Owner`s Manual - LT Rush Stone

Owner`s Manual - LT Rush Stone
Owner’s Manual
Operation & Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with question on installation, operation, or service.
WARNING
NOTICE: DO NOT DISCARD THIS MANUAL
5700 STEP TOP WOOD STOVE SERIES
Automatic Combustion Control (ACC)
Model(s):
57ST-ACC
If the information in these instructions is not followed exactly, a
fire could result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire - If heater or chimney connector glows, you are overfiring. Overfiring
will void your warranty.
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
WARNING
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
Tested and
Listed by
Portland
Oregon USA
O-T L
C
US
OMNI-Test Laboratories, Inc.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may overfire and generate
poisonous gases (i.e. carbon monoxide).
Hot glass will cause burns.
•
Do not touch glass until it is cooled
•
NEVER allow children to touch glass
•
Keep children away
•
CAREFULLY SUPERVISE children in same room as
fireplace.
•
Alert children and adults to hazards of high temperatures
•
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other flammable
materials away.
NOTE
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies recommends NFI certified professionals, or technicians supervised by an NFI certified
professional.
1
To obtain a French translation of this manual, please contact
your dealer or visit www.quadrafire.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrafire.com
7038-207D
May 4, 2015
5700 STEP TOP ACC
and Welcome to the Quadra-Fire Family!
advanced technology to achieve the optimum operation of our stoves, inserts and fireplaces. And yet we are
old-fashioned when it comes to craftsmanship. Each unit
is meticulously fabricated and gold and nickel surfaces are
hand-finished for lasting beauty and enjoyment. Our pledge
to quality is completed as each model undergoes a quality
control inspection.
A. Congratulations
Hearth & Home Technologies welcomes you to our tradition
of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and
performance.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
B. Sample of Serial Number / Safety Label
LOCATION: Back of unit
WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS.
CAUTION: HOT
FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS
KEEP
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT
CAUSER DES BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR
ATTENTION:PEUT
L'ÉTIQUETTE ET LES INSTRUCTIONS.
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES. (UM)
84-HUD . "For Use with Solid Wood Fuel Only"
APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE
COMBUSTIBLE SOLIDE, POUR USAGE DANS LES
MAISONS MOBILES. (UM) 84 HUD. "Pour Usage Avec
Bois Solide Seulement"
PREVENT HOUSE FIRES
Install and use only in accordance with
manufacturer's
installation
and
operating
instructions. Contact local building or fire officials
about restrictions and installation inspections in
your area. Do not obstruct the space beneath
heater.
SUITABLE FOR MOBILE HOME INSTALLATION
WARNING - For Mobile Homes: Do not install in
a sleeping room. An outside combustion air inlet
must be provided and unrestricted while unit is in
use. The structural integrity of the mobile home
floor, ceiling and walls must be maintained. The
stove needs to be properly grounded to the frame
of the mobile home. Components required for
mobile home installation: Outside Air Kit, Part
Number OAK-ACC.
Refer to manufacturer's instructions and local
codes for precautions required for passing
chimney through a combustible wall or ceiling and
maximum offsets.
Inspect and clean chimney frequently - Under
Certain Conditions of Use, Creosote Buildup May
Occur Rapidly.
Do not connect this unit to a chimney serving
another appliance.
Optional Components: Optional Blower, Part
BK-ACC.
Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.
Route power cord away from unit. Do not route
cord under or in front of appliance.
DANGER: Risk of electrical shock. Disconnect
power supply before servicing.
Replace glass only with 5mm ceramic available
from your dealer.
Do not use grate or elevate fire. Build wood fire
directly on hearth.
Do not overfire - if heater or chimney connector
glows, you are overfiring.
OPERATE ONLY WITH DOORS CLOSED
Open only to add fuel to the fire.
Do NOT operate before fully assembling
components.
WARNING: Only used approved wood fuel listed
in owners manual. Burning any other fuel will void
warranty.
FLOOR PROTECTION:
Floor protector must be a 1 inch min. thickness, ("k" value =
.49, R value = 2.04) non-combustible material or equivalent,
extending beneath heater and to front/sides/rear as indicated
on the diagram below. Exception: Non-combustible floor
protections must extend beneath the flue pipe when installed
with horizontal venting and extend 2 inches (51mm) beyond
each side.
45-7/8”
minimum
O-T L
C
PRÉVENTION DES FEUX DE MAISON
PROTECTION DU PLANCHER:
Le protecteur de plancher doit être d'un minimum de 1 inch
(25mm) d'épaisseur, ('k" value = .49, R value = 2.04) de matériel
incombustible ou équivalent, s'étendant du dessous de l'appareil
de chauffage à l'avant, aux cotés et à l'arrière comme indiqué
sur le diagramme suivant. Exception: Les protections
incombustibles du plancher doivent s'étendre en dessous du
conduit de cheminée lorsqu'installées avec une ventilation à
l'horizontale et s'étendre de 2 inches (51mm) de chaque côté.
203mm
(8")
203mm
(8")
1419mm
(55-7/8")
minimum
5700 Step Top ACC
VENT SPECIFICATIONS:
SPÉCIFICATIONS DE LA VENTILATION:
SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black
or blued steel connector pipe, with a listed factory-built UL103HT* Class "A"
chimney, suitable for use with solid fuels, or a masonry chimney, and the
referenced clearances.
MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de
minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en usine
UL103HT* de Classe "A", adéquate pour usage avec les combustions solides, ou une
cheminée de briques, avec espaces libres référés.
MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air
isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe "A:, ou
une cheminée de briques, avec espaces libres alloués.
MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk
Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les
espaces libres pour mur double comme mentionné ci-bas.
DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air
insulated connector pipe with listed factory-built UL103HT* Class "A" chimney,
or a masonry chimney and the referenced clearances
MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos
E
L
DS or Security DL double wall connector pipe. Must be equipped with a spark
arrestor. Apply double wall clearances below when installing unit.
INSTALLATION: FULL VERTICAL INSTALLATION: ENTIÈREMENT VERTICALE
A
B
P
C
D
E
F
G
USA
457mm (18")
CANADA
33-5/8”
minimum
Manufactured by:
Fabriqué par: 1445 N. Highway, Colville, WA 99114
www.quadrafire.com
H
SINGLE WALL PIPE
12.5 (318)10.5 (267)25.5 (648)15 (381) 2 (51) 12 (305) 45 (1143) N/A
DOUBLE WALL PIPE
9.5 (241) 7.5 (191)25.5 (648) 15 (381)
M
2 (51) 12 (305) 45 (1143) N/A
CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE
CORNER
INSTALLATION/
INSTALLATION
DU COIN
*
*
45 (1143) 18 (457)*
CONDUIT DU MUR SIMPLE
9.5 (241) 7.5 (191)25.5 (648) 15 (381)
*
*
45 (1143) 13 (330)
CONDUIT DU MUR DOUBLE
SINGLE WALL PIPE
9.5 (241) 7.5 (191)25.5 (648) 15 (381)
2 (51) 12 (305) 45 (1143) 18 (457)*
CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE
9.5 (241) 7.5 (191)25.5 (648) 15 (381)
2 (51) 12 (305) 45 (1143) 13 (330)
CONDUIT DU MUR DOUBLE
INSTALLATION: ALCOVE - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT** listed factory-built
Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48
inches (1219mm) with a minimum height of 79.25 inches (2013mm) from floor to bottom of ceiling and the referenced clearances.
INSTALLATION: ALCÔVE - De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine
UL103HT** de Classe "A", ou une cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de
l'alcôve ne doit pas être de plus de 48 inches (1219mm) avec une hauteur minimum de 45 inches (1143mm) la distance entre du plancher et plafond inférieur,
et des espaces libres alloués.
(**In Canada must comply with Standard CAN/ULC-S629-M87 for the 650oC Factory-built chimney.)
(**Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650oC cheminée bâtit en usine.)
10.5 (268) 8.5 (216)25.5 (648)15 (381)
N/A
N/A
* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED
45 (1143)
*
B
C
Test Lab &
Report No.
D
E
F
E
F
9.5 (241) 7.5 (191)25.5 (648) 15 (381)
INSTALLATION: 90o ELBOW OFF TOP OF STOVE THROUGH BACKWALL
INSTALLATION: 90o DU COURBURE AU DESSUS DE HAUT DU POÊLE A TRAVERS LE MUR ARRIERE
DOUBLE WALL PIPE
A
CONDUIT DU MUR DOUBLE
INSTALLATION: HORIZONTAL WITH MINIMUM 2 FT VERTICAL OFF STOVE TOP
INSTALLATION: HORIZONTALE AVEC 609mm VERTICAL MINIMUM DU HAUT DU POÊLE
SINGLE WALL PIPE
BACKWALL/SIDE
WALL/
MUR
ARRIÈRE/MUR
DE CÔTÉ
Serial No.
Model
Name
ESPACES LIBRES MIN DES MATÉRIAUX COMBUSTIBLES: En Pouces & (millimètres)
NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur
de l'entrée du conduit.
MIN CLEARANCES TO COMBUSTIBLE MATERIALS: Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of flue collar.
8"
16" from glass
007009
TESTED TO:/ TESTÉ À:
UL 1482-96, ULC S627-00
Report / Rapport
#061-S-73-6.2
A
S
Ne mettez PAS le poêle en marche tant que tous les
composants n’ont pas été entièrement assemblés.
ATTENTION: Seulement utilisé carburant approuvé
indiquée dans le manuel des propriétaires. La
combustion d'autres combustibles annulera la garantie.
Fuel loading door
Portland
Oregon USA
US
OMNI-Test Laboratories, Inc.
Installez et utilisez en accord avec les instructions
d'installation et d'opération du fabricant. Contactez le
bureau de la construction ou le bureau des incendies au
sujet des restrictions et des inspections d'installation dans
votre voisinage. Ne pas obstruez l'espace en dessous de
l'appareil.
CONVIENT POUR UNE INSTALLATION MAISON MOBILE
AVIS - Pour Les Maisons Mobiles: Ne pas installer dans
une chambre à coucher. Un tuyau extérieur de
combustion d'air doit être installé et ne doit pas être
obstrué lorsque l'appareil est en usage. La structure
intégrale du plancher, du plafond et des murs de la
maison mobile doit être maintenue intacte. L'appareil de
chauffage doit être fixé à la charpente de la maison
mobile. Les composants requis pour l'installation des
maisons mobiles: Assemblage d'air extérieur, Numéro de
Pièce OAK-ACC.
Référez vous aux instructions du fabricant et des codes
locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles,
et les compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Sous
certaines conditions, il se peut que la créosote
s'accumule rapidement.
Ne pas connecter cet appareil à une cheminée servant un
autre appareil.
Composants Optionnels: Ventilateur Optionnel, Pièce
BK-ACC.
Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.
Éloignez le fil électrique de l'appareil. Ne pas faire passer
le fil électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique.
Déconnectez le fil électrique de la prise de contact avant
le service.
Remplacez la vitre seulement avec une vitre céramique
de 5 mm disponible chez votre fournisseur.
N'élevez pas le feu. Bâtissez le feu de bois directement
sur l'âtre.
Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau
de cheminée rougissent, vous surchauffez.
Opérez l'appareil seulement lorsque la porte de
chargement est fermée. Ouvrez la porte seulement
lorsque vous devez ajouter des combustibles dans le feu.
203mm (8")
SERIAL NO. / NUMÉRO DE SÉRIE
R
Tested and
Listed by
ALCOVE SIDE
VIEW /
VUE DE CÔTÉ
DE L'ALCÔVE
G
A
B
ALCOVE TOP
VIEW /
VUE DU HAUT DE
L'ALCÔVE
90 OFF TOP UP & OUT
CEILING CLEARANCE/
ESPACE LIBRE DU
DESSUS DE
L'APPAREIL AU
PLAFOND AVEC 90 DE
COURBURE
C
D
H
G
CONDUIT DU MUR DOUBLE
STOVE TO CEILING CLEARANCE/
ESPACE LIBRE DU POÊLE AU
PLAFOND
1092mm (43")min
Made in U.S.A. of US and
imported parts.
Fabriqué aux États-Unis-d’Amérique par
des pièces d’origine américaine et pièces
importées.
2015 2016 2017 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with 2015
particulate emission standards at 2.3 G/HR EPA Methods 28 and 5G. Not approved for
sale after May 15, 2020. This wood heater needs periodic inspection and repair for
proper operation. Consult the owner’s manual for further information. It is against federal
regulations to operate this wood heater in a manner inconsistent with the operating
instructions in the owner’s manual.
Mfg. Date
7038-162G
2
7038-207D
May 4, 2015
5700 STEP TOP ACC
Safety Alert Key:
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
•
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
•
NOTICE: Indicates practices which may cause damage to the appliance or to property.
TABLE OF CONTENTS
A. Congratulations .................................................................2
B. Sample of Serial Number / Safety Label ...........................2
C. Warranty Policy .................................................................4
D. Quick Start Guide ..............................................................6
1 Listing and Code Approvals .............7
A.
B.
C.
D.
Appliance Certification ......................................................7
BTU & Efficiency Specifications........................................7
Mobile Home Approved .................................................... 7
Glass Specifications .........................................................7
2 Operating Instructions ......................8
A. Over-Firing Your Appliance ...............................................8
B. Wood Selection & Storage................................................8
C. Burning Process ...............................................................8
D. Automatic Combustion Control (ACC) ..............................9
E. Air Controls ......................................................................9
F. Burn Rates and Operating Efficiency ...............................10
G. Building A Fire .................................................................11
H. Correct Baffle & Blanket Placement .................................12
I. Blower Operating Instructions ...........................................13
J. Opacity (Smoke) ...............................................................13
K. Clear Space ......................................................................14
L. Frequently Asked Questions .............................................14
May 4, 2015
3 Maintenance and Service ................15
A. Quick Reference Maintenance Guide ................................15
B. General Maintenance .......................................................16
4 Troubleshooting Guide....................18
5 Service Part Replacement ...............19
A.
B.
C.
D.
E.
F.
Glass Replacement ..........................................................19
Snap Disc Replacement ...................................................19
Baffle Removal ................................................................20
Firebrick Replacement .....................................................20
Door Handle Assembly ....................................................20
Tube Channel Assembly Replacement ............................21
6 Reference Materials .........................22
A. Service & Maintenance Log ...............................................22
B. Service Parts & Accessories ..............................................23
7038-207D
3
5700 STEP TOP ACC
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
C. Warranty Policy
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Firepots and burnpots
X
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4
7038-207D
May 4, 2015
5700 STEP TOP ACC
WARRANTY CONDITIONS:
!
"
"
WARRANTY EXCLUSIONS:
^
!
*
N
!!
!!!
!!
*
@
%
^!!"!
"!
!!!
Z
*!
!
N
^_`q
!
!
!
!
;_{q
;_|q
;_}q
!!!
!
!!
~
;_q
!+!
!
!"#
!
*
;_€q
;_q
*
;_‚q*
;
~
_ƒq
?#!
%
#*
'
*'
!
!
This warranty is void if:
#
!
!
$
#
!!
!
!!
"
%
!
!
LIMITATIONS OF LIABILITY:
'*
'
!
!*
!
!
!
!
!
!
+8
*
+!
;
!
<=<>$
<<=<?>@$KN<NOQRU!Z[<8?$<=>@<88U@@?<8$<@?<U@@?Q
8><\<N<@<?<N]@$?$\?QZ>R<NU@@?Q8RZ<N$N]@$?$\<
<=>@<88<NU@@?Q8><\<NO$K<
May 4, 2015
7038-207D
5
5700 STEP TOP ACC
D. Quick Start Guide
Note: These are generic drawings and may not represent your specific model.
ITEMS NEEDED FOR FIRST FIRE:
OPEN AIR CONTROLS
10 Pieces of Newspaper, 10-20 Pieces of Dry Kindling
and a Few Pieces of Dry Split Wood.
ADD NEWSPAPER
LOAD WOOD
HIGH
LOW
BURN RATE CONTROL
Upper Right Corner
1
3
2
ADD KINDLING
WARNING! Risk of Fire
Close and securely latch the door after
the fire has started, and after refueling, to
prevent:
• Spillage of smoke, flame and carbon
monoxide
• Spillage of sparks, coals and logs
• Over-firing
DO NOT leave the stove unattended with
the door open.
LIGHT THE PAPER
Starting a fire may not require an open
door for draft. The air control should
supply adequate draft.
4
5
REDUCE AIR
CONTROL
ADD MORE WOOD
Set to desired heat
output
HIGH
The stove is ready for
normal operation.
LOW
BURN RATE CONTROL
Upper Right Corner
7
6
6
7038-207D
May 4, 2015
5700 STEP TOP ACC
1
Listing and Code Approvals
A. Appliance Certification
C. Mobile Home Approved
• This appliance is approved for mobile home installations when not installed in a sleeping room and when
an outside combustion air inlet is provided.
Model:
5700 Step Top Uni-Body (ACC)
Laboratory:
OMNI Test Laboratories, Inc.
Report No:
061-S-73-6.2
Type:
Listed Room Heater, Solid Fuel Type
Standard:
UL1482-96 and ULC S627-00
and (UM) 84-HUD, Mobile Home
Approved.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the UL1482, (UM)
84-HUD and NPFA211 in the U.S.A. and the ULC S628-93 and
CAN/CSA-B365 Installation Codes in Canada.
• The structural integrity of the mobile home floor, ceiling, and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and
chimney must be listed to UL103 HT or a listed UL1777 full length six inch (152mm) diameter liner must
be used.
• Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
D. Glass Specifications
This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
B. BTU & Efficiency Specifications
EPA Certification #: 714
EPA Certified Emissions: 2.3 grams per hour
*LHV Tested Efficiency: 77.9 %
WARNING
**HHV Tested Efficiency: 72.1 %
***EPA BTU Output: 11,100 to 40,400 / hr.
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided by,
the following actions:
****Peak BTU/Hour Output: 76,200
Vent Size: 6 inches
Firebox Size: 2.98 cubic feet
Maximum Wood Length: 24 inches
Ideal Wood Length: 22 inches
Fuel Seasoned Cord Wood
* Weighted average LHV efficiency using Douglas Fir dimensional lumber and data collected during EPA emissions test.
**Weighted average HHV efficiency using Douglas Fir dimensional lumber and data collected during EPA emissions test.
***A range of BTU outputs based on EPA Default Efficiency and
the burn rates from the low and high EPA tests, using Douglas
Fir dimensional lumber.
****A peak BTU out of the unit calculated using the maximum first
hour burn rate from the High EPA Test and the BTU content of
cordwood (8600) times the efficiency.
The Quadra-Fire 5700 Series Wood Stove (ACC) meets the
U.S. Environmental Protection Agency’s crib wood emission
limits for wood heaters sold after May 15, 2015.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
May 4, 2015
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved by
Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with unit).
• Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
Quadra-Fire is a registered trademark of Hearth & Home
Technologies.
7038-207D
7
5700 STEP TOP ACC
2
User Guide
Operating Instructions
A. Over-Firing Your Appliance
to keep the chimney hot for as long as it takes to dry the
wood out - about one hour. It is a waste of energy to burn
unseasoned wood of any kind.
WARNING
Fire Risk
Do not over-fire.
Over-firing may ignite creosote or will damage the
stove and chimney.
To prevent over-firing your stove, DO NOT:
• Use flammable liquids
• Overload with wood
• Burn trash or large amounts of scrap lumber
• Permit too much air to the fire
1. Symptoms of Over-Firing
Symptoms of over-firing may include one or more of the
following:
• Chimney connector or appliance glowing
Dead wood lying on the forest floor should be considered wet,
and requires full seasoning time. Standing dead wood can
be considered to be about 2/3 seasoned. To tell if wood is
dry enough to burn, check the ends of the logs. If there are
cracks radiating in all directions from the center, it is dry. If
your wood sizzles in the fire, even though the surface is dry,
it may not be fully cured.
Splitting wood before it is stored reduces drying time. Wood
should be stacked so that both ends of each piece are
exposed to air, since more drying occurs through the cut ends
than the sides. This is true even with wood that has been
split. Store wood under cover, such as in a shed, or covered
with a tarp, plastic, tar paper, sheets of scrap plywood, etc.,
as uncovered wood can absorb water from rain or snow,
delaying the seasoning process.
• Roaring, rumbling noises
C. Burning Process
• Loud cracking or banging sounds
• Metal warping
• Chimney fire
2. What To Do if Your Stove is Over-Firing
• Immediately close the door and air controls to reduce
air supply to the fire.
• If you suspect a chimney fire, call the fire department
and evacuate your house.
• Contact your local chimney professional and have your
stove and stove pipe inspected for any damage.
• Do not use your stove until the chimney professional
informs you it is safe to do so.
Hearth & Home Technologies WILL NOT warranty stoves
that exhibit evidence of over-firing. Evidence of over-firing
includes, but is not limited to:
• Warped air tube
• Deteriorated refractory brick retainers
• Deteriorated baffle and other interior components
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover, out
of the rain and snow. Dry and well-seasoned wood will not
only minimize the chance of creosote formation, but will give
you the most efficient fire. Even dry wood contains at least
15% moisture by weight, and should be burned hot enough
8
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order to
improve the situation, we at Quadra-Fire have developed
cleaner-burning wood stoves that surpass the requirements
for emissions established by our governing agencies. These
wood stoves, like any other appliances, must be properly
operated in order to insure that they perform the way they are
designed to perform. Improper operation can turn most any
wood stove into a smoldering environmental hazard.
1. Kindling or First Stage
It helps to know a little about the actual process of burning in
order to understand what goes on inside a stove. The first
stage of burning is called the kindling stage. In this stage, the
wood is heated to a temperature high enough to evaporate the
moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat from
the coals and tends to cool the appliance.
Fire requires three things to burn - fuel, air and heat. So, if
heat is robbed from the appliance during the drying stage, the
new load of wood has reduced the chances for a good clean
burn. For this reason, it is always best to burn dry, seasoned
firewood. When the wood isn’t dry, you must open the air
controls and burn at a high burn setting for a longer time to
start it burning. The heat generated from the fire should be
warming your home and establishing the flue draft, not evaporating the moisture out of wet, unseasoned wood, resulting
in wasted heat.
7038-207D
May 4, 2015
5700 STEP TOP ACC
2. Second Stage
The next stage of burning, the secondary stage, is the period
when the wood gives off flammable gases which burn above
the fuel with bright flames. During this stage of burning it is
very important that the flames be maintained and not allowed
to go out. This will ensure the cleanest possible fire. If the
flames tend to go out, it is set too low for your burning conditions. The air control located at the upper right hand corner
is used to adjust for burn rates. This is called the Burn Rate
Air Control. Figure 9.1.
3. Final Stage
The final stage of burning is the charcoal stage. This occurs
when the flammable gases have been mostly burned and only
charcoal remains. This is a naturally clean portion of the burn.
The coals burn with hot blue flames.
The second function of the Start-Up Air Control is operation
of the rear air system. The rear air is used primarily during
a High Burn Rate. However, in some instances rear air is
desired during normal operation to help with combustion of
fuel towards the back of the firebox particularly when burning
hardwoods. The rear air is controlled independently from the
ACC system. Slide the Start-Up Air Control between the first
and third marker as indicated on the label to allow rear air to
enter the firebox. Figure 9.1.
2. Manual Timer Over-Ride
If you need to shut the ACC system off before it shuts itself
off after 25 minutes (i.e. overfire situation), reach down to
the bottom right rear corner and pull the lever toward you.
Figure 9.2.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of heat
needed to dry and rekindle the next load of wood. It is best
to open the Burn Rate Air and Start-Up Air Controls before
reloading. This livens up the coalbed and reduces excessive
emissions (opacity/smoke). Open door slowly so that ash or
smoke does not exit appliance through opening. You should
also break up any large chunks and distribute the coals so
that the new wood is laid on hot coals.
HIGH
Burn Rate
Air Control
MED
LOW
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To do
this we need to learn to burn our stoves in the cleanest way
possible. Doing this will allow us to continue using our wood
stoves for many years to come.
D. Automatic Combustion Control (ACC)
Typically, when you build a fire, you open the air controls fully
and monitor the fire to prevent it from going into an overfire
situation and/or burning your wood up too quickly before you
shut down the air controls to the desired burn rate. With the
Automatic Combustion Control (ACC) system, you do not
have to continually monitor the fire. Once you set the ACC
system it will control the fire for you. Follow the instructions
below to learn how to operate your stove with ease.
Start-Up
Air Control
Figure 9.1
E. Air Controls
1. Start-Up Air Control
The Start-Up Air Control has two primary functions. The
first function is to activate the Automatic Combustion Control
system (ACC). This function is performed by sliding the control all the way back until it stops at the “HI” indicator on the
label and then pulling forward to the front of the stove until
it stops. This activates the ACC system and opens the front
air channel and allows air to enter the front of the stove for
approximately 25 minutes. The front air channel gradually
shuts down until it is completely closed at the end of the 25
minutes. The fire is now controlled by the air supplied by the
Burn Rate Air Control. This function should be performed
each time you reload the stove. Figure 9.1.
May 4, 2015
Pull Forward
to Shut Down
Manual
Timer (ACC)
Shut Down
Figure 9.2
7038-207D
9
5700 STEP TOP ACC
Start-Up Air Control all the way back until it stops (HI
marker) and then pull forward until it stops. This activates
the timer system (ACC).
2. Burn Rate Air Control
This air supply enters at the upper front of the firebox, near
the top of the glass door. This preheated air supplies the
necessary fresh oxygen to mix with the unburned gases,
helping to create second, third and fourth combustions. This
air is regulated by the Burn Rate Air Control. There are four
settings High, Medium-High, Medium-Low and Low. When
the control is raised all the way up it is on the High setting and
when pushed all the down it is on the Low setting. Figure 10.1.
F. Burn Rates and Operating Efficiency
This wood heater has a manufacturer-set minimum low
burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise operate this wood
heater in a manner inconsistent with operating instructions
in this manual.
4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr
Raise the Burn Rate Air Control up to the bottom of the
middle marker and stop. Slide the Start-Up Air Control
all the way back until it stops (HI marker) and then pull
forward until it stops. This activates the timer system
(ACC).
5. Low Burn Rate - Below 10,000 BTU/hr
Leave the Burn Rate Air Control at the bottom marker.
Slide the Start-Up Air Control all the way back until it
stops (HI marker) and then pull forward until it stops. This
activates the timer system (ACC).
For maximum operating efficiency
HIGH
Shown with Side
Shield Removed
1. This appliance has a timer system (ACC) that operates
the stove at its maximum efficiency removing any guess
work for the homeowner. Follow the instructions below
for each burn rate for the Start-Up Air Control and Burn
Rate Air Control. Figure 10.1.
LOW
2. Burn dry, well-seasoned wood.
Burn Rates
Low (Closed)
High (Open)
1. Starting a Fire and Reloading
Open both controls fully by raising the Burn Rate Air
Control all the way up until it stops and slide the Start-up
Air Control back until it stops. After loading the stove with
wood and starting the fire, set both controls to the desired
setting by following the burn rate instructions below.
Burn Rate
Air Control
Front Air Channel
Operated by Timer
NOTE: These are approximate settings, and will vary with
type of wood or chimney draft. Due to altitude and other
environmental circumstances, this operational information is
a guideline only.
Start-Up Air
Control
Timer
Rear Air Channel
Operates independently
from Timer
Timer Manual
Shut-off
2. High Burn Rate - Maximum Heat - 30,000+ BTU/hr
Raise the Burn Rate Air Control all the way up until it stops
(top marker) to a fully open position. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and leave
it there. This setting over-rides the timer system (ACC)
so you must monitor the fire closely while in this setting.
START-UP
REAR AIR
HI
WARNING
Risk of Fire.
When set on High Burn Rate and over-riding the Automatic Combustion Control system an overfire situation
can occur and could result in a chimney fire.
Overfiring will void the stove warranty.
3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr
Raise the Burn Rate Air Control all the way up until it
stops (top marker) to a fully open position. Slide the
10
Closed
Wide
Open
“HI” setting
over-rides
Timer
After activating the timer (ACC), if the control is placed
within the rear air section on the label it will allow rear air
to enter the firebox. This will not interfere with the timer
gradually closing the front air channel in 25 minutes. If
control is set on “HI” it over-rides the timer (ACC).
Figure 10.1
7038-207D
May 4, 2015
5700 STEP TOP ACC
NOTE: Operate appliance on High Burn 15 minutes a
Baffle Board & Blanket even
with front tube & resting on all
tubes
day to help keep flue/chimney clean.
G. Building A Fire
Before lighting your first fire in the stove:
1. Confirm the baffle is correctly positioned. It should be
even with the front tube and resting on all tubes. Figure
11.1.
Burn Rate
Air Control
2. Follow instructions on page 17 for cleaning plated surfaces, if applicable.
3.
Remove all labels from glass.
Start-Up
Air
Control
There are many ways to build a fire. The basic principle is
to light easily-ignitable tinder or paper, which ignites the fast
burning kindling, which in turn ignites the slow-burning firewood. Here is one method that works well:
1. Open the Burn Rate Air and Start-Up Air Controls fully.
Ceramic Blanket on Top
2. Place several wads of crushed paper on the firebox floor.
Heating the flue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles are in
the immediate area of the appliance. Be sure the room
is adequately ventilated and the flue unobstructed.
5. Light the paper in the appliance. NEVER light or rekindle
fire with kerosene, gasoline, or charcoal lighter fluid; the
results can be fatal.
6. Once the kindling is burning quickly, add several full-length
logs 3 inches (76mm) or 4 inches (102mm) in diameter.
Be careful not to smother the fire. Stack the pieces of
wood carefully; near enough to keep each other hot, but
far enough away from each other to allow adequate air
flow between them.
Tube Channels
Figure 11.1
WARNING
Fire Risk
Do NOT store wood:
• Closer than required clearances to combustibles to
appliance
• Within space required for loading or ash removal.
7. Set the Burn Rate Air Control and activate the timer
system (ACC).
8. When ready to reload, It is best to fully open both the Burn
Rate Air and Start-up Air Controls before reloading. This
livens up the coalbed and reduces excessive emissions
(opacity/smoke). Open door slowly so that ash or smoke
does not exit appliance through opening. Large logs burn
slowly, holding a fire longer. Small logs burn fast and hot,
giving quick heat.
Do NOT operate appliance:
• With appliance door open.
• With ash removal system door open.
WARNING
9. As long as there are hot coals, repeating steps 6 through
8 will maintain a continuous fire throughout the season.
Fire Risk.
• Do NOT burn wet or green wood.
• Store wood in dry location.
• Stack wood so both ends are exposed to air.
Wet, unseasoned wood can cause accumulation of
creosote.
NOTE:
• Build fire on brick firebox floor.
• Do NOT use grates, andirons or other methods to support fuel.
It will adversely affect emissions.
CAUTION
CAUTION
To prevent damages, do not stack burnables against glass.
May 4, 2015
2 pc Baffle Board
Do not leave door open during normal operation (except for
re-fuel).
7038-207D
11
5700 STEP TOP ACC
H. Correct Baffle & Blanket Placement
INCORRECT POSITIONS
WARNING
Fire Risk
Firebox damage due to improper baffle placement is not covered by warranty. Operate the
wood burning appliance with the baffle in the
correct position only.
Not doing so could result in:
• Reduced efficiency
• Overheating the chimney
• Overheating the rear of the firebox
• Poor performance
Ensure correct baffle placement and replace baffle components if damaged or missing.
Ceramic Blanket and Baffle Board are NOT in contact
with the back of the firebox.
CAUTION
The baffle boards are FRAGILE. Use extreme caution when
loading firewood to prevent:
• Cracking, breaking or damaging the baffle boards
DO NOT operate the stove without baffle boards
Ceramic Blanket is NOT in contact with the back of the
firebox and NOT even with the Baffle Board in the front.
CORRECT POSITION
Back of Firebox
Ceramic Blanket
Back of Firebox
Baffle Retainer Bracket
Ceramic Blanket
Baffle Board
Ceramic Blanket and Baffle Board MUST be in contact
with the back of the firebox and even with each other in
the front.
Figure 12.1
12
Baffle Board
Ceramic Blanket is bunched up at the back of the firebox
and NOT even with the Baffle Board in the front.
Figure 12.2
7038-207D
May 4, 2015
5700 STEP TOP ACC
I. Blower Operating Instructions
Down (Closed)
NOTE: If your Quadra-Fire wood stove is equipped with an
optional blower, you should follow these guidelines:
1. Initial (cold) startup: Open both controls fully by raising the Burn Rate Air Control all the way up until it stops
and slide the Start-up Air Control back until it stops. The
blower tends to cool the appliance. Leave the blower off
until the burn is well established, i.e., 30 minutes.
Up (Open)
Burn Rate
Air Control
2. High Burn Setting: Both controls are open. Burn Rate
Air Control is pulled up and the Start-up Air Control is fully
pushed in. Blower may remain on.
3. Medium or Medium High Burn Setting*: Burn Rate
Air Control is closed then opened to 1 inch to fully open.
Blower may remain on.
4. Medium Low Burn Setting*: Burn Rate Air Control is
closed then opened to 1/4 inch to 1/2 inch. Leave the
blower off until the burn is well established, i.e., 30 minutes.
Start-Up Air
Control
Push to Open
Pull back to
activate ACC
Figure 13.1
5. Low Burn Setting*: Burn Rate Air Control is closed.
Leave the blower off until the burn is well established, i.e.,
30 minutes.
*NOTE: For burn settings 3 to 5 the Start-up Air Control
needs to be pushed in (Open) then pulled back to activate the Automatic Combustion Control (ACC).
NOTE: For maximum efficiency and lowest emissions,
when operating the blower in either the automatic or
manual setting for the low and medium low burn settings
leave the blower off until the burn is well established, i.e.,
30 minutes
6. The blower is equipped with a rheostat (speed control).
The highest blower speed is obtained by turning the
rheostat on, then adjusting back towards “OFF” as far as
possible without turning the blower off. For a low blower
speed, turn the control knob clockwise as far as possible
7.
Figure 13.2
Snap Disc Location
If you find the blower coming on and off at undesirable
temperatures, relocate the snap disc to another location
in the designated zone on the back of the appliance.
Figure 13.2. There is a manual over-ride switch to
deactivate the snap disc, if necessary.
J. Opacity (Smoke)
This is the measure of how cleanly your appliance is burning. Opacity is measured in percent; 100% opacity is when
an object is totally obscured by the smoke column from a
chimney, and 0% opacity means that no smoke column can
be seen. As you become familiar with your appliance, you
should periodically check the opacity. This will allow you to
know how to burn as nearly smoke-free as possible (goal of
0% opacity).
May 4, 2015
CAUTION
When burning your first fire, you will experience smoke
and odor from the appliance resulting from the curing
of paint and burning off of any oils remaining from
manufacturing.
OPEN WINDOWS DURING INITIAL BURN TO
DISSIPATE SMOKE AND ODORS!
• Odors may be irritating to sensitive individuals.
• Smoke detectors may activate.
7038-207D
13
5700 STEP TOP ACC
K. Clear Space
•
Do NOT place combustible objects within 4 ft (1.2 m) of
the front of appliance. See Figure 14.1.
•
Mantel - avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these
objects.
Maintain 4 ft (1.22m) clearance to
combustible in front of appliance
WARNING
DO NOT PLACE COMBUSTIBLE OBJECTS IN FRONT
OF THE APPLIANCE. High temperatures may ignite
clothing, furniture or draperies.
Figure 14.1
L. Frequently Asked Questions
ISSUES
SOLUTIONS
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Whirring sound
If the optional blower has been installed, the blower produces a whirring sound which
increases in volume as the speed is increased.
CONTACT YOU DEALER for additional information regarding operation and troubleshooting.
Visit www.quadrafire.com to find a dealer.
WARNING
WARNING
Fire Risk.
Keep combustible materials, gasoline and other
flammable vapors and liquids clear of appliance.
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPTHA OR
ENGINE OIL.
• Do NOT store flammable materials in the appliance’s vicinity.
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monoxide if burn material other than
wood.
May result in illness or possible death.
• DO NOT USE GASOLINE, LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID OR SIMILAR LIQUIDS TO
START OR “FRESHEN UP” A FIRE IN THIS HEATER.
• Keep all such liquids well away from the heater while it is in
use.
• Combustible materials may ignite.
14
7038-207D
May 4, 2015
5700 STEP TOP ACC
3
Maintenance and Service
A. Quick Reference Maintenance Guide
CAUTION!
When properly maintained, your fireplace will give you
many years of trouble-free service. Contact your dealer to
answer questions regarding proper operation, troubleshooting and service for your appliance. Visit www.quadrafire.
com to find a dealer
Allow the appliance to completely cool
down before performing any cleaning or maintenance.
Start the first inspection after the first 2 months of use, or if
performance changes, and adjust your schedule accordingly. Maintenance is required for safe operation and must be
performed to maintain your warranty.
Frequency
Baffle & Blanket
Blanket
MONTHLY
or
After Every
Cord of Wood
Baffle and blanket placement is critical to
heat output, efficiency and overall life of
the unit. Make sure the baffle is pushed all
of the way to the back of the firebox and
the blanket is laying flat. Inspect baffle for
cracks.
YEARLY
or
After Every
4 Cords of
Wood
Vacuum the blower impellers.
Baffle
Optional Blower
Chimney System
Task
EVERY 2
MONTHS
or
After Every
4 Cords of
Wood
The chimney and chimney cap must be inspected for soot and creosote every two
months during the burn season or more
frequency if chimney exceeds or is under 1416 ft (4.3m-4.8m) measured from bottom of
appliance.
This will prevent pipe blockage, poor draft,
and chimney fires.
Always burn dry wood to help prevent cap
blockage and creosote build-up.
Firebrick & Ash Removal
Door & Glass Assemblies
Door Handle
Latch Cam
Door Cross Section
(example)
Locknut
Spring
Handle
Door Handle
Spacing
Washers
WEEKLY
or
After Every
25 Loads of
Wood
Ashes must be cool before you can dispose
of the ashes in a non-combustible container.
WEEKLY
or
After Every
25 Loads of
Wood
Keep door and glass gasket in good shape
to maintain good burn times on a low burn
setting. To test: place a dollar bill between the
stove and door and then shut the door. If you
can pull the dollar out, remove one washer
from door handle behind latch cam and try
again. If you can still pull it out, replace the
door gasket.
Check the glass frame for loose screws to
prevent air leakage. Check glass for cracks.
WEEKLY
or
After Every 25
Loads of Wood
Check the door latch for proper adjustment.
This is very important especially after the door
rope has formed to the stove face.
Square Key
Firebrick is designed to protect your firebox.
After ashes are removed, inspect the firebrick and replace firebricks that are crumbling, cracked or broken.
Check door handle for smooth cam operation.
These are generic drawings and may not represent your model.
May 4, 2015
7038-207D
15
5700 STEP TOP ACC
2. Ash Removal System (ARS) Operating and Cleaning
B. General Maintenance
1. Creosote (Chimney) Cleaning
•
•
Frequency: Every 2 months during heating season or
as recommended by a certified chimney sweep; more
frequently if chimney exceeds or is under 14-16 ft.
(measured from bottom of appliance)
By: Certified Chimney Sweep
Remove all ash from the firebox and extinguish all hot embers
before disposal. Allow the appliance to cool completely.
Disconnect flue pipe or remove baffle and ceramic blanket
from appliance before cleaning chimney. Otherwise residue
can pile up on top of the baffle and ceramic blanket and
the appliance will not work properly. (See Baffle Removal
on page 20). Close the door tightly. The creosote or soot
should be removed with a brush specifically designed for
the type of chimney in use. Clean out fallen ashes from the
firebox.
•
•
Frequency: As necessary
By: Homeowner
a. The stove and ashes must be completely cooled down
before using the Ash Removal System. Reach down and
locate the ash removal door handle under the left side of
the stove in the center. Squeeze the handle and push all
the way back. A magnet will hold the handle in place which
in turn holds the ash door open.
b. Clean ash down through the ash removal system grate into
the drawer below. If there are large pieces in the ashes,
you can remove the grate before brushing the ash into the
drawer.
Make sure all ash is removed from the top of ARS door.
Lift up the grate and inspect the top of the door to ensure
all ash has been removed. You can rapidly move the ARS
latch handle up and down to help remove any ash from the
door. Use a small brush to clean off the top of the door if
any ash remains.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build creosote
deposits quicker, so it is important to check the chimney from
the top as well as from the bottom.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which combine
with expelled moisture to form creosote.
Be sure to replace the grate before operating the stove.
Remember to leave 1/4 to 1/2 inch (6-13mm) of ash on the
firebox floor to act as a natural grate, allowing air to flow
freely underneath wood.
c. Close the door handle, you will hear a “click” when it closes.
The ash drawer will not pull out if the door handle is left in
the open position. Wear gloves to remove the drawer.
Dispose of the ashes following the directions on the next
page.
The creosote vapors condense in the relatively cool chimney flue
of a newly-started or a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. When ignited, this
creosote creates an extremely hot fire which may damage the
chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to determine
if a creosote or soot buildup has occurred. If creosote or soot
has accumulated, it should be removed to reduce the risk of a
chimney fire.
WARNING
Fire Risk
Injury Risk
Make sure Ash Removal System door is sealed tight
against the gasket.
Air leakage may cause:
• Over-fire condition.
• Flame and/or smoke spillage.
• Wood to burn too fast.
WARNING
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and chimney once
every two months during heating season.
Injury Risk.
• Gloves recommended
• Remove creosote to reduce risk of chimney fire.
• May have sharp edges
CAUTION
• Ignited creosote is extremely HOT.
WARNING
Fire Risk.
Do not use chimney cleaners or flame colorants in
your appliance. Will corrode pipe.
16
7038-207D
May 4, 2015
5700 STEP TOP ACC
3. Disposal of Ashes
•
•
Frequency: When ash is within 1-3/4 in. (44mm) of firebox
lip
By: Homeowner
Operating the appliance with the Burn Rate Air Control and
Start-Up Air Control all the way open for 15-20 minutes should
remove the built up coating.
Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed
on a non-combustible floor or on the ground, well away
from all combustible materials, pending final disposal. If
the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
WARNING
Fire Risk.
Disposal of Ashes
• Ashes should be placed in metal container with tight fitting lid.
• Do not place metal container on combustible surface.
• Ashes should be retained in closed container until all cinders
have thoroughly cooled.
4. Cleaning Plated Surfaces
•
•
Frequency: Prior to first burn and then as desired
By: Homeowner
Clean all the fingerprints and oils from plated surfaces
BEFORE firing the appliance for the first time. If not
cleaned properly before lighting your first fire, the oils
can cause permanent markings on the plating.
After the plating is cured, the oils will not affect the
finish and little maintenance is required. Wipe clean as
needed.
CAUTION
• Do not use polishes with abrasives. It will scratch plated
surfaces.
5. Glass Cleaning
•
•
Frequency: As desired
By: Homeowner
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed by
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven
cleaner left on during the next firing can permanently stain
the glass and damage the finish on plated metal surfaces.
A portion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes”
the glass, helping to keep smoke from adhering to its surface.
When operated at a low burn rate, less air will be flowing over
the glass and the smoky, relatively cool condition of a low fire
will cause the glass to become coated.
May 4, 2015
7038-207D
17
5700 STEP TOP ACC
4
Troubleshooting Guide
With proper installation, operation, and maintenance your wood stove will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist you or a qualified service person in the diagnosis of a problem
and the corrective action to be taken.
Start Fire Problems
Possible Cause
Solution
Can not get fire started
Excessive smoke or spillage
Burns too slowly
Not enough heat output
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange kindling &
wood for air movement.
Check for restricted termination cap
Check for blockage of outside air kit (if installed).
Check for flue blockage.
Not enough air for fire to ignite
Pre-warm flue before starting fire (refer to Building
a Fire Section).
Check for adequate vent height (refer to Chimney
Height Section).
Open window below the appliance towards the
wind.
Wood condition is too wet, too
large
Use dry, seasoned wood (refer to Seasoned Wood
Section).
Bed of coals not established
before adding wood
Start with paper & kindling to establish bed of
coals (refer to Building a Fire Section).
Flue blockage such as birds’
nests or leaves in termination
cap
Have chimney inspected for creosote and cleaned
by a certified chimney sweep.
Down draft or negative pressure
Competition with exhaust
devices
Do not use exhaust fans during start-up (refer to
Negative Pressure Section).
Fire burns too fast
Mix in hardwood.
Extremely dry or soft wood
Mix in less seasoned wood after fire is established
(refer to Wood Fuel Section).
Check for correct vent height; too much vertical
height creates overdrafting.
Overdrafting
18
Open window below the appliance towards the
wind.
Check location of vent termination (refer to
Chimney Termination Requirement Section).
7038-207D
May 4, 2015
5700 STEP TOP ACC
5
Service Part Replacement
A. Glass Replacement
B. Snap Disc Replacement
1.
Ensure that the fire is out and the appliance is cool to the
touch.
2.
Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent injury.
3.
Remove the door with the broken glass by lifting the door
up and off of the hinges.
4.
Lay door face down on a table or counter making sure the
handle hangs over the edge so the door lays flat, on a soft
surface.
5.
Remove the screws from each glass retainer and remove
the glass. (If screws are difficult to remove, soak with
penetrating oil first).
6.
Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and
right sides).
7.
Replace the glass retainers. Be careful not to cross thread
the screws.
8.
Tighten each retainer just a few turns until each is
secured. Check again for centering of glass in door
frame. Continue to tighten each retainer alternately, a
few turns at a time, until the glass is secure. DO NOT
OVERTIGHTEN.
9.
Replace the door on the appliance.
1. Disconnect power supply. Locate the snap disc bracket
assembly at the bottom left rear corner of the appliance.
Figure 20.1.
2. A magnet holds the bracket to the appliance. Pull the
bracket down away from the appliance to expose the snap
disc.
3. Pull the snap disc and spade connectors up and out of
bracket as shown in Figure 20.2.
4. Using a Phillips head screw driver, remove the 2 screws
from the snap disc and then remove the snap disc from
the spade connectors. Replace with new snap disc and
re-connect to spade connectors.
5. Push the snap disc and spade connectors back inside
bracket and re-attach the bracket to the appliance.
Snap Disc Location
Quadra-Fire stoves are equipped with ceramic super heatresistant glass, which can only be broken by impact or
misuse. Do not slam stove door or impact the glass. When
closing door, make sure that logs do not protrude against the
glass. Inspect glass regularly. If you find a crack or break,
immediately put the fire out and return the door to your dealer
for replacement of glass before further use.
Figure 20.1
Snap Disc
CAUTION!
Handle glass assembly with care.
Glass
Assembly
•
•
•
•
•
Magnet
When cleaning glass:
• Avoid striking, scratching or
slamming glass.
Spade
Connectors
Figure 20.2
Do NOT clean glass when hot.
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Use commercial oven cleaner on heavier deposits.
Remove all residue of oven cleaner or will permanently stain
glass on next firing. Refer to maintenance instructions.
WARNING
Injury Risk.
• Use only glass specified in manual.
• DO NOT REPLACE with any other material.
May 4, 2015
7038-207D
19
5700 STEP TOP ACC
D. Firebrick Replacement
C. Baffle Removal
1.
Remove all ash from the firebox, and extinguish all hot
embers before disposal into a metal container.
2.
The baffle board has 2 pieces. With the ceramic blanket
still in place, slide one baffle piece over the top of other
one and pull out top piece through the door opening and
then remove bottom baffle piece. Figure 20.1.
3.
Remove the ceramic blanket.
4.
Re-install the ceramic blanket and smooth out the blanket.
4.
Slide the baffle pieces one piece at a time underneath the
blanket. Be sure the baffle boards are even with the front
manifold tube and is resting on all tubes. Figures 20.1 and
20.2.
Replace the firebrick if they become crumbly and/or if there
is a 1/4 inch (6.35mm) gap between the bricks.
Inspect the firebrick after each ash removal.
The firebox is lined with high quality firebrick, which has
exceptional insulating properties. There is no need to use a
grate; simply build a fire on the firebox floor. Do not operate
appliance without firebrick.
1. After the coals have completely cooled, remove all old
brick and ash from unit and vacuum firebox.
2. Remove new brick set from box and lay out to diagram
shown.
3. Lay bottom bricks in unit.
4. Install rear bricks on the top of the bottom bricks. Slide
top of bricks under clip on back of firebox wall and push
bottom of brick back.
5. Install side bricks. Slide top of brick under clips on side
of firebox and push the bottom of the brick until it is flush
with the side of the appliance.
Use Part 832-0550 when ordering individual brick. Provide brick
dimension from the service parts list at the end of this manual , mark
the desired brick and take it to your authorized dealer.
E. Door Handle Assembly
Figure 20.1
1. Install washer on door handle shaft.
2. Slide door handle through door.
Baffle Board & Blanket even
with front tube & resting on all
tubes
3. Install second washer(s) as shown in Figure 20.3.
4. Install key in groove.
5. Align groove in latch cam with key; slide latch cam over
shaft
Burn Rate
Air Control
Start-Up
Air
Control
6. Install locknut but do not overtighten, the handle needs
to move smoothly.
7. Install spring handle turning in a counter-clockwise
motion to desired location on door handle rod. Figure
20.3.
CAUTION
Do not overtighten lock nut. The door handle needs to
move smoothly.).
Ceramic Blanket on Top
atch
am
Door ross Section
(example)
ocknut
Spring
andle
Door
Tube Channels
Figure 20.2
20
andle
Spacing
Washers
2 pc Baffle Board
S uare ey
Figure 20.3
7038-207D
May 4, 2015
5700 STEP TOP ACC
F. Tube Channel Assembly Replacement
Removing Tube Channel Assembly
1. Remove the right side shield by removing 2 screws in the
back using a Phillips head screw driver.
NOTE: Service Space
2. Remove 4 screws from channel access cover and remove
cover.
In order to replace the tube channel assembly a clearance
of 19 inches (483mm) is required on the right side of stove
in order to remove the tubes with the stove in place.
3. Locate 2 channel nuts inside of chamber and remove
using a 7/16 socket wrench. Slide out tube channel
assembly.
NOTE:
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.
Soak the bolts with penetrating oil for at least 15
minutes before trying to remove them.
Replacing Tube Channel Assembly
1. Slide one gasket onto each tube.
2. Slide the tube channel assembly into side of firebox and
insert each tube into the corresponding hole in the tube
channel rack starting with the back hole first.
3. Make sure tube channel assembly is flush against the
side of the stove and secure with channel nuts.
4. Re-install channel cover and side shield.
Tube Channel Nuts
1
Tube Channel Assembly
Bolt
2
3
Right Side
Rear Brick
Side Brick
6
4
1
Rotate and
remove from
firebox
1
1
1
4
Baffle Boards
Brick Retainers
Ceramic Blanket
Baffle Protection Channel
Figure 21.1
May 4, 2015
7038-207D
21
5700 STEP TOP ACC
6
Reference Materials
A. Service & Maintenance Log
Date of Service
22
Performed By
Description of Service
7038-207D
May 4, 2015
5700 STEP TOP ACC
B. Service Parts & Accessories
R
57ST-ACC
Service Parts
Beginning Manufacturing Date: April 2009
Ending Manufacturing Date: Active
Step Top Wood Stove
Advanced Combustion Control
3
1
2
4
5
28
6
7
8
10
9
27
26
11
22
25
12
23
13
24
21
16
20
14
19
15
18
17
Part number list on following page.
04/15
May 4, 2015
7038-207D
23
5700 STEP TOP ACC
R
57ST-ACC
Service Parts
Beginning Manufacturing Date: April 2009
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
1
2
DESCRIPTION
COMMENTS
Air Channel, Convection
Stocked
at Depot
PART NUMBER
SRV7038-127
Air Supply Back
SRV7038-119
3
Panel Assembly Side, Left
SRV7038-006
4
Blanket, Ceramic Fiber
SRV7038-117
5
BafÀe Protection Channel (illustration on page 5)
SRV7038-179
6
BafÀe Board
7
Rear Channel Assembly
8
Access Cover - ARS
SRV7038-196
9
Channel - Ash Removal System (ARS)
7033-172
10
Tube Channel Rack
SRV7038-174
Qty: 2
SRV7038-118
Y
SRV7038-001
11
Tube Channel Assembly
SRV7038-008
12
Secondary Tube Gasket
7038-187
13
Door Assembly
Black
DR-57BK-FH
Nickel Trim
DR-57NL-FH
Y
Qty: 2 Gold
832-0250
Qty: 2 Nickel
430-5320
Qty: 1 Gold
832-0620
Y
Qty: 1 Nickel
250-8330
Y
Glass Assembly
7000-014
Y
Glass Frame Set
GLA-FRM-5700
14
Hinge Pins, 1/2”
15
Spring Handle, 1/2”
16
Gasket, Glass Tape, 3/4 “ - Field Cut to Size
5 Ft
832-0460
Rope, Door, 3/4” x 84” - Field Cut to Size
7 Ft
832-1680
Gold
200-3180
Nickel
200-3240
Black & Gold Doors
436-5350
Logo, Quadra-Fire
Component Pack (Includes Nickel Spring Handles (1) 1/2” &
(2) 1/4”, (2) Nickel Hinge Pins, Quadra-Fire Logo)
Door Handle Assemblies
Nut, Locking (For Door Handle)
17
Y
Nickel Doors
436-5360
Spring Handle
832-0540
Fiber Handle
SRV7033-071
Pkg of 24
226-0100/24
Handle Assembly
472-5130
Cam Latch
430-1141
Key, Cam Latch
430-1151
Y
Y
Y
Screw, Flat Head Philips 8-32 x 1/2
Pkg of 10
832-0860
Y
Washer, Sae, 3/8
Qty: 3 ea.
832-0990
Y
Qty: 4
SRV7038-145
Brick Retainer, Side
Label, Burn Rate Air Control
7033-160
Label, Start-Up Air Control
7033-166
Additional service part numbers appear on following page.
24
7038-207D
May 4, 2015
5700 STEP TOP ACC
R
57ST-ACC
Service Parts
Beginning Manufacturing Date: April 2009
Ending Manufacturing Date: Active
#18 Brick Set
18.5
18.8
18.8
18.4
18.1
18.8
18.1
18.8
18.1
18.1
18.1
18.7
18.6
18.6
18.2
18.1
CoNo B
ve ri
r L ck
oc , A
ati RS
on
18.6
18.1
18.1
18.1
18.1
18.7
18.1
18.6
18.3
18.1
18.4
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers.
Stocked
at Depot
Provide model number and serial number when requesting service parts from your dealer or
distributor.
ITEM
18
DESCRIPTION
COMMENTS
Brick Assembly - Complete Set
Pkg of 27
18.1
Brick, 9 x 4.5 x 1.25”
Qty. 12 Req.
18.2
Brick, 9 x 1.75 x 1.25”
Qty. 1 Req.
18.3
Brick, 6.75 x 1.75 x 1.25”
Qty. 1 Req.
18.4
Brick, 9 x 2.75 x 1.25”
Qty. 2 Req.
18.5
Brick, 7 x 1.75 x 1.25”
Qty. 1 Req.
18.6
Brick, 6.75 x 4.5 x 1.25”
Qty. 4 Req.
18.7
Brick, 5 x 4.5 x 1.25”
Qty. 2 Req.
18.8
Brick, 7 x 4.5 x 1.25”
Qty. 4 Req.
Brick, Uncut
PART NUMBER
SRV7038-007
Qty: 1
832-0550
Qty: 6
832-3040
19
Brick Retainer, Rear
SRV7038-148
20
Panel Assembly Side, Right
SRV7038-005
23
Manifold Tube Cover
SRV7038-177
22
Secondary Air Diverter
SRV7038-186
21
Manifold Cover Plate
SRV7038-185
24
Oak Cover Plate Kit
SRV7038-024
25
Door Assembly - ARS
SRV7033-015
Y
26
Gasket - ARS
SRV7033-296
Y
27
Latch, Handle Assembly - ARS
SRV7033-047
Y
Additional service part numbers appear on following page.
May 4, 2015
7038-207D
25
5700 STEP TOP ACC
R
57ST-ACC
Service Parts
Beginning Manufacturing Date: April 2009
Ending Manufacturing Date: Active
#29 Pedestal Assembly
#28 Burn Rate Control
Assembly
#30 Legs Assembly
28.9
28.8
28.1
29.1
28.7
28.6
28.2
30.1
28.5
28.4
28.3
29.3
30.4
29.2
30.6
30.5
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
28.1
28.2
DESCRIPTION
COMMENTS
Burn Rate Control Assembly
PART NUMBER
SRV7038-025
Spring Handle, 1/4”
Qty: 2 Gold
832-0630
Y
Qty: 1 Nickel
250-8340
Y
28.3
Knob
7000-343
28.4
Air Control Rod Guide
7033-210
28.5
Latch, Magnet
229-0631
28.6
Control Arm Assembly Rear
SRV7038-004
28.7
Timer Door Control Arm Assembly
SRV7038-019
Door Gasket
7033-282
Y
28.8
Timer (Only) Replacement Assembly
SRV480-1940
Y
28.9
Timer Arm Assembly
7033-034
Y
29.1
Pedestal Kit
PED-5700
29.2
Ash Pan, Pedestal Model w/Door
29.3
SRV7038-010
Trim, Oak Strips
Qty: 2
Component Pack, Pedestal, Step-Top (Includes Gasket For Ash Removal, Magnet & Fasteners)
Black
Leg Kit & Ash Removal System (ARS)
No Longer Available
SRV472-0520
7033-045
LEG-3143-BK
LEG-3143-GD
Nickel
LEG-3143-NL
Qty: 2
SRV7038-028
30.1
Leg Adapter Set (Bracket), Left & Right
30.2
Ash Pan Door Handle
7033-274
Ash Pan Leg Assembly
7033-008
Ash Pan Leg - ARS
7033-050
30.3
Component Pack, Leg Step Top (Includes Gasket For Ash Removal, Magnet & Fasteners)
30.4
Legs, Queen Anne
7033-048
Qty: 4
831-1240
Qty: 4
831-1250
Qty: 4
LEGS-QANL
Additional service part numbers appear on following page.
26
7038-207D
May 4, 2015
5700 STEP TOP ACC
R
57ST-ACC
Service Parts
Beginning Manufacturing Date: April 2009
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Component Pack (Includes Touch-Up Paint, Owners
Manual, Warranty Card & Access Cover Handle)
PART NUMBER
SRV7038-017
Handle, Access Cover
SRV7038-197
Paint Touch-Up
812-0910
Upgrade, Door, Nickel
UK-DRNL
Gasket, Manifold
Pkg of 4
7038-168/4
Y
Side view
Front looking into unit
Ceramic blanket
Fiber baffle
Baffle protection channel sits in
between front tube and fiber
baffle
This tab sits behind the front tube
BafÀe Protection Channel
SRV7038-179
ACCESSORIES
Blower Assembly
BK-ACC
Blower Control Box W/Switch
SRV7000-194
Component Pack
7033-051
Y
Magnet Round
SRV7000-140
Snap Disc Bracket Assembly
7033-036
Snap Disc, # 1, Convection Blower
SRV230-0470
Y
Speed Control Only (Rheostat)
842-0370
Y
Wire Harness (Blower)
7033-262
Blower, Convection
Blower Only
Outside Air Kit, Floor & Rear
812-4900
Y
Y
OAK-ACC
Outside Air Collar Assembly
7033-039
Outside Air Shield
33271
Y
FASTENERS
Avk Rivnut Repair Kit - 1/4-20 & 3/8-16 Rivnut Tools
RIVNUT-REPAIR
Y
Nut, Ser Flange Small 1/4-20
Pkg of 24
226-0130/24
Y
Screw, Pan Head Philips 8-32 X 3/8
Pkg of 40
225-0500/40
Y
Screw, Sheet Metal #8 X 1/2 S-Grip
Pkg of 40
12460/40
Y
Washer, 1/4 Sae
Pkg of 24
28758/24
Y
May 4, 2015
7038-207D
27
CONTACT INFORMATION
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
log onto www.quadrafire.com
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating and • Read, understand and
follow these instrucmaintenance instructions for safe installations included.
tion and operation.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC O
AR T
D
We recommend that you record the following pertinent
information for your heating appliance.
Date purchased/installed:
Serial Number:
Location on appliance:
Dealership purchased from:
Dealer phone:
Notes:
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645, 7047962
or other U.S. and foreign patents pending.
28
7038-207D
May 4, 2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising