IP-PT-885 Speed Dome Web3.0 Operation Manual

IP-PT-885 Speed Dome Web3.0 Operation Manual
IP-PT-885
Speed Dome Web3.0 Operation Manual
Version 4.1.0
Table of Contents
1
2
Network Connection ................................................................................................................... 1
1.1
Preparation..................................................................................................................... 1
1.2
Log in .............................................................................................................................. 1
1.3
Live Interface ................................................................................................................. 3
1.4
Encode Setup ................................................................................................................ 3
1.5
Video Window Setup .................................................................................................... 4
1.6
System Menu ................................................................................................................. 5
1.7
Video Window Function Option .................................................................................. 5
1.8
PTZ Control.................................................................................................................... 6
1.9
PTZ Setup/Menu ........................................................................................................... 7
Setup ............................................................................................................................................. 9
2.1
Camera ........................................................................................................................... 9
2.1.1 Conditions ............................................................................................................... 9
2.1.2 Video ...................................................................................................................... 19
2.1.3 Audio ...................................................................................................................... 24
2.2
Network......................................................................................................................... 25
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
2.2.7
2.2.8
TCP/IP ................................................................................................................... 25
Connection ............................................................................................................ 27
PPPoE ................................................................................................................... 28
DDNS ..................................................................................................................... 29
IP filter .................................................................................................................... 30
SMTP (e-mail) ................................................................................................. 30
UPnP ...................................................................................................................... 32
SNMP..................................................................................................................... 33
i
2.2.9 Bonjour .................................................................................................................. 34
2.2.10
Multicast ......................................................................................................... 35
2.2.11
IEEE802 ......................................................................................................... 36
2.2.12
Qos .................................................................................................................. 36
2.3
PTZ................................................................................................................................37
2.3.1 Protocol.................................................................................................................. 37
2.3.2 Function ................................................................................................................. 38
2.4
Event ............................................................................................................................. 47
2.4.1 Video detect .......................................................................................................... 47
2.4.2 Alarm ...................................................................................................................... 50
2.4.3 Abnormality ........................................................................................................... 53
2.5
Storage ......................................................................................................................... 55
2.5.1 Record schedule and snapshot schedule ........................................................ 55
2.5.2 Destination ............................................................................................................ 55
2.5.3 Record control ...................................................................................................... 57
2.6
System .......................................................................................................................... 58
2.6.1
2.6.2
2.6.3
2.6.4
2.6.5
2.6.6
2.7
General .................................................................................................................. 58
Account .................................................................................................................. 59
Default.................................................................................................................... 63
Import/Export ........................................................................................................ 63
Auto maintenance ................................................................................................ 64
Firmware update .................................................................................................. 64
Information ................................................................................................................... 65
2.7.1 Version................................................................................................................... 65
2.7.2 Log.......................................................................................................................... 65
2.7.3 Online User ........................................................................................................... 66
3
Alarm ........................................................................................................................................... 68
4
Log out ........................................................................................................................................ 69
Important
The following functions are for reference only. Some series products may not
support all the functions listed below
ii
Usually we recommend IE 7 or higher version. For those versions below IE 7, it
may not support the operation of some functions.
iii
1 Network Connection
1.1 Preparation
This series speed dome product supports the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and
etc.
Please follow the steps listed below for network connection.
z Make sure the speed dome has connected to the network properly.
z Speed dome IP address and PC IP address shall be in the same network segment. If there is router,
please set the corresponding gateway and subnet mask.
z Use order ping ***.***.***.***(* speed dome address) to check connection is OK or not.
1.2 Log in
Open IE and input speed dome address in the address bar.
For example, if your device IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 1-1.
Input your IP
address here
Figure 1-1
The login interface is shown as below. See Figure 1-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
1
Figure 1-2
If it is your first time to login in, system pops up warning information to ask you whether install control
webrec.cab or not. Please click OK button, system can automatically install the control. When system is
upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the
control download. Or you can lower the IE security level. See Figure 1-3.
Figure 1-3
2
1.3 Live Interface
After you logged in, you can see the live monitor window. Now you can operate the speed dome via the
WEB. See Figure 1-4.
Figure 1-4
There are six sections:
z Section 1: Encode setup bar
z Section 2: Window adjust bar
z Section 3: System menu bar
z Section 4: Window function option bar
z Section 5: PTZ control
z Section 6: PTZ function
1.4 Encode Setup
The encode setup interface is shown as in Figure 1-5.
Figure 1-5
3
Please refer to the following sheet for detailed information.
Parameter
Function
Main stream
In normal network width environment, main stream can record
audio/video file and realize network monitor.
If network width is not sufficient, you can use sub stream to
realize network monitor. It is to reduce network bandwidth
usage.
You can select video monitor protocol from the dropdown list.
There are three options: TCP/UDP/Multicast.
Sub (Extra)
stream
Protocol
1.5 Video Window Setup
The interface is shown as in Figure 1-6.
1
2
3
4
5
Figure 1-6
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1
Image
control
Click it to open picture setup interface. See Figure 1-7. This
interface is on the top right pane.
2
Original
size
Click this button to go to original size. It is to display the actual
size of the video. It depends on the resolution of the video.
3
Full screen
Click it to go to full-screen mode. Double click the mouse or
click the Esc button to exit the full screen.
4
Width and
height ratio
Click it to restore original ratio or suitable window.
5
Open/close
PTZ
interface
Left click it to display or hide the PTZ control interface.
The picture setup interface is shown as in Figure 1-7.
4
Figure 1-7
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
Brightness setup icon. It is to adjust
monitor video brightness.
Contrast setup icon. It is to adjust
monitor video contrast ness.
Saturation setup icon. It is to adjust
monitor video saturation.
Hue setup icon. It is to adjust
monitor video hue.
Reset
Note:
z All the operations here
apply to WEB end
only.
z Please go to Setup>Camera->Conditions
to adjust brightness,
contrast, hue and
saturation setup.
Restore brightness, contrastness
saturation and hue to system default
setup.
1.6 System Menu
System menu is shown as in Figure 1-8.
Please refer to chapter 1.3 Live, chapter 2 Setup, chapter 3 Alarm, chapter 5 Log out for detailed
information.
Figure 1-8
1.7 Video Window Function Option
The interface is shown as below. See Figure 1-9.
5
Figure 1-9
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1/2
Alarm
output
3
Digital
zoom
4
Snapshot
Click it to generate an alarm output.
There are two alarm output icons since this series product
supports two relay output.
Please note the alarm output interface may vary due to
different series products.
When video is in original status, click this button you can
select any zone to zoom in. After zoom in ,you can drag the
zoom in area in the specified area. Right click mouse system
restores original status. You can use the wheel to zoom out
the video.
You can snapshoot important video.
You can go to Setup->Camera->Video->Path to modify the
local record save path.
5
Triple snap
6
Record
Click it, system can snap at 1f/s for three times. All images
are memorized in system storage folder.
When you click local record button, the system begins
recording.
You can go to Setup->Camera->Video->Path to modify the
local record save path.
7
Audio
output
Turn on or off audio when you are monitoring.
You can go to Setup->Camera->Audio to set.
8
Bidirectional
talk
Click it to begin audio talk. You can go to Setup->Camera>Audio to set bidirectional talk mode.
9
Help
Click it to open help file.
1.8 PTZ Control
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please go to Setup>System->PTZ to set.).
6
Here you can view direction keys, speed, zoom, focus, iris button. See Figure 1-10.
z PTZ direction: PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom
left/bottom right/ fast positioning.
z Speed: The step 8 speed is faster than step 1.
Figure 1-10
1.9 PTZ Setup/Menu
The PTZ setup/Menu interface is shown as in Figure 1-11.
Figure 1-11
Click PTZ set button, the interface is shown as in Figure 1-12.Here you can select scan, preset, tour
pattern, assistant function and etc.
7
Figure 1-12
Please refer to the following sheet for PTZ setup information.
Parameter
Function
Scan
z
Select Scan from the dropdown list, click Start button, you can
begin scan operation. Default SN is 1.
Preset
z
Tour
z
Pattern
z
Input the preset value and then click View button, the camera
turns to the corresponding position of the preset.
Select Tour from the dropdown list and then click Start button,
you can begin tour.
You can select Pattern from the dropdown list and then click
Start button to begin PTZ movement.
Assistant
z
Reserved assistant function.
It is the accurate positioning function. Please input
corresponding horizontal angle, tilt angle, and speed dome
zoom speed and then click Goto button to go to a specified
position.
z One unit of the horizontal angle or tile angle stands for 0.1
degree.
For detailed setup information, please go to Setup->PTZ-Function.
Goto
z
8
2 Setup
2.1 Camera
2.1.1 Conditions
Here you can set camera property. Adjust video parameter to get best preview effect. See Figure 2-1.
Figure 2-1
Please refer to the following sheet for detailed information.
Parameter
Function
Config File
Here you can set camera setup mode. It includes:
normal/day/night.
White Balance
It is to set camera white balance. It includes:
auto/manual/ATW/outdoor/indoor/outdoor auto/sodium light
auto/sodium light.
Exposure
It is to set camera exposure mode. It includes:
auto/manual/aperture has the priority/shutter has the priority.
NR
It is to set camera denoise mode. It includes: 2D NR/3D NR.
Day/Night
It is to set camera day/nigh switch mode. It includes:
auto/B&W/Color.
Focus
It is to set camera focus mode. It includes: auto/manual/semi
auto.
Zoom
It is to set camera digital zoom and zoom rate.
9
Sharpness
It is to set camera lens sharpness, and sharpness control level.
Picture
Restart
It is to set camera video. It includes: hue/brightness/saturation/
chroma control/gamma/picture flip/picture freeze.
It is to reboot camera.
Default
It is to restore factory default setup.
Important
Please make sure your purchased camera supports all the functions listed here.
2.1.1.1 White Balance
White balance interface is shown as below. See Figure 2-2.
Figure 2-2
Please refer to the following sheet for detailed information.
Parameter
Function
WB mode
z
z
It is to set camera white balance. It includes:
auto/manual/ATW/outdoor/indoor/outdoor auto/sodium
light auto/sodium light.
For manual mode, you can input red gain and blue gain
value.
2.1.1.2 Exposure
Exposure interface is shown as below. See Figure 2-3.
10
Figure 2-3
Please refer to the following sheet for detailed information.
Parameter
Function
Exposure mode
z
z
z
z
z
It is to set camera exposure mode. It includes:
auto/manual/aperture has the priority/shutter has the
priority. The default setup is auto.
For the auto exposure mode, the gain, shutter and iris are
in auto mode.
For manual exposure mode, the gain, shutter and aperture
is in manual mode.
When the aperture has the higher priority, the aperture is
in the manual mode and the gain and shutter is in auto
mode.
When the shutter has the priority, the shutter is in manual
mode, gain and aperture is in auto mode.
Exposure
compensation
It can adjust video whole brightness via setting exposure object
brightness so that it can suit for different environments.
Gain level
Shutter
It is to set video brightness under the low illumination
environments.
It is to set camera exposure time.
Iris
It is to set camera iris.
Slow exposure
If the light may change greatly, you can use slow exposure to
get image so that the camera can get stable video.
It is to set camera max gain.
Max Auto gain
11
Slow shutter
Auto Slow
Shutter Min
value
BLC
WDR Mode
AE resume
HLC
In lower illumination environment, you can lower the cameras
auto exposure time to capture the image and enhance the
definition. For the moving object , the trail may appear. Please
note it is valid in auto mode.
It is to set camera min shutter value.
For the environments of strong contrast effect, such as under
the backlight environment, system can auto adjust image
contrast to get clear object.
For the environments of strong contrast effect, it can auto
adjust image contrast so that you can see the dark and bright
section at the same time.
Manually adjust Iris + or Iris -, system can auto resume
previous exposure mode.
When there is strong light source in the environment, system
can auto adjust video brightness to remove the over exposure
effect.
2.1.1.3 NR (Noise Reduction)
The noise reduction interface is shown as in Figure 2-4.
Figure 2-4
Please refer to the following sheet for detailed information.
12
Parameter
Function
2D NR
It is to control noise. The higher the level is; the small the noise
is. Comparing with the previous one, the picture may become a
little bit blurry.
It is to control noise. The higher the level is, the small the noise
is. Comparing with the previous image, the moving object may
have trail.
3D NR
2.1.1.4 Day/Night
The day/night mode is shown as in Figure 2-5.
Figure 2-5
Please refer to the following sheet for detailed information.
Parameter
Function
Day/night
It is to set camera day/night mode. It includes: B&W/color/auto.
Sensitivity
It is to camera day/night switch sensitivity.
2.1.1.5 Focus
The focus interface is shown as in Figure 2-6.
13
Figure 2-6
Please refer to the following sheet for detailed information.
Parameter
Function
Focus mode
It is to set camera focus mode. It includes: auto/manual/semi
auto.
It is to camera focus distance in case the focus distance is too
small and the focus goes to the enclosure. At the same time,
you can change focus distance to adjust focus speed.
It is to set camera focus sensitivity. The higher the value is, the
easier it is to activate focus. The lower the value is, the difficult
it is to activate focus.
It is to set IR light focus correction function to enhance focus
effect and remove the IR light effect on the focus.
Focus limit
Focus sensitivity
IR Correction
2.1.1.6 Zoom
Zoom interface is shown as in Figure 2-7.
14
Figure 2-7
Please refer to the following sheet for detailed information.
Parameter
Function
Digital zoom
It is to enable/disable digital zoom.
Zoom speed
It is to set camera zoom speed. The bigger the value is, the
faster the speed is.
2.1.1.7 Sharpness
Sharpness interface is shown as in Figure 2-8.
Figure 2-8
15
Please refer to the following sheet for detailed information.
Parameter
Function
Sharpness
It is to set camera sharpness. The higher the sharpness is, the
clear the image is. The object edge becomes clear too.
It is to set camera control level. The higher the value is, the
strong the control level is.
Sharpness
control level
2.1.1.8 Picture
Picture interface is shown as in Figure 2-9.
Figure 2-9
Please refer to the following sheet for detailed information.
Parameter
Function
Hue
It is to set picture hue.
Saturation
It is to set color purity. The higher the purity is, the more color
the video is. The lower the purity is, the dark the video is.
It is to set video color control level. The higher the value is, the
higher the control level is .
It is to set image gamma value.
Chroma control
Gamma
Brightness
Picture Flip
It is to set video brightness. The higher is value is, the bright
the video is.
It is to set video display mode. It is to turn camera.
16
Picture Freeze
System goes to preset video when you are calling a preset.
System does not show the video during the PTZ movement.
System just directly goes to the preset.
2.1.1.9 Restart
Restart interface is shown as in Figure 2-10.
Figure 2-10
Please refer to the following sheet for detailed information.
Parameter
Function
Restart
It is to reboot camera.
2.1.1.10 Default
Default interface is shown as in Figure 2-11.
17
Figure 2-11
Please refer to the following sheet for detailed information.
Parameter
Function
Default
It is to restore camera parameter to factory default setup.
2.1.1.11 Profile Management
Profile management interface is shown as in Figure 2-12.
Figure 2-12
Please refer to the following sheet for detailed information.
18
Parameter
Function
Profile
Management
There are three modes: normal/full-time/schedule. The default
setup is normal.
Normal
It is to adopt the general parameter on the profile file.
Full-time
It is to adopt day or night general parameter on the profile file
all the time.
It is to adopt the day or night parameter on the profile file by
time you set here.
Schedule
2.1.2 Video
2.1.2.1 Video bit stream
The video bit stream interface is shown as below. See Figure 2-13.
Figure 2-13
Please refer to the following sheet for detailed information.
Parameter
Main
stream
Bit stream type
Function
It includes general stream, motion stream and alarm
stream. You can select different encode frame rates for
different recorded events.
The frame rates of the motion detect and alarm is
customized.
19
Parameter
Encode mode
Resolution
Function
There are four options: H.264, H.264B, H.264H, and
MJPEG encode mode.
z
H.264 : Main Profile encode mode.
z
H.264B :Baseline Profile encode mode.
z
z
H.264H: High Profile encode mode.
MJPEG: In this encode mode, the video needs
general large bit stream to guarantee the video
definition. You can use the max bit stream value in
the recommend bit to get the better video output
effect.
There are multiple resolutions. You can select from the
dropdown list.
For each resolution, the recommended bit stream value
is different.
Frame Rate
(FPS)
PAL: 1~25f/s,NTSC: 1~30f/s..
Bit Rate Type
There are two options: VBR and CBR.
Please note, you can set video quality in VBR mode.
In MJPEG mode, the bit stream control mode can only
be CBR.
The frame rate may vary due to different resolutions.
Recommended Recommended bit rate value according to the resolution
Bit
and frame rate you have set.
Bit Rate
I Frame
z
In CBR, the bit rate here is a fixed value.
z
It is the max value in VBR mode.
Here you can set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50.
Recommended value is frame rate *2.
Important
I frame interval setup is null if it is the MJPEG
encode mode.
Watermark
Sub
stream
Enable
Bit stream type
This function allows you to verify the video is tampered
or not.
The max length is 128-digit. The character can only
include number, character, underline and hyphen.
Please check the box here to enable extra stream
function.
This function is enabled by default.
General bit stream.
20
Parameter
Encode mode
Resolution
Function
There are four options: H.264, H.264B, H.264H, and
MJPEG encode mode.
z
H.264 : Main Profile encode mode.
z
H.264B :Baseline Profile encode mode. H.264B is
mainly for Blackberry cell phone to realize the
monitor. You need to enable the sub stream
function in your camera and set the resolution as
CIF. Then you can monitor via the Blackberry cell
phone.
z
H.264H: High Profile encode mode.
z
MJPEG: In this encode mode, the video needs
general large bit stream to guarantee the video
definition. You can use the max bit stream value in
the recommend bit to get the better video output
effect.
There are multiple resolutions. You can select from the
dropdown list.
For each resolution, the recommended bit stream value
is different.
Frame Rate
(FPS)
PAL: 1~25f/s,NTSC: 1~30f/s..
Bit Rate Type
There are two options: VBR and CBR.
Please note, you can set video quality in VBR mode.
The frame rate may vary due to different resolutions.
Recommended Recommended bit rate value according to the resolution
Bit
and frame rate you have set.
Bit Rate
I Frame
z
In CBR, the bit rate here is a max value. In dynamic
video, system needs to lower frame rate or video
quality to guarantee the value.
z
It is null in VBR mode.
z
Please refer to recommended bit rate for the detailed
information.
Here you can set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50.
Recommended value is frame rate *2.
Important
I frame interval setup is null if it is the MJPEG
encode mode.
2.1.2.2 Snapshot
21
The snapshot interface is shown as in Figure 2-14.
Figure 2-14
Please refer to the following sheet for detailed information.
Parameter
Function
Snapshot type
There are two modes: general (schedule) and Event
(activation).
General (schedule) snapshot is to snap in the specified period.
Event (Activation) snapshot Is to snap when the motion detect,
camera masking, local alarm event occurrence.
If you want to use this function, please make sure:
z The event occurred during the specified period.
z Motion detect, video masking, local alarm and
corresponding snap function are all enable.
Image size
It has relationship with the resolution of the main stream.
Quality
It is to set the image quality. There are six levels.
Interval
It is to set snapshot frequency. The value ranges from 1s to 7s.
2.1.2.3 Video Overlay
The video overlay interface is shown as in Figure 2-15.
Figure 2-15
22
Please refer to the following sheet for detailed information.
Parameter
Function
Privacy mask
z
Here you can privacy mask the specified video in the monitor
video.
z
Click Setup button, you can set privacy mask region. System
max supports 4 privacy mask zones.
z
You can enable this function so that system overlays time
information in video window.
z
There is no time title if you do not enable this function here.
z
Click Setup button, you can set time title display region. You
can use the mouse to drag the time tile position.
z
You can enable this function so that system overlays channel
information in video window.
z
There is no channel title if you do not enable this function
here.
z
Click Setup button, you can set channel title display region.
You can use the mouse to drag the channel tile position.
z
You can enable this function so that system overlays preset
information in video window.
There is no preset title if you do not enable this function here.
Time Title
Channel Title
Preset Title
z
Temperature
Refresh
z
Click Setup button, you can set preset title display region.
You can use the mouse to drag the preset tile position.
z
You can enable this function so that system overlays speed
dome inside temperature information in video window.
z
There is no temperature if you do not enable this function
here.
z
Click Setup button, you can set temperature title display
region. You can use the mouse to drag the temperature tile
position.
After you successfully set privacy mask zone, channel title, time
title, you can click Refresh button to video the effect.
2.1.2.4 Path
The storage path interface is shown as in Figure 2-16.
Here you can set snap image saved path (
(
in the preview interface) and the record storage path
in the preview interface).The snap picture default setup is C:\PictureDownload and record file
default setup is C:\RecordDownload.
23
Please click the Save button to save current setup.
Figure 2-16
2.1.3 Audio
The audio interface is shown as below. See Figure 2-17.
Important
Please make sure you have enabled the video function, otherwise you can not enable the audio
function.
Figure 2-17
Please refer to the following sheet for detailed information.
Parameter
Function
Audio enable
z
z
Main stream: Recorded file only contains video by default.
You need to check the audio box here to enable audio
function so that the main stream the network transmitted is
audio/video composite stream.
Sub (Extra) stream: Recorded file only contains video by
default. You need to check the audio box here to enable
audio function so that the extra stream the network
transmitted is audio/video composite stream.
24
Encode mode
The encode mode of the main stream and extra stream include
PCM, G.711A and G.711Mu.
The setup here is for audio encode mode and the bidirectional
talk encode both.
2.2 Network
2.2.1 TCP/IP
The TCP/IP interface is shown as in Figure 2-18.
Figure 2-18
Please refer to the following sheet for detailed information.
Parameter
Function
Host Name
It is to set current host device name.
Ethernet Card
Please select the Ethernet port if the device has several
network cards.
Mode
There are two modes: static mode and the DHCP mode.
Mac Address
z
The IP/subnet mask/gateway are null when you select the
DHCP mode to auto search the IP.
z
If you select the static mode, you need to set the IP/subnet
mask/gateway manually.
z
Besides, IP/subnet mask/gateway and DHCP are readonly when the PPPoE dial is OK.
It is to display host Mac address. It is read-only.
25
IP Version
It is to select IP version. IPV4 or IPV6.
You can access the IP address of these two versions.
z
z
Please note system needs to check the validity of all
IPv6 addresses. The IP address and the default gatew a
shall be in the same IP section. That is to say, the
specified length of the subnet prefix shall have the sa
string.
When PPPoE function is enabled, the IP/subnet
mask/default gateway is read-only. You can not set or
restore default setup.
IP Address
Please use the keyboard to input the corresponding number to
modify the IP address and then set the corresponding subnet
mask and the default gateway.
Default Gateway
It is the similar gateway of the IPv4. It shall not be left in blank.
Preferred DNS
DNS IP address. It is the similar DNS of the IPv4. It shall not be
left in blank.
Alternate DNS
Alternate DNS IP address. It is the similar DNS of the IPv4. It
shall not be left in blank.
Enable
ARP/Ping set
device IP
address service.
You can use ARP/Ping command to modify or set the device IP
address if you know the device MAC address.
Before the operation, please make sure the speed dome and
the PC in the same LAN. This function is on by default.
You can refer to the steps listed below.
Step 1: Get an IP address. Set the speed dome and the PC in
the same LAN.
Step 2: Get the physical address from the label of the speed
dome.
Step 3: Go to the Run interface and then input the following
commands.
arp –s <IP Address> <MAC>
ping –l 480 –t <IP Address>
Such as:arp ‐s 192.168.0.125 11‐40‐8c‐18‐10‐11
ping ‐l 480 ‐t 192.168.0.125
Step 4: Reboot the device.
Step 5: You can see the setup is OK if you can see there are
output information such as “Reply from 192.168.0.125 …” from
the command output lines. Now you can close the command
line.
Step 6: Open the browse and then input http://<IP addres>.
Click the Enter button, you can access now.
26
2.2.2 Connection
The connection interface is shown as in Figure 2-19.
Figure 2-19
Please refer to the following sheet for detailed information.
Parameter
Function
Max
connection
It is the max Web connection for the same device. The value ranges from 1
to 20. The default setup is 10.
TCP port
The value ranges from 1025 to 65535. The default value is 37777. You can
input the actual port number if necessary.
UDP port
The value ranges from 1025 to 65535. The default value is 37778. You can
input the actual port number if necessary.
HTTP port
The value ranges from 1025 to 65535. The default value is 80. You can
input the actual port number if necessary.
27
RTSP port
z
z
z
z
Usually, the default value is 554. You do not need to input again if you
are using the default value. When you are using QuickTime (Apple
browser) or VLC play real-time video, you can use the following format
to play. The Blackberry also supports this function.
Real-time monitor bit stream Url format. Please specify the channel
number, bit stream type in the Url if you are requesting real-time
monitor bit stream Rtsp stream media service. You still need to
provide user name or password if it has verification information.
When you are using Blackberry phone to access, the bit stream mode
shall be H.264B, resolution is CIF and the audio shall be disabled.
The Url format is shown as below:
rtsp://username:password@ip:port/cam/realmonitor?channel=1&subtype=0
You need to input the following items manually.
Username/password/IP/port/subtype.
The IP is device IP and the port default value is 554. You can leave it in
blank if it is the default value. The channel number begins with 1.
subtype:bit stream type,main stream is 0(subtype=0)and extra
stream is 1(subtype=1).
You do not need to input the user name and password if you do not need
the verification. Such as:
Main stream:rtsp://ip:port/cam/realmonitor?channel=1&subtype=0
HTTPS
Enable
It is to enable HTTPs communication service control. If you enable this
function, you can use https://ip:port to login the device. In data encryption
protection mode, you can use https://ip to login if you are using the default
port.
HTTPS
Port
The HTTPs communication port value ranges from 1025 to 65535.
Important
The value 0 to 1024 (excluding the default value of HTTP/RTSP/HTTPs), 1900, 3800, 5000, 5050, 9999,
37776, 37780-37880, 39999 and etc are the special ports value and they are not open for user to set.
2.2.3 PPPoE
The PPPoE interface is shown as in Figure 2-20.
Input the PPPoE user name and password you get from the IPS (internet service provider) and enable
PPPoE function. Please save current setup and then reboot the device to get the setup activated.
Device connects to the internet via PPPoE after reboot. You can get the IP address in the WAN from
the IP address column.
28
PPPoE is set to connect to the internet. You can get an account from your IPS (Internet service
provider), you can set here to dial to the interface. You can see the registered IP address in the
interface if your setup is right.
Please note, you need to go to the IP address item to view the device current device information.
You can access the client-end via this address.
Figure 2-20
2.2.4 DDNS
The DDNS interface is shown as in Figure 2-21.
The DDNS is to set to connect the various servers so that you can access the system via the server.
Please go to the corresponding service website to apply a domain name and then access the system
via the domain. It works even your IP address has changes.
Figure 2-21
29
Please refer to the following sheet for detailed information.
Parameter
Function
Server Type
You can select DDNS protocol from the dropdown list and then
enable DDNS function.
Server IP
DDNS server IP address
Server Port
DDNS server port.
Domain Name
Your self-defined domain name.
User
The user name you input to log in the server.
Password
The password you input to log in the server.
Update period
z
Device IP and service connection refresh period.
z
The default setup is 10 minutes.
2.2.5 IP filter
The IP filter interface is shown as in Figure 2-22.
You can enable IP filter function so that some specified IP user can access the speed dome.
You can add IP address or IP address section.
If you do not check the box here, it means there is on access limit.
Figure 2-22
2.2.6 SMTP (e-mail)
The SMTP interface is shown as in Figure 2-23.
30
Figure 2-23
Please refer to the following sheet for detailed information.
Parameter
Function
SMTP Server
Input server address and then enable this function.
Port
Default value is 25. You can modify it if necessary.
Anonymity
For the server supports the anonymity function. You can auto
login anonymously. You do not need to input the user name,
password and the sender information.
User Name
The user name of the sender email account.
Password
The password of sender email account.
Sender
Sender email address.
Authentication
(Encryption
mode)
You can select SSL or none.
Title (Subject)
Input email subject here.
Attachment
System can send out the email of the snapshot picture once
you check the box here.
Mail receiver
Input receiver email address here. Max three addresses.
31
Parameter
Function
Interval
The send interval ranges from 0 to 3600 seconds. 0 means
there is no interval.
Please note system will not send out the email immediately
when the alarm occurs. When the alarm, motion detection or
the abnormity event activates the email, system sends out the
email according to the interval you specified here. This
function is very useful when there are too many emails
activated by the abnormity events, which may result in heavy
load for the email server.
Please check the box here to enable this function.
Health mail
enable
Update period
(interval)
Email test
This function allows the system to send out the test email to
check the connection is OK or not.
Please check the box to enable this function and then set the
corresponding interval.
System can send out the email regularly as you set here.
The system will automatically sent out an email once to test
the connection is OK or not .Before the email test, please
save the email setup information.
2.2.7 UPnP
It allows you to establish the mapping relationship between the LAN and the public network.
Here you can also add, modify or remove UPnP item. See Figure 2-24.
In the Windows OS, From Start->Control Panel->Add or remove programs. Click the “Add/Remove
Windows Components” and then select the “Network Services” from the Windows Components Wizard.
Click the Details button and then check the “Internet Gateway Device Discovery and Control client” and
“UPnP User Interface”. Please click OK to begin installation.
Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the speed dome can auto
detect it via the “My Network Places”
32
Figure 2-24
2.2.8 SNMP
The SNMP interface is shown as in Figure 2-25.
The SNMP allows the communication between the network management work station software and the
proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or
establish the SNMP service before you use this function. You need to reboot the device to activate the
new setup.
Figure 2-25
Please refer to the following sheet for detailed information.
33
Parameter
Function
SNMP Port
The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to 65535.
The default value is 161
Read Community
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read all the objects the SNMP
supported in the specified name. The default setup is public.
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read/write/access all the objects the
SNMP supported in the specified name. The default setup is
write.
The destination address of the Trap information from the
proxy program of the device.
The destination port of the Trap information from the proxy
program of the device. It is for the gateway device and the
client-end PC in the LAN to exchange the information. It is a
non-protocol connection port. It has no effect on the network
applications. It is a UDP port not TCP port. The value ranges
from 1 to 165535. The default value is 162.
z Check SNMP v1, system only processes the information
of V1.
z Check SNMP v2, system only processes the information
of V2.
z Check SNMP v3, you can set account and password. You
need to set the corresponding account and password for
security verification when the server wants to access the
device. At the same time, the V1 and V2 option is null.
Write Community
Trap address
Trap port
SNMP version
2.2.9 Bonjour
The Bonjour interface is shown as below. See Figure 2-26.
Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically
broadcast its service information and listen to the service information from other device.
You can use the browse of the Bonjour service in the same LAN to search the speed dome device and
then access if you do not know the speed dome information such as IP address.
You can view the server name when the speed dome is detected by the Bonjour. Please note the safari
browse support this function. Click the “Display All Bookmarks: and open the Bonjour, system can auto
detect the speed dome of the Bonjour function in the LAN.
34
Figure 2-26
2.2.10 Multicast
The multicast interface is shown as in Figure 2-27.
Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data
packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host
can just send out one data to transit. This function also depends on the relationship of the group
member and group of the outer.
Here you can set multicast address and port. You also need to go to Live interface to set the protocol as
Multicast.
Figure 2-27
35
2.2.11 IEEE802
IEEE802.1X works standing for local and metropolitan area networks and port based network access
control protocol. It supports manual operation of the client to choose means of authenticating by which
to control it to access to the Local Area Networks or not. It supports the ability to authenticate, to
calculate fee, to ensure security and to maintain requirements. See Figure 2-28.
Figure 2-28
Please refer to the following sheet for detailed information.
Parameter
Function
Authentication
PEAP (protected EAP protocol).
Username
It needs the username to login, which is authenticated by the
server.
Password
Please input password here.
2.2.12 Qos
The QoS interface is shown as below. See Figure 2-29.
Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and
jam problem and etc. For the network service, the quality of service includes the transmission bandwidth,
delay, the packet loss and etc. We can guarantee the transmission bandwidth, lower the delay, and
reduce the loss of the data packet and anti-dither to enhance the quality.
We can set the DSCP (Differentiated Services Code Point) of the IP to distinguish the data packet so
that the router or the hub can provide different services for various data packets. It can select the
different queues according to the priority of the packets and select the bandwidth of the each queue. It
can also discard at the different ratio when the broad bandwidth is jam.
36
Figure 2-29
Please refer to the following sheet for detailed information.
Parameter
Function
Real-time
monitor
The data packet of the network video monitor.
Command
The non-monitor packet such as device setup and search.
2.3 PTZ
2.3.1 Protocol
2.3.1.1 Network PTZ Setup
Network PTZ setup interface is shown as in Figure 2-30.
Figure 2-30
Please refer to the following sheet for detailed information.
37
Parameter
Function
Protocol
You can select from the dropdown list such as PELCOP,
PELCOD.
2.3.1.2 Analog PTZ
The analog PTZ is shown as in Figure 2-31.
Figure 2-31
Please refer to the following sheet for detailed information.
Parameter
Function
Address
It is to set the corresponding speed dome address. The default
setup is 1.
Baud rate
It is to set the baud rate of the camera. The default setup is
9600.
Data bit
The default setup is 8.
Stop bit
The default setup is 1.
Parity
You can set protocol parity mode. The default setup is none.
2.3.2 Function
In this part, you can operate the PTZ of the camera and control PTZ movement.
Parameter
Function
Preset
Set camera preset.
Tour
Set camera tour. Max 8 tours.
Scan
Set camera scan.
Pattern
Set camera pattern.
Privacy
mask
Set camera privacy mask setup.
38
PTZ speed
Set PTZ movement speed.
Idle motion
Set camera idle operation.
Power up
Set camera operation when system boots up.
PTZ restart
Restart camera PTZ.
Default
Restore camera PTZ default setup.
2.3.2.1 Preset
Preset interface is shown as in Figure 2-32.
Figure 2-32
Please refer to the following sheet for detailed information.
Parameter
Function
Preset No.
Set preset No. It becomes valid after you set.
Preset title
Set preset name. You can input self-defined preset name here.
Delete
Delete corresponding preset.
Save
Save current preset setup.
39
Add
Click it to add a new preset.
Clear
Clear all presets setup.
2.3.2.2 Tour
Tour interface is shown as below. See Figure 2-33.
Figure 2-33
Please refer to the following sheet for detailed information.
Parameter
Function
Tour No.
System auto allocates.
Tour title
Set tour name. You can input self-defined tour name here.
Start
Begin tour.
Please note this function is null if you have not set a tour.
Add
Click it to add a new tour.
Preset
Click Add button, you can add a new tour. The default preset
value is 1.
Double click tour No, you can see a dropdown list for you to
select.
Please set presets before you use tour function.
Duration
(Interval)
It is to set the staying time of the tour.
40
Save
Click it to save current setup.
Refresh
Refresh current interface.
2.3.2.3 Scan
Scan interface is shown as below. See Figure 2-34.
Figure 2-34
Please refer to the following sheet for detailed information.
Parameter
Function
Scan No.
System auto allocates.
Speed
Set scan speed here.
You can not set speed when camera is running scan.
Start
Begin scan.
Please note this function is null if you have not set a scan.
Set
Click set button, you can set left limit and right limit.
Left limit
Set camera left limit.
Right limit
Set camera right limit.
2.3.2.4 Pattern
Pattern interface is shown as below. See Figure 2-35.
41
Figure 2-35
Please refer to the following sheet for detailed information.
Parameter
Function
Pattern No.
System auto allocates.
Start
Begin pattern.
Please note this function is null if you have not set a
pattern.
Set
Click it you can see start/stop record buttons.
Start record
Click it to begin recording pattern setup.
Stop record
Click it to stop recording pattern setup.
2.3.2.5 Privacy mask
Privacy mask interface is shown as below. See Figure 2-36.
42
Figure 2-36
Please refer to the following sheet for detailed information.
Parameter
Function
SN
Please select privacy mask number from the dropdown list.
Enable
Check the box here to enable privacy mask function.
Draw
Click Draw button, you can see edit column. You can
drag and release mouse to set privacy mask region and
size.
z You can draw the edit column or you can right click to
remove.
Before the operation, please make sure you have
enabled privacy mask function.
Clear
Click it to clear all privacy mask setup.
z
2.3.2.6 PTZ speed
PTZ speed interface is shown as below. See Figure 2-37.
43
Figure 2-37
Please refer to the following sheet for detailed information.
Parameter
Function
PTZ speed
Here you can set camera PTZ speed.
2.3.2.7 Idle Motion
Idle motion interface is shown as below. See Figure 2-38.
Figure 2-38
44
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Check the box here to enable idle motion function.
Idle Motion
Here you can set preset, scan, pattern, tour.
Please note you need to set the corresponding
function first if you want to use it.
Idle time
Set idle time.
2.3.2.8 Power up
Power up interface is shown as below. See Figure 2-39.
Figure 2-39
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Check the box here to enable power up function.
Power up
Here you can set preset, scan, pattern, tour and auto.
Please note you need to set the corresponding
function first if you want to use it.
2.3.2.9 PTZ Restart
PTZ restart interface is shown as below. See Figure 2-40.
45
Figure 2-40
Please refer to the following sheet for detailed information.
Parameter
Function
PTZ restart
It is to reboot PTZ.
2.3.2.10 Default
Default interface is shown as below. See Figure 2-41.
Figure 2-41
46
Please refer to the following sheet for detailed information.
Parameter
Function
Default
Restore PTZ factory default setup.
2.4 Event
2.4.1 Video detect
2.4.1.1 Motion Detect
The motion detect interface is shown as in Figure 2-42.
Figure 2-42
Figure 2-43
47
Figure 2-44
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable motion detection function.
Sensitivity
There are six levels. The sixth level has the highest sensitivity.
Region
Working
Period
Anti-dither
z
There are six levels. The sixth level has the highest sensitivity.
z
Region: If you select motion detection type, you can click this
button to set motion detection zone. The light blue zones are
the valid motion detect area. All area are the valid motion detect
zone by default. You can use mouse to set invalid area.
z
Do remember clicking OK button to save your motion detection
zone setup.
z
Motion detection function becomes activated in the specified
periods. See Figure 2-43.
z
There are six periods in one day. Please draw a circle to enable
corresponding period.
z
Select date. If you do not select, current setup applies to today
only. You can select all week column to apply to the whole
week.
z
Click OK button, system goes back to motion detection
interface; please click save button to exit.
System only memorizes one event during the anti-dither period.
The value ranges from 0s to 100s.
48
Parameter
Function
Relay out
Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
alarm occurs.
Please note the relay output number here is for reference
only. The alarm output number may vary due to different
series products.
Alarm Delay
System can delay the alarm output for specified time after motion
detect alarm ended. The value ranges from 10s to 300s.
Record
channel
System auto activates motion detection channel to record once
motion detect alarm occurs (working with motion detection
function). Please note you need to go to Storage-> Schedule to
set motion detect record period and go to Storage->Record
control to set current channel as auto record.
Record Delay
System can delay the record for specified time after motion detect
alarm ended. The value ranges from 10s to 300s.
Send Email
If you enabled this function, System can send out email to alert
you when alarm occurs and ends.
PTZ
z
Here you can set PTZ movement when alarm occurs. Such as
go to preset x when there is an alarm.
z
The event type includes: preset, tour and pattern and etc.
Snapshot
It is snapshot activation function.
2.4.1.2 Video Masking
The video masking interface is shown as in Figure 2-45.
Figure 2-45
49
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable video masking function.
Sensitivity
There are six levels. The sixth level has the highest sensitivity.
Working
Period
z
Video masking function becomes activated in the specified
periods.
z
There are six periods in one day. Please draw a circle to enable
corresponding period.
z
Select date. If you do not select, current setup applies to today
only. You can select all week column to apply to the whole
week.
z
Click OK button, system goes back to motion detection
interface; please click save button to exit.
Anti-dither
System only memorizes one event during the anti-dither period.
The value ranges from 0s to 100s.
Relay out
Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
video masking alarm occurs.
Please note the relay output number here is for reference
only. The alarm output number may vary due to different
series products.
Alarm Delay
System can delay the alarm output for specified time after video
masking alarm ended. The value ranges from 10s to 300s.
Record
channel
System auto activates motion detection channel to record once
video masking alarm occurs (working with motion detection
function). Please note you need to go to Storage-> Schedule to
set motion detect record period and go to Storage->Record
control to set current channel as auto record.
Record Delay
System can delay the record for specified time after video
masking alarm ended. The value ranges from 10s to 300s.
Email
If you enabled this function, System can send out email to alert
you when alarm occurs.
PTZ
z
Here you can set PTZ movement when alarm occurs. Such as
go to preset x when there is an alarm.
z
The event type includes: preset, tour and pattern and etc.
Snapshot
It is snapshot activation function.
2.4.2 Alarm
2.4.2.1 Alarm activation
50
The alarm activation interface is shown as in Figure 2-46.
Figure 2-46
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable this function.
Working
Period
z
This function becomes activated in the specified periods.
z
There are six periods in one day. Please draw a circle to enable
corresponding period.
Select date. If you do not select, current setup applies to today
only. You can select all week column to apply to the whole
week.
z
z
Anti-dither
Sensor type
Relay out
Alarm Delay
Click OK button, system goes back to motion detection
interface; please click save button to exit.
System only memorizes one event during the anti-dither period.
The value ranges from 0s to 100s.
There are two options: NO/NC. From NO to NC, system enables
alarm. From NC to NO, system disables alarm.
z
Enable alarm activation function. You need to select alarm
output port so that system can activate corresponding alarm
device when alarm occurs.
z
Please note the relay output number here is for reference
only. The alarm output number may vary due to different
series products.
System can delay the alarm output for specified time after alarm
ended. The value ranges from 10s to 300s.
51
Parameter
Function
Record
Channel
System auto activates motion detection channel to record once
alarm occurs (working with motion detection function). Please
note you need to go to Storage-> Schedule to set current channel
as general record.
Record Delay
System can delay the record for specified time after alarm ended.
The value ranges from 10s to 300s.
Send Email
If you enabled this function, System can send out email to alert
you when alarm occurs and ends.
PTZ
z
Here you can set PTZ movement when alarm occurs. Such as
go to preset x when there is an alarm.
z
The event type includes: preset, tour and pattern.
Snapshot
You need to input capture channel number so that system can
backup motion detection snapshot file.
2.4.2.2 Relay output
The relay output interface is shown as in Figure 2-47.
Figure 2-47
Please refer to the following sheet for detailed information.
Parameter
Function
Alarm output
There are two output channels. Please click the corresponding
button. If you want to enable the alarm activation output function,
please press the corresponding button and then trigger.
Please note the interface here is for reference only. The
alarm output number may vary due to different series
products.
Trigger
When the alarm output channel is open, the output port can
immediately output an alarm once it occurred.
Refresh
Refresh alarm output status.
52
2.4.3 Abnormality
It includes five statuses: No SD card, capacity warning, SD card error, and disconnection and IP conflict.
There are two interfaces for you reference. See Figure 2-48 through Figure 2-52.
Figure 2-48
Figure 2-49
Figure 2-50
53
Figure 2-51
Figure 2-52
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
z
The abnormal events include: no disk, no space, disk error, net error,
offline, IP conflict.
z
You need to draw a circle to enable this function.
Record
System auto activates channel to record once an alarm occurs (For
offline type only. See Figure 2-52. ).
You need to check the box to enable this function.
Record
Delay
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Relay Out
The corresponding alarm output channel when alarm occurs. You need
to check the box to enable this function.
Relay out
Delay
The alarm output can delay for the specified time after alarm stops. The
value ranges from 10s to 300s.
54
Parameter
Function
Send
email
If you enable this function, system can send out email to alarm the
specified user.
2.5 Storage
2.5.1 Record schedule and snapshot schedule
In these two interfaces, you can add or remove the schedule record/snapshot setup. See Figure 2-53.
There are three record modes: general (auto), motion detect and alarm. There are six periods in one
day. Please make sure you have enabled the corresponding record mode in the Setup->Storage>Conditions.
You can view the current time period setup from the color bar.
z Green color stands for the general record/snapshot.
z Yellow color stands for the motion detect record/snapshot.
z
Red color stands for the alarm record/snapshot.
Figure 2-53
2.5.2 Destination
The destination interface is shown as in Figure 2-54.
It is to set the storage mode of the speed dome record file or snapshot pictures. There are two options:
local storagel/FTP. You can only select one mode. System can save according to the event types. It is
corresponding to the three modes (general/motion/alarm) in the Schedule interface. Please check the
box to enable the save functions.
55
Figure 2-54
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
It includes: general, motion detect and alarm.
Local
It is to save in the SD card.
FTP
It is to save in the FTP server.
The local interface is shown as in Figure 2-55. Here you can view local SD card information. You can
also operate the read-only, write-only, hot swap and format operation.
Figure 2-55
The FTP interface is shown as in Figure 2-56. You need to check the box to enable the FTP function.
When network disconnect occurred or there is malfunction. Emergency storage can save the
record/snapshot picture to the local SD card.
56
Figure 2-56
2.5.3 Record control
The record control interface is shown as in Figure 2-57.
Figure 2-57
Please refer to the following sheet for detailed information.
Parameter
Function
Pack
Duration
Here you can select file size. Default setup is 60 minutes.
Pre-record
Please input pre-record value here.
For example, you can input 4 here so that system can read the
previous four seconds video before the alarm occurrence from the
buffer and record the 4 seconds video in the file.
Please note, if there is no record when alarm record or motion detect
record occurred, system can record the N seconds’ video before the
event occurrence in the file.
Disk Full
There are two options: stop recording or overwrite the previous files
when HDD is full.
z Stop: Current working HDD is overwriting or current HDD is full,
it will stop record.
z Overwrite: Current working HDD is full; it will overwrite the
previous file.
57
Record
Mode
There are three modes: Auto/manual/close.
Record Bit
Stream
You can select main stream or extra stream.
2.6 System
2.6.1 General
The general interface includes the general setup and the date/time setup.
2.6.1.1 General
The general interface is shown as in Figure 2-58.
Figure 2-58
Please refer to the following sheet for detailed information.
Parameter
Function
Device
Name
It is to set device name.
Video
Standard
This is to display video standard.
Language
You can select the language from the dropdown list.
Please note the device needs to reboot to get the modification
activated.
2.6.1.2 Date and time
The date and time interface is shown as in Figure 2-59
58
Figure 2-59
Please refer to the following sheet for detailed information.
Parameter
Function
Date format
Here you can select date format from the dropdown list.
Time
Format
There are two options: 24-H and 12-H.
Time zone
The time zone of the device.
System
time
It is to set system time. It becomes valid after you set.
Sync PC
You can click this button to save the system time as your PC current
time.
DST
Here you can set day night save time begin time and end time. You
can set according to the date format or according to the week
format.
NTP
You can check the box to enable NTP function.
NTP server
You can set the time server address.
Port
It is to set the time server port.
Update
period
It is to set the sync periods between the device and the time server.
The update function is null if the value is 0.
2.6.2 Account
Note:
59
z
z
z
For the character in the following user name or the user group name, system max supports 6-digits.
The space in the front or at the end of the string is null. The valid string includes: character, number,
and underline.
The max user amount is 20 and the max group amount is 8. You can add or delete user group.
The factory default setup includes two levels: user and admin. .User management adopts
group/user modes. The user name and the group name shall be unique. One user shall be included
in only one group.
2.6.2.1 User name
In this interface you can add/remove user and modify user name. See Figure 2-60.
Figure 2-60
Add user: It is to add a name to group and set the user rights. See Figure 2-61.
Here you can input the user name and password and then select one group for current user.
Please note the user rights shall not exceed the group right setup.
For convenient setup, please make sure the general user has the lower rights setup than the admin.
60
Figure 2-61
Modify user
It is to modify the user property, belonging group, password and rights. See Figure 2-62.
Modify password
It is to modify the user password. You need to input the old password and then input the new password
twice to confirm the new setup. Please click the OK button to save.
For the user of the account rights, he can modify the password of other users.
Figure 2-62
2.6.2.2 Group
The group management interface can add/remove group, modify group password and etc.
The interface is shown as in Figure 2-63.
61
Figure 2-63
Add group: It is to add group and set its corresponding rights. See Figure 2-64.
Please input the group name and then check the box to select the corresponding rights. It includes: live
playback, record control, backup, PTZ control, user management and etc.
Figure 2-64
Modify group
Click the modify group button, you can see an interface is shown as in Figure 2-65.
Here you can modify group information such as remarks and rights.
62
Figure 2-65
2.6.3 Default
The default setup interface is shown as in Figure 2-66.
Please note system can not restore some information such as network IP address.
Figure 2-66
2.6.4 Import/Export
The interface is shown as in Figure 2-67.
Figure 2-67
63
Please refer to the following sheet for detailed information.
Parameter
Function
Import
It is to import the local setup files to the system.
Export
It is to export the corresponding system setup to your local PC.
2.6.5 Auto maintenance
The auto maintenance interface is shown as in Figure 2-68.
Here you can select auto reboot and auto delete old files interval from the dropdown list.
If you want to use the auto delete old files function, you need to set the file period.
Figure 2-68
2.6.6 Firmware update
The firmware interface is shown as in Figure 2-69.
Please select the upgrade file and then click the update button to begin firmware update.
Important
Do not turn off the device power, disconnect the device, reboot or shutdown the device during
the update period.
Please reboot the device if you update the improper program, otherwise some function module
of the device may become null!
64
Figure 2-69
2.7 Information
2.7.1 Version
The version interface is shown as in Figure 2-70.
Here you can view system software version, WEB version, release date and etc. Please note the
following information is for reference only.
Figure 2-70
2.7.2 Log
Here you can view system log. See Figure 2-71.
65
Figure 2-71
Please refer to the following sheet for log parameter information.
Parameter
Function
Type
Start time
Log types include: system operation, configuration operation, data
operation, alarm event, record operation, and user management, log
clear.
Set the start time of the requested log.
End time
Set the end time of the requested log.
Search
You can select log type from the drop down list and then click search
button to view the list.
You can click the stop button to terminate current search operation.
You can select one item to view the detailed information.
Detailed
information
Clear
You can click this button to delete all displayed log files.
Backup
You can click this button to backup log files to current PC.
2.7.3 Online User
The online user interface is shown as in Figure 2-72.
Here you can view online user name, group name, IP address and login time.
66
Figure 2-72
67
3 Alarm
Click alarm function, you can see an interface is shown as in Figure 3-1.
Here you can set device alarm type and alarm sound setup. When the specified alarm occurred (you
have subscribed), system can record the corresponding alarm information on the right pane of the alarm
list.
Figure 3-1
Please refer to the following sheet for detailed information.
Type
Parameter
Function
Motion detect
Alarm
System alarms when motion detection alarm
type
occurs,
Disk full
System alarms when disk is full.
Operation
Alarm
audio
HDD
malfunction
Camera
masking
External alarm
Prompt
Audio
Path
System generates an alarm when HDD is
malfunction.
System alarms when camera is viciously masking.
Alarm input device sends out alarm.
System automatically pops up alarm dialogue box.
When alarm occurs, system auto generates alarm
audio. The audio supports customized setup.
Here you can specify alarm sound file.
68
4 Log out
Click log out button, system goes back to log in interface. See Figure 4-1.
You need to input user name and password to login again.
Figure 4-1
Note:
z This manual is for reference only. Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z
z
z
All trademarks and registered trademarks are the properties of their respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website for more information.
69
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising