD Difference
Strong, all metal DIN connector
for horizontal or vertical mounting
Rugged metal packaging
Multiple output connections for
ease of wiring multiple devices
Large, IP20-rated, screw
terminals for #10 AWG/4 mm2,
for quick, easy installation
New visual diagnostic LEDs
show input and output status
(see table below)
DC OK Relay
Single or parallel use
selectable by user
Adjustable output voltage
Clearly labeled front panel
No internal fan, no extra cooling
required in any power level
UL508 listing means no
derating in UL 508 systems
Full CE compliance for
safety, emissions and
ingress protection
Automatically adjusts for global
Input voltages. No manual
intervention required.
New narrow width
saves panel space
LED Light Status Conditions
All Is OK
AC Power Loss
Brownout
No DC
High Load
Overload
Hot
Too Hot
Input
Green
-
Yellow
Green
Green
Green
Green
Green
Output
Green
-
Green
-
Yellow
Yellow
Green
-
Alarm
-
-
-
Red
Yellow
Red
Yellow
Yellow
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN-C Specifications
Description
Catalog Number
SDN 5-24-100C
SDN 10-24-100C
Input
Nominal Voltage
115/230 Vac
-AC Range
85 - 264 Vac
-DC Range1
90 - 375 Vdc
-Frequency
43-67 Hz, 400 Hz
Nominal Current2
-Inrush current max.
Efficiency (Losses3)
1.65 - 0.55 A
3.2 - 1.0 A
Typ. < 15 A
Typ.< 30 A
> 90% typ. (12 W)
> 90% typ. (24 W)
Active power factor correction to better than 0.92
Power Factor Correction
Output
24V (22.5-28.5 Vdc Adj.)
Nominal Voltage
< ±2 % overall (combination Line, load, time and temperature related changes)
-Tolerance
Initial Voltage Setting
24.5V ± 1%
-Ripple
< 50 mVpp
4
PARD (Periodic and Random Deviation) = 100 mV peak-peak max
PARD
> 30.5 but < 33 Vdc, auto recovery
Overvoltage Protection
< 35V
Power Back Immunity
Nominal Current
-Peak Current
5
-Short Circuit Current
5 A (120 W)
1.5 x Nominal Current at near zero volts at short circuit condition
PowerBoost™
-Current Limit
Parallel Operation
Holdup Time
Voltage Fall Time
10 A (240 W)
1.5 × Nominal Current for 2 seconds minimum while holding voltage > 20 Vdc
Switch selectable single unit or parallel unit operation. Units will not be damaged by parallel operation (regardless of switch position setting).
>20 ms (Full load, 100 Vac Input @ Tamb=+25°C) to 95% output voltage
<150 mS from 95% to 10% rated voltage @ full load (Tamb=+25°C)
< 0.5%
Line and Load Regulation
General
EMC:
-Emissions
-Immunity
Approvals
Temperature
MTBF Standard6
EN61000-6-2:2001, EN61000-6-3:2001, Class B EN55011, EN55022 Radiated and Conducted including Annex. A, EN61000-3-2
EN61000-6-1:2001, EN61000-6-2:2001, EN61000-4-2 Level 4, EN61000-4-3 Level 3, EN61000-4-6 Level 3, EN61000-4-4 Level 4 input
and level 3 output. EN61000-4-5 ISolation class 4, EN61000-4-11, IEC 61000-4-34 voltage dip immunity standard
UL508 Listed, cULus; UL 60950-1, cURus; IEC60950-1; UL60079-15 (pending) and IEC60079-15 (pending)
CE (LVD 73/23 & 2004/108/EC), (EMC 89/336 & 93/68/EEC); EN61000-3-2
Storage: -25 to + 85oC, Operation -10 to +60oC full power, with linear derating to half power from 60 to 70oC (Convection cooling,
no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation.
> 650,000 hrs
> 550,000 hrs
5 Years
Warranty
General Protection/Safety
Protected against continuous short -circuit, continuous overload, continuous open circuit.
Protection Class 1 (IEC536), degree of protection IP20 (IEC60529) Safe low voltage: SELV (acc. IEC60950-1)
Visual: 3 status LEDs (Input, Output, Alarm)
Relay: N.O. contact rated 200ma/50 Vdc
Status Indicators
Installation
Fusing
-Input
-Output
Mounting
Connections
Case
-Free Space
H x W x D (inches/mm)
Weight (lbs/kg)
Internally fused
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required for
wire/loads if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Simple snap-on to DIN TS35/7.5 or TS35/15 rail system.
Input: Screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors.
Output: Two terminals per output, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors.
Fully enclosed metal housing with fine ventilation grid to keep out small parts.
15 mm in front, 25 mm above and below, 10 mm left and right.
4.88 in. × 1.97 in. × 4.55 in. (124 mm × 50 mm × 116 mm)
4.88 in. × 2.36 in. × 4.55 in. (124 mm × 60 mm × 116 mm)
1.5 lbs (.62 kg)
2.2 lbs (1.1 kg)
1. Not UL listed for DC input.
2. Input current ratings are conservatively specified with low input, worst case
efficiency and power factor.
3. Losses are heat dissipation in watts at full load, nominal input line.
4. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth
scope and 50 Ohm resistor.
5. Peak current is calculated at 24 Volt levels.
6. MTBF 115 Vac (@120 watts & 240 watts) at 40oC ambient per Telecordia Issue 1.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ Series Dimensions
D
W
Catalog
Number
+ +
-
-
OK
24 VDC / 2.5 A
OK
NEC Class 2
Power Supply
24-28 V
Dimensions - inches (mm)
H
W
D
SDN 5-24-100C
4.88 (124)
1.97 (50)
4.55 (116)
SDN 5-24-480
4.88 (124)
2.91 (73)
4.55 (116)
SDN 10-24-100C
4.88 (124)
2.36 (60)
4.55 (116)
Single
Parallel
H
S O LA
Power Supply
SDN 2.5-24-100P
C
U
L
).$ #/.4 %1
(!
US LISTED
115/230 VAC 1.3-0.7 A 50/60 HZ
N
L
W
D
S O LA
H
Power Supply
SDN 20-24-480C
).$ #/.4 %1
(!
Catalog
Number
Overload
Output:
24 VDC / 20 A
Electronically protected
2428V
+ + - -
OK
Single Use
L1 L2 L3
Parallel Use
Input:
3PH 380/500 VAC
1.7/1.5A/Phase 50/60 Hz
Reset fuse mode
US LISTED
Continuous Mode
U
L
Fuse Mode
C
Dimensions - inches (mm)
H
W
D
SDN 10-24-480
4.88 (124)
5.90 (150)
4.55 (116)
SDN 20-24-480C
4.88 (124)
2.56 (65)
4.55 (116)
SDN 30-24-480
4.88 (124)
9.72 (247)
4.55 (116)
SDN 40-24-480
4.88 (124)
11.10 (282)
4.55 (116)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Supplies
4
SDN™ Series Mounting
DIN Rail Mounting
Snap on the DIN Rail:
1.Tilt unit slightly backwards
2.Put it onto the DIN Rail
3. Push downwards until stopped
4. Push at the lower front edge to lock
5. Shake the unit slightly to ensure that the retainer
has locked
Alternative Panel Mount: Using the optional SDN-PMBRK2
accessory, the unit can be screw mounted to a panel.
Detachment from DIN Rail:
Chassis Mounting
Dimensions
Instead of snapping a SolaHD SDN™ unit on the DIN Rail,
you can also attach it using the screw mounting set
SDN-PMBRK2.
This set consists of two metal brackets, which replace the
existing two aluminum profiles.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN-P DIN Rail Series
The SDN DIN Rail power supplies provide industry leading
performance. Sag Immunity, transient suppression and noise
tolerant, the SDN series ensures compatibility in demanding applications. Power factor correction to meet European
directives, hazardous location approvals and optional
redundant accessories allow the SDN series to be used in
a wide variety of applications. Wide operation temperature
range, high tolerance to shock and vibration and reliable
design make the SDN series the preferred choice of
users everywhere.
Features
UL 508 Listed
IND. CONT. EQ.
E61379
• Power Factor Correction (per EN61000-3-2)
• Auto Select 115/230 Vac, 50/60 Hz Input
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
EMC and
Low Volt.
Directive
• Single Phase models meet SEMI F47 Sag Immunity
• Class 1, Zone 2 Hazardous Locations
– ATEX approval on 2.5 through 10A, 24 Vdc
Single Phase Models
– ATEX approval pending on 12 Vdc and 48 Vdc
single phase models
• Improved metal mounting clip
• DC OK Signal
• Adjustable Voltage
• SDN10-24-100P New Compact width (3.26”)
• Parallel Capability standard on all units
• Industrial grade design
– -10°C to 60°C operation without derating.
Indefinite short circuit, overvoltage and
overtemperature protection.
– Powers high inrush loads without shutdown
or foldback
– Rugged metal case and DIN connector
Related Products
• SDP™ Series
• SFL Series
• SCP Series
• SCL Series
• SDU UPS
Applications
• Industrial/Machine Control
• Process Control
• Conveying Equipment
• Material Handling
• Vending Machines
• Packaging Equipment
• DeviceNetTM
• SDN2.5-24-100P and SDN4-24-100LP meet
NEC Class 2
• Amusement Park Equipment
• Narrow width on rail for space critical applications
• Semiconductor Fabrication Equipment
• User-friendly front panel
– Large, rugged, accessible, multiple connection
screw terminations
– Easy installation
Accessories
• Chassis Mount Bracket (SDN-PMBRK2)
• Broad range of product to fit almost any
application – 2.5 A through 40 A, 24 Vdc
• Single and three phase inputs available
• 12 Vdc and 48 Vdc single phase models available
• Highly efficient >90% switching technology
• High MTBF and reliability
• RoHS compliant
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Ï
SDNTM Specifications (Single Phase), 24 Vdc Output
Description
DEMK0 06
ATEX 05 21715U
Catalog Number
SDN 2.5-24-100P
SDN 4-24-100LP
SDN 5-24-100P
SDN 10-24-100P
SDN 20-24-100P
Input
115/230 Vac auto select
Nominal Voltage
85-132/176-264 Vac
-AC Range
-DC Range1
90-375 Vdc
210-375 Vdc
47 - 63 Hz
-Frequency
Nominal Current2
-Inrush current max.
Efficiency (Losses3)
N/A
1.3 A. / 0.7 A
2.1 A / 1.0 A
typ. < 25 A
> 87.5% typ. (8.6 W)
2.2 A / 1.0 A
5 A / 2 A typ.
typ. < 20 A
> 88% typ. (13.1 W)
9 A/ 3.9 A
typ. < 40 A
> 88% typ. (16.4 W)
> 88% typ. (32.7 W)
> 90% typ. (48 W)
Units Fulfill EN61000-3-2
Power Factor Correction
Output
Nominal Voltage
24 Vdc
(22.5 - 28.5 Vdc adj.)
-Tolerance
24 Vdc
24 Vdc
(22.5 - 25.5 Vdc adj.)
(22.5 - 28.5 Vdc adj.)
< ±2% overall (combination Line, load, time and temperature related changes)
< 50 mVpp
-Ripple4
> 30 Vdc, but < 33 Vdc, auto recovery
Overvoltage Protection
Nominal Current
-Current Limit
Holdup Time5
Parallel Operation
2.5 A (60 W)
3.8 A (92 W)
5 A (120 W)
10 A (240 W)
20 A (480 W)
Fold Forward (Current rises, voltage drops to maintain constant power during overload up to max peak current)
> 50 ms
> 100 ms
> 100 ms
> 100 ms
Single or Parallel use is selectable via Front Panel Switch (SDN 2.5, 4 should not be used in parallel as Class 2 rating would be violated.)
General
EMC:
-Emissions
-Immunity
Approvals
Temperature
EN61000-6-3, -4; Class B EN55011, EN55022 Radiated and Conducted including Annex A.
EN61000-6-1, -2; EN61000-4-2 Level 4, EN61000-4-3 Level 3; EN61000-4-6 Level 3; EN61000-4-4 Level 4 input and Level 3 output; EN61000-4-5
Isolation Class 4, EN61000-4-11;
EN60950; UL508 Listed, cULus; UL60950, cRUus, CE (LVD 73/23 & 93/68/EEC). EN61000-3-2, IEC60079-15 (Class 1, Zone 2, Hazardous
Location, Groups A, B, C, D w/ T3A temp class up to 60°C Ambient.) SEMI F47 Sag Immunity. SDN 2.5 & SDN 4 - UL60950 testing to
include approval as Class 2 power supply in accordance with UL1310.
Storage: -25oC...+85oC Operation. -10°-60oC full power with operation to 70°C possible with a linear derating to half power from 60oC to 70oC
(Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation. The relative
humidity is < 90% RH, noncondensing; IEC 68-2-2, 68-2-3.
Humidity
MTBF:
> 820,000 hours
- Standard
> 640,000 hours
Bellcore Issue 6 Method 1 Case 3 @ 40oC
> 600,000 hours
> 510,000 hours
MIL STD 217F @ 30oC
5 years
Warranty
General Protection/
Safety
Protected against continuous short-circuit, overload, open-circuit. Protection Class 1 (IEC536),
degree of protection IP20 (IEC 529) Safe low voltage: SELV (acc. EN60950)
Status Indicators
Green LED and DC OK signal (N.O. Solid State Contact rated 200 mA / 60 Vdc)
Fusing
-Input
Internally fused. External 10 A slow acting fusing for the input is recommended to protect input wiring.
Installation
-Output
Mounting
Connections
Case
-Free Space
HxWxD
(inches/mm)
Weight (lbs/kg)
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required for
wire/loads if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Simple snap-on system for DIN Rail TS35/7.5 or TS35/15 or chassis-mounted (optional screw mounting set SDN-PMBRK2 required).
Input: IP20-rated screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors. 16-12 AWG (0.5-4 mm2) for
flexible conductors. Output: Two connectors per output, connector size range: 16-10 AWG (1.5 - 6 mm2) for solid conductors.
Fully enclosed metal housing with fine ventilation grid to keep out small parts.
25 mm above and below,
25 mm left and right, 10 mm in front
25 mm above and below,
25 mm left and right,
15 mm in front
70 mm above and below, 25 mm left and right,
15 mm in front
4.88. x 1.97 x 4.55
(124 x 50 x 116)
4.88 x 2.56 x 4.55 (124 x 65 x 116)
4.88 x 3.26 x 4.55
(124 x 83 x 116)
4.88 x 6.88 x 4.55
(124 x 175 x 116)
1 lbs (.45 kg)
1.5 lbs (.68 kg)
2.2 lbs (0.1 kg)
3 lbs (1.36 kg)
1. Not UL listed for DC input.
2. Input current ratings are conservatively specified with low input, worst case
efficiency and power factor.
3. Losses are heat dissipation in watts at full load, nominal input line.
4. Ripple/noise is stated as typical values when measured with a 20 MHz,
bandwidth scope and 50 Ohm resistor.
5. Full load, 100 Vac Input @ Tamb = +25°C
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Ï
SDNTM Specifications (Single Phase), 12 Vdc and 48 Vdc Output
Description
DEMK0 06
ATEX 05 21715U
Catalog Number
SDN 9-12-100P
SDN 5-48-100P
SDN 16-12-100P
Input
115/230 Vac auto select
Nominal Voltage
85-132/176-264 Vac
-AC Range
-DC Range1
210-375 Vdc
-Frequency
47-63 Hz, 400 Hz
Nominal Current2
2.0 A / 1.5 A
-Inrush current max.
Typ. < 20 A
Efficiency2 (Losses3)
> 84% typ. (17.28 W)
4 A / 2.3 A
3.3 A / 1.7 A
typ. < 40 A
> 88% typ. (28.8 W)
> 84% typ. (30.72 W)
Units fulfill EN61000-3-2
Power Factor Correction
Output
Nominal Voltage
12 V (11.8-15.2 Vdc Adj.)
48 V (35.8 - 52 Vdc Adj.)
-Line Regulation
< 0.5%
-Load Regulation
< 0.5%
< 1%
-Time & Temp. Drift
< 50 mVpp
Ripple
3
Overvoltage Protection
Nominal Current
-Current Limit4
< 16 Vdc with auto-recovery
< 60 Vdc with auto-recovery
< 16 Vdc with auto-recovery
9 A (108 W)
5 A (240 W)
16 A (192 W)
110% of nominal - Fold Forward (Current rises, voltage drops to maintain constant power during overload up to max peak current)
>20 ms (Full load, 100 Vac Input @ Tamb=+25°C) to 95% output Voltage
Holdup Time5
Supplies will not be damaged with parallel operation
Parallel Operation
Power Back Immunity
12 V (11.6-14.0 Vdc Adj.)
< ±2 % overall (combination Line, load, time and temperature related changes)
Tolerance
16 Vdc
60 Vdc
16 Vdc
General
EMC:
-Emissions
-Immunity
Approvals
Temperature
Humidity
EN61000-6-3, EN61204-3, EN55022 Class B, EN61000-3-2, EN61000-3-3
EN61000-6-2, EN61204-3, EN55024, IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6,
IEC61000-4-8, IEC61000-4-11
UL508 Listed, cULus; UL 60950-1, cURus; CE (LVD 73/23 & 93/68/EEC), (EMC 89/336 & 93/68/EEC). EN61000-3-2;
UL 60079-15 pending (Class 1, Zone 2 hazardous location, Groups IIA, IIB, IIC w/ T3 temp. class up to 60°C Ambient.);
EN60079-15 (ATEX); SEMI F47 Sag Immunity, RoHS
Storage: -25 to +85oC, Operation -10 to +60oC full power; with linear derating to half power from 60 to 70oC
(Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation.
< 90% RH, non-condensing; IEC 68-2-2, 68-2-3
>500,000 hrs
Telcordia/Bellcore, Issue Case 3 @25oC
MTBF:
- Standard
5 years
Warranty
General Protection/Safety
Protected against Continuous short -circuit, Continuous overload, Continuous open circuit. Protection Class 1 (IEC536),
Degree of Protection IP20 (IEC 529) Safe low voltage: SELV (acc. EN60950)
Status Indicators (Visual)
Green LED on when Vout > 75% (with ± 5% tolerance) of nominal output voltage
Status Indicators (Relay)
Normally Open solid state relay - signal active when Vout >70% of nominal output voltage (rated up to 200 mA, 60 Vdc)
Installation
Fusing
-Input
Mounting
Internally fused
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required if
Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Simple snap-on to DIN TS35/7.5 or TS35/15 rail system. Unit should handle normal shock and vibration of industrial use
and transportation without falling off the rail.
Connections
Input: Screw terminals, connector size range: 16-10 AWG (1.5-6mm2) for solid conductors.
Output: Two terminals per output, connector size range: 16-10 AWG (1.5-6mm2) for solid conductors.
Case
Fully enclosed metal housing with fine ventilation grid to keep out small parts.
-Output
70 mm above and below, 25 mm left and right, 15mm in front
-Free Space
H x W x D (inches/mm)
Weight (lbs/kg)
4.88 × 2.56 × 4.55 (124 x 65 × 116)
2.4 (1.05)
1. Input current ratings are specified with low input, line conditions and worst case efficiency
values. Input current at nominal input settings will be typically half these values.
2. Losses are heat dissipation in watts at full load, nominal line.
3. Ripple/ noise is stated as typical values when measured with a 20 MHz bandwidth
scope and 50 Ohm resister.
4.88 × 3.26 × 4.55 (124 × 83 × 116)
3.3 (1.48)
3.3 (1.48)
4. Unit shall not shutdown or ‘hiccup’ during overload or short circuit. Maximum current value
shown shall be maintained indefinitely without damage to the supply. Voltage shall drop
according to amount of overload to protect supply from damage.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDNTM Specifications (Three Phase)
Description
Catalog Number
SDN 5-24-480
SDN 10-24-480
SDN 20-24-480C
SDN 30-24-480
SDN 40-24-480
Input
1Ø or 3Ø
380 - 480 Vac1
1Ø or 3Ø 380-480 Vac
Nominal Voltage
-AC Range
340 - 576 Vac
-DC Range2
450 - 820 Vdc
47 - 63 Hz
-Frequency
Nominal Current3
0.5 A
0.8 A
1.5 A
2.0 A
typ. < 18 A
-Inrush current max.
Efficiency (Losses4)
3Ø 380 - 480 Vac
> 90% typ. (12 W)
3.0 A
typ. < 30 A
> 90% typ. (48 W)
Power Factor
Correction
> 90% typ. (72 W)
> 90% typ. (96 W)
Units Fulfill EN61000-3-2
Output
24 Vdc (22.5 - 28.5 Vdc adj.)
Nominal Voltage
< ±2% overall (combination Line, load, time and temperature related changes)
-Tolerance
< 50 mVpp
-Ripple5
Overvoltage
Protection
Nominal Current
-Peak Current
-Current Limit
> 30 Vdc, but < 33 Vdc, auto recovery
5 A (120 W)
20 A (480 W)
12A,
25A,
2x Nominal Current < 2 sec. 2x Nominal Current < 2 sec.
30 A (720 W)
40 A (960 W)
35A, 2x Nominal Current
< 2 sec.
45A, 2x Nominal Current
< 2 sec
Fold Forward (Current rises, voltage drops to maintain constant power during overload up to max peak current)
> 40 ms
Holdup Time6
Parallel Operation
10 A (240 W)
6A,
2x Nominal Current < 2 sec.
> 28 ms
> 20 ms
5A through 30A units may be passively paralleled by selecting the “P” position of the switch on the unit. The SDN 40 contains active current balancing.
General
EMC:
-Emissions
-Immunity
Approvals
Temperature
MTBF:
- Standard
EN61000-6-3, -4; Class B EN55011, EN55022 Radiated and Conducted including Annex A.
EN61000-6-1, -2; EN61000-4-2 Level 4, EN61000-4-3 Level 3; EN61000-4-6 Level 3; EN61000-4-4
Level 4 input and Level 3 output; EN61000-4-5 Isolation Class 4, EN61000-4-11;
CB Scheme, EN60950; UL508 Listed, cULus; UL60950, cRUus, CE (LVD 73/23 & 93/68/EEC). EN61000-3-2, UL60079-15
Class 1, Zone 2 Hazardous Location, Groups IIA, IIB, IIC w/T3 temp class up to 60°C Ambient.
Storage: -25°C...+85°C Operation. -10°C -60°C full power with operation to 70°C possible with a linear derating to half power from 60°C to 70°C
(Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation. The relative
humidity is < 90% RH, noncondensing; IEC 68-2-2, 68-2-3.
> 1,110,000 hours
> 940,000 hours
> 550,000 hours
> 620,000 hours
> 490,000 hours
MIL STD 217F @ 30oC
5 years
Warranty
General Protection/
Safety
Protected against continuous short-circuit, overload, open-circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC 60529) Safe low voltage:
SELV (acc. EN60950)
Status Indicators
Green LED on when Vout = 18V or greater.
Installation
Fusing
-Input
-Output
Mounting
Connections7
Case
Internally fused
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required for wire/loads
if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Simple snap-on system for DIN Rail TS35/7.5 or TS35/15 or chassis-mounted (optional screw mounting set SDN-PMBRK2 required).
Input: IP20-rated screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors. 16-12 AWG (0.5-4 mm2) for flexible conductors.
Output: Two connectors per output, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors.
Fully enclosed metal housing with fine ventilation grid to keep out small parts.
-Free Space
25 mm above and below, 25 mm left and right,
15 mm in front
HxWxD
(inches/mm)
4.88 x 2.91 x 4.55
(124 x 73 x 116)
4.88 x 3.5 x 4.55
(124 x 89 x 116)
4.88 x 5.9 x 4.55
(124 x 150 x 116)
4.88 x 9.72 x 4.55
(124 x 247 x 116)
4.88 x 11.1 x 4.55
(124 x 282 x 116)
1.7 lbs (.77 kg)
2.16 lbs (.98 kg)
3.97 lbs (1.8 kg)
4 lbs (1.81 kg)
6.6 lbs (2.99 kg)
Weight (lbs/kg)
1. For the SDN 20-24-480C, single phase input is permissible, but output is derated
to 75% (15 Amps @ 24 Vdc).
2. Not UL listed for DC input.
3. Input current ratings are conservatively specified with low input, worst case
efficiency and power factor.
70 mm above and below, 25 mm left and right , 15 mm in front
4. Losses are heat dissipation in watts at full load, nominal input line.
5. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth
scope and 50 Ohm resistor.
6. Full load, 100 Vac Input @ Tamb = +25°C
7. For the SDN 40-24-480, output: one (+) two (-) connectors, size range 16-5 AWG
(1.5016 mm2) solid conductor.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ Series Dimensions
D
W
+ +
Catalog
Number
-
OK
NEC Class 2
Power Supply
24-28 V
Parallel
H
S O LA
).$ #/.4 %1
(!
US LISTED
115/230 VAC 1.3-0.7 A 50/60 HZ
N
D
4.88 (124)
2.56 (65)
4.55 (116)
SDN 16-12-100P
4.88 (124)
3.26 (83)
4.55 (116)
24 Vdc
Power Supply
SDN 2.5-24-100P
U
L
W
SDN 9-12-100P
Single
C
H
12 Vdc
OK
24 VDC / 2.5 A
Dimensions - inches (mm)
L
SDN 2.5-24-100P
4.88 (124)
1.97 (50)
4.55 (116)
SDN 4-24-100LP
4.88 (124)
2.56 (65)
4.55 (116)
SDN 5-24-100P
4.88 (124)
2.56 (65)
4.55 (116)
SDN 5-24-480
4.88 (124)
2.91 (73)
4.55 (116)
SDN 10-24-100P
4.88 (124)
3.26 (83)
4.55 (116)
SDN 20-24-100P
4.88 (124)
6.88 (175)
4.55 (116)
SDN 5-48-100P
4.88 (124)
3.26 (83)
4.55 (116)
48 Vdc
W
D
S O LA
H
Power Supply
SDN 20-24-480C
).$ #/.4 %1
(!
Catalog
Number
Overload
Output:
24 VDC / 20 A
Electronically protected
2428V
+ + - -
OK
Single Use
L1 L2 L3
Parallel Use
Input:
3PH 380/500 VAC
1.7/1.5A/Phase 50/60 Hz
Reset fuse mode
US LISTED
Continuous Mode
U
L
Fuse Mode
C
Dimensions - inches (mm)
H
W
D
SDN 10-24-480
4.88 (124)
5.90 (150)
4.55 (116)
SDN 30-24-480
4.88 (124)
9.72 (247)
4.55 (116)
SDN 40-24-480
4.88 (124)
11.10 (282)
4.55 (116)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Supplies
4
SDN™ Series Mounting
DIN Rail Mounting
Snap on the DIN Rail:
1.Tilt unit slightly backwards
2.Put it onto the DIN Rail
3. Push downwards until stopped
4. Push at the lower front edge to lock
5. Shake the unit slightly to ensure that the retainer
has locked
Alternative Panel Mount: Using the optional SDN-PMBRK2
accessory, the unit can be screw mounted to a panel.
Detachment from DIN Rail:
Chassis Mounting
Dimensions
Instead of snapping a SolaHD SDN™ unit on the DIN Rail,
you can also attach it using the screw mounting set
SDN-PMBRK2.
This set consists of two metal brackets, which replace the
existing two aluminum profiles.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ DeviceNetTM Series
As members of the Open DeviceNetTM Vendors Association
(ODVA), SolaHD has designed two power supplies specifically for DeviceNetTM applications. SolaHD’s SDN DeviceNetTM models meet ODVA specifications for power supplies for
either thin or thick cable applications.
The SDN 4-24-100LP has the highest output current
possible while still meeting the requirements for NEC Class 2
and UL 1310. This is necessary for installations to meet the
National Electrical Code (NEC) or the Canadian Electric
Code (CE code) without the need for secondary fusing.
The SDN 10-24-100P is designed for installations that utilize
the full 8A capability of the Thick Cable system. Note – local
codes may prohibit the use of the full capacity of the power
supply.
Features (General)
UL 508 Listed
IND. CONT.
EQ. E61379
•Power Factor Correction
•SEMI F47 Sag Immunity Standard
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
EMC and
Low Volt.
Directive
•Class 1, Div. 2 Hazardous Locations
•DC Okay Signal
•Industrial Grade Design
• Indefinite short-circuit, overvoltage and
overtemperature protection
• Rugged metal case and DIN connector
•Narrow width on rail for space critical applications
•User-friendly front panel
• Large, rugged, accessible multiple connection
screw terminations
• Easy installation
•High efficiency for cooler operation and less heat losses
•High MTBF & reliability
Features (SDN 4-24-100LP only)
•Meets the requirements of NEC Class 2 & UL 1310
•No derating from -10°C to 60°C, operation to 70°C
possible with a linear derating to half power from
60°C to 70°C.
Related Products
•SDP™ Series
•SCD Series
•SCP Series
•SCL Series
Applications
•High grade and low stress design components
•Industrial Control
•No fans used or required
•Process Control
•RoHS Compliant
•Building Automation
•Five year warranty
•DeviceNetTM
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ DeviceNetTM Specifications
Description
Catalog Number
SDN 5-24-100P
SDN 10-24-100P
Input
115/230 Vac auto select
Nominal Voltage
-AC Range
85-132/176-264 Vac
-DC Range1
210-375 Vdc
47 - 63 Hz
-Frequency
Nominal Current
2
-Inrush current max.
Efficiency (Losses3)
2.2 A / 1.0 A
5 A / 2 A typ.
typ. < 20 A
typ. < 40 A
> 88% typ. (16.4 W)
> 88% typ. (32.7 W)
Units fulfill EN61000-3-2
Power Factor Correction
Output
Nominal Voltage
-Tolerance
24 Vdc
(22.5 - 28.5 Vdc adj.)
< ±2% overall (combination Line, load, time and temperature related changes)
< 50 mVpp
-Ripple4
> 30 Vdc, but < 33 Vdc, auto recovery
Overvoltage Protection
Nominal Current
-Current Limit
5 A (120 W)
10 A (240 W)
Fold Forward (Current rises, voltage drops to maintain constant power during overload up to max peak current)
> 100 ms
Holdup Time5
Parallel Operation
Single or Parallel use is selectable via Front Panel Switch (SDN 2.5, 4 should not be used in parallel as Class 2 rating would be violated.)
General
EMC:
-Emissions
-Immunity
Approvals
Temperature
MTBF:
- Standard
EN61000-6-3, -4; Class B EN55011, EN55022 Radiated and Conducted including Annex A.
EN61000-6-1, -2; EN61000-4-2 Level 4, EN61000-4-3 Level 3; EN61000-4-6 Level 3; EN61000-4-4 Level 4 input and Level 3 output;
EN61000-4-5 Isolation Class 4, EN61000-4-11;
EN60950; UL508 Listed, cULus; UL60950, cRUus, CE (LVD 73/23 & 93/68/EEC). EN61000-3-2, IEC60079-15 (Class 1, Zone 2, Hazardous
Location, Groups A, B, C, D w/ T3A temp class up to 60°C Ambient.) SEMI F47 Sag Immunity. SDN 2.5 & SDN 4 - UL60950 testing to include approval as Class 2 power supply in accordance with UL1310.
Storage: -25oC...+85oC Operation. -10°...-60oC full power with operation to 70°C possible with a linear derating to half power from 60oC to 70oC
(Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation. The relative
humidity is < 90% RH, noncondensing; IEC 68-2-2, 68-2-3.
> 640,000 hours
> 600,000 hours
Bellcore Issue 6 Method 1 Case 3 @ 40oC
5 years
Warranty
General Protection/Safety
Protected against continuous short-circuit, overload, open-circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC 529)
Safe low voltage: SELV (acc. EN60950)
Status Indicators
Green LED and DC OK signal (N.O. Solid State Contact rated 200 mA / 60 Vdc)
Installation
Fusing
-Input
-Output
Mounting
Connections
Case
-Free Space
H x W x D (inches/mm)
Weight (lbs/kg)
Internally fused. External 10 A slow acting fusing for the input is recommended to protect input wiring.
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required
for wire/loads if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Simple snap-on system for DIN Rail TS35/7.5 or TS35/15 or chassis-mounted (optional screw mounting set SDN-PMBRK2 required).
Input: IP20-rated screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors. 16-12 AWG (0.5-4 mm2) for flexible
conductors. Output: Two connectors per output, connector size range: 16-10 AWG (1.5 - 6 mm2) for solid conductors.
Fully enclosed metal housing with fine ventilation grid to keep out small parts.
25 mm above and below, 25 mm left and right, 15 mm in front
70 mm above and below, 25 mm left and right, 15 mm in front
4.88 x 2.56 x 4.55 (124 x 65 x 116)
4.88 x 3.26 x 4.55 (124 x 83 x 116)
1.5 lbs (.68 kg)
2.2 lbs (0.10 kg)
1. Not UL listed for DC input.
2. Input current ratings are conservatively specified with low input, worst case
efficiency and power factor.
3. Losses are heat dissipation in watts at full load, nominal input line.
4. Ripple/noise is stated as typical values when measured with a 20 MHz,
bandwidth scope and 50 Ohm resistor.
5. Full load, 100 Vac Input @ Tamb = +25°C
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ Series Redundant Options
The SDN Series standard options allow for operation in a
wide variety of applications. With the addition of an external redundancy module, the SDN can also be used for true
redundant operation including 2N and N+x configurations.
All SDN units include built in current sharing for parallel and
redundant operation. All models ending in P also include
a DC OK status relay contact. The external modules
SDN 2.5-20RED and SDN 30/40RED increase the reliability
by isolating the supplies and adding more signal options.
Paralleling for increased power does not require the use of
these modules.
Module Compatibility
Two separate modules are available to provide the maximum
flexibility in size, cost and signaling capability. Refer to the
chart below for information on which module can be used for
each SDN power supply.
Power Rating – A simple Yes or No indication that this module
can or cannot handle the power rating of that power supply.
Input/Output Signals – Yes indicates that each power supply
would have an independent relay contact to provide power
supply status, and the DC bus output from the redundant
module has it’s own DC OK relay contact. Output only
indicates that only the output of the redundant module
would have a DC OK relay contact.
EMC and
Low Volt.
Directive
Features
• DC OK Relay Contact
• True Isolation
• High availability
• SDN features and quality
Applications
• Process Control
• Remote Location
• Critical Production
Redundancy Module Compatibility Chart
Single Phase SDN Series
SDN 2.5-20RED
SDN 30/40RED
Power Rating
Input / Output Signals
Power Rating
Input / Output Signals
SDN 2.5-24-100P*
Yes
Yes
Yes
Yes
Power Rating
Input / Output Signals
Power Rating
Input / Output Signals
SDN 5-24-480
Yes
Output Only
Yes
Yes
SDN 4-24-100P*
Yes
Yes
Yes
Yes
SDN 5-24-100P
Yes
Yes
Yes
Yes
SDN 10-24-100P
Yes
Yes
Yes
Yes
SDN 20-24-100P
Yes
Yes
Yes
Yes
SDN 20-24-480
Yes
Output Only
Yes
Yes
SDN 30-24-480
No
N/A
Yes
Yes
SDN 40-24-480
No
N/A
Yes
Yes
Three Phase SDN Series
SDN 2.5-20RED
SDN 30/40RED
SDN 10-24-480
Yes
Output Only
Yes
Yes
* Paralleling will violate Class 2 current limits.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDN™ Redundant Series Specifications for SDN2.5-20RED and SDN 30/40RED
Catalog Number
Description
SDN 2.5-20RED
SDN 30/40RED
Concept
By means of a separate redundancy module, you can interconnect several identical SDN power supply units in a N+1 redundant mode. These external
modules decouple the power supply outputs from each other so that, in case of failure, one power supply unit cannot overload the other units. The
modules incorporate DC OK relay contacts. The switch on front of the SDN power supply should be placed in parallel mode (not single mode) when
power supplies are used with redundant module.
Electrical Characteristics
Voltage
24 Vdc
-Nominal Value
35 V
-Max. Rated
Voltage Drop
Typ. 0.6 V
-Vin -> Vout
Current Handling Capacity
-Maximum Value
20 A
40 A
Yes
Inverse Battery Protection
Via captive screw terminals
Connection
-Connector size range
Solid: 16-10 AWG (1.5 - 6 mm2)
Stranded: 16-12 AWG (1.5 - 4 mm2)
Solid: 16-5 AWG (1.5 - 16 mm2)
Stranded: 16-8 AWG (1.5 - 10 mm2)
Note: GND must be connected to module for voltage monitor to operate properly.
See Connectors and Wiring diagrams on next page.
Relay Contacts
DC Okay Contacts (qty) description
(1) Vout “OK” - N.O. Contact
(2) Vin “OK” - N.O. Contact
(1) Vout “OK” - N.O. & N.C. Contact
> 18 Vdc ±5%
-Voltage Set Point
30 Vdc @ 2A / 250 V @ 2A
-Contact Rating
Vout “OK” Green LED
DC OK LED
> 18 Vdc ±5%
-Voltage Set Point
Dimensions
H x W x D - inches (mm)
Free Space for Ventilation inches (mm)
Weight lbs (kg)
4.88 in x 1.97 in x 4.55 in
(124 mm x 50 mm x 116 mm)
4.88 in x 2.56 in x 4.55 in
(124 mm x 65 mm x 116 mm)
Above/Below: 0.39 in. (10 mm) recommended
Left/Right: 0.39 in. (10 mm) recommended
1.38 (625)
1.43 (646)
General
Ambient Temperature
Storage: -25°C...+85°C Operation: -10°C...+60°C full power with operation to 70°C possible with a
linear derating to half power from 60°C to 70°C (Convection cooling, no forced air required). Operation up
to 50% load permissible with sideways or front side up mounting orientation. The relative humidity is
< 90% RH, noncondensing.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Wiring Diagram for SDN 2.5-20RED
Single
Single
Parallel
Parallel
Notes:
1. The Common (marked “COM -“) connection to the module is required for voltage monitoring (DC OK Contacts), and is not meant to be
part of the current path from the power supply to the load.
2. Protective earth connection only provides protective ground to the metal case of the module. This connection is isolated from the
positive and common connections.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Supplies
4
Wiring Diagram for SDN 30/40RED
Single
Parallel
Single
Parallel
Notes:
1. The Common (marked “COM -“) connection to the module is required for voltage monitoring (DC OK Contacts), and is not meant to be
part of the current path from the power supply to the load.
2. Protective earth connection only provides protective ground to the metal case of the module. This connection is isolated from the
positive and common connections.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDP™ Low Power DIN Rail Series
The compact, lightweight DIN Rail power supplies come
in output voltages from 5 to 48 Vdc and power ratings of
up to 100 Watts. These extra small, efficient units are
designed specifically for the industrial environment. Each
unit is rated from -10ºC to 70ºC, with no derating necessary
until above 60ºC.
Many extra “industrial” features are standard for the
SDP PowerBoostTM overload circuitry can start up
industrial loads (i.e. motors, relays, solenoids and DC-DC
converters), that can cause ordinary power supplies to
foldback or shutdown. Each unit contains a DC indicator
and front panel adjustment potentiometer. With the SolaHD
SDP series, you can count on a high grade design.
UL 508 Listed
IND. CONT.
EQ.E6I379
Features
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
EMC and
Low Volt.
Directive
Related Products
• Ultra slim 15W footprint
• SDN™ Series
• No tools required for mounting
• SCP Series
• Adjustable output
• SCL Series
• PowerBoostTM industrial overload design
Applications
• Overvoltage, short circuit protection
• NEC Class 2 Current Limited
• Industrial Control
• Continuous short circuit protection
• Process Control
• Low output noise
• Machine Control
• Screw terminal connections
• Building Automation
• RoHS Compliant
• Instrumentation
• Three year warranty
Selection Table
Catalog Number
DC Output Voltage
Output Current
SDP 5-5-100T
5-6V
5A
SDP 2-12-100T
10 - 12 V
3 - 2.5 A
SDP 3-15-100T
12 - 15 V
4.2 - 3.4 A
SDP 1-48-100T
48 - 56 V
1A
SDP 06-24-100T
0.6 A
SDP 1-24-100T
1.3 A
SDP 2-24-100T
24-28 Vdc
2.1 A
SDP 4-24-100LT
3.8 A
SDP 4-24-100RT*
4.2 A
Ripple / Noise
Size (H x W x D)
2.95 in x 1.77 in x 3.58 in
(75 mm x 45 mm x 91 mm)
<50 mVpp
2.95 in x 0.9 in x 3.8 in
(75 mm x 22.8 mm x 96.7 mm)
2.95 in x 1.77 in x 3.58 in
(75 mm x 45 mm x 91 mm)
2.95 in x 2.85 in x 3.8 in
(75 mm x 72.5 mm x 96.7 mm)
* NEC Class 1
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDP™ Series Specifications (24 V models)
Description
Catalog Number
SDP 06-24-100T
SDP 1-24-100T
SDP 2-24-100T
SDP 4-24-100LT
SDP 4-24-100RT
Input
85-264 Vac, 90-375 Vdc
Input Voltage1
85-132 / 176-264 Vac, 210-375 Vdc
47-63 Hz
Input Frequency
Input Current
0.4 A / 0.25 A
0.7 A / 0.4 A
1.1 A / 0.7 A
Losses
2.2 A / 1.2 A
> 25 ms
Hold-Up Time
Efficiency
1.8 A / 1.0 A
Not required. Unit provides internal fuse (T3A, not accessible)
External Fusing
> 80% typ.
> 83% typ.
> 86% typ.
> 88% typ.
< 3.75 W typ.
< 6.1 W typ.
< 8.1 W typ.
< 12 W typ.
Output
24 V (22.5 - 28.5 Vdc Adj.)
Output Voltage
24 V (24 - 25.7 Vdc Adj.)
< 50 mVpp
Ripple/Noise2
> 26 Vdc, but < 27.2
Vdc, auto recovery
> 30 Vdc, but < 33 Vdc, auto recovery
Overvoltage Protection (OVP)
Output Noise
Suppression
Rated Continuous
Loading
24 V (22.5 - 28.5 Vdc Adj.)
Static 0.5% Vout, dynamic + 2% Vout overall\
Voltage Regulation
> 30 Vdc, but < 33 Vdc,
auto recovery
Radiated EMI values below EN61000-6-2
0.63 A @ 24 Vdc /
0.54 A @ 28 Vdc
1.3 A @ 24 Vdc /
1.1 A @ 28 Vdc
2.1 A @ 24 Vdc /
1.8 A @ 28 Vdc
3.8 A @ 24.5 Vdc
4.2 A @ 24.5 Vdc /
3.6 A @ 28 Vdc
Continuous operation at overload/short-circuit: up to 1.5 x Nominal Current Continuous
Overload Behavior
Unit is continuously protected against short-circuit, overload and open-circuit.
Protection
35 V
Power Back Immunity
Installation
Status Indicators
Green LED on, when Vout “OK”.
Case & Mounting
Molded plastic housing using UL 94 approved flameproof material rating 94V-2.
Simple snap-on to DIN TS35/7.5 or TS35/15 rail system.
Dimensions
(H x W x D) (in/mm)
2.95 x 0.9 x 3.8
(75 x 22.8 x 96.7)
Weight - lbs (kg)
0.35 lbs (.16 kg)
Mounting Orientation
2.95 x 1.77 x 3.58 (75 x 45 x 91)
2.95 x 2.85 x 3.8
(75 x 72.5 x 96.7)
0.5 lbs (.23 kg) 
0.7 lbs (.32 kg)
Standard: Vertical; Optional: Horizontal or on top (Contact Technical Services).
Ventilation/Cooling
•Free space for cooling
Normal convection, no fan required; Above/below: 25 mm recommended.
Connection
•Connector size range
Input: screw terminals, connector size range: 20-12AWG (1.5 - 6 mm2) for solid or stranded conductors.
General
Temperature
MTBF
Humidity  
Storage: -25°C...+85°C Operation: -10°...+60°C full power with linear derating to half power from 60°C to 70°C.
(Convection cooling, no forced air required).
> 500,000 hours according to Telcordia/Bellcore Document SR-332, Issue 1.
Up to 90% RH, noncondensing; IEC 68-2-2, 68-2-3
Electromagnetic
Emissions (EME)
EN61000-6-3 (Includes EN61000-6-4) Class B (EN 55022) incl. Annex A
Electromagnetic
Immunity (EMI)
EN61000-6-2 (Includes EN61000-6-1) (EN55024) Criterion A: no derogation of performance
SELV (acc. EN60950)
Safe Low Voltage
Protection Class/Voltage
IP20 (IEC529), Protection Class 1 (IEC536)
3 years
Warranty
Safety
CB Scheme, EN60950, UL60079-15 (Class 1, Zone 2 Hazardous Locations, Temp Class T3), UL508 Listed, cULus, UL 60950, cURus, CE (LVD 73/23 & 93/68/EEC). (EMC
89/336 & 93/68/EEC). EN61000-3-2, NEC Class 2 power supply acc. To NFPA 70 art. 725-41 (a)(2).3
Notes:
1. Not UL listed for DC input.
2. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth scope and 50 Ohm resistor.
3. For all models except SDP 4-24-100LT.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDP™ Series Specifications (Other Voltages)
Description
Catalog Number
SDP 5-5-100T
SDP 2-12-100T
SDP 3-15-100T
SDP 1-48-100T
Input
85-264 Vac, 90-375 Vdc
Input Voltage1
47-63 Hz
Input Frequency
0.6 A @ 102 Vac;
0.33 A @196 Vac
Input Current
1.0 A @ 102 Vac;
0.6 A @ 196 Vac
Not required. Unit provides internal fuse (T3A, not accessible)
External Fusing
> 25 ms
Hold-Up Time
> 80% typ.
Efficiency
Losses
<1.0 A @ 100 Vac;
<0.6 A @ 196 Vac
7.5 W typ.
> 86% typ.
8.1 W typ.
> 90% typ.
< 8.1 W typ.
Output
Output Voltage
5 - 5.5 Vdc (5 - 6 min adj.)
12 Vdc (9.9 - 12.1 min adj. )
Voltage Regulation
> 6.7 Vdc
> 18 Vdc
lout = 5A @ Vout = 5.1V
> 56 Vdc
3A @ 10 Vdc
2.5A @12 Vdc
4.2A @ 12 Vdc
3.4A @ 15 Vdc
Up to 1.05A @ 48 V
0.9A @ 56 V
Continuous operation at overload/short-circuit: up to 1.5 x Nominal Current Continuous
Overload Behavior
Unit is continuously protected against short-circuit, overload and open-circuit.
Protection
Power Back Immunity
> 20 Vdc
Radiated EMI values below EN61000-6-2
Output Noise Suppression
Rated Continuous Loading
48 Vdc (48 - 56 min adj.)
< 50 mVpp
Ripple/Noise2
Overvoltage Protection (OVP)
15 Vdc (11.9 - 15.1 min adj.)
< 2% Dynamic; < 0.5% Static
10 V
22 V
80 V
Installation
Status Indicators
Green LED on, when Vout “OK”.
Case & Mounting
Molded plastic housing using UL 94 approved flameproof material rating 94V-2.
Simple snap-on to DIN TS35/7.5 or TS35/15 rail system.
Dimensions
(H x W x D) (in/mm)
2.95 x 1.77 x 3.58 (75 x 45 x 91)
0.5 lbs (.23 kg)
Weight - lbs (kg)
Mounting Orientation
Standard: Vertical; Optional: Horizontal or On Top (Contact Technical Services).
Ventilation/Cooling
•Free space for cooling
Normal convection, no fan required; Above/below: 25 mm recommended.
Connection
•Connector size range
Input: screw terminals, connector size range: 20-12 AWG (1.5 - 6 mm2) for solid or stranded conductors.
General
Temperature
MTBF
Humidity  
Storage: -25°C...+85°C Operation: -10°...+60°C full power with linear derating to half power from 60°C to 70°C.
(Convection cooling, no forced air required).
> 500,000 hours according to Telcordia/Bellcore Document SR-332, Issue 1.
Up to 90% RH, noncondensing; IEC 68-2-2, 68-2-3
Electromagnetic Emissions
(EME)
EN61000-6-3 (Includes EN61000-6-4) Class B (EN 55022) incl. Annex A
Electromagnetic Immunity
(EMI)
EN61000-6-2 (Includes EN61000-6-1) (EN55024) Criterion A: no degradation of performance
SELV (acc. EN60950)
Safe Low Voltage
Protection Class/Voltage
IP20 (IEC529), Protection Class 1 (IEC536)
3 years
Warranty
Safety
CB Scheme, EN60950, UL60079-15 (Class 1, Zone 2 Hazardous Locations, Temp Class T3), UL508 Listed, cULus, UL 60950, cURus,
CE (LVD 73/23 & 93/68/EEC), (EMC 89/336 & 93/68/EEC). EN61000-3-2, NEC Class 2 power supply acc. To NFPA 70 art. 725-41 (a)(2).3
Notes:
1. Not UL listed for DC input.
2. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth scope and 50 Ohm resistor.
3. Not to exceed 30 watts total.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCP-X Extreme Environment Series
Selection Table
Catalog Number
Output Current
Output Voltage
Output Power
3.8 A
24 Vdc
95 W
SCP 100S24X-CM
SCP 100S24X-CP
SCP 100S24X-DVN
Chassis Mount (-CM) Applications
This extreme environment power supply is ideal for outdoor
or wet chassis-mount applications (Figure 1).
Ï
9HAO
IND. CONT. EQ.
Also listed I.T.E.
Power Supply
E234790
Class 1 Zone 2
AEx nA IICT4
Ex nA IICT4 U
• Input connector: 3-pole, male receptacle externally threaded
with ½-14 NPT mounting thread.
Ï
• Output Connector: 4-pole, female receptacle externally
threaded with ½-14 NPT mounting thread.
DEMK0 06 ATEX 05
21715U
EEX nA IIC T4 U
-40ºC ≤ Tam ≤ +60ºC
The SCP-X is a rugged power supply designed for use in
extreme environments. The metal case reduces costs by
eliminating separate enclosures. Quick change connectors
simplify connectivity for distributed I/O devices on industrial
machinery. This model provides 24 Vdc output with limited
power to meet Class 2 requirements. Three models are
currently offered based on application.
Features
Control Power (-CP) Applications
The SCP100S24X-CP is designed for Control Power
applications where a grounded power supply output is
required (Figure 2).
• Input connector: 3-pole, male receptacle externally threaded
with ½-14NPT mounting thread.
• Output connector: 4-pole, female receptacle internally
threaded with ½-14 NPT mounting thread.
• IP66/67 Versatile/NEMA 4X Rated
DeviceNetTM (-DVN) Applications
• 24 Vdc, 115/230 Vac, 3.8A Nominal Current
The SCP100S24X-DVN is designed for DeviceNetTM
applications where an isolated output from ground is
required (Figure 2).
• Listed power supply for stand alone applications
• Can be mounted in any orientation without limitation
• Universal input
o
• High ambient temperature up to 60 C without derating
• DC OK Green LED
• Input connector: 3-pole, male receptacle externally threaded
with ½-14NPT mounting thread.
• Output connector: 4-pole, female receptacle internally
threaded with ½-14 NPT mounting thread.
• Worldwide approvals
• Five Year Warranty
Recommended Electrical Connections(1)
Related Products
Catalog Number
• SDN Series
SCP 100S24X-CM
• SCP Series
SCP 100S24X-CP
Input 3-PIN Connections
Daniel Woodhead
P/N 103000A01FXX0(2)
SCP 100S24X-DVN
SCP-DINBKT
Daniel Woodhead
P/N 104002A01FXX0(2)
Turck RSM46*M
*length in meters
1. Connections to be provided by the user.
Accessory
Catalog
Number
Output 4-PIN Connections
2. XX is the length of the cordset in foot.
Description
Mounting bracket to secure SCP-X to
DIN Rail (included)
Approx. Ship
Weight lbs (kg)
1 (.45)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCP100S24X-CM Mechanical Diagrams
Electrical Connections
1. V- is isolated from ground. V- is a separately derived source so it is
permissible to bond to ground if required in the application.
Top View
Side View
Bottom View
Figure 1
SCP100S24X-CP and SCP100S24X-DVN Mechanical Diagrams
Top View
Electrical Connections
Side View
1. 0 Vdc connections are internally bonded to ground
Bottom View
2. V- is isolated from ground. V- is a separately derived source so it is
permissible to bond to ground if required in the application.
Figure 2
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Supplies
4
SCP-X Specifications
Input
Any voltage from 100 to 240 Vac Input
Nominal Voltage
85-264 Vac Universal Input
-AC Range
100-353 Vdc
-DC Range
1.6A/0.7A
Nominal Current
1
Typ. <25A
-Inrush current max.
0.95
Power Factor Correction2
50/60/400 Hz
Frequency
Output
Power Back Immunity
35 V
Overvoltage Protection
25-25.5 Vdc, autorecovery
24 Vdc
Nominal Voltage
Tolerance
< +/-2% overall (combination line, load, time and temperature related changes)
- Line Regulation
< 0.5%
- Load Regulation
< 0.5%
< 1%
- Time & Temp. Drift
< 50 mVpp
Ripple3
3.8A
Total Nominal Current
Holdup Time
> 25 ms (Full load, 100 Vac Input @ Tamb=+25o) to 95% output voltage
General
IP66/67 versatile ingress protection; also meets UL50 Type 4X enclosure.
Case
Min. Required Free Space
1 in. (25 mm) all sides but mounted base (permissible to mount in any orientation)
4.7 x 7 x 1.8 (119 x 178 x 46)
H x W x D (inches/mm)
2.6 lbs (1.16 kg)
Weight - lbs (kg)
EMC
Emissions
EN61000-6-3, EN61204-3, EN55022 Class B, EN61000-3-2, EN61000-3-3
Immunity
EN61000-6-2, EN61204-3, EN55024, IEC61000-4-2, IEC61000-4-3, IEC61000-4-4,
IEC61000-4-5, IEC61000-4-6, IEC61000-4-8, IEC61000-4-11
Approvals
UL508, cULus; UL60950, cULus; UL60079-15 cRUus; IEC60950; CE (LVD 73/23 & 93/68/EEC). (EMC 89/336 & 93/68/EEC). EN61000-3-2,
EN50021 (Class 1, Division 2 Hazardous Location, EEX nA IIC T4 U up to 60°C Ambient.)4
Temperature
Storage: -40o to +85oC, Operation: -40o to +60oC full power with linear derating to half power from 60o to 70oC (Convection
cooling, no forced air required). Operation up to 100% load permissible with sideways or front side up mounting orientation.
Up to 100% RH with condensation.
Humidity
Altitude
0 to 3,000 meters (0 to 10,000 feet)
Vibration
1.0 gravity (g) peak, 10-500 Hz (random wave).
Passed random vibration test conditions for 3 axes for 60 minutes duration while energized and operating.
Shock
4 g peak, 22 milliseconds half-sine pulse, 3 times on 6 faces while energized and operating
5 years
Warranty
MTBF
General Protection/Safety
>500,000 hours according to Telecordia/Bellcore SR-332 Issue 1, (Vin 120 Vac, Tamb=40oC)
Protected against continuous short-circuit, continuous overload, continuous open circuit. Protection Class 1 (IEC536),
degree of protection IP66/67 versatile (IEC 529). Safe low voltage: SELV (acc. IEC60950)
DC OK LED
Status Indicators - Visual
Installation
Fusing
-Input
Internally fused, fuses not replaceable
-Output
Inherently limited current to meet Class 2 requirements per UL1310
Mounting
Connections
Chassis mounted via built in mounting tabs. Removal and replacement of the unit shall be possible from front of panel.
Input: 3 pin IP67 molded plug (quick disconnect). Output: 4 pin IP67 molded receptacle (quick disconnect).
1. Input current ratings are specified with low input, line conditions, worst case
efficiency values and power factor.
2. Power Factor Correction at 50/60 Hz only.
3. Ripple/noise is stated as typical AC values when measured with a 20 MHZ,
bandwidth scope and 50 Ohm termination.
4. Additional installation requirements apply when used in hazardous locations
(refer to user manual).
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCP Series, 30 Watt; Single, Dual and Triple
Selection Table
Output Voltages
Low Profile
Catalog
Number
Description
V1
Vdc
V2
A
Vdc
V3
A
Vdc
A
Min
Load
V1
A
Efficiency
%
30 Watts; Switching DC Power Supply
3.3 V
3.3
6.0
-
-
-
-
0
≥ 62
SCP 30S5-DN
5V
5
6.0
-
-
-
-
0
≥ 70
SCP 30S12-DN
12 V
12
2.5
-
-
-
-
0
≥ 75
SCP 30S15-DN
15 V
15
2.0
-
-
-
-
0
≥ 75
SCP 30S24-DN
24 V
24
1.3
-
-
-
-
0
≥ 77
SCP 30S48-DN
48 V
48
0.6
-
-
-
-
0
≥ 77
SCP 30D12-DN
Dual O/P +/- 12 V
12
1.2
-12
1.2
-
-
0.12
≥ 68
SCP 30D15-DN
Dual O/P +/- 15 V
15
1.0
-15
1.0
-
-
0.15
≥ 68
SCP 30D512-DN
Dual O/P 5 V & 12 V
5
3.0
12
1.2
-
-
0.3
≥ 68
SCP 30D524-DN
Dual O/P 5 V & 24 V
5
3.0
24
0.6
-
-
0.3
≥ 68
SCP 30T512-DN
Triple O/P 5/12/12 V
5
3.0
-12
0.6
12
0.6
0.3
≥ 68
SCP 30T515-DN Triple O/P 5/15/15 V
5
3.0
-15
0.5
15
0.5
0.3
≥ 68
SCP 30S3.3-DN
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
EMC and
Low Volt.
Directive
These switchers are compact, rugged power supplies
designed to power many of your industrial control and
instrumentation devices and equipment, with high reliability
and tight regulation through the most difficult factory-floor
conditions around the globe. “User friendly” applies to these
unique power supplies that feature easy-to-install DIN Rail
and chassis mounting. Terminations are also easy to access
(AC and DC terminations are well separated) and simple to
wire. Safety is another aspect where the SCP distinguishes
itself. The encapsulated design meets IP20 specifications,
and the wide range of voltages will reliably support almost
any low-power device in your cabinet or system for years
to come.
Features
• International approvals for global use
• DIN Rail or Chassis Mount
• Rugged, encapsulated design to resist environment
• IP20 protection
• Many output voltages, 3.3-48 Volts; single, dual, triple
Please order using the following model number suffixes:
-DN: Low Profile – DIN Rail or Chassis Mount
(ie: SCP30S3.3-DN).
B-DN: Slim Line – DIN Rail Mount Availability Only
(ie: SCP30S3.3B-DN).
Note: Slim line version not available on SCP30D512-DN
Options and Accessories
• SCP-MDC – Pair of metal DIN clips
• SCP-PDC – 1 plastic DIN clip with lever for
removal from rail
Standards
• UL60950, E137632
• EN60950
• CE and IP20
• Five year warranty
Packaging and Mounting Specifications
• Simple snap-on for DIN Rail TS35/7.5 or TS35/15
• M3 screw clamp terminations
• Chassis mounting possible on -DN Low-Profile versions
by removing DIN clips (simply unscrew at the back of
the unit).
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCP Series
Specifications
Parameter
Dimensions – mm (inches)
Condition
Value
Low Profile DIN Rail (-DN) or Chassis Mount*
D = 4.2(.16)
Input
AC Input Voltage
85…264 Vac
DC Input Voltage
100…375 Vdc
Input Frequency
50/60 HZ
Filtering EMI/RFI
EN 55011/B, 55022/B
Switching Frequency
Typ. 100 kHz
Input Fusing Required
Use 2.0 A Slow Fuse
5 4 3
2 1
≤2%, Vout
Line Regulation
Vin=min/max 25°C
Iout = max, 25°C
≤+0.5%, Vout
Load Regulation
Iout = 10…90…10%, 25°C
Vin = 230Vac, 25°C
≤+0.5%, Vout
105…130% Inom
Load Regulation Timing
10...90...10%, 25°C
<4 ms
Temperature Coefficient
Tamb = -25...+65°C
0.01%/K
Tamb >50°C
General
Vin =230 Vac
Tamb = 25°C
Case Temperature Rise at
Full Load
>50 ms
Slim Line DIN Rail Mount only (B-DN)
45...+85°C
45 K max
acc. MIL-HDBK-217F
1 2 3 4 5
800,000 hrs
EN61000-4-2, 3, 4, 5
Transient Protection
Convection
Cooling
Weight - lbs (kg)
65(2.55)
* Unscrew DIN connector for chassis mounting.
0.75 lbs (.34 kg)
0.84 lbs (.38 kg)
Case Material/Potting
UL94-VO
CSA Power Supply Class
Level 3
Protection
IP20
Visual Indicators
Green LED indicates
DC OK for B-DN Slim
Line versions only
Front View
Side View
102 (4.0)
MTBF at 25°C (input/output)
53(2.08)
113 (4.43)
Storage Temperature
6
(.24)
2/3/5%/K max
-25…+65°C
Operating Temperature
7
90 (3.53)
Holdup Time
33(.1.29)
Continuous
Overload/Short Circuit
Derating Single/Dual/Triple
6
4.5
Overcurrent Protection
120(4.71)
Vin=min, Iout=max, 25°C
106(4.16)
Noise
Front View
115(4.51)
≤1%, Vout
(.18)
Vin=min, Iout=max, 25°C
57.5(2.26)
V1 ≤ ±1%, V2/3 ≤ ±3%
Ripple
Side View
Output
Vin = 230V, Iout = max, 25°C
Output Voltage Accuracy
6 7
Dimensions (H x W x D)
• Low Profile “-DN”
4.72 x 2.55 x 1.29 inches (120 x 65 x 33 mm)
(Takes up 2.55 inches or 65 mm on DIN Rail)
68(2.67)
Pin-Out
SCP 30
• Slim Line “B-DN”
4.72 x 1.29 x 2.68 inches (120 x 33 x 68 mm)
(Takes up 1.29 inches or 33 mm on DIN Rail)
35(1.37)
1
2
3
4
5
6
7
RETURN
+V1
IN
IN
-V2
COM
+V1
IN
IN
COM (V1)
+V1
COM V3
+V3
IN
IN
COM (V1)
COM (V2/3)
+V1
+V3
IN
IN
Single
Dual sym
Dual asym
Triple
-V2
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCL Series, 4 and 10 Watt CE Linears
Selection Table
Output Voltages
Catalog
Number
Description
V1
Vdc
V2
A
V3
Vdc
A
Vdc
A
4 Watt; Linear DC Power Supply; DIN Rail Mount
SCL 4D12-DN
Dual O/P ±12 V
12
0.13
-12
0.13
-
-
SCL 4D15-DN
Dual O/P ±15 V
15
0.1
-15
0.1
-
-
10 Watt; Linear DC Power Supply; DIN Rail Mount
UL 508
Listed
IND. CONT.
EQ.E6I379
UL 60950
E137632
CUL/CSAC22.2
No. 234-M90
EMC and
Low Volt.
Directive
The 4 and 10 Watt encapsulated linears are available in dual
and triple outputs for applications with sensitive electronics and analog circuitry. The rugged enclosed encapsulated
package, with screw terminals and DIN Rail clips, make for
easy installation and maintenance. These low-noise modules
are capable of being DIN Rail or Chassis mounted.
Features
•
•
•
•
•
Quiet, low noise DC Linear technology
DIN Rail or Chassis mount for easy installation
Rugged encapsulated design
Global specifications including CE and UL 508
Two year warranty
Packaging and Mounting Specifications
SCL 10D12-DN
Dual O/P ±12 V
12
0.35
-12
0.35
-
-
SCL 10D15-DN
Dual O/P ±15 V
15
0.3
-15
0.3
-
-
SCL 10T512-DN Triple O/P, 5 V ±12 V
5
0.2
12
0.3
-12
0.3
Triple O/P, 5 V ±15 V
5
0.2
15
0.25
-15
0.25
SCL 10T515-DN
Note: Dual output units can be series connected for 24V or 30V
applications.
Standards
•
•
•
•
UL60950, E137632
EN60950
CE and IP20
UL 508 Listed
Dimensions (H x W x D)
• 4 watt: 4.31 x 2.0 x 0.90 inches
110 x 51 x 23 mm
• 10 watt: 4.71 x 2.55 x 1.29 inches
120 x 65 x 33 mm
• Simple snap-on for DIN Rail TS35/7.5 or TS35/15
• M3 screw clamp terminations
• Chassis mounting possible on -DN Low-Profile
versions by removing DIN clips (simply unscrew at the
back of the unit).
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCL Series
Specifications
Condition
Value
SCL 4 Watt Linear
D =
4.5(.18)
Input
Input Frequency
47-63 Hz
Input Current
115/230 V
10 Watt: 0.2 A/0.1 A max
4 Watt: 0.1 A/0.05 A max
Efficiency
Typ. 50%
Filtering
10 Watt Only: VDE 871/B
1
Output
3
5
95(3.73)
115/230 ±10% Vac
Field Selectable
Side View
AC Input Voltage
110(4.31)
Parameter
Dimensions – mm (inches)
Front View
<5 mVpp
Noise
Vin=min, Iout=max, 25°C
<5 mVpp
Regulation Accuracy
100...50%, 25°C
<0.05%
Load Regulation Timing
10...90...10%, 25°C
100 ms
Temperature
Coefficient
TA = -25...+65°C
0.01%/K typ.
Holdup Time
min. 20 ms
Overload/Short Circuit
Continuous
0
115V 230V
7.5
Vin=min, Iout=max, 25°C
23(.90)
(.29)
Ripple
55(2.16)
Fixed, preset
Trimming
39(1.53)
6
(.24)
51(2.0)
Pin-Out
SCL 4
1
3
5
6
7
8
Dual
12/15V
COM 12/15V
-12/-15V
IN
IN
IN
General
EN 55 011, Level B
TA > 50°C
3%/K
-40...+85°C
Cooling
Convection
Weight - lbs (kg)
10 Watt: 1.2 lbs (.55 kg)
4 Watt: 0.44 lbs (.20 kg)
Case Material/Potting
UL94-VO
Protection Class
5
<0.05 mA
Storage Temperature
SELV
4
Front View
120(4.71)
Derating
3
>100 MOhm
10 W: -20...+70°C
4 W: -25...+70°C
Operating
Temperature
2
106(4.16)
2 cm side, middle case
1
115(4.51)
Leakage Current
V = 230 Vac, 50 Hz
3.0k Vac, EN 60 950
57.5(2.26)
Isolation Resistance
TA = 25°C
Side View
Isolation Voltage
(input/output)
D =
4.2(.16)
EN 61 000-4-2, Level 4
ENV 50 140 (10 V/m)
EN 61 000-4-4, Level 4
ESD
HF
Burst
4.5
Inducted Noise
SCL 10 Watt Linear
(.18)
Conducted Emissions
0 115V
Class 2
33(1.29)
6
(.24)
230V
53(2.08)
65(2.55)
Pin-Out
SCL 10
1
Dual
-12/15V
Triple
-12/15V
2
3
4
GND 12/15V
5V
GND 12/15V
COM 5V
5
6
7
8
12/15V
IN
IN
IN
12/15V
IN
IN
IN
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCD Series, Encapsulated, Industrial DC to DC Converter
These compact, rugged DC to DC converters are power
supplies designed to power industrial control instrumentation
devices and equipment where AC power is not convenient
or accessible. With high reliability and wide input range,
these units can operate through the most difficult factoryfloor conditions around the globe. “User friendly” applies to
these unique power supplies that feature easy-to-install DIN
Rail and chassis mounting. Terminations are also easy to
access and simple to wire. Encapsulated design meets IP20
specifications for use in harsh environments.
Features
• DIN Rail or Chassis mount by removing DIN clips
UL 508 Listed
IND. CONT.
EQ.E6I379
• Rugged, encapsulated design to resist environment
• IP20 protection
• Wide 20 to 72 Vdc input range
• M3 screw clamp terminations
• Simple snap-on for DIN Rail TS35/7.5 or TS35/15
• Galvanic isolation
• 5 year warranty
Options and Accessories
•SCP-MDC – Pair of metal DIN clips
•SCP-PDC – 1 plastic DIN clip with lever for
removal from rail
Standards
•
•
•
•
UL60950, E137632
EN60950
CE and IP20
UL 508 Listed
UL 60950
E137632
CUL/CSAC22.2
No. 234-M90
EMC and
Low Volt.
Directive
Applications
These units regulate voltage for sensitive electronic equipment run from battery power. For example, a 24 Vdc battery
system where the battery voltage can be 30 volts, sometimes higher during charging, and dip below 22 volts under
heavy load. The SCD can be used to stabilize the voltage for
those devices not designed to handle wider voltage swings.
They are also a convenient and inexpensive alternative to
running AC power through a large industrial machine. The
SCD can use 24 Vdc commonly available on many parts
of the machine to create other voltages needed to run
sensors, transducers and other devices that the machine
requires to work properly.
• Industrial
- Encoders, special sensors, communications
and instrumentation
• Telecommunications systems
• Remote Site/Harsh Environment
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SCD Series, Encapsulated, Industrial DC to DC Converter
Selection Table
Specifications
Output Voltages
Low Profile
Catalog Number
Description
V1
Vdc
Min
Load
V1 A
V2
A
Vdc
A
30 Watts; Switching DC Power Supply
Parameter
Condition
Value
Input
Input Voltage
20…72 Vdc
Filtering EMI/RFI
EN 55011/B, 55022/B
Typ. 100 kHz
Switching Frequency
SCD 30S5-DN
5V
5
5
-
-
0
SCD 30S12-DN
12 V
12
2.5
-
-
0
SCD 30S15-DN
15 V
15
2
-
-
0
SCD 30S24-DN
24 V
24
1.3
-
-
0
SCD 30S48-DN
48 V
48
0.6
-
-
0
SCD 30D15-DN
Dual O/P+15 V
15
0.8
-15
0.8
0.15
Output
Output Voltage
Accuracy
Ripple
Noise
Line Regulation
Load Regulation
Vin = 48V,
Iout = max, 25°C
V1 ≤ ±1%, V2 ≤ ±4%
Vin= min,
Iout=max, 25°C
Vin= min,
Iout= max, 25°C
Vin=min/max 25°C
Iout = max, 25°C
Iout = 10…90…10%,
25°C, Vin = 48 V, 25°C
≤2%, Vout
≤+0.5%, Vout
≤+0.5%, Vout
105…130% Inom
Overcurrent Protection
Dimensions
≤1%, Vout
Load Regulation Timing
10...90...10%, 25°C
<4 ms
Temperature Coefficient
TA = -25...+65°C
0.01%/K
Continuous
Overload/Short Circuit
Derating Single/Dual/
Triple
TA >50°C
Holdup Time
Vin = 48 V
5%/K max
General
-25…+65°C
Operating Temperature
Storage Temperature
TA = 25°C
Case Temperature Rise at
Full Load
MTBF at 25°C
(input/output)
>10 ms
45...+85°C
45 K max
acc. MIL-STD-217F
800,000 hrs
Transient Protection
EN61000-4-2, 3, 4, 5
Cooling
Convection
Weight - lbs (kg)
0.86 lbs (.39 kg)
Case Material/Potting
UL94-VO
CSA Power Supply Class
Level 3
Protection
IP20
Note: No input protection against reverse voltage.
Pin-Out
SCD 30
1
2
Single
+V1
-V1
Dual
V1
COM
3
V2
6
7
+IN
-IN
+IN
-IN
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDU Series, Direct Current Uninterruptible Power Supply (DC UPS) System
The SDU DIN Rail DC UPS is an advanced 24 Vdc
uninterruptible power system that combines an industry
leading design with a wide operational temperature range
and unique installation options. The SDU DC UPS is a
powerful, microprocessor controlled UPS that provides
protection from power interruptions. With an input voltage
range of 22.5 to 30.0 Vdc, the DC UPS is the ideal power
back-up solution for your critical connected loads.
These units were designed specifically for use with SolaHD’s
popular SDN Series of power supplies. SolaHD’s external
battery module is the only one on the market that allows you
to seal the electronics in the panel and maintain safety by
placing the battery outside of a non-ventilated enclosure.
These units include easy to wire screw terminations for
critical devices needing battery back-up. The SDU DC UPS
includes an automatic self-test feature that checks the UPS
and battery functions. Battery charging occurs automatically
when input DC power is applied. When power fails, the DC
UPS will switch to battery back-up. If the battery is no longer
useful, the UPS will sound an alarm and an LED indicator will
illuminate.
Back-up power protection in modern industrial applications
depends mainly on AC UPS. AC is converted to DC, and
converted back to AC in the AC UPS, then converted back
to DC in the protected equipment power supply. By applying
the new SolaHD SDU DIN Rail DC UPS, you avoid the
inefficiencies of all these conversions. This design maximizes
system up-time flexibility, and optimizes reliability assurance.
Applications
•
•
•
•
•
•
•
•
Industrial/Machine Control
Automation process Control
Computer-based Control Systems
Conveying Equipment
Material Handling
Packaging Machines
Semiconductor Fabrication Equipment
DeviceNetTM
• Amusement Park Equipment
• Pharmaceutical Applications
• Control Rooms
IND. CONT.
EQ
E137632
I.T.E.
Features
• Modular, rugged industrial grade design
• Microprocessor based controls
• Automatic self-test feature for UPS function and battery
management check
• Power module wide operation temperature
range (-20° to +50°C)
• Flexible batteries back-up expansion capabilities
• Overload protection in normal and battery modes
• User replaceable batteries
• IP20 rated input and output screw terminals
• No internal fan, no extra cooling required
• Sturdy, reliable all metal DIN Rail mounting
connector
• LED Status Indicators
• Universal Dry Contact Relay terminals provide
remote signaling
• Monitoring, diagnostics, and remote turn-on and
shut-off capabilities
• Two year warranty
Related Products
• SDN-P Series DIN Rail Power Supplies
• SDN-C Series DIN Rail Power Supplies
• STV 25K Series Surge Protective Devices
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Selection Table
Catalog Number
Description
Approx. Ship Weight lbs (kg)
SDU 10-24
240 VA, 24V/10A DIN Rail DC UPS power module, battery module is required
1.65 (0.65)
SDU 20-24
480 VA, 24V/20A DIN Rail DC UPS power module, battery module is required
1.65 (0.65)
SDU 24-BAT
24V DIN Rail/Panel Mount Battery Module (cable included)
12.0 (5.33)
SDU 24-BATEM
24V External Mount Battery Module (cable included)
16.0 (7.11)
SDU 24EXTBC6
Optional 6 ft. Battery Module cable to 24V DC UPS
0.5 (0.22)
SDU 24-DB9
Optional interface kit to convert relay contacts signals to DB9 signals
1.0 (0.45)
SDU-PMBRK
Optional chassis mount brackets to secure UPS to wall, panel, or enclosure
0.5 0(.22)
There are three individual hardware products when putting
an SDU DC UPS system into operation:
1.24 Vdc Power Supply (Recommended SolaHD
SDN Series)
2.24 Vdc SDU DC UPS Power Module
3.24 Vdc SDU DC UPS Battery Module; or
24 Vdc SDU DC UPS External Battery Module
There are two models of the SDU DC UPS Power Module:
1.SDU 10-24, 24 Vdc/10amp (battery modules are
required)
2.SDU 20-24, 24 Vdc/20amp (battery modules
are required)
There are two models* of the SDU DC UPS Battery Modules:
1.SDU 24-BAT, DIN Rail/Panel mount for installation in
ventilated enclosure, up to 4 battery modules can be
connected to the SDU DC UPS.
2.SDU 24-BATEM, Panel mount, alternate battery module
for external installation of non-ventilated enclosures, only
1 battery module can be connected to the SDU DC UPS.
*Can not use a combination of both models of the battery modules, only
one model of the battery module can be connected to the SDU DC UPS.
DIN Rail Mounted Battery Option
External Battery Option
Notes:
Notes:
1) AC/DC Power Supply
1) AC/DC Power Supply
2) Power Module: SDU 10-24 or SDU 20-24
2) Power Module: SDU 10-24 or SDU 20-24
3) Battery Module: SDU 24-BAT
3) Battery Module: SDU 24-BATEM
4) Optional battery module for extended runtime.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDU DC UPS Power Modules Specifications
Specification
SDU 10-24
SDU 20-24
Input
24 Vdc
Nominal Input Voltage
22.5 - 30 Vdc
Input Voltage Range
DC Fuse 30A
Input Fuse
Output
24 Vdc
Nominal Output Voltage
22.5 - 30 Vdc
Output Voltage Range
Output Current
10A
20A
Current Limit
12A
22A
Input Protection
Protection
Fuse for overload & short circuit protection
Electrical Circuit Protection
Overload Protection
UPS output cut off immediately
Short Circuit
Type
Charging Current
Typical Recharge
Time (to 90% of full capacity)
Back-up Time (full load)1
Protection
Battery Module
Sealed, maintenance-free lead acid batteries.
0.5 A
8 Hours for 1 Battery Module
24 Hours for 2 Battery Module
12 Hours for each additional Battery Module
14 min.
4 min.
UPS Shutdown when battery voltage drops below 22V, to prevent the complete depletion of the battery,
short circuit protection by a 30A fuse.
Physical
Net Weight - lbs (kg)
Dimensions H x W x D - in. (mm)
Battery Low
Overload
Audible Noise
1.65 (0.75)
4.88 x 3.02 x 4.55 (124 x 77 x 116)
Alarm
Rapid Audible Indicator every 1 second
Continuous Audible Indicator
Environment
<40 dBA (1 meter from surface)
Power Module Operating Temperature
-20oC to +50oC
Storage Temperature
-20oC to +70oC
Humidity
Max Elevation
Shock & Vibration
US Standard
Canadian Standard
CE
MTBF
Output
Mounting
Connections
Relay Contact Terminal Connections
Case
Free Space
0-95%
3500 meters (11,483 feet)
According to ISTA 2A
DC UPS System2 Safety
UL 60950-1, UL508, FCC Part 15, Class A
CAN/CSA C22.2 No 107.1-01, CAN/CSA C22.2 No. 60950-1
Low Voltage Directive IEC 60950-1 (CB Scheme)
Directive 2004/108/EC: EN 62040-2 Category C2 EN 55022 Class A + A1 + A2, CISPR 22 Class A (2005), IEC 61000-32, IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6 + A1, IEC 61000-4-8, IEC 61000-2-2
General
> 200,000 Hours, MIL-STD HDBK-217F
Installation
Outputs are capable of providing high currents for short periods of time for inductive load startup or switching.
Fusing may be required for wire/loads if 2x Nominal O/P current rating cannot be tolerated.
Continuous current overload allows for reliable fuse tripping
Simple snap-on system for DIN Rail TS35/7.5 or TS35/15 or chassis-mounted, optional screw mounting set SDU-PMBRK.
Input & Output: IP20-rated screw terminals, connector size range: 16-12 AWG (0.5-4 mm2)
for copper conductors rated 90o.
IP20 screw terminals; connector size range: 24-16 AWG (0.34-4mm2)
Fully enclosed metal housing with ventilation grid to keep out small particles.
20 mm above and 35 mm below, 20 mm left and right, 10 mm in front
Notes:
1. See Battery Back-Up Times on next page.
2. DC UPS System includes one power module (SDU 10-24 or SDU 20-24) and one or more battery modules (SDU 24-BAT or SDU 24BATEM)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SDU DC UPS Back-Up Times (Typical)
SDN DC UPS Battery Module Specifications
Parameter
SDU 24-BAT
24 Vdc
Nominal Voltage
Fuse: 30A
Circuit Breaker: 24V, 25A
0.5A
0.8A
4.88 x 8.27 x 4.55
(124 x 210 x 116)
11.5 x 5.57 x 4.57
(292 x 142 x 116)
Enclosure Type
IP20
NEMA 1
Terminal Connector
Type
Polarized Powerpole Connectors
Protection
Charging Current
Enclosure
Dimension in. (mm)
Batteries
Accessories
Operating
Temperature
Storage
Temperature
Humidity
Safety Standard For
DC UPS System*
Weight - lbs (kg)
Mounting
SDU 10-24 with SDU 24-BAT
SDU 24-BATEM
Replaceable Batteries
1 ft. polarized
6 ft. polarized
battery cable
battery cable
-20o to +50oC
-20o to +40oC
95% no condensation
UL60950-1, IEC 60950-1, UL508, CE
CAN/CSA C22.2 No 107.1-01
CAN/CSA C22.2 No 60950-1
12 (5.33)
16 (7.11)
Simple snap-on system
for DIN Rail TS35/7.5
or TS35/15 or chassismounted, optional
screw mounting set
SDU-PMBRK.
Load
20% (2A)
40% (4A)
60% (6A)
80% (8A)
100% (10A)
1 unit
2 units
113
45
30
21
14
247
114
74
48
38
3 units
396
178
117
80
58
4 units
531
233
148
111
81
1 EBP
135
19
14
SDU 10-24 with SDU 24-BATEM
52
28
SDU 20-24 with SDU 24-BAT
Load
20% (4A)
40% (8A)
60% (12A)
80% (16A)
100% (20A)
1 unit
46
21
10
06
04
2 units
116
50
28
17
10
3 units
178
80
46
31
20
4 units
237
113
65
43
31
1 EBP
48
6
4
SDU 20-24 with SDU 24-BATEM
17
9
Wall/Chassis Mounting
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SFL Series, 75–600 Watt
The SFL series is a DIN Rail switching power supply series
that complements the SolaHD SDN™ products with more
input voltage, output voltage and power levels to give an
even broader range of industrial DC power solutions.
These products are available in 12, 24 and 48 Vdc output
and 115/230 Vac Input. They feature pluggable screw
connectors* (mating connectors are included in each box
sold) for easy installation and service. The products feature
a DIN Rail connection, front panel DC OK indicators, and
easily accessible AC and DC connections.
For parallel operation with power sharing, a redundant
version is available for the 300 W (24 V/12 A) and 600 W
(24 V/24 A) models.
UL 508 Listed
IND. CONT.
EQ.E6I379
Features
UL 60950
E137632
CUL/CSA-C22.2
No. 234-M90
EMC and
Low Volt.
Directive
• DIN Rail Mount regulated switch mode power supplies
• 12 V, 24 V, and 48 V outputs available from 1.5-24 A
• Easy-to-wire pluggable* and screw terminal connectors
• Fully Integrated Redundant models available:
- RED (For SFL24-24-100 and SFL12-24-100 only)
Designed for N + 1 redundant power supply systems,
these units provide active current sharing and allow
up to 5 power supplies to be paralleled. Decoupling
diodes and an alarm output to signal a unit failure
are included in this option. Multiple units are required
for redundancy.
• Adjustable output voltage
• Selectable input: 115/230 Vac
• UL1604 Listed for Class 1, Division 2 hazardous
locations (except -RED and -UDS versions)
• UL 508 Listed (except -RED and -UDS versions).
No derating necessary.
• Two year warranty
• Models with optional battery back-up available:
- UDS (For SFL24-24-100 and SFL12-24-100 only)
Contact Technical Services for details.
* Except 600 watt models.
Selection Table
Catalog Number
Input Voltage Selectable
SFL 6-12-100
SFL 1.5-48-100
SFL 3-48-100
SFL 12-24-100
SFL 6-48-100
115/230 Vac
SFL 24-24-100
SFL 12-48-100
Output Power Maximum
Output Voltage Nominal
Output Current Maximum
75 Watt
12 Vdc
48 Vdc
6A
1.5 A
150 Watt
48 Vdc
3A
300 Watt
24 Vdc
48 Vdc
12 A
6A
600 Watt
24 Vdc
48 Vdc
24 A
12 A
24 Vdc
12 A
24 A
Redundant Models
SFL 12-24-100RED
SFL 24-24-100RED
115/230 Vac
300 Watt
600 Watt
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SFL Specifications
Parameter
Value
Parameter
Input
Input voltages nominal (user selectable)
General
93-132 Vac / 187-264 Vac
47-63 Hz
Input Frequency
Input current at full load (typical)
- 75 W (12 V/6 A, 24 V/3 A, 48 V/1.5 A)
- 150 W (24 V/6 A, 48 V/3 A)
- 300 W (24 V/12 A, 48 V/6 A)
- 600 W (24 V/24 A, 48 V/12 A)
Inrush current (max.)
- 75 W
- 150 W
- 300 W
- 600 W
Internal fuse (slow blow) not accessible
- 75 W / 150 W
- 300 W
- 600 W
115 Vac
1.7A
3.0A
5.4A
10.5A
115 Vac
16.5 A
35.0 A
35.0 A
70.0 A
230 Vac
0.9 A
1.7 A
3.3 A
6.4 A
230 Vac
33.0 A
70.0 A
70.0 A
80.0 A
4.0 A
6.3 A
12.0 A
Output
Voltage Adjustment Range
- 12 V models
- 24 V models
- 48 V models
Output Regulation
- Line voltage variation
- Load variation 10–90%
75W, 150W models
300W, 600W models
Ripple and noise (20 MHz bandwidth)
Electronic short circuit protection /
current limitation
Parallel Operation
- SFL12-24-100RED
- SFL24-24-100RED
Overvoltage Protection,
trigger point at
Holdup Time
Value
Operating Temperature Range
Derating above 50°C
Storage Temperature
Humidity (non condensing)
Switching Frequency
- 75 W
- 150 W/300 W/600 W
±0.2% max.
±1.0% max.
±0.5% max.
< 50 mVpp
110 % typ. (constant current)
Up to 5 units
Operation Indication
Isolation Voltage
- Input/output
- Input/case
- Output/case
95% rel H max.
100 kHz typical
67 kHz typical
>85%
LED, DC OK
3,000 Vac (1 minute)
2,000 Vac (1 minute)
500 Vac (1 minute)
Class 1
Safety Class (IEC536)
Conducted EMI according to:
Electromagnetic Susceptibility
- Electrostatic discharge ESD.
- RF field susceptibility.
- Electrical fast transients/
bursts on main line.
- Immunity to conducted radio
frequency disturbances above
9 kHz.
- Mains frequency field
Case protection according to IEC529
Case material
Mounting
140% typical out nominal
-25°C...+85°C
Efficiency
Safety Standards Met
12 – 14 Vdc
24 – 28 Vdc
48 – 52 Vdc
-25°C...+70°C 2%/°C
IEC950,EN60950,CE marked
for LVD, UL60950 recognized
and UL 508.
EN55022 Class B, EN55011
Class B, FCC-B
EN61000-4-2
EN61000-4-3
EN61000-4-4
4 kV/8 kV
10 V/m
2 kV
EN61000-4-6
10 V
EN61000-4-8
30 A/m
IP 20
Steel
Snap-on 35 mm DIN Rail as
per EN50022 or Chassis mounting
option available
min. 20 mS
Mounting Brackets
For easy conversion to panel or chassis mounting.
Catalog Number
SFL 75-PMBRK
SFL 150-PMBRK
SFL 300-PMBRK
SFL 600-PMBRK
Output Power Maximum
75 Watt
150 Watt
300 Watt
600 Watt
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SFL Series Dimensions (inches/mm)
SFL 75 Watt (12 V/6 A, 48 V/1.5 A)
SFL 150 Watt (SFL 3-48-100)
SOLA
SFL 6-12-100
Clip for
35 mm DIN-rail
LED
4.51 (114.6)
SOLA
LED
SFL3-48-100
4.51 (114.6)
2.25
(57.3)
2.25 (57.3)
1.77
(45)
3.54
(90)
2.23
(56.7)
.27 (7)
2.23
(56.7)
6.18 (157)
1.51
(38.5)
3.14 (80)
.27 (7)
50V
2.23 (56.7)
Weight: 1.06 lbs/.48 kg approx.
Weight: 1.6 lbs/.73 kg approx.
SFL 300 Watt (SFL 12-24-100[RED], SFL 6-48-100)
S O LA
SFL 12-24-100
4.51 (114.6)
50V
2.23 (56.7)
SFL 600 Watt (SFL 12-48-100, SFL 24-24-100[RED])
Vout
adi
NP
LED
S O LA
2.25
(57.3)
3.25
(82.6)
1.06
(27.1)
LED
.60 (15.3)
2.24
(57.0)
SFL 24-24-100
6.97 (177.2)
1.51
(38.5)
5.11 (130)
.13
(3.4)
3.26
(83)
8.14 (207)
6.97 (177.2)
.27 (7)
50V
9.56 (243)
1.83
(46.5)
3.26 (83)
Weight: 3.09 lbs/1.4 kg approx.
5.90 (150)
.27 (7)
3.25 (82.8)
Weight: 4 lbs/1.81 kg approx.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Silver Line Series – Single & Multi-Output Linears
Specifications
Parameter
Condition
Limit
Input
100/120/220/230/240
Vac Selectable
Input Voltage
47-63 Hz
Input Frequency
Output
Line Regulation
for 10% change
Load Regulation
for 50% change
LVD
The Silver Line series follows the industry accepted
footprint for open frame, linear power supplies. Standard
screw terminal connections and optional covers are offered
for safety considerations.
Features
• Easy-to-install screw terminal connections
DC Output
Adjustment Range
• Universal input and approvals (115/230 Vac)
• Low noise, extremely quiet DC output. For noise
sensitive or analog circuitry.
• Fast transient response. Ideal for test applications.
All 5-Volt outputs include
build-in OVP as standard
(setting is 6.2 V ±0.4 V)
OVP is optionally
available on other types
at 50% Load Changes
Remote Sensing
50 msec.
Automatic current
limit foldback
Overload
Protection
• Cover options
• Industry standard footprint
±5% Minimum
Overvoltage
Protection
Transient
Response Time
0.05%
3.0 mV maximum
Peak-to-Peak
Ripple
UL 60950
E137632
0.05%
Available to compensate
for output voltage drop
on selected models.
0.5 Vdc
General
Operating
Temperature Range
Derate to 40% at +70°C
0 to +50°C
Storage
Temperature Range
-25°C to +85°C
Temperature
Coefficient (Typical)
0.01% 0°C
After warm-up
±.5%
• Built-in OVP on 5 V models and optional on
12, 15 and 24 V models
Stability
• Automatic resetting overload protection
EMI/RFI
Linear power supplies
have inherently low
conducted and radiate
noise levels
Cover Option
Derate power by an additional 15%
Cooling
Forced air. 20 CFM required for full rating
Derate 30% without cooling
• Short circuit protected
• Two year warranty
Applications
• Industrial Control Circuits and Components
For most system
applications they will
meet requirements of
FCC Class B and VDE
0871 for Class B
Specifications are typical. Load Regulation on outputs without Remote
Sense, .1% typical.
• Instrumentation
• Drives
• CNC Machinery
• Equipment for food industry
• Microprocessor circuits
• Analog Circuits
• Noise sensitive Circuitry and Sensors
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SL Series Selection Table
Catalog Number
Output 1
Dimensions - inches (mm)
Output 2
Output 3
SLS-05-030-1T
5 V @ 3 A*#
–
–
Case
A
SLS-05-060-1T
5 V @ 6 A*#
–
–
B1
SLS-05-090-1T
5 V @ 9 A*#
–
–
C
SLS-05-120-1T
5 V @ 12 A*#
–
–
I2
SLS-12-017T1
12 V @ 1.7 A# or
15 V @ 1.5 A
–
–
A
SLS-12-034T
12 V @ 3.4 A#
–
–
B1
SLS-12-051T
12 V @ 5.1 A#
–
–
C
SLS-12-068T
12 V @ 6.8 A#
–
–
I2
SLS-15-045T
15 V @ 4.5 A#
–
–
C
SLS-15-060T
15 V @ 6 A#
–
–
I2
SLS-24-012T
24 V @ 1.2 A#
–
–
A
SLS-24-024T
24 V @ 2.4 A#
–
–
B2
SLS-24-036T
24 V @ 3.6 A#
–
–
C
SLS-24-048T
24 V @ 4.8 A#
–
–
I2
SLS-24-072T
24 V @ 7.2 A#
–
–
K
SLS-24-120T
24 V @ 12.0 A#
–
–
L
SLD-12-1010-12T1
12 V @ 1 A or
15 V @ .8 A
-12 V @ 1 A or
-15 V @ .8
–
H1
SLD-12-1818-12T1
12 V @ 1.8 A or
15 V @ 1.5 A
-12 V @ 1.8 A or
-15 V @ 1.5 A
–
D
SLD-12-3434-12T
12 V @ 3.4 A#
-12 V @ 3.4 A#
–
I3
SLD-15-3030-15T
15 V @ 3 A#
-15 V @ 3 A#
–
I3
SLD-12-6034-05T
5 V @ 6 A*#
12 V @ 3.4 A#
–
I1
SLD-12-3015-05T
5 V @ 3 A*#
12 V@ 1.5 A
–
C1
5 V @ 2 A*#
12 V @ .4 A or
15 V @ .4 A
-12 V @ .4 A or
-15 V @ .4 A
H2
SLT 12-31010-12T1
5 V @ 3 A*#
12 V @ 1 A# or
15 V @ .8 A
-12 V @ 1 A# or
-15 V @ .8 A
F
SLT 12-61818-12T1
5V @ 6A*#
12 V @1.8 A or
15 V @1.5 A
-12 V @ 1.8
A or -15 V @
1.5 A
G2
SLO-12-000-1
6.2 V to 34 V
Adjustable @ 8 A
For Cases B through K
J1
SLO-12-000-TB
6.2 V to 34 V
Adjustable @ 8 A
For Case A or Cases B through K
(when used with a cover)
J2
SLT 12-20404-12T
1
Case A
Over Voltage Protector (OVP)
Notes:
*
With Built-In OVP
#
With Remote Sense (R.S.)
1. 12/15 Volt models are factory set for 12 Volt operation. 15 Volt operation
is field adjustable.
Case B
Cover Options
Catalog
Number
Description
Catalog
Number
Description
SLCASA-CVR
Cover for Case A
SLCASG-CVR
Cover for Case G2
SLCASB-CVR
Cover for Case B
SLCASH-CVR
Cover for Cases H1 & H2
SLCASC-CVR
Cover for Case C
SLCASI-CVR
Cover for Cases
I1, I2, & I3
SLCASC1-CVR
Cover for Case C1
SLCASK-CVR
Cover for Case K
SLCASD-CVR
Cover for Case D
SLCASL-CVR
Cover for Case L
SLCASF-CVR
Cover for Case F
Note:
Covers are sold separately. When used, derate the power supply by 15%
of its rated value.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Silver Line Dimensions (inches/mm)
Case F
Cases C and C1
Case G2
Case D
AC Input Jumper Connections
For use at:
100 Vac
120 Vac
220 Vac
230/240 Vac
Connect:
1-3, 2-4
1-3, 2-4
2-3
2-3
Apply AC:
1&5
1&4
1&5
1&4
Cases H1 and H2
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Silver Line Dimensions (inches/mm)
Case J1
Case J2
/60 /04)/.!,
!# ).054$# /54054
Cases I1, I2 and I3
-!8
6 !$*
All dimensions in inches (mm). Dimensions may change and should not be
used for construction purposes.
/54
Notes:
/54
3
3
² -4' (/,%3 0,!#%3
!# )NPUT
7%)'(4 ,"3
+'
0%- .54 (/,%3
-4' 0,!#%3
Be sure to specify the complete part number when ordering. Orders may be
placed with your local SolaHD distributor.
Case K
7%)'(4 ,"3
+'
!# ).054$# /54054
v v 6 !$*
/60 /04)/.!,
v
² -4' (/,%3 0,!#%3
/54
3
3
/54
-A X
!# )NPUT
(EAT 3INK
v Case L
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Linear OEM – Single Output
Applications
• Microprocessor Circuits
• Instrumentation
• Process Controls
• CNC Machinery
• Control Circuits
• Analog Circuits
• Noise sensitive Circuits
Specifications
Parameter
Condition
Limit
Input
104-127 Vac
208-254 Vac
Input Voltage
50-60 Hz
Input Frequency
Output
UL 601950-1
E137632
Features
• Low noise output
• 115/230 Vac input
Regulation Line & Load
±0.1%
Pard (Ripple and Noise)
0.1% pk/pk
Periodic Deviations
(Ripple)
10mv rms
Output Voltage
Adjustment
±5% Minimum
Transient
Recovery Time
• Remote sensing
50%-100% Load
Less than 50 msec
General
• Designed for both bench and rack use
• Completely protected short circuit proof; automatic
foldback.
Storage Ambient Temp.
-40°C to +85°C
Operating Ambient Temp.
0°C to +50°C
• Current limiting – automatic reset
Temp. Effect Coefficient
0.03% °C
• Isolated floating output
Polarity
• UL Recognized, CSA Certified
Short Circuit Protection
• Built-in OVP on 5 Volt models
• Terminal block on Case D models (24 V/6 A)
• One year warranty
Selection Table
Maximum Allowable
Lead Drop for Remote
Sensing
5%
Maximum Output Current
120% Rated Current
Maximum Short Circuit
Current
30% Rated Current
Input/Output Isolation
Catalog Number
Output 1
Case
83-05-230-3
5 V @ 3.0 A
B
83-12-218-3
12 V @ 1.8 A
B
83-24-212-3
24 V @ 1.2 A
B
83-24-225-3
24 V @ 2.5 A
C
83-05-312-3
5 V @ 12 A
D
83-12-310-3
12 V @ 10 A
D
83-24-260-3
24 V @ 6 A
D
May be used
positive or negative
Protected with
Automatic Recovery
Cooling
1000 Megohms D.C.,
2500 Vac
Forced air. 20 CFM required for full rating
Derate 30% without cooling
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Linear OEM Cases and Dimensions
Case D
Notes:
All dimensions in inches (mm). Dimensions may change and should not be
used for construction purposes.
Case B
When ordering, be sure to specify the complete part number. Orders may
be placed with your local SolaHD distributor.
Case C
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
GL Series: Single & Multi Output Switchers
Specifications
Parameter
Condition
Limit
Input
Input Voltage
85 to 264 Vac
Input Frequency
47 to 63 Hz
Line Fuse on board
Protection
Inrush Current
Cold Start
15 to 60 A Max
Line Regulation
Full Rated Load
±0.5%
Load Regulation
Full Rated Load
±1% Single Output
±2% Main Output
Output
200 Watt model
40, 65, 100 Watt models
UL 6950
E137632
EN 60950
These compact, low profile, AC/DC switching power
supplies offer universal input voltage with no switches or
jumpers, ideal for higher volume worldwide applications.
40 watt through 110 watt are printed circuit board design
with pin and socket connections, 200 watt models are
enclosed with internal DC brushless fan and screw terminal
connections.
Features
Cross Regulation
Full Rated Load
5% Typical
Minimum Loading
Main Output
10%
Temp. Coefficient
±0.04%/ °C
Hold up Time
10 mS min.
Overvoltage
Protection
112 to 132%
of Nominal
#1 Output
2% peak to peak max.
Output Ripple
General
Operating
Temperature
Full Rated Load
-0 to 50°C
Storage
Temperature
• Universal input
-20 to +85°C
• Compact size
Efficiency
Full Rated Load
65% min.
• Industry standard size (3 x 5”, 40 Watt)
MTBF
Per MIL-HDBK-217E
100,000 hour
• On board input fuse
Shock & Vibration
• Automatic overload protection
Safety
• OVP on Output #1
Cooling
Designed to meet
MIL-STD 810C
UL 60950, CSA C22.2
No. 234, EN 60950
All Models
30% Rated Current
• UL Recognized, CSA Certified, CE, LVD, TUV
• 100% Burn-In
Connector Kits
• Power fail signal on 110 and 200 Watt model
• 200 Watt enclosed with screw terminals
• One year warranty
Applications
• Industrial computers
• Drive circuits
• Control
• CNC machinery
• Instrumentation
• Printers
• Scanners
• Peripherals
Applicable
Models
Input/Output
Mating Connector
Signal
Connector
GL40-KIT
40 Watt
X
N/A
GL65-KIT
65 Watt
X
N/A
GL110-KIT
110 Watt
X
N/A
GL200-KIT
200 Watt
N/A
X
Catalog Number
Auxiliary Signal Connector - 200 watt units only
Model
All 200 Watt Models
Pin 1
Fan
Pin 2
Common
Pin 3
Common
Pin 4
Power Fail
Mating Connector Kits
•Can be ordered separately for units with Molex
connection (40, 65 and 110 watt units only).
•Kits include mating housing and pins for input and
output connection.
Auxiliary Mating Connector Kit for 200 watt units
Kit is for auxiliary signal connection only. Not required for
input and output connection which are screw terminal.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Output 1
Output 2
Output 3
Maximum
Output
GLS-01-040
5 V, 6A
-
-
30 W
GLS-02-040
12 V, 3.5 A
-
-
40 W
GLS-03-040
15 V, 3A
-
-
40 W
GLS-04-040
24 V, 2 A
-
-
40 W
GLD-01-040
5 V, 3 A
12 V, 2 A
-
40 W
GLD-02-040
5 V, 3 A
15 V, 2 A
-
40 W
GLD-03-040
5 V, 3 A
24 V, 1 A
-
40 W
GLT-01-040
5 V, 3 A
12 V, 2 A
-5 V, 0.3 A
40 W
GLT-02-040
5 V, 3 A
12 V, 2 A
-12 V, 0.3 A
40 W
GLT-03-040
5 V, 3 A
15 V, 2 A
-15 V, 0.3 A
40 W
GLT-04-040
5 V, 3 A
15 V, 2 A
-12 V, 0.3 A
40 W
GLT-05-040
5 V, 3 A
24 V, 1 A
-12 V, 0.3 A
40 W
0.157 (4.0) MOUNTING HOLE (4 PL)
1
DC
OUTPUT
AC
INPUT
P1
N
6
3.00 (76.2)
Catalog
Number
Dimensions for 40 Watt, GL Series
2.55 (64.8)
Selection Table for 40 Watt, GL Series
L
0.20 (5.0)
0.20 (5.0)
4.55 (115.6)
5.00 (127.0)
1.18 (30.0) 1.36 (34.5)
Notes:
1. Tolerance 0.02/0.5 maximum.
Output Connector
Model
2. Input connector Molex # 09-50-3031 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
Pin 1
Pint 2
Pin 3
Pin 4
Pin 5
Pin 6
GLS
Output 1
Output 1
Output 1
Return
Return
Return
3. Output connector Molex# 09-50-3061 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
GLD
Output 2
Output 1
Output 1
Common
Common
N/A
4. Weight: 10.6 oz. (300 grams) approx.
GLT
Output 2
Output 1
Output 1
Common
Common
Output 3
5. Input/Output Mating Connector kit available. Catalog number GL40-KIT.
6. All dimensions in inches (mm).
Dimensions for 65 Watt, GL Series
Output 3
Output 4
Maximum
Output
GLS-01-065
5 V, 10 A
-
-
-
50 W
GLS-02-065
12 V, 5.5 A
-
-
-
65 W
GLS-03-065
15 V, 4.5 A
-
-
-
65 W
GLS-04-065
24 V, 3 A
-
-
-
65 W
GLD-01-065
5 V, 6 A
12 V, 3 A
-
-
65 W
5 V, 6 A
15 V, 3 A
GLD-03-065
5 V, 6 A
24 V, 2 A
-
-
65 W
GLT-01-065
5 V, 6 A
12 V, 3 A
-5 V, 0.3 A
-
65 W
GLD-02-065
GLT-02-065
5 V, 6 A
12 V, 3 A
GLT-03-065
5 V, 6 A
15 V, 3 A
-
-
-12 V, 0.5 A
-15 V, 0.5 A
-12 V, 0.5 A
L
65 W
-
65 W
-
65 W
GLT-04-065
5 V, 6 A
15 V, 3 A
-
65 W
GLT-05-065
5 V, 6 A
24 V, 2 A
-12 V, 0.5 A
-
65 W
GLQ-01-065
5 V, 6 A
12 V, 3 A
-12 V, 0.5 A
-5 V, 0.5 A
65 W
N
P1
AC
INPUT
8
DC
OUTPUT
P2
1
0.59 (15.0)
4.80 (122.0)
6.00 (152.6)
1.77 (45.0)
Notes:
Output Connector
Model
0.157 (4.0) DIA. MOUNTING HOLD (4PL)
0.10 (2.5)
Output 2
3.15 (80.0)
Output 1
0.18 (4.5)
Catalog
Number
3.50 (89.0)
Selection Table for 65 Watt, GL Series
Pin 1
Pint 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
GLS
Output 1
Output 1
Output 1
Output 1
Return
Return
Return
Return
GLD
Output 1
Output 1
Common
Common
Output 2
Output 2
N/A
N/A
GLT
Output 1
Output 1
Common
Common
Output 2
Output 2
Output 3
N/A
GLQ
Output 1
Output 1
Common
Common
Output 2
Output 2
Output 3
Output 4
1.
Tolerance 0.02/0.5 maximum.
2.
Input connector Molex # 09-50-3031 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
3.
Output connector Molex # 09-50-3081 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
4.
Weight: 13.4 oz. (380 grams) approx.
5.
Input/Output Mating Connector kit available. Catalog number GL65-KIT.
6.
All dimensions in inches (mm).
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Power Supplies
Selection Table for 110 Watt, GL Series
Dimensions for 110 Watt, GL Series
Catalog
Number
Output 1
Output 2
Output 3
Output 4
GLS-01-110
5 V, 22 A
-
-
-
Maximum
Output
110 W
GLS-02-110
12 V, 9 A
-
-
-
110 W
GLS-03-110
15 V, 7.5 A
-
-
-
110 W
GLS-04-110
24 V, 4.5 A
-
-
-
110 W
GLD-01-110
5 V, 10 A
12 V, 5 A
-12 V, 1 A
-
110 W
GLT-01-110
5 V, 10 A
15 V, 4 A
-15 V, 1 A
-
110 W
GLT-02-110
5 V, 10 A
24 V, 1 A
-15 V, 1 A
-
110 W
GLQ-01-110
5 V, 10 A
12 V, 5 A
-12 V, 1 A
-5 V, 1 A
110 W
GLQ-02-110
5 V, 10 A
12 V, 5 A
-12 V, 1 A
+12 V, 1 A
110 W
GLQ-03-110
5 V, 10 A
12 V, 5 A
-12 V, 1 A
+24 V, 1 A
110 W
GLQ-04-110
5 V, 10 A
15 V, 4 A
-15 V, 1 A
-5 V, 1 A
110 W
Output Connector
Model Pin 1
4
Notes:
Pint 2
Pin 3
Pin 4
Pin 5
Pin 6
GLS
Output 1
Output 1
Output 1
Return
Return
Return
GLD
Output 2
Output 1
Output 1
Common
Common
N/A
GLT
Output 2
Output 1
Output 1
Common
Common
Output 3
1. Tolerance 0.02 (0.5) maximum.
2. Input connector Molex # 09-50-3051 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
3. Output connector Molex # 09-50-3131 and Molex series 2578 #08-500105 crimp terminal using Molex # 63811-2200 hand applicator.
4. Weight: 1.32 lbs. (600 grams) approx.
5. Input/Output Mating Connector kit available.
Catalog number GL110-KIT.
6. All dimensions in inches (mm).
Selection Table for 200 Watt, GL Series
Catalog
Number
Output 1
GLS-01-200
5 V, 40 A
Dimensions for 200 Watt, GL Series
Output 2
Output 3
Output 4
Maximum
Output
-
-
-
200 W
GLS-02-200 12 V, 16.7 A
-
-
-
200 W
GLS-03-200 15 V, 13.4 A
-
-
-
200 W
GLS-04-200
24 V, 8.4 A
-
-
-
200 W
GLD-01-200
5 V, 30 A
12 V, 8 A
-
-
200 W
GLD-02-200
5 V, 30 A
15 V, 6 A
-
-
200 W
GLD-03-200
5 V, 30 A
24 V, 4 A
-
-
200 W
GLT-01-200
5 V, 30 A
12 V, 8 A
-5 V, 6 A
-
200 W
GLT-02-200
5 V, 30 A
12 V, 8 A
-12 V, 4 A
-
200 W
GLT-03-200
5 V, 30 A
15 V, 6 A
-15 V, 4 A
-
200 W
GLT-04-200
5 V, 30 A
15 V, 6 A
-12 V, 4 A
-
200 W
GLQ-01-200
5 V, 30 A
12 V, 8 A
-12 V, 4 A
5 V, 6 A
200 W
GLQ-02-200
5 V, 30 A
15 V, 6 A
-15 V, 4 A
24 V, 4 A
200 W
GLQ-03-200
5 V, 30 A
12 V, 8 A
-12 V, 4 A
12 V, 4 A
200 W
GLQ-04-200
5 V, 30 A
12 V, 8 A
-15 V, 4 A
15 V, 4 A
200 W
GLQ-05-200
5 V, 30 A
12 V, 8 A
-12 V, 4 A
24 V, 4 A
200 W
Notes:
1. Tolerance 0.02 (0.5) maximum.
2. Connector Molex # 22-01-2041 and Molex series 2759 #08-50-0113
crimp terminal using Molex # 11-01-0185 hand applicator.
Output Connector (Terminal Block)
Model
Pin 1-2
Pint 3-4-5
Pin 6
Pin 7
Pin 8
Pin 9
GLS
- Sense
Return
Output 1
Output 1
Output 1
+Sense
GLD
Output 1
Common
Output 2
N/A
N/A
N/A
4. Weight: 3.9 lbs. (1,750 grams) approx.
GLT
Output 1
Output 1
Common
Common
N/A
N/A
5. All dimensions in inches (mm).
GLQ
Output 1
Common
Common
Output 2
Output 4 Return
Output 4
3. Connectors P3 mates with Molex housing 22-01-1043 and Molex 4809
series crimp terminal.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SMP Series: Super Slim Modular Power Supplies
These medium power, modular power supplies, from 250
through 1000 watts, are capable of up to 12 independent
outputs. Modular design makes these units easy to
customize for unusual voltage and power combinations.
All units have power factor corrected inputs, an end
mounted fan for cooling and a variety of built-in signals and
controls. High reliability and a flexible design make these
an excellent choice for process control and semiconductor
fabrication applications.
Features
• Worldwide safety agency approval (UL, CSA and CE)
• 250, 350, 450, 600 & 1000 Watt Power Platforms
• Meets IEC 61000-3-2
• Power Factor Correction (0.99)
• Universal AC Input (90-264V)
• Single wire current share
• Power fail TTL signal
• Cover and End mounted fan
• Capable of up to 12 independent outputs
• Highly Accelerated Life Tested (HALT)
• Fully isolated outputs
• Thermal overload protection
• MTBF demonstrated >500,000 hours
• Two year warranty
UL 60950
E137632
Applications
• Process Control
• Semiconductor Fabrication
• Low Profile Chassis Mount
• Service Automation
Related Products
• GL Series
• SHP Series
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Specifications
Description
Catalog Number
SM2
SM3
SM4
SM6
SM9
Input
90-264 Vac, 47-63 Hz single phase
AC Input
Less than 20 A peak
Inrush Current
PFC and Harmonic
Correction
Less than 40 A peak
Compliant with EN61000-3-2.
Input Transient
and ESD, AC
Compliant with EN61000-4-2,3,4,5,6 (Level 3 minimum)
Output
Line Regulation
AC input
Less than 0.1% for line variations from 90-264 Vac. Less than 0.3% for dual and triple output modules
Load Regulation
Less than 1.0% no load to full load and full load to no load, mains. Less than 2.0% for dual and triple output modules
Cross Regulation
Less than 0.1% between single output modules. Less than 2% between dual outputs with 25% step load change on main output.
Single wire on all main outputs, droop on secondary outputs. Single wire parallel current share
Current Share
Output Adjustment
Range
±10% of nominal on all Main outputs 5 -15 volts
on U and T module Auxiliary outputs
140% nominal rating
Current Limit
Overvoltage
Protection
Minimum Load
Dynamic Response
±5% min on all outputs
OVP is standard on all Main Output Modules and
low voltage secondary outputs. 120-130% of nominal.
OVP is standard on all Main Output Modules and low
voltage secondary outputs. 115-130% of nominal.
No preload is required on any Single, Dual output module. A min 1A, max 10% preload is required on main output
of Triple and Slim-Line Dual (U) outputs in order to achieve specified regulation.
±25% load change from a steady state 75% of nominal at a rate of 1A/µsec will result in an output deviation no greater than 2% or
100 mV peak. 125 mV for outputs 4V or less. Outputs should recover to within 1% of nominal voltage within 350 µsec.
General
Efficiency
EMC
75% typical at nominal line. 24 V+ single outputs 80%
75% typical at nominal line.
Radiated and Conducted per CISPR 11 level B, CE compliant.
EN55022 Class B,
EN61000-4-2, 3, 4, 5 & 6 Level 3
Temperature
Coefficient
0.02 - 0.03%/°C
Holdup Time,
AC Input
All AC Input units will maintain regulation within specifications for a period
of not less than 16 msec for 60 Hz, (20 msec for 50 Hz) at full rated
load from nominal 115/230 line voltage.
Remote Sense
All main outputs incorporate remote sense and are able to
compensate for a total cable drop up to 0.5 Vdc.
All AC Input units will maintain regulation within
specifications for a period of not less than 16 msec
for 60 Hz, (20 msec for 50 Hz) at full rated
load from nominal 230 line voltage.
All single output, main output on triple outputs and
dual output “D” modules incorporate remote sense
and are able to compensate for a total cable drop
up to 0.5 Vdc. Dual output “G” modules do not have
remote sense.
Temperature performance curves are available. Contact Technical Services.
Cooling
Operating
Temperature
Range
0 to +70°C (full power to 50°C, derate linearly to 50% at 70°C).
Storage
Temperature
-40° to +85°C
-350 to 7,500 feet with no derating
Operating Altitude
Shock and
Vibration
Commercial transportation ratings, suitable for International Air and Ground transport
Dimensions
Mounting
HxWxD
(inches/mm)
Weight - (lbs/kg)
All platforms - two surfaces, bottom and one side
Chassis mount via threaded M4 holes on two surfaces.
1.56 x 5 x 9.5
(40 x 127 x 241)
1.56 x 5 x 10.5
(40 x 127 x 266)
1.68 x 5 x 10.5
(43 x 127 x 266)
2.5 x 5 x 11
(64 x 127 x 280)
2.5 x 7 x 11
(64 x 178 x 280)
2.3 lbs (1.04 kg), Unit
3.5 lbs (1.59 kg) Shipping
2.9 lbs (1.32 kg), Unit
4.0 lbs (1.81 kg), Shipping
3.0 lbs (1.36 kg), Unit
4.5 lbs (2.04 kg), Shipping
3.2 lbs (1.45 kg), Unit
4.8 lbs (2.18 kg), Shipping
4.4 lbs (2 kg), Unit
6.6 lbs (3 kg), Shipping
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Selection Tables
250 Watt, SM2 Series
Catalog
Number
350 Watt, SM3 Series
Output 1
Output 2
Output 3
Maximum
Output
Catalog
Number
Output 1
Output 2
Output 3
Output 4
Maximum
Output
5 V, 50 A
-
-
250 W
SM3-S3R1
5 V, 50 A
12 V, 6 A
12 V, 6 A
-
350 W
SM2-S4
12 V, 20 A
-
-
250 W
SM3-S3R2
5 V, 50 A
15 V, 5 A
15 V, 5 A
-
350 W
SM2-S5
15 V, 16.6 A
-
-
250 W
SM3-U4R1
5 V, 40 A
12 V, 6 A
12 V, 6 A
24 V, 2.5 A
350 W
SM2-S6
24 V, 10 A
-
-
250 W
SM3-U4R2
5 V, 40 A
15 V, 5 A
15 V, 5 A
24 V, 2.5 A
350 W
SM2-S7
28 V, 9 A
-
-
250 W
SM3-U2R6
5 V, 40 A
12 V, 6 A
2 V, 4A
5 V, 8 A
350 W
SM2-S9
48 V, 5 A
-
-
250 W
SM2-R2
15 V, 5 A
15 V, 5 A
-
250 W
SM2-U4
5 V, 40 A
24 V, 2.5 A
-
250 W
SM2-T1
5 V, 20 A
12 V, 4 A
12 V, 4 A
250 W
SM2-T2
5 V, 20 A
15 V, 3 A
-15 V, 0.5 A
250 W
SM2-S3
450 Watt, SM4 Series
Catalog Number
Output 1
Output 2
Output 3
Output 4
Output 5
Maximum Output
SM4-S3S3
5 V, 50 A
5 V, 50 A
-
-
-
450 W
SM4-S3S6
5 V, 50 A
24 V, 10 A
-
-
-
450 W
SM4-S6S6
24 V, 10 A
24 V, 10 A
-
-
-
450 W
SM4-U2S3
5 V, 40 A
5 V, 50 A
12 V, 4 A
-
-
450 W
SM4-T6S3
5 V, 50 A
12 V, 10 A
12 V, 4 A
5 V, 4 A
-
450 W
SM4-U4T6
5 V, 40 A
12 V, 10 A
12 V, 4 A
5 V, 4 A
24 V, 2.5 A
450 W
600 Watt, SM6 Series
Output 1
Output 2
Output 3
Output 4
Maximum Output
SM6-C3
Catalog Number
5 V, 100 A
-
-
-
600 W
SM6-C6
24 V, 21 A
-
-
-
600 W
SM6-C7
28 V, 18 A
-
-
-
600 W
SM6-C9
48 V, 10.5 A
-
-
-
600 W
SM6-B3B3
5 V, 60 A
5 V, 60 A
-
-
600 W
SM6-G3C3A4
5 V, 100 A
12 V, 10 A
12 V, 4 A
5 V, 8 A
600 W
SM6-B3A3A4A4
5 V, 60 A
12 V, 10 A
12 V, 10 A
5 V, 20 A
600 W
SM6-B3A3A5A5
5 V, 60 A
15 V, 8 A
15 V, 8 A
5 V, 20 A
600 W
SM6-A3A5A5A6
5 V, 20 A
15 V, 8 A
15 V, 8 A
24 V, 6 A
600 W
1000 Watt, SM9 Series
Output 1
Output 2
Output 3
Output 4
Output 5
Maximum Output
SM9-C6C6
Catalog Number
24 V, 42 A
-
-
-
-
1000 W
SM9-C3C3
5 V, 100 A
5 V, 100 A
-
-
-
1000 W
SM9-D1C3B4
5 V, 100 A
12 V, 25 A
12 V, 10 A
5 V, 10 A
-
1000 W
SM9-B3B4A4A6
5 V, 60 A
12 V, 25 A
12 V, 10 A
24 V, 6 A
-
1000 W
SM9-B3B5A5A6
5 V, 60 A
15 V, 20 A
15 V, 8 A
24 V, 6 A
-
1000 W
SM9-E3C3B4
5 V, 100 A
12 V, 25 A
12 V, 10 A
15 V, 2 A
-15 V, 2 A
1000 W
SM9-D3B3B4B4
5 V, 60 A
12 V, 25 A
12 V, 25 A
5 V, 10 A
24 V, 5 A
1000 W
SM9-D3B3B5B5
5 V, 60 A
15 V, 20 A
15 V, 20 A
5 V, 10 A
24 V, 5 A
1000 W
SM9-E1C3A6
5 V, 100 A
5 V, 20 A
12 V, 2 A
-12 V, 2 A
24 V, 6 A
1000 W
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Mechanical Dimensions
M3-0.5 THD
Additional Mtg. Hole if required
0.15 Max. Screw Penetration
8.30
1.50
.75
9.50
1.56
5.500
2.50
3.500
5.00
4X M4-0.7 THD
0.15 Max. Screw Penetration
1.50
5.500
Power Supply
Output Termination Area
2X M4-0.7 THD
0.15 Max. Screw Penetration
ACL
ACN
ACG
.75
Air Flow
AC Input
3 Position Terminal Block
SM2
9.30
.75
1.50
M3-0.5 THD
Additional Mtg. Hole if required
0.15 Max. Screw Penetration
10.50
1.56
6.000
2.50
5.00
3.500
4X M4-0.7 THD
0.15 Max. Screw Penetration
1.50
Power Supply
Output Termination Area
2X M4-0.7 THD
0.15 Max. Screw Penetration
6.000
ACL
ACN
ACG
.75
Air Flow
AC Input
3 Position Terminal Block
SM3
1.50
10.50
1.68
6.000
.75
3.500
Air Flow
5.00
ACL
ACN
ACG
4X M4-0.7 THD
0.15 Max. Screw Penetration
1.56
2X M4-0.7 THD
0.15 Max. Screw Penetration
AC Input
3 Position Terminal Block
Power Supply
Output Termination Area
8.000
.75
SM4
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Mechanical Dimensions - continued
.33 Max Before Adding Terminal Lugs
2X M4 x 0.7 THD 0.15 Max.
Screw Penetration
10.200
.40
M4 x 0.7 THD Output
Hardware, Typ.
1.250
Optional Output Connectors
(Consult Technical Service)
Voltage Adjust, Typ.
11.00
-
2.50
10.200
+
.40
5.00
+
-
.40
Multi Output Connector
Molex PN 39-30-1080
Air Flow
4.200
2X M4 x 0.7 THD
0.15 Max.
Screw Penetration
Logic Connector, Typ
AMP PN 102617-3
AC Input Terminal Block
Number 6 Hardware, 0.375 Centers
Optional Input Connector
SM6
.33 Max Before Adding Terminal Lugs
2X M4 x 0.7 THD
0.15 Max. Screw Penetration
9.250
.40
1.250
M4 x 0.7 THD Output
Hardware, Typ.
Optional Output Connectors
(Consult Technical Service)
Voltage Adjust, Typ.
11.00
.40
2.50
9.250
+
+
Air Flow
7.00 6.200
+
-
-
.40
Multi Output Connector
Molex PN 39-30-1080
Logic Connector, Typ
AMP PN 102617-3
2X M4 x 0.7 THD
0.15 Max. Screw Penetration
AC Input Terminal Block
Number 6 Hardware, 0.375 Centers
Optional Input Connector
SM9
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SHP Series: Heavy Duty Modular Power Supplies
These high power, modular power supplies, from 1500
through 2000 watts, are capable of up to 12 independent
outputs. Modular design makes these units easy to
customize for unusual voltage and power combinations.
All units have power factor corrected inputs, an end
mounted fan for cooling and a variety of built-in signals and
controls. High reliability and a flexible design make these
an excellent choice for process control and semiconductor
fabrication applications.
Features
• Capable of up to 12 outputs
• Single output 24 V up to 87.4 A
• IEC 801 immunity standards
• Current Share on all outputs
• End mounted fan
• Voltage adjustment on all outputs ±10%
• Overload protection on all outputs
• Power factor correction (.99 typ.)
• Margining on all outputs
• Modular Construction
• Signals
-Global and individual module inhibits/enable
• Single phase and three phase inputs
• Two year warranty
UL 60950
E137632
Specifications
Parameter
Input Voltage
Condition
Input
SH Series
S3H Series
Limit
86 to 264 Vac (1Ø)
180 to 264 (3Ø)
Frequency
47 to 440 Hz
Protection
Internally Fused
Inrush Current
40A Max
Output
Applications
• Process Controls
• Semi-conductor Fabrication
• Automated Service Equipment
Related Products
• SMP Medium Power Modular Power Supplies
• Surge Suppression
• SCD DC to DC Converters
• Active Tracking® Filters
Line Regulation
Full Rated Load
0.2% or 5mV max
Load Regulation
Full Rated Load
0.2% or 5mV max
Minimum Loading
Where indicated
±0.02%/ °C
Temp. Coefficient
Hold up Time
Full Rated Load
2-5 V 122% to 134%
Overvoltage Protection
Short-Circuit Protection
No less than 20ms
Continuous
Protected for short-circuit, auto-recovery
0.1% or 10mV RMS
Output Ripple
General
Operating Temperature
Full Rated Load
-55 to +85°C
Storage Temperature
Efficiency
-10 to 50°C
Full Rated Load
75% to 82%
MTBF
>500,000 hours
Shock & Vibration
MIL-HDBK 810E
EMI
CISPR 22, EN55022
Level B
Safety
Cooling
All Models
UL, CE and CSA
Internal DC fan 24
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
Selection Tables
Single Phase 1500 Watt, SH15 Series
Catalog
Number
Output 1
Output 2
Output 3
Output 4
Maximum Output
SH15-Q2
3.3 V, 300 A
-
-
1500 W
SH15-Q3
5 V, 300 A
-
-
1500 W
SH15-Q4
12 V, 125 A
-
-
1500 W
SH15-Q5
15 V, 100 A
-
-
1500 W
SH15-Q6
24 V, 62.4 A
-
-
1500 W
SH15-Q7
28 V, 53.4 A
-
-
1500 W
SH15-Q8
36 V, 41.6 A
-
-
1500 W
SH15-Q9
48 V, 31.2 A
-
-
1500 W
SH20-P3T53J4
5 V, 150 A
24 V, 10.5 A
SH20-P3T54J5
5 V, 150 A
24 V, 10.5 A
12 V, 25 A
15 V, 20 A
12 V, 20 A
1500 W
15 V, 20 A
1500 W
Single Phase 2000 Watt, SH20 Series
Catalog Number
SH20-Q3K3-7
Output 1
5 V, 420 A
SH20-Q6K6-7
24 V, 87.4 A
SH20-Q9K9-7
Output 2
Output 3
Output 4
Output 5
Output 6
-
-
-
-
-
Maximum Output
2000 W
-
-
-
-
-
2000 W
48 V, 43.7 A
-
-
-
-
-
2000 W
SH20-M3K2
5 V, 240 A
3.3 V, 120 A
12 V, 4 A
-
-
-
2000 W
SH20-Z6Z7M3
5 V, 240 A
12 V, 21 A
12 V, 20 A
5 V, 50 A
15 V, 10 A
24 V, 5 A
2000 W
Three Phase 1500 Watt, S3H15 Series
Output 1
Output 2
Output 3
Output 4
Maximum Output
S3H15-Q2
Catalog Number
3.3 V, 300 A
-
-
-
1500 W
S3H15-Q3
5 V, 300 A
-
-
-
1500 W
S3H15-Q4
12 V, 125 A
-
-
-
1500 W
S3H15-Q5
15 V, 100 A
-
-
-
1500 W
S3H15-Q6
24 V, 62.4 A
-
-
-
1500 W
S3H15-Q7
28 V, 53.4 A
-
-
-
1500 W
S3H15-Q8
36 V, 41.6 A
-
-
-
1500 W
S3H15-Q9
48 V, 31.2 A
-
S3H20-P3T53J4
5 V, 150 A
24 V, 10.5 A
S3H20-P3T54J5
5 V, 150 A
24 V, 10.5 A
12 V, 25 A
15 V, 20 A
-
1500 W
12 V, 20 A
1500 W
15 V, 20 A
1500 W
Three Phase 2000 Watt, S3H20 Series
Catalog Number
Output 1
Output 2
Output 3
Output 4
Output 5
Output 6
Maximum Output
S3H20-Q3K3-7
5 V, 420 A
-
-
-
-
-
2000 W
S3H20-Q6K6-7
24 V, 87.4 A
-
-
-
-
-
2000 W
S3H20-Q9K9-7
48 V, 43.7 A
-
-
-
-
-
2000 W
S3H20-M3K2
5 V, 240 A
S3H20-Z6Z7M3
5 V, 240 A
3.3 V, 120 A
12 V, 21 A
-
-
-
-
2000 W
12 V, 20 A
5 V, 50 A
15 V, 10 A
24 V, 5 A
2000 W
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
SH15 & S3H15 Dimensions
SH20 & S3H20 Dimensions
0.94
MAX
(23.80)
SH20
11.00
(279.31)
7.90
(200.66)
Input
Module
STD AIR FLOW
SLOT 1
SLOT 2
SLOT 3
SLOT 4
AC High
Neutral
Ground
1.2
5.00
MAX
(127.03)
8-32 UNC-2B
Threaded
Insert, 4 Places
Like Pattern
Opposite Side
4.00
(101.60)
Side
J1
2.04
(51.82)
3.49
(88.65)
0.50
(12.70)
0.75
(19.05)
6.750
(171.45)
4.94
(125.48)
0.06
(1.52)
6.39
(162.31)
AC Main Input
Bottom View
Back
1.2
6.75
(171.45)
8-32 UNC-2B
Threaded
Insert, 4 Places
Max Penetration
0.15 (3.81)
0.75
(19.05)
1.067
(27.099)
5.75
(146.05)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
4
Power Supplies
39 Series Copper Line
Specifications
Parameter
Condition
Limit
Input
Input Voltage
105-130/210-260 Vac (user
selectable)
Input Frequency
47 to 440 Hz
Input Protection
Ext. Slow- blow fuse required
Output
Line Regulation
0.1% or 50 mV
Load Regulation
0.1% or 50 mV
Ripple
Full Rated Load
<1% RMS
Controls
E47379
Current Limit Adjust
0-100%
Output Volt Adjust
10-100% Coarse Adjust
(may be mounted remotely).
Fine adjust fine tunes output
for no loads and full load
conditions.
Features
General
• Full range adjustable output voltage and current
• Universal 120/240 Vac, 50/60 Hz input
• Single supply for multiple applications
• Parallel operation for increased power output
• UL Recognized
Operating Temperature
Full Rated Load
0° to 50°C
Storage Temperature
Full Rated Load
-20° to +70°C
Efficiency
Full Rated Load
75%
Vibration
Applications
Shock
• Engineering bench supply
• Test equipment
• Manufacturing test applications
• Automotive product testing
Designed to meet MILSTD-810D, Method 514.3,
Category Procedure 1.
Designed to meet MILSTD-810D, Method 516.3,
Category Procedure 3.
Dimensions
Selection Table
Maximum Current
Catalog
Power
Watts
Number
Amps* @25 Vdc
(Adj. 2.5-25 Vdc)
Amps* @50 Vdc
(Adj. 5-50 Vdc)
Shipping
Weight lbs
(kg)
300
39-407
12 A
6A
23 (10.4)
600
39-408
24 A
12 A
30 (13.6)
1200
39-409
48 A
24 A
73 (33.1)
* Current listed is the maximum at any voltage in that range.
Model
A
B
B1
C
D
E
F
F1
G
G1
39-407
10.4
-
7.7
6.8
3.8
5.3
-
3.5
-
3.6
39-408
11.4
-
7.7
6.8
3.8
5.3
-
3.5
-
4.6
39-409
14.0
11.1
-
10.0
6.0
8.0
8.3
-
3.5
-
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising