Modified specification for Mechanical Laundry Unit • WASHING

Modified specification for Mechanical Laundry Unit • WASHING
Modified specification for Mechanical Laundry Unit
• WASHING MACHINE — Capacity 50Kg:Electrically operated, Type: Side Loading,
Capacity: 50Kg dry weight filling per charge.
Inner Drum: Made of good quality stainless steel.
A motor drives the inner basket through set of multiple pulleys and ‘V’ belts.
The machine shall be provided with an integrally mounted electrical control panel.
Overall Dimension: 2100mm length x 1225mm width x 1700mm Height.
Inner Basket Dimension: 914mm Dia x 1220mm length.
Inner Drum Volume: 800 Litres. ; Water Consumption: 1200 Litres/hr.
The electrical connection will be suitable for operation on 415v, 3Phase, 50c/s, A.C.
Supply.
Electrical Connected Load: 3.7KW (Wash Motor: 5 HP)
Note: The machine will be fitted with suitable electrical heater of 18KW x 2 banks load, to
produce hot water for washing, if needed
Machine Safety Features:The outside basket door is interlocked electrically to ensure that the electrical drive system
do not function until the door is firmly closed.
An overflow arrangement prevents the machine from flooding with water.
Digital temperature controllers cuts of heaters at the preset temperature automatically, thus
ensuring the correct/economical use of heat energy.
• HYDRO EXTRACTOR — Capacity 25Kg :Electrically operated, Type: 3 point suspension ; Capacity: 25 Kg dry weight filling charge.
Drum: Inner and outer drum made of good quality stainless steel.
The inner basket designed for free rotation. All contact parts with wash load made of
stainless steel. Outside basket is suspended on tough springs of machine frame so as to
avoid any vibration due to uneven load on high speed.
The electrical connection will be suitable for operation on 415v, 3Phase, 50c/s, A.C.
Supply. Pre programmed auto control panel for various speed control: will be provided.
Outer Dimension: 1200mm width x 1450mm depth x 1025mm height.; Volume: 112 Litres.
Inner basket Dimension: 660mm dia x 330mm depth.; Extractor Motor: 5 HP (3.7 KW)
Machine Safety Features:The outside basket door is electrically interlocked ensuring that the machine cannot start
until the door is in close position.
The large size drain designed for fast draining of water and avoids flooding of machine The
entire machine suspended to minimize vibration.
The set of angular contact ball bearing ensures free rotation of inner basket and designed to
accept varying axial and thrust loads at high speed.
• FLAT BED PRESSElectrically heated Flat Bed Press, Pneumatic and auto head opening Size of buck 1500mm
x 750mm (60”x30”).
Electric Connected load: 10.8 1KW.
Air Consumption: 3 CFM ; Air Pressure: 6 Kg/cm2
Over all dimension: 1700mm length x 1550mm width x 1265mm height The Frame is fitted
with head, buck and levers.
The buck is padded with one layer of asbestos clothes, one layer of cotton knitted padding!
two layers of blanket and covered with cotton cloth
Operation: The closure of the machine can be done by pressing of the two hand levers are
provided in the front. The releasing of any of the levers will make the head to open thus
ensuring the safety of the operator.
Pressure Adjustihg Device: The amount of pressure exerted between the head and the buck
at the locking of the head can be easily and quickly changed to suit the requirements of
different kinds of fabrics or garments of varying thickness.
Self Aligning System: The head is supported on the rocker arm by means of spring and
studs joint which ensures to give even pressing to uneven thickness of garments.
• ELECTRIC HAND IRON WITH TABLE.
• Heavy Duty electric hand Iron with Wooden top Table on structural steel frame
work.
• The electric Hand iron is manufactured out of gun metal and cast iron.
• The Overall Dimensions of 1525mm x 760mm x 915mm;
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• SORTING TROLLEY— (Stainless Steel)
To carry the dry linen, Complete stainless steel construction for long rust free life.
Trolley sides have pressed ribs for extra strength.
Corners would be rounded for easy movement and fitted with rubber bumpers to avoid
any damage.
These trolleys would be mounted with 4 Nos. swiveling type rubber wheels on ball
bearings.
The trolley is designed for light weight, rugged and easy manoeuver.
Four castors are provided in the frame.
Wheels: 4” dia
Internal Size: 550mm Lx 950mm W x 670mm H
• WET LINEN TROLLEY— (Stainless Steel)
To transport / carry the wet linen, Complete stainless steel construction for long rust
free life.
Trolley sides have pressed ribs for extra strength.
Corners would be rounded for easy movement and fitted with rubber bumpers to avoid
any damage.
These trolleys would be mounted with 4 Nos. swiveling type rubber wheels on ball
bearings.
These trolleys have a perforated S.S. mesh at the bottom are fitted with a drain valve.
The front two castors are fixed type and the rear two are of swivelling type.
Wheels: 4” dia;
Internal Size: 550mm Lx 725mm W x 550mm H
• AIR COMPRESSOR: Suitable capacity.
• Horizontal Rectangular High Pressure High vacuum Sterilizer, electrically
operated
Chamber Size
600mm width x 600mm height x 1200mm length, (2ft x 2ft x 4ft)
Chamber capacity
432 litres approximately
Door
Auto Feed Water pump
Inbuilt Vacuum Pump
SINGLE DOOR, Hinge type with radial locking
To draw the water, automatically, when needed in the inbuilt boiler
A suitable water ring vacuum pump to withstand negative pressure
and create high vacuum of 26”Hg for efficient drying and
sterilization of loads. It will be fitted with the required SS
condenser, pipings and fittings to enable efficient drying with the
use of the vacuum pump
Chamber: Stainless steel 316 quality
Door: Stainless steel 316 quality
Radial locking arm for Door: Stainless steel 304 quality
Outer cover: Stainless steel 304 quality
Inbuilt boiler I Steam generator: Stainless steel 304 quality
Connecting pipes: Stainless steel 304 quality
Jacket: Boiler quality steel plate
Stand: Mild steel with anticorrosion paint
Door Gasket: Silicon rubber gasket, withstand upto 140°C
Flush Mounting Panel: Made of Stainless steel 304 quality
PLC: Siemens make; Dot matrix Printer: Epson make
121°C to 134°C & 1.2 to 2.1kg/cm2
Material of Construction
Working Temperature &
Pressure
Electrical Heater Load
18 K W + Vacuum pump load
Power Supply
3 phase, 440V, AC 50Hz supply
Cycle operation mode
Automatic operated through Microprocessor (PLC), instead of
manual operating valve:
•
PLC based microprocessor with the facility of HMI which is
incorporated with the sterilizer.
•
Touch Screen HMI will be provided, GERMAN Technology,
Siemens make
•
The technician can program the cycles with his choice of
different settings of time, temperature and corresponding
pressure, which can be used to sterilize various types of
contents / materials. HMI controlled having six different
settings of the cycle. Five cycles can be pre-set as per the
customer’s requirement and One cycle can be left un
programmed for the flexibility of the customer so that they
can set and select his choice of programming.
•
Digital displays of Chamber Pressure, temperature, Cycle no.,
Batch no., Time & Date, Alarm indicator, Error code, Low
water indicator
•
Features of HMI — Provision of ‘error code analysis’ inbuilt,
Password protection for security,
•
Test: Leak Test, Inbuilt Bowie & dick process test, High
pressure high vacuum-vacuum holding test and Standard
Process test
•
Printer (EPSON make dot matrix): Pinter that will
automatically and continuously monitor and record dates,
time of day, load, identification no. and operating parameter.
Safety features
Door locking facility, Low water protection system, Pressure cut
off facility and all other necessary safety features etc.
Alarms
Other Fittings
Standards
Documentation
If chamber leak test failed, If temperature chamber overshoots, If
chamber temperature rises above the set value, Vacuum pump trip,
Sterilization timer stop in case of temperature drop and Sterilization
timer reset in case of temperature drop.
The sterilizer will be fitted with pressure gauge, compound gauge,
plug screen, vacuum breaker, steam trap, safety valve and water
reading glass and valves etc.
IS: 3829 part 1 and CE
User manual in English, Warranty certificate and Hydraulic test
certificate, 10., 00., DQ, P0., Gauge calibration certificate, material
test certificate
Special Condition:
1.
Warranty must be 1 year.
2.
Manufacturing experience of company minimum 3 years.
3.
Laundry equipment manufacturing company should have valid ISO certificate &
CE certified.
4.
Should also quote for CMC for 5 years.
5.
Installation on turnkey basis.
6.
A firm assurance of manufacturer to be given regarding the supply of spare!
accessories for 5 years after the warranty period.
Chapati Making M/c along with following machines and
specification:-
1.
Spiral Dough kneading machine should be
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
2.
Bowl volume
Rated Voltage
Rated Frequency
Power
Rated Power Unit
Max. Kneading capacity
Mixing Speed
Bowl Speed
IPNO
Net Weight
Dimensions
-
50 L
220V
50Hz
2.2KW
2.9KW
- 20kg
185r/min
16r/min
IP×1
130 kg
920 × 530 × 935 (mm)
Dough Shatter Table should be
a.
b.
c.
d.
e.
f.
g.
h.
Roller Length
Rated voltage
Rated Frequency
Power
Rated Power input
IPNO
Net Weight
Dimension
-
530mm
220V – 280V
50Hz
6.55 KW
6.85 KW
IP × 1
280 kg
2450×875×1230 (mm)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising