1705 Digital Multimeter - Colour Brochure

1705 Digital Multimeter - Colour Brochure
CYAN MAGENTA YELLOW BLACK
Technical Specifications
OTHER MEASUREMENT FUNCTIONS
ACCURACY (Main Measurement Functions)
o
o
Accuracies apply for 1 year, 19 C to 25 C. Temperature coefficient outside these limits is <0.1 x quoted range accuracy per oC
DC Volts
Range
100mV
1V
10V
100V
1000V
Accuracy
0.06% ± 3 dig.
0.04% ± 2 dig.
0.06% ± 2 dig.
0.06% ± 2 dig.
0.06% ± 2 dig.
Resolution
Notes
10µV
Input impedance 10MΩ nominal
100µV
Max. input 1kV DC or AC pk
1mV
NMR: >60dB @ 50/60Hz
10mV
CMR: >90dB @ DC/50Hz/60Hz
100mV
AC Volts (True RMS)
Range
Resolution
20kHz - 50kHz
100mV
N/A
10µV
1V
1% ± 50 dig.
100µV
10V
1mV
0.2% ± 20 dig. 0.2% ± 20 dig. 1% ± 80 dig.
100V
10mV
1% ± 80 dig.
750V
N/A
100mV
1V, 10V, 100V ranges are <1dB down at 100kHz. AC accuracies apply
above 1,000 counts. Additional error at crest factor = 3 is typically 0.2%.
Input impedance = 1MΩ nominal. Max. input = 750V rms, 1kV pk.
1kΩ unbalanced CMR = >60dB at DC/50Hz/60Hz.
45Hz - 10kHz
Accuracy
10kHz - 20kHz
1% ± 20 dig.
Resistance
Range
100Ω
1000Ω
10kΩ
100kΩ
1000kΩ
10MΩ
20MΩ
Continuity
Selects 1000Ω range and sounds audible tone for impedance <10Ω.
Sampling rate 20/sec. Max. input 300V DC or AC rms.
Diode Test
Displays voltages up to 1.2V at a test current of 0.5mA. Max. open circuit voltage 4V. Max. input 300V DC or AC rms.
AC + DC Volts, AC + DC Current
Displays the True RMS value of the ac and dc components of the waveform. Accuracy is equal to the sum of the ac and dc accuracies for the
selected range.
DISPLAY
Display Type:
Scale Length:
Annunciators:
Reading Rate:
Overrange:
Overflow:
Resolution
10mΩ
100mΩ
1Ω
10Ω
100Ω
1kΩ
10kΩ
Notes
Max. input 300V DC or AC rms
any range.
Max. open circuit voltage 4V
DC Current
Range
1mA
100mA
10A (up to 1A)
10A (up to 5A)
10A (up to 10A)
Accuracy
0.1% ± 3 dig.
0.1% ± 3 dig.
0.3% ± 3 dig.
1.0% ± 4 dig.
3% ± 10 dig.
Resolution
0.1µA
10µA
1mA
1mA
1mA
Notes
Max. input 500mA
Voltage burden <250mV
Max. input 10A
Voltage burden <500mV
Ohms Null:
Hold:
T-Hold:
dB:
AC plus DC:
% Deviation:
Ax+b:
Limits..
Min/Max:
Power:
VA:
Data Logger:
AC Current (True RMS)
Range
1mA
100mA
10A (up to 1A)
10A (up to 5A)
10A (up to 10A)
Accuracy
Resolution
Notes
0.1µA
0.35% ± 20 dig.
Max. input 500mA
Voltage burden <250mV
10µA
0.35% ± 20 dig.
1mA
0.5% ± 20 dig.
Max. input 10A
1mA
1.2% ± 20 dig.
Voltage burden <500mV
1mA
3% ± 20 dig.
Accuracies apply over 45Hz to 10kHz for readings above 1000 counts.
Additional error at crest factor = 3 is typically 0.2%.
Frequency
Range
100Hz
1000Hz
10kHz
100kHz
Accuracy
0.01% ± 1 dig.
Resolution
0.01Hz
0.1Hz
1Hz
10Hz
Notes
Sensitivity better than
30mV (100mV range),
better than 10% of
range (other Vac & Iac
ranges)
Resolution
10pF
100pF
1nF
10nF
100nF
Notes
Capacitance
Range
10nF
100nF
1µF
10µF
100µF
Accuracy
2% ± 5 dig.
5% ± 5 dig.
Scale length 1200
counts
1705
High contrast LCD. Main display 4½ digits 17mm high,
secondary display 5 digits 10mm high.
4¼ digits (12,000 counts) in most modes.
LCD - annunciators for all ranges, functions and program modes.
Varies with function, maximum 4/sec.
Display flashes 12000 if input too great for range.
Displays -Or- if calculated result overflows display.
COMPUTING FUNCTIONS
Null (Relative)
Accuracy
0.1% ± 3 dig.
0.08% ± 2 dig.
0.09% ± 2 dig.
0.09% ± 2 dig.
0.12% ± 2 dig.
0.5% ± 2 dig.
0.5% ± 2 dig.
THURLBY THANDAR INSTRUMENTS
Stores current reading and subtracts it from future
readings.
Additional non-volatile function for nulling test lead resistance.
Reading is frozen.
Reading is frozen when stable.
Displays measurement in dBm relative to 600Ω or
other user-entered impedance.
The RMS value of the ac plus dc parts of the signal is
calculated and displayed.
Displays % deviation from entered reference value.
Linear scaling of results, with offset.
Reading displayed with HI, LO, or PASS with respect
to user-defined high and low limits.
Minimum and maximum reading stored.
Calculates V2/R and displays in Watts with respect to a
user-defined impedance.
Calculates and displays Volts x Amps.
Manual or automatic storage of 100 measurements.
Storage interval 1s to 9999s, manually from keyboard,
or by remote contact closure or interface command.
INTERFACES
RS232:
GPIB (option):
Baud rates 2400, 9600 or 19200. Complies fully with
the ARC (Addressable RS232 Chain) interface standard. Address selectable from the front panel.
The 1705 can be specified with an IEEE-488 interface.
This version operates only from AC mains.
POWER REQUIREMENTS
AC Input:
Batteries:
Battery Life:
115/230 Volts AC nominal 50/60Hz by internal adjustment; 5VA max.
6 x C cells, disposable or rechargeable.
>150 hours from alkaline disposable cells,
typically 70 hours from rechargeable cells.
GENERAL
Operating Range: +50oC to + 40oC, 20% to 80% RH
Storage Range: -20oC to + 60oC
EMC & Safety: Complies with EN50081-1, EN50082-1 & EN61010-1
Size and Weight: 260(W) x 88(H) x 235(D)mm, excl. handle/feet. 2.0kg.
Thurlby Thandar Instruments Ltd. operates a policy of continuous development and
reserves the right to alter specifications without prior notice.
Designed and built in the U.K. by:
Thurlby Thandar Instruments Ltd.
Glebe Road, Huntingdon Cambs. PE18 7DX England
Tel: 01480 412451 Fax: 01480 450409
82100-0058
High resolution bench/portable true RMS multimeter
Dual display, dual measurement
CYAN MAGENTA YELLOW BLACK
High accuracy, resolution & bandwidth
Dual displays & dual measurement
performance beyond the capability of hand-helds
High resolution & accuracy
The 1705 is a 4¼ digit meter with a scale
length of 12,000 counts and a resolution
of 10µV, 10mΩ and 0.1µA.
Combined with a high basic dcV accuracy
of 0.04%, it provides measurements that
are an order of magnitude better than
most hand-held DMMs.
Dual display system
The 1705 has both a main display and a
secondary display. The two displays can
be used for a variety of purposes:
● To show the selected range in addition
Wide bandwidth ac
with true RMS
The 1705 provides True RMS ac response
which gives accurate measurements regardless of the waveform shape.
The wide bandwidth attenuator provides
high accuracy within the audio band and
gives extended response to avoid errors
when measuring switching waveforms.
Measurements are normally ac coupled
but, when required, the true RMS value of
the ac plus dc components can be shown.
Frequency & capacitance
The 1705 offers high accuracy frequency
measurement (better than 0.01%) from
10Hz to 120kHz. It uses a reciprocal
counting technique to give up to 0.01Hz
resolution at 10 readings per second.
The 1705 also incorporates capacitance
measurement in four ranges up to 120µF.
‘smart’ functions, RS232 or GPIB interfaces
Dual measurement ✱
Dual displays
The 1705 can measure and display two
signals simultaneously. These can be two
parameters of one signal (e.g. ac volts &
dc volts) or two signals applied to different
sockets (e.g. ac volts & ac current).
The 1705 has a number of powerful builtin functions designed to make life easier
for the user. Most of these functions
make use of the dual displays to provide
extra information.
Smart functions
for added power
dB measurements
AC voltages can be displayed in dB as
well as voltage Built-in zero reference
scaling enables voltages to be displayed
in dBm relative to any required impedance.
Linear scaling with offset
Examples
Main
display
dc Volts
dc Volts
ac Volts
ac Volts
dc Amps
ac Amps
Signal
inputs
1
2
1
2
1
2
Function
dB
Null
Power
VA
Limits
Ax + B
Main
display
dBm
nulled value
ac Volts
dc Amps
Resistance
dc Volts
Secondary
display
ac Volts
raw value
V2/R
Volts x Amps
Hi/Lo/Pass
Weight
to the measurement units (e.g. 100mA dc).
● To display a measurement in two different units (e.g. ac volts and dBm).
● To display the result of a calculated
function (e.g. Ωs value and % deviation).
● To measure and display two parameters of one signal (e.g. ac and dc volts). ✱
● To measure and display two different
signals (e.g. ac volts and dc current). ✱
This means, for example, that the electrical output of a transducer can be scaled
to give a direct readout of the physical parameter e.g. temperature or weight. It is
particularly useful with 4-20mA current
loops.
This function enables the reading to be
tested against high and low limits set by
the user. The display then shows HI, LO
or PASS in addition to the measurement
result.
Auto or manual ranging
The 1705 offers fully automatic ranging
on all functions. Alternatively, ranges can
be selected manually.
Unlike other meters, the range value can
be clearly shown on the secondary display avoiding any possibility of confusion.
Closed case calibration
●
Full safety protection
●
The 1705 incorporates extensive protection
against damage from accidental overloads
on all ranges including 10 Amps.
It also meets the stringent safety requirements of IEC1010-1 for measurements
up to 1kV (Cat. I) or 600V (Cat. II).
●
Mains or battery operation
The 1705 can operate either from ac
mains or from batteries (disposable or rechargeable). In battery mode it can operate for up to 80 hours.
●
●
●
●
●
●
High performance 12,000 count autoranging DMM
High accuracy and resolution: 0.04%, 10µV, 10mΩ
Dual display and dual measurement technology ✱
Large and clear LCD (17mm digits) with annunciators ✱✱
True RMS ac functions; Frequency and Capacitance
Wide range of computing functions, e.g. Ax + b
100 step data-logger, timed or triggered logging
RS232 interface standard, GPIB interface optional
Mains and battery operation as standard
In addition to dBs, the 1705 can measure
power in Watts or VA.
For resistive loads the Watts function calculates V2/R for any load resistance between 1Ω and 10kΩ, a particularly useful
function for audio measurements.
The VA function makes use of the dual
measurement capability and displays the
product of voltage and current.
Limits comparison
The 1705 stores its calibration constants
in protected memory and can be recalibrated without ever opening the case.
Power measurement
in Watts or VA
This function enables a reading to be multiplied by a scale factor (A) and for an offset (b) to be added or subtracted.
Examples
Secondary display
ac Volts
ac Amps
Frequency
dc Amps
ac Amps
ac Volts
and avoiding ‘missed’ readings when using the Logger function.
Tracking ‘hold’
The T-Hold function freezes the display
every time a new but stable reading is detected. This avoids the problem of trying
to watch the test points and the display simultaneously. Alternatively, a simple
Hold function is also available.
Relative measurement
The null function stores the current reading and subtracts it from future readings
giving a ‘relative’ display. The nulled and
normal readings can be viewed together.
A separate Ω-null function retains an independent null value for resistance
measurements enabling test lead resistance to be permanently nulled out.
Percentage deviation (∆%)
This function enables the meter to display
the percentage amount by which the
reading differs from a nominal value chosen by the user. It is invaluable for measuring tolerance or stability.
Min-Max storage
The Min-Max function stores the highest
and lowest values of a set of readings.
This facility has many uses such as
checking for power supply glitches, recording peak temperature excursions
Automatic data logging
The 1705 can store up to 100 readings at
any required time interval from 1 reading
per second up to 1 reading every 3 hours.
A simple recall sequence allows the readings to be scrolled onto the display whenever required. Alternatively results can
be downloaded using RS232 or GPIB.
As a result, tedious time related measurement sequences can be handled automatically without disrupting your work.
Manual storage of readings is also available eliminating the need for paper and
pencil when making a series of measurements. Storage can also be triggered
from contact closure or the digital interfaces.
Full bus control
via RS-232 or GPIB
The 1705 has an RS-232 interface as
standard which can be used for remote
control and read-back of measurements.
As well as operating as a conventional
RS-232 interface, it can also be used in
addressable mode whereby up to 32 in-
✱ The 1705 uses a true dual measurement, dual display technique licensed under U.S. Patent
No. 4 825 392. Low cost meters incorporating two displays do not have the same functionality.
✱✱ Screen illustrations are at approximately 70% of actual size.
CYAN MAGENTA YELLOW BLACK
High accuracy, resolution & bandwidth
Dual displays & dual measurement
performance beyond the capability of hand-helds
High resolution & accuracy
The 1705 is a 4¼ digit meter with a scale
length of 12,000 counts and a resolution
of 10µV, 10mΩ and 0.1µA.
Combined with a high basic dcV accuracy
of 0.04%, it provides measurements that
are an order of magnitude better than
most hand-held DMMs.
Dual display system
The 1705 has both a main display and a
secondary display. The two displays can
be used for a variety of purposes:
● To show the selected range in addition
Wide bandwidth ac
with true RMS
The 1705 provides True RMS ac response
which gives accurate measurements regardless of the waveform shape.
The wide bandwidth attenuator provides
high accuracy within the audio band and
gives extended response to avoid errors
when measuring switching waveforms.
Measurements are normally ac coupled
but, when required, the true RMS value of
the ac plus dc components can be shown.
Frequency & capacitance
The 1705 offers high accuracy frequency
measurement (better than 0.01%) from
10Hz to 120kHz. It uses a reciprocal
counting technique to give up to 0.01Hz
resolution at 10 readings per second.
The 1705 also incorporates capacitance
measurement in four ranges up to 120µF.
‘smart’ functions, RS232 or GPIB interfaces
Dual measurement ✱
Dual displays
The 1705 can measure and display two
signals simultaneously. These can be two
parameters of one signal (e.g. ac volts &
dc volts) or two signals applied to different
sockets (e.g. ac volts & ac current).
The 1705 has a number of powerful builtin functions designed to make life easier
for the user. Most of these functions
make use of the dual displays to provide
extra information.
Smart functions
for added power
dB measurements
AC voltages can be displayed in dB as
well as voltage Built-in zero reference
scaling enables voltages to be displayed
in dBm relative to any required impedance.
Linear scaling with offset
Examples
Main
display
dc Volts
dc Volts
ac Volts
ac Volts
dc Amps
ac Amps
Signal
inputs
1
2
1
2
1
2
Function
dB
Null
Power
VA
Limits
Ax + B
Main
display
dBm
nulled value
ac Volts
dc Amps
Resistance
dc Volts
Secondary
display
ac Volts
raw value
V2/R
Volts x Amps
Hi/Lo/Pass
Weight
to the measurement units (e.g. 100mA dc).
● To display a measurement in two different units (e.g. ac volts and dBm).
● To display the result of a calculated
function (e.g. Ωs value and % deviation).
● To measure and display two parameters of one signal (e.g. ac and dc volts). ✱
● To measure and display two different
signals (e.g. ac volts and dc current). ✱
This means, for example, that the electrical output of a transducer can be scaled
to give a direct readout of the physical parameter e.g. temperature or weight. It is
particularly useful with 4-20mA current
loops.
This function enables the reading to be
tested against high and low limits set by
the user. The display then shows HI, LO
or PASS in addition to the measurement
result.
Auto or manual ranging
The 1705 offers fully automatic ranging
on all functions. Alternatively, ranges can
be selected manually.
Unlike other meters, the range value can
be clearly shown on the secondary display avoiding any possibility of confusion.
Closed case calibration
●
Full safety protection
●
The 1705 incorporates extensive protection
against damage from accidental overloads
on all ranges including 10 Amps.
It also meets the stringent safety requirements of IEC1010-1 for measurements
up to 1kV (Cat. I) or 600V (Cat. II).
●
Mains or battery operation
The 1705 can operate either from ac
mains or from batteries (disposable or rechargeable). In battery mode it can operate for up to 80 hours.
●
●
●
●
●
●
High performance 12,000 count autoranging DMM
High accuracy and resolution: 0.04%, 10µV, 10mΩ
Dual display and dual measurement technology ✱
Large and clear LCD (17mm digits) with annunciators ✱✱
True RMS ac functions; Frequency and Capacitance
Wide range of computing functions, e.g. Ax + b
100 step data-logger, timed or triggered logging
RS232 interface standard, GPIB interface optional
Mains and battery operation as standard
In addition to dBs, the 1705 can measure
power in Watts or VA.
For resistive loads the Watts function calculates V2/R for any load resistance between 1Ω and 10kΩ, a particularly useful
function for audio measurements.
The VA function makes use of the dual
measurement capability and displays the
product of voltage and current.
Limits comparison
The 1705 stores its calibration constants
in protected memory and can be recalibrated without ever opening the case.
Power measurement
in Watts or VA
This function enables a reading to be multiplied by a scale factor (A) and for an offset (b) to be added or subtracted.
Examples
Secondary display
ac Volts
ac Amps
Frequency
dc Amps
ac Amps
ac Volts
and avoiding ‘missed’ readings when using the Logger function.
Tracking ‘hold’
The T-Hold function freezes the display
every time a new but stable reading is detected. This avoids the problem of trying
to watch the test points and the display simultaneously. Alternatively, a simple
Hold function is also available.
Relative measurement
The null function stores the current reading and subtracts it from future readings
giving a ‘relative’ display. The nulled and
normal readings can be viewed together.
A separate Ω-null function retains an independent null value for resistance
measurements enabling test lead resistance to be permanently nulled out.
Percentage deviation (∆%)
This function enables the meter to display
the percentage amount by which the
reading differs from a nominal value chosen by the user. It is invaluable for measuring tolerance or stability.
Min-Max storage
The Min-Max function stores the highest
and lowest values of a set of readings.
This facility has many uses such as
checking for power supply glitches, recording peak temperature excursions
Automatic data logging
The 1705 can store up to 100 readings at
any required time interval from 1 reading
per second up to 1 reading every 3 hours.
A simple recall sequence allows the readings to be scrolled onto the display whenever required. Alternatively results can
be downloaded using RS232 or GPIB.
As a result, tedious time related measurement sequences can be handled automatically without disrupting your work.
Manual storage of readings is also available eliminating the need for paper and
pencil when making a series of measurements. Storage can also be triggered
from contact closure or the digital interfaces.
Full bus control
via RS-232 or GPIB
The 1705 has an RS-232 interface as
standard which can be used for remote
control and read-back of measurements.
As well as operating as a conventional
RS-232 interface, it can also be used in
addressable mode whereby up to 32 in-
✱ The 1705 uses a true dual measurement, dual display technique licensed under U.S. Patent
No. 4 825 392. Low cost meters incorporating two displays do not have the same functionality.
✱✱ Screen illustrations are at approximately 70% of actual size.
CYAN MAGENTA YELLOW BLACK
Technical Specifications
OTHER MEASUREMENT FUNCTIONS
ACCURACY (Main Measurement Functions)
o
o
Accuracies apply for 1 year, 19 C to 25 C. Temperature coefficient outside these limits is <0.1 x quoted range accuracy per oC
DC Volts
Range
100mV
1V
10V
100V
1000V
Accuracy
0.06% ± 3 dig.
0.04% ± 2 dig.
0.06% ± 2 dig.
0.06% ± 2 dig.
0.06% ± 2 dig.
Resolution
Notes
10µV
Input impedance 10MΩ nominal
100µV
Max. input 1kV DC or AC pk
1mV
NMR: >60dB @ 50/60Hz
10mV
CMR: >90dB @ DC/50Hz/60Hz
100mV
AC Volts (True RMS)
Range
Resolution
20kHz - 50kHz
100mV
N/A
10µV
1V
1% ± 50 dig.
100µV
10V
1mV
0.2% ± 20 dig. 0.2% ± 20 dig. 1% ± 80 dig.
100V
10mV
1% ± 80 dig.
750V
N/A
100mV
1V, 10V, 100V ranges are <1dB down at 100kHz. AC accuracies apply
above 1,000 counts. Additional error at crest factor = 3 is typically 0.2%.
Input impedance = 1MΩ nominal. Max. input = 750V rms, 1kV pk.
1kΩ unbalanced CMR = >60dB at DC/50Hz/60Hz.
45Hz - 10kHz
Accuracy
10kHz - 20kHz
1% ± 20 dig.
Resistance
Range
100Ω
1000Ω
10kΩ
100kΩ
1000kΩ
10MΩ
20MΩ
Continuity
Selects 1000Ω range and sounds audible tone for impedance <10Ω.
Sampling rate 20/sec. Max. input 300V DC or AC rms.
Diode Test
Displays voltages up to 1.2V at a test current of 0.5mA. Max. open circuit voltage 4V. Max. input 300V DC or AC rms.
AC + DC Volts, AC + DC Current
Displays the True RMS value of the ac and dc components of the waveform. Accuracy is equal to the sum of the ac and dc accuracies for the
selected range.
DISPLAY
Display Type:
Scale Length:
Annunciators:
Reading Rate:
Overrange:
Overflow:
Resolution
10mΩ
100mΩ
1Ω
10Ω
100Ω
1kΩ
10kΩ
Notes
Max. input 300V DC or AC rms
any range.
Max. open circuit voltage 4V
DC Current
Range
1mA
100mA
10A (up to 1A)
10A (up to 5A)
10A (up to 10A)
Accuracy
0.1% ± 3 dig.
0.1% ± 3 dig.
0.3% ± 3 dig.
1.0% ± 4 dig.
3% ± 10 dig.
Resolution
0.1µA
10µA
1mA
1mA
1mA
Notes
Max. input 500mA
Voltage burden <250mV
Max. input 10A
Voltage burden <500mV
Ohms Null:
Hold:
T-Hold:
dB:
AC plus DC:
% Deviation:
Ax+b:
Limits..
Min/Max:
Power:
VA:
Data Logger:
AC Current (True RMS)
Range
1mA
100mA
10A (up to 1A)
10A (up to 5A)
10A (up to 10A)
Accuracy
Resolution
Notes
0.1µA
0.35% ± 20 dig.
Max. input 500mA
Voltage burden <250mV
10µA
0.35% ± 20 dig.
1mA
0.5% ± 20 dig.
Max. input 10A
1mA
1.2% ± 20 dig.
Voltage burden <500mV
1mA
3% ± 20 dig.
Accuracies apply over 45Hz to 10kHz for readings above 1000 counts.
Additional error at crest factor = 3 is typically 0.2%.
Frequency
Range
100Hz
1000Hz
10kHz
100kHz
Accuracy
0.01% ± 1 dig.
Resolution
0.01Hz
0.1Hz
1Hz
10Hz
Notes
Sensitivity better than
30mV (100mV range),
better than 10% of
range (other Vac & Iac
ranges)
Resolution
10pF
100pF
1nF
10nF
100nF
Notes
Capacitance
Range
10nF
100nF
1µF
10µF
100µF
Accuracy
2% ± 5 dig.
5% ± 5 dig.
Scale length 1200
counts
1705
High contrast LCD. Main display 4½ digits 17mm high,
secondary display 5 digits 10mm high.
4¼ digits (12,000 counts) in most modes.
LCD - annunciators for all ranges, functions and program modes.
Varies with function, maximum 4/sec.
Display flashes 12000 if input too great for range.
Displays -Or- if calculated result overflows display.
COMPUTING FUNCTIONS
Null (Relative)
Accuracy
0.1% ± 3 dig.
0.08% ± 2 dig.
0.09% ± 2 dig.
0.09% ± 2 dig.
0.12% ± 2 dig.
0.5% ± 2 dig.
0.5% ± 2 dig.
THURLBY THANDAR INSTRUMENTS
Stores current reading and subtracts it from future
readings.
Additional non-volatile function for nulling test lead resistance.
Reading is frozen.
Reading is frozen when stable.
Displays measurement in dBm relative to 600Ω or
other user-entered impedance.
The RMS value of the ac plus dc parts of the signal is
calculated and displayed.
Displays % deviation from entered reference value.
Linear scaling of results, with offset.
Reading displayed with HI, LO, or PASS with respect
to user-defined high and low limits.
Minimum and maximum reading stored.
Calculates V2/R and displays in Watts with respect to a
user-defined impedance.
Calculates and displays Volts x Amps.
Manual or automatic storage of 100 measurements.
Storage interval 1s to 9999s, manually from keyboard,
or by remote contact closure or interface command.
INTERFACES
RS232:
GPIB (option):
Baud rates 2400, 9600 or 19200. Complies fully with
the ARC (Addressable RS232 Chain) interface standard. Address selectable from the front panel.
The 1705 can be specified with an IEEE-488 interface.
This version operates only from AC mains.
POWER REQUIREMENTS
AC Input:
Batteries:
Battery Life:
115/230 Volts AC nominal 50/60Hz by internal adjustment; 5VA max.
6 x C cells, disposable or rechargeable.
>150 hours from alkaline disposable cells,
typically 70 hours from rechargeable cells.
GENERAL
Operating Range: +50oC to + 40oC, 20% to 80% RH
Storage Range: -20oC to + 60oC
EMC & Safety: Complies with EN50081-1, EN50082-1 & EN61010-1
Size and Weight: 260(W) x 88(H) x 235(D)mm, excl. handle/feet. 2.0kg.
Thurlby Thandar Instruments Ltd. operates a policy of continuous development and
reserves the right to alter specifications without prior notice.
Designed and built in the U.K. by:
Thurlby Thandar Instruments Ltd.
Glebe Road, Huntingdon Cambs. PE18 7DX England
Tel: 01480 412451 Fax: 01480 450409
82100-0058
High resolution bench/portable true RMS multimeter
Dual display, dual measurement
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising