Table of Contents

Table of Contents
Table of Contents
Technical Information-----------------------------------1
Warning Statement--------------------------------------2
Read Before Riding-------------------------------------3
List of Parts-----------------------------------------------4
Front Bar---------------------------------------------------6
Tool Kits In The Tool Bag------------------------------7
Assembling The Multi-Point---------------------------8
Charging The Batteries-------------------------------12
Charging The Batteries Outside Scooter---------13
Riding The Multi-Point--------------------------------15
Table of Contents
Technical Information
Multi-Point
Model No.
Folding The Multi-Point-------------------------------19
Maintenance---------------------------------------------21
Wiring Diagram-----------------------------------------22
Product size
Type of motor
RMB Multi-Point
45 L x 27 W x 44 H inch (115
x 68 W x 113 cm)
Permanent-magnet
brushless DC wheel motor
Trouble Shooting Guide------------------------------24
Warranty-------------------------------------------------26
Instructions for optional attachments-------------31
Motor power
500 w Wheel motor, 48 V
Battery type
sealed lead acid battery
Battery capacity
48 Volt, 12Ah
Charger
110V-240V, UL approved
Charging time
4-6 hours
Max. speed
Up to 16 MPH ( 26 km/h)
Single charge
Up to 31 MILES (50 km)
Max capacity
300 LBS (136 kg)
Net weight
101 LBS (46 kg)
1
Warning Statement
Multi-Point
Read Before Riding
Multi-Point
WARNING
THE RMB MULTI-POINT IS NOT A TOY AND SHOULD
NOT BE OPERATED BY ANYONE UNDER 12 YEARS OLD.
Safety Instructions:
(Please take note of the following before each ride)

The maximum weight capacity is 300 lbs.

Only one person at a time should ride.

Always wear protective gear including knee and elbow pads and
an approved safety helmet when riding the Multi-Point.

Before riding, be sure to check that all pivot points, locking
buttons, quick releases, and latches are secured properly.

The power switch lock must be in the “off” position when the
Multi-Point is being charged.

Do not use the Multi-Point when it is raining.

Do not place the battery near heat or fire.

Do not expose the charger to water or any moisture.

Check if batteries are properly charged and installed.

Charge Batteries after each use.

Always ride on dry paved surfaces.
Gravel, wet, extreme
incline, and uneven surfaces are a hazard.
Check if all tires are properly inflated.
2
3
List of Parts
List of Parts
Multi-Point
4
Multi-Point
1
Throttle
2
Multi-function Instrument
3
Brake lever
4
Alloy handlebar tub
5
Quick release
6
Connecting tube
7
Seat
8
Charger port
9
Footboard
10
Rear wheel
11
Battery
12
Power connecting plugs
13
Allen set screw
14
Front fender compartment
15
Front fork
16
Motor
17
Front wheel
18
Basket
5
Tool Kits In The Tool Bag
Multi-Point
Front Bar
Multi-Point
1 Brake lever
1
Screwdriver
2
Allen wrench (2.5mm)
3
Allen wrench (3mm)
4
Allen wrench (5mm)
4 Multi-function Instrument
5
Allen wrench (6mm)
5 Key switch
6
Wrench (8 x 10mm)
7
Wrench (16 x 18mm)
8
Wrench (16 x 18mm)
9
charger
2 Lock mechanism switch
3 Horn switch
6 USB port
7 Throttle
6
7
Assembling The Multi-Point
Assembling The Multi-Point
Multi-Point
1. Unpack the Multi-Point carefully so that you
do not misplace any of the parts.
2. Place the Multi-Point on a flat, level surface.
Block the front up 3.5''. This will make the
next step easier
3. Remove the bolts and nuts from the
connecting tube clamp (B). Place the
connecting tube into the top opening (A).
After aligning the holes, place the two bolts
through the connecting tube and neck
assembly. Twist the bolts, do not hammer
them through. Tighten these two bolts with the
nuts provided.
8
Multi-Point
4. The two Allen set screws on the front of the
connecting clamp are for removing any play
after the bolts have been tightened. First,
back off the nuts, second, set the screws,
third, tighten the nuts to prevent the screws
from backing off.
Two Allen
set screws
5. Extend the handle bar tube to full upright
position, and slide it into connecting with the
front fork.
9
Assembling The Multi-Point
Assembling The Multi-Point
Multi-Point
*Note: The tube shaft is intentionally off center to
allow handlebars to fold to the side. Be sure to
align release button to pivot on brake handle side
6. Ensure that the handlebar is facing front, the
brake on the left side and the throttle on the
right, then tighten the handlebar tube collar
clamp using the enclosed 5mm wrench.
7. Plug in the two power connecting plugs into
the sockets. The design of each plug and
socket is different. Connect the ones which
best fit each other to finish the assembly.
10
Multi-Point
8. Match the pins of the plugs to the holes of
the sockets. Note the alignment notches.
NOTE: Handle bar height adjustment. Handle
bar height can be easily adjusted by opening the
quick release on the handlebar tube to preferred
height, then firmly closing quick release.
11
Charging The Batteries
Multi-Point
you ride the Multi-Point for the first time
you must charge the batteries for 4-6 hours using
only the supplied charger.
Charging The Batteries Outside Scooter
Multi-Point
●Before
●To
charge the batteries, plug the charger into the
charger socket located on the rear side of the
battery/controller compartment. Then plug the
charger into a wall outlet. Red light on charger
indicates charging, green light indicates charged.
1. Turn off the key switch.
2. Lift the floor mat. Unscrew two bolts that secure
the battery cover and remove it.
3. Unplug the battery connection plug, unlock the
battery case, remove the battery, and charge
using the optional external charge wire and
provided charger.
12
13
Charging The Batteries Outside Scooter
Multi-Point
Riding The Multi-Point
Multi-Point
●Once
you have completed the initial charge you
are ready to ride. Remember, this is not a toy. The
Multi-Point can reach speeds up to 16 mph
depending on the terrain and the weight of the
rider. You must wear a helmet and protective pads.
Be aware of all local laws and ordinances that
govern and/or restrict the use of powered scooters.
The laws and ordinances vary greatly from
municipality to municipality. It is your responsibility
to know and abide by your local restrictions.
●To ride, insert the key into the key switch and turn
the key in clockwise direction till the first click. The
battery gauge will be illuminated indicating that the
battery is in operation. If you want to turn on the
front light, please turn the key to the second click
in clockwise direction.
●Hold
onto the front bar with both hands. Your left
fingers will control the brakes and your right
14
15
Riding The Multi-Point
Multi-Point
Riding The Multi-Point
Multi-Point
hand will control the throttle. As you turn the
throttle towards yourself, the speed will be
increased. Release the throttle and apply the
brake to stop the scooter. You will control the
speed of the scooter by using both the throttle
and the brake. When the brake handle is
squeezed it cuts power off the throttle.
NOTE 1: WARNING: Never try stunts. Always
maintain a safe speed.
NOTE 2: When scooter is parked, please remove
the key, this will avoid anyone from accidentally
turning the throttle causing the scooter to speed
forward. Failure to do this could lead to an
accident.
NOTE 3: If you need to stop in an emergency or
kill power quickly, you can turn the key off.
NOTE 5: When you use reverse, the scooter must
be stopped, and then push the reverse switch to
“R”, the horn will send out a noise, then gently turn
the throttle to back up. Warning, do not twist
throttle to full power when in reverse. When
finishing reverse, push the reverse switch back to
“F”.
NOTE 4: Depending on skills of the driver, the
Multi-Point comes equipped with an adjustable
speed switch located at the back of the scooter by
the charge port which allows you to limit speed to
8mph or switch to max speed of 16 mph.
16
17
Riding The Multi-Point
Folding The Multi-Point
Multi-Point
Multi-Point
1. Turn off the key switch
NOTE 6: The Maximum output of USB part is 5V
1A.
2. Put the clamp ring to turn to one side.
3. Press the quick release to bottom.
18
19
Folding The Multi-Point
Maintenance
Multi-Point
4. Lift the connecting tube (which is also
attached to the handlebar tube).
Multi-Point
Battery: (for professional use only)
The RMB Multi-Point is powered by 4, 12 volt,
rechargeable
batteries
housed
in
a
single
compartment. Other than recharging, these
batteries need no maintenance. To prolong battery
life, recharge the battery after each use. You must
also charge your Multi-Point if it has not been used
5. Carefully place the handlebar tube on the
footrest frame
for 30 days or more. If you need to replace the
battery pack, it is located inside the battery
compartment on the footboard. To get to the
battery pack, remove the compartment cover by
loosening the screws. To remove the batteries
disconnect the wires from the battery terminals.
Replace the battery pack with a new one and
reconnect the wires. Follow the instructions on
charging batteries to charge the new batteries.
20
21
Wiring Diagram
Multi-Point
22
Wiring Diagram
Multi-Point
23
Trouble Shooting Guide
Trouble Shooting Guide
Multi-Point
Problem
The power light
on the
instrument
does not
illuminate when
the Multi-Point
is on.
Cause
1. Battery is
discharged.
2. Loose
connection
inside MultiPoint.
3. Fuse is blown.
4. The
instrument is
defective.
The power
indicator on the
instrument
illuminates but
Multi-Point still
does not work.
1. The throttle
handle is not
operating
properly.
24
Solution
1. Recharge your
Multi-Point.
2. Remove the
screws that hold the
battery compartment
cover and raise the
cover. Visually
inspect all wire
connections making
sure there are no
loose wires,
reconnecting those
that are.
3. Replace the fuse.
4. Replace the
instrument.
1. Replace the
throttle handle. Call
Customer Service to
order a new throttle
Multi-Point
When the brake
lever is
squeezed the
Multi-Point
does not stop.
Scooter is
losing speed.
1. The brakes
are not adjusted
properly.
1. Low battery
2. Battery is
defective.
3. Low tire
pressure.
25
1. Adjust the brake
by loosening the bolt
on the brake wheel,
pull the cable and
retighten the bolt.
1. Recharge your
battery for 4~6 hours.
2. Replace battery.
Call Customer
Service to order a
new battery.
3. air tires up to
correct pressure.
Warranty
Warranty
Multi-Point
The Limited Warranty does not cover or apply to
the following: Normal wear and tear; any damage,
failure and/or loss caused by accident, misuse,
neglect, abuse and/or failure to follow instructions
or warnings as stated on the product or in the
applicable owner’s manual or other printed
materials provided with the product; damage,
failure and/or loss caused by the use of the
product in any other manner for which such
products were not specifically designed.
RMB EV warrants the Multi-Point for six (6)
months
according
to
the
following
terms. Batteries and tires are warranted for three
(3) months. This warranty extends to the original
retail purchaser only and commences on the date
of the original retail purchase. Any part of the
RMB EV product manufactured or supplied by
RMB EV and found in the reasonable judgment of
RMB EV to be defective in material or
workmanship will be repaired or replaced by an
authorized RMB EV service dealer without charge
for parts or labor. RMB EV is responsible for the
expense of delivering the warranty replacement
parts. However, if the customer chooses not to
replace the parts, the expense of
26
Multi-Point
delivering the Multi-Point to the factory /
authorized service dealer for warranty work or
the expense of returning it back to the owner
after repair/ replacement will be paid for by the
owner. RMB EV’s responsibility in respect to
claims is limited to making the required repairs or
replacements and no claim of breach of warranty
shall be cause for cancellation or rescission of the
contract of sale of any RMB EV product. Proof of
date of purchase will be required by the dealer to
substantiate any warranty claim. An authorized
RMB EV service dealer must perform all warranty
work. The warranty is limited to thirty (30) days
from the date of purchase for any RMB EV product
that is used for rental demonstration, commercial
purposes, or any other income producing
purpose. This warranty does not cover any RMB
EV product that has been subject to misuse,
neglect, negligence or accident, or has been
operated in any way contrary to the operating
instructions as specified in RMB EV’s owner’s
manual. This warranty does not apply to any
damage to RMB EV products that is the result of
improper maintenance or to any RMB EV product
that has been altered or modified so as to
27
Warranty
Warranty
Multi-Point
Multi-Point
adversely affect the products operation,
performance, or durability, or that has been altered
or modified to change its intended use. This
warranty does not extend to repairs made
necessary by normal wear and or by use of parts
that are incompatible with RMB EV products. In
addition this warranty does not cover items that
experience normal wear and tear. RMB EV
reserves the right to improve the design of the
product without assuming any obligations to
modify any product previously manufactured. All
warranties are limited in duration to the six (6)
months warranty period. Any such implied
warranties including merchantability, fitness for a
particular purpose or otherwise are disclaimed in
their entirety after the expiration of the appropriate
thirty day warranty period. RMB EV’s obligation
under this warranty is strictly and exclusively
limited to the repair and replacement of defective
parts and RMB EV does not assume any other
obligation. Some states do not allow limitations
on how long an implied warranty lasts, so the
above limitation may not
apply to you. RMB EV assumes no responsibility
for incidental consequential or other damages
including but not limited to expense of returning
28
the Multi-Point to an authorized service dealer
and expense of delivering it back to the
owner, mechanics travel time, telephone charges,
rental of a like product during the time the
warranty service is being performed, travel loss,
or damage to personal property, loss of revenue,
loss of time, or inconvenience. Some states do
not allow the exclusion or limitation of incidental
or consequential damages so the above
limitations may not apply to you.
WHAT RMB EV WILL DO:
RMB EV will, at its sole option, either repair,
replace or refund the purchase price of any unit
that does not conform to this limited warranty.
RMB EV may choose at its option to use
functionally equivalent reconditioned, refurbished
or new units or parts or any units. You are
responsible to get the unit back to RMB EV.
29
Instructions for optional attachments
Multi-Point
Warranty
Multi-Point
HOW TO GET WARRANTY SERVICE:
Installing the optional dc to ac inverter
1. Turn off the key switch
2. Remove seat post from seat
To obtain warranty service, please call or fax to
the following telephone numbers for RMB EV
Customer Service - warranty repair
Tel. 1-707-568-3333 or Fax.1-707-526-1409,
Email: info@rmbev.com
3. Install special seat post on seat
DO NOT RETURN YOUR PRODUCT TO ANY
ADDRESS.
Please call, email, or write for the location of the
RMB EV authorized service center nearest you
and for the procedures for obtaining warranty
claims.
30
4. Install special tube on scooter, put one side
with hole forward, and fasten bolts
31
Instructions for optional attachments
Instructions for optional attachments
5. Put floor mat through tube, and align nipples
to corresponding holes in floor deck
7. Install quick release, seat
Multi-Point
6. Put tube set through tube, put one side with
hole forward, and tighten with bolts
32
Multi-Point
8. Plug the up connector into the inverter socket,
plug the down connector into the charger
socket
33
Instructions for optional attachments
Multi-Point
Instructions for optional attachments
Multi-Point
9. When using the inverter, turn on the power
switch.
Inverter specification:
● Input voltage is DC 48V
● Output voltage is AC 110V 60Hz
NOTE 1: Do not expose to water drip or spray.
NOTE 2: Shock hazard. Keep away from children
● Do not insert foreign objects into the inverter's
ac outlet or vent openings.
● Do not under any circumstances. connect the
inverter to power utility AC distribution wiring.
● Failure to follow the above instructions may
result in personal injury or damage to the
inverter.
NOTE 3: Do not expose the inverter to
temperatures in excess of 104’F(40℃).
34
How to install the trailer
1. Turn off the key switch
2. Put the trailer tongue into the slot, after
aligning the holes, place the two bolts through the
holes. Twist the bolts, and tighten them with the
nuts provided.
3. Place the trailer connection plate (A) into the
trailer connection frame (B) of front of trailer
tongue. After aligning the holes, place the trailer
pin through the hole. Secure the trailer pin with
the cotter pin.
35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising