Philips Selecon Accent Beamshaper

Philips Selecon Accent Beamshaper
WARRANTY REGISTRATION: www.seleconlight.com/warrantyreg
Take full advantage of the Philips Selecon service commitment and register all
your new luminaires quickly and easily online for full after-sales support.
Philips Selecon Accent Beamshaper
**OPERATION MANUAL**
THIS INFORMATION IS DESIGNED TO PROVIDE YOU WITH THE INFORMATION
YOU NEED IMMEDIATELY UPON DELIVERY OF YOUR NEW LUMINAIRE.
If you require further assistance please contact your Philips Selecon dealer. www.seleconlight.com/distributors
Philips Selecon has packaged this product using environmentally friendly packaging. Please consider either
reuse of the packaging or dispose of responsibly with your nearest recycling collection agency.
IMPORTANT!
Read this manual carefully before attempting to install, operate or maintain the Accent Beamshaper. Follow the instructions in this manual.
Philips Selecon accepts no responsibility if the customer fails to do so.
For each customer, operating conditions will vary, sometimes greatly. Such variations may affect the luminaire‟s performance. Philips
Selecon has no control over the customer‟s unique operating environment. Hence, Philips Selecon makes no representations or warranties
concerning the luminaire‟s performance under the customer‟s actual operating conditions. All operating parameters must be validated for
each customer application by the customer‟s technical experts.
KEY OPERATING POINTS AND FEATURES
A: Beamshaper lid latch (Open this to insert
accessories and to clean the lenses)
C
B: Four non removable shutters. (These allow you to
mask portions of the beam, or to frame around pictures, etc.)
C: Shutter lock
D
A
H
D: Pattern/Gobo holder
E: Accessory slots - Various glass effects
and coloured glass can be used here*
F: Front Lens
G: Rear Lens
B
H: Lens focus knobs
E
G
F
*contact your Philips Selecon dealer for full details
www.seleconlight.com/distributors
MOUNTING YOUR BEAMSHAPER TO THE ACCENT SPOT
To insert the Accent Beamshaper push in the lid locking latch on the beamshaper
and open the lid. Insert the rear of the Beamshaper into the front slot provided on
the Accent Spot. Twist the beamshaper a quarter turn before closing the lid firmly
ensuring the lid locking latch „clicks‟ shut.
The Beamshaper can be rotated through 360 allowing positioning of the
shutters and the gobo/pattern holder in to any orientation.
Note: If the beamshaper is not twisted a quarter turn before closing the lid this
could cause the friction ring to be pinched and damaged.
JUNE 2012
© 2012 Philips Selecon All Rights Reserved
LAMPING UP
The Philips Accent Beamshaper is supplied with the recommended lamps as below.
BEAMSHAPER PART NUMBER
ACNTMHBS**
ACNTTHBS**
ACNTLEDBS**
DESCRIPTION
For use with CDM SPOT
For use with TH SPOT
For use with LED SPOT
LAMP SUPPLIED
No lamp
Inc GE 50W EXZ lamp
Inc Philips 10W 3000K LED lamp
** Add 01 for White and 03 for Black
To insert the lamp, push in the lid locking latch on the lamp housing and open the lid. Insert the lamp into the lamp base.
Once you have installed the lamp your luminaire should be ready for use.
Carefully read the manufacturer‟s instructions for safe lamp handling / use and disposal of used lamps. Replace with the
recommended lamp only. Spares are available from your Philips Selecon dealer: www.seleconlight.com/distributors
NOTE FOR LED LAMPS
Dimming performance of LED MR16 lamps can vary greatly on
different dimming systems, 100% compatibility cannot be
guaranteed. Dimmer loading for Philips MASTER LED 10W
lamp must be calculated based upon 50W per unit.
NOTE FOR CDM LAMPS
Due to colour shifts in new CDM MR16 lamps we recommend
that these lamps are run continuously for a minimum „burn-in‟
period of 20hrs prior to final installation.
FOCUSING THE BEAMSHAPER
The variable beam of your Accent Beamshaper is altered by adjusting the front and rear lens in relation to each other. To
move the lenses, simply loosen the lens locking knobs and move them into the desired position and then tighten the locking
knobs. The front lens defines the beam spread; the rear, the focus degree of softness or sharpness of the beam edge or
shutters. Finger tight pressure only is necessary to lock the lens off in its chosen position.
The four shutters can be used to mask off portions of the beam, or to frame areas, etc.
PATTERN USE
Pattern size: E
Outside diameter: 37.5mm
Image area: 28mm diameter
The Accent Beamshaper is supplied with an internal pattern holder.
To fit your pattern, remove the internal pattern holder from its
magnetic mounting plate. Unclip the locking plate and insert the
pattern with correct orientation. Re-clip the locking plate and place
the pattern holder back on the magnetic mounting plate.
For custom gobos please ensure the Design is inside the 28mm
area
SAFETY AND MAINTENANCE
Keep your Philips Selecon Accent Beamshaper in top condition and performing at its best by cleaning it regularly with a soft
cloth. The Beamshaper lenses should only be cleaned with optical tissue paper.
The above is the only maintenance task that can be safely carried out by non approved personnel.
Philips Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international
safety standards. It is your responsibility to maintain this luminaire in good and safe working condition.
Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with damaged lamps or cable,
etc. Consult your Philips Selecon distributor for assistance. Only replace damaged parts with authorised Philips Selecon
Accent spare parts.
LIMITED WARRANTY
Philips Selecon (“Selecon”) warrants all Philips Selecon luminaires against defects in materials or workmanship. The term of
this warranty is three years; from the date of delivery, and is dependant on the following operating conditions:
FOR ARCHITECTURAL DISPLAY: the Accent Beamshaper luminaire is used as a display light and in conditions typically
found in a museum being 10 to 12 hours daily, 7 days per week.
For full details of the Philips Selecon Warranty, please refer to our website: www.seleconlight.com
Australian customers - please refer to the Australia specific warranty card included with this product.
Manufacturer
Philips Selecon, 19-21 Kawana Street, Northcote, Auckland 0627, New Zealand
Ph: +64 9 481 0100, Fax: +64 9 481 0101
www.seleconlight.com
JUNE 2012
© 2012 Philips Selecon All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising