LED Par 64 10mm Version 2

LED Par 64 10mm Version 2
www.ColorKeyLED.com
LED Par 64
10mm Version 2
LED Par 64 10mm V2 Manual
Mode Selection
The LED Par 64 10mm V2 has 8 modes or functions that can be set using the Mode select
button on the back of the unit. The values for each Mode are set using the Up and Down
select buttons located next to the Mode select button. The LED screen above the select
buttons will display the Mode or function the unit is set to along with the value set for that
function when applicable.
Mode
Screen
Function
DMX Modes
DMX (3 Channel)
001.
DMX (6 Channel)
001
DMX Control
3 Channel DMX 001-512
DMX Control
6 Channel DMX 001-512
Stand Alone Modes
Static Colors
CL0
Color Jump
J.01
Color Fade
F.01
Auto Mode
A.00
Sound Active Mode
S.01
Static Color
Select 1-7
Color Jump
Speed Select 01-99
Color Fade
Speed Select 01-99
Runs through Color Jump
and Color Fade Modes
Sound Sensitivity
Select 01-31
Master / Slave Mode
Master / Slave
www.ColorKeyLED.com
SLA.
Sets unit to Slave Mode
Copyright 2008
2
LED Par 64 10mm V2 Manual
DMX Mapping – 6 Channel
Channel
Value
1
0-255
2
0-255
Green
0%  100%
3
0-255
Blue
0%  100%
4
0-7
8-255
No function
Color macro mixing (Will override CH1-CH3)
0-16
No function
5
6
17-255
Function
Red
0%  100%
Strobe when using CH1-CH4
Speed/Sound Sensitivity when using CH6
0-31
No function
32-95
Color fading (Will override CH1-CH4)
96-159
RGB color jump (Will override CH1-CH4)
160-223
7 color jump (Will override CH1-CH4)
224-255
Sound activation (Will override CH1-CH4)
Instructions for using channels 5 and 6 with Color Fading and Color Macros
Channel 5 has 2 basic functions depending on how the other channels are set.
1. Strobe Speed: When channels 1-3 are set to a value between 1-255 channel 5 will control strobing
speed. This is also the case with channel 4 when it is set to a value between 8-255. However, any
value between 8-255 set for channel 4 will override any value set for channels 1-3. (For example, if
channel 2 is set to a value of 55 and channel 4 is set to a value of 100, the unit will use the channel
4 setting of 100 and ignore the channel 2 setting of 55.)
2. Color Fading/Jump Speed and Sound: When channel 6 is set to a value between 32-223 channel 5
will function as a speed control for Color Fading or Color Jumping. When channel 6 is set to a value
of 224-255 channel 5 will function as the Sound Sensitivity setting. Any value set for channel 6
between 32-255 will override any value settings for channels 1-4. (For example, if channel 4 is set
to a value of 40 and channel 6 is set to a value of 150, the unit will use the channel 6 setting of 150
for RGB Color Jumping and ignore the channel 4 setting of 40.)
DMX Mapping – 3 Channel
Channel
Value
1
0-255
Red
2
0-255
Green
0%  100%
3
0-255
Blue
0%  100%
www.ColorKeyLED.com
Function
0%  100%
Copyright 2008
3
LED Par 64 10mm V2 Manual
Stand Alone Modes
Static Color Mode
Press MODE Select button until screen reads CL0
Press UP or DOWN button to select one of the 7 desired colors:
CL1 Red, CL2 Green, CL3 Blue, CL4 Purple, CL5 Yellow, CL6 Cyan, CL7 White
Color Jump Mode
Press MODE Select button until screen reads J.01
Press UP or DOWN to select the speed from 01-99 (Slow to Fast).
Color Fading Mode
Press MODE Select button until screen reads F.01
Press UP or DOWN to select the fade speed from 01-99 steps (Slow to Fast).
Auto Running Mode
Press MODE Select button until screen reads A.00
The speed can be set via the speed settings of the Color Changing Mode & Color Fading Mode.
Sound Active Mode
Press MODE Select button until screen reads S.01
Press UP or DOWN to adjust the sound sensitivity levels from 01-31 (Low to High).
Master / Slave Modes
Setting up Master and Slave Units
Set the Master unit to either 3 channel or 6 channel DMX mode. Link the units using 3 pin DMX
cable by connecting the DMX out on the master unit to the DMX in on the 1st Slave unit.
Continue connecting more Slave units in like fashion by connecting the DMX out on the 1st
Slave unit to the DMX in on the 2nd Slave unit and so on to all of the Slave units in the chain (25
units max on a 20 amp circuit). On each of the Slave units press the MODE Select button until
the display shows SLA for slave mode. Now the slave units will follow the function of the
Master unit. (For example, if the Master unit is set to strobe in the purple color macro then all of
the slave units will also strobe in the purple color macro.)
www.ColorKeyLED.com
Copyright 2008
4
LED Par 64 10mm V2 Manual
Specifications
Specifications
# LED's
183 10mm LED’s (60 Red, 60 Green, 63 Blue)
Beam Angle
30°
Colors
16.7 Million
Foot Candles
18.5
Lux
199
LED Life Hours
100,000 Hours
Signal Protocol
DMX-512
DMX Channels
3 or 6
Programming Modes
Auto mode, DMX mode, Master / Slave mode, Sound Activation mode
Sound Activated
Yes
Built in Programs
Strobing and Color Fading with Fading Speed Variations
DMX Address Interface
LED Screen
Power Consumption
28 Watts
Power
AC110V 60Hz
Amps
Can run 25 units on a 20 Amp Circuit
Weight
8 lbs
Dimensions of Unit
17 x 12 x 10
Housing
Black or Silver
www.ColorKeyLED.com
Copyright 2008
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising