Owner`s Manual TSD-GPN1200 Sound Masking Generator

Owner`s Manual TSD-GPN1200 Sound Masking Generator
Owner’s Manual
TSD-GPN1200
Sound Masking Generator
TSD-GPN1200
Sound Masking Generator
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–1–
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Description
The AtlasIED TSD-GPN1200 sound masking generator is perfectly suited for basic sound masking
systems. The analog topology design eliminates repeating cycles commonly found in other
manufacture’s low cost digital designs.
The TSD-GPN1200 includes a selectable pink or white noise generator and incorporates a variable
balanced output to match input requirements of AtlasIED equalizers and amplifiers.
In addition to the line level output, a 4W (70V Masking System) output is provided to power up to
six masking loudspeakers tapped at .5W each. A variable hi-cut filter with operating range between
1kHz and 8kHz at a slope of 6dB per octave supports equalization requirements for most basic 4W
amplifier Sound Masking systems. Both outputs may be used simultaneously allowing large zones
to be addressed with external equalization and amplification while a smaller zone is powered by the
internal amplifier with spectrum control from the internal high cut filter.
The TSD-GPN1200 is part of a full line of AtlasIED Time Saving Devices. These compact
(1.5" x 4" x 2.75") units are designed to solve some of the common audio system problems in the
easiest and in the most efficient and cost-effective way. All models are made from high quality
components and include removable individual I/O connectors for quick and precise wiring, separate
ground terminals for all I/Os assuring secured connections, and removable level controls that can
be replaced with tamper-proof security covers. The TSDs are highly efficient and meet most energy
standards as one 24V DC power supply (available separately) can power multiple Atlas Time Saving
Devices.
Features
Audio Applications
•Analog Topology
• Selectable Pink or White Noise Generator
• Variable Level Control
• Variable Low Pass EQ
• Balanced Line Output
• 4W Speaker Output
• Multiple Mounting Configurations
• Cable Management System
• Separate Ground Connections
• Removable Phoenix Style I/O Connectors
• Meets Most Energy Standards
• Compact Chassis Design
•
•
•
•
Sound Masking
Security Masking
Pink Noise Generator
White Noise Generator
Installation
• Call Centers
•Pharmacies
• Government Buildings
• Medical Facilities
• Open Office Environments
•Schools
• Industrial Facilities
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–2–
Specifications are subject to change without notice.
Owner’s Manual
TSD-GPN1200
Sound Masking Generator
Front Panel Description
2
1
1. Level Control - Adjust the level of the masking signal at the High Level speaker output and at the Line Out if the Pre/Post switch is in the “Post” position. Turn clockwise to increase the signal level and counter-clockwise to decrease it. Note: The Level Control knob can be removed and replaced with a supplied security cover to prevent unauthorized adjustment.
2. Power LED - Illuminates Blue when 24VDC is present.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–3–
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Rear Panel Description
7
7
7
7
1
2
3
4
5
6
TSD Input/Output connections are removable for easy system wiring. The connector has a 3.5mm
pitch between pins.
1. DC Power Input - Each TSD that requires DC power comes with a 2 position connector for
an external 24VDC power supply (sold separately). Because of the low power consumption, a single external power supply may power more than one TSD. Refer to the current requirements in milliamps to match with the appropriate power supply. Note: It is acceptable to exceed the current
of the TSDs but NOT safe to use a power supply that is below the current requirement of the device.
2. Noise Generator Selector - Select the type of noise signal needed for your application. Most
plenum masking uses pink noise when the ceiling has lay-in tiles. If you are masking under a
raised floor or the ceiling is made from gypsum, it is recommended to use “white” noise.
3. EQ Adjust - Varies a low cut filter with a range of 1kHz to 8kHz at 6dB per octave. With this control
turned fully clockwise, the filter will have no effect on the output signal. Rotate the control
counter-clockwise to adjust the filter to your preferred masking spectra. This filter is used with a
1/3rd octave RTA (Real Time Analyzer) for final tuning of your sound masking system.
4. Pre/Post Selector - Determines whether the Line Level Output has the EQ and Gain Control in or
out of the circuit. In “Pre” mode, the Gain Control and the EQ Control will have no effect on the
Line Out, while in “Post” mode, both the EQ and Gain will effect the Line Output.
5. Line Output - A Balanced Line Level Output of the generator is present here. The connections
between devices must be mated properly to the Output connector or signal loss and/or noise may
be introduced. Note: Unbalanced line level inputs can be inserted by using the following wire configuration, tie (short) the (G) and (–) terminals together.
6. High Level Output - Connect up to six (6) 70.7V masking speakers when tapped at 0.5W each for a load no greater than 4W.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–4–
Specifications are subject to change without notice.
Owner’s Manual
TSD-GPN1200
Sound Masking Generator
7. Cable Management Retainer Points - Each TSD includes two cable retainer straps for securing
the included cable management retainers. Remove one of the rear panel screws, align the panel hole with a retainer and firmly tighten the screws.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–5–
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Cable Management
Knob and Security Cover
All front panel level controls feature a removable knob that can be replaced with an included security
cover. Follow these steps to prevent potentiometer damage or unwanted changes.
1. Knob Installation - Turn the potentiometer shaft fully counter-clockwise. Align the knob indicator to the lowest setting on the panel and the potentiometer shaft slot. Carefully press the knob onto
the potentiometer shaft. Do not force or damage may occur to the potentiometer.
2. Security Cover Installation - Remove the knob from the panel and insert the cover. Small pliers may be required to remove the knobs. Align the security cover to the level control panel hole. Push the cover into the hole until it snaps into place. Do not force or damage may occur to the potentiometer.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–6–
Specifications are subject to change without notice.
Owner’s Manual
TSD-GPN1200
Sound Masking Generator
Mounting
Listed below are the ways to mount the TSD and the optional accessories that can be purchased.
1.Velcro™ - Each unit includes two 2" x 2" pieces of industrial-grade Velcro™ with adhesive backing to adhere to any flat surface. Clean all surfaces before applying the adhesive side of the Velcro™.
2. Multi Mount Plate - Each TSD includes a versatile multi-position mounting plate. This plate allows the TSD to be mounted to any surface; but is ideal for use with rear rack rails or side rack hat channels. Use the included M3 x 4mm screws to install the plate on the TSD. Note: Only use the included M3 x 4mm screws as other screws may be too long and will cause internal damage to the TSD. The multi-position mounting plate is a new addition being included with TSDs. If the TSD being used did not include the mounting plate, contact AtlasIED customer service at
1-800-876-3333.
(M3 x 4mm)
(M3 x 4mm)
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–7–
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Optional Mounting Accessories
1. TSD-RMK 19" Width Rack Mount Kit - For 19" rack mounting, AtlasIED offers an optional rack mount kit, the TSD-RMK. This rack mount kit can support up to four TSD units. The kit includes three blank panels designed to fill any unused slots. Use the included hardware to mount the TSD into the rack mount kit using the top mount screw holes on the TSD.
2. TSD-RMKHR Half Width Rack Mount Kit - AtlasIED offers an optional rack mount kit that can be used in half width rack applications including the AtlasIED WMA-HR and AWR-HR models. The TSD-RMKHR can support up to two TSDs. Included is an extra blank panel to fill one of the spaces if only one TSD is being used.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–8–
Specifications are subject to change without notice.
Owner’s Manual
TSD-GPN1200
Sound Masking Generator
3. TSD-RRMK Rear Rack Mounting Kit - For complete flexibility in mounting a TSD or TSD external power supplies the optional TSD-RRMK is available. The TSD-RRMK can support mounting of either two larger TSDs with external power supplies or up to 4 TSD models. Note: Only use the included M3 x 4mm screws as other screws may be too long and will cause internal damage to
the TSD.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–9–
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Block Diagram
PINK/WHITE SWITCH
OT
PINK
GAIN
+
AMP
WHITE
70V MASKING SYSTEM
4W OUTPUT
COM
EQ
+
– LINE OUT
G
PRE/POST EQ SWITCH
DC 24V INPUT
POWER
Specifications
Description
Sound Masking Generator/Amplifier
Chassis Color
Chassis Material
Black
Aluminum
Inputs
Noise Generator
Internal Pink or White Selectable
Outputs
Type
Qty 1, Balanced Line
Connection
Removable 3 Position Captive Screw 3.5mm Spacing
Impedance300Ω Balanced, 150Ω Unbalanced
Line Output Level
Maximum Output 500mV
Type
Connection
Line Output Level
Qty 1, Speaker Out 4W & 70.7V Masking System Speakers
Removable 3 Position Captive Screw 3.5mm Spacing
Maximum Output 4W
Controls
Level Control
Noise Generator Select
Line Out Select
EQ Adjust
Qty 1, Removable Knob with Security Cover
Pink or White
Pre or Post EQ
Recessed Screw Driver
Indicators
PowerBlue
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 10 –
Specifications are subject to change without notice.
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Electrical
Topology
Frequency Response
EQ Filter
Random Analog
20Hz - 20kHz Line Out Pre EQ Only
High Cut, Variable, 1kHz - 8kHz/6dB
Power Requirements
Voltage24VDC
Average Power Consumption 100mA
Average Power Consumption 2.4W
Dimensions
H 1.5" (39mm) x W 4" (101mm) x D 2.75" (70mm)
Weight
6oz, .165kg
Included Accessories
Velcro™Industrial-Grade
Multi-Mount Plate
Qty 1, Includes Two (2) M3 x 4mm Screws
Cable Retainers
Qty 2
Level Control Knob
Qty 1
Level Control Security Cover
Qty 1
Optional Accessories
TSD 24VDC
TSD-RMK
TSD-RMKHR
TSD-RRMK
Power Supply
1 RU 19" Width Rack Mount Panel (Supports 4 TSD Units)
1 RU Half Rack Width Panel (Supports 2 TSD Units)
Rear Rack Mounting Kit
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
– 11 –
Specifications are subject to change without notice.
AtlasIED.com
TSD-GPN1200
Sound Masking Generator
Owner’s Manual
Limited Warranty
All products manufactured by AtlasIED are warranted to the original dealer/installer, industrial or
commercial purchaser to be free from defects in material and workmanship and to be in compliance
with our published specifications, if any. This warranty shall extend from the date of purchase for
a period of three years on all AtlasIED products, including SOUNDOLIER brand, and ATLAS SOUND
brand products except as follows: one year on electronics and control systems; one year on
replacement parts; and one year on Musician Series stands and related accessories. Additionally,
fuses and lamps carry no warranty. AtlasIED will solely at its discretion, replace at no charge or
repair free of charge defective parts or products when the product has been applied and used in
accordance with our published operation and installation instructions. We will not be responsible
for defects caused by improper storage, misuse (including failure to provide reasonable and
necessary maintenance), accident, abnormal atmospheres, water immersion, lightning discharge,
or malfunctions when products have been modified or operated in excess of rated power, altered,
serviced or installed in other than a workman like manner. The original sales invoice should be
retained as evidence of purchase under the terms of this warranty. All warranty returns must comply
with our returns policy set forth below. When products returned to AtlasIED do not qualify for repair
or replacement under our warranty, repairs may be performed at prevailing costs for material and
labor unless there is included with the returned product(s) a written request for an estimate of repair
costs before any nonwarranty work is performed. In the event of replacement or upon completion of
repairs, return shipment will be made with the transportation charges collect.
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL
DAMAGES FOR PERSONAL INJURY, ATLASIED SHALL NOT BE LIABLE IN TORT OR CONTRACT
FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE
INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
AtlasIED does not assume, or does it authorize any other person to assume or extend on its behalf,
any other warranty, obligation, or liability. This warranty gives you specific legal rights and you may
have other rights which vary from state to state.
Service
Should your Atlas TSD require service, please contact the AtlasIED
warranty department at 1-877-689-8055, ext. 277 to obtain an RA number.
AtlasIED Tech Support can be reached at 1-800-876-3333 or support.atlasied.com.
Visit our website at www.AtlasIED.com to see other Atlas products.
©2017 Atlas Sound L.P. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P.
IED is a registered trademark of Innovative Electronic Designs LLC. All Rights Reserved.
All other trademarks are the property of their respective owners. All specs are subject to change without notice. ATS003940 RevC 4/17
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 12 –
Specifications are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising