RFXtrx User Guide

RFXtrx User Guide
RFXtrx
USB RF transceiver
User guide
www.rfxcom.com
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 1 / 46
1. Table of Contents
1.
2.
Table of Contents ................................................................................................................ 2
RFXtrx general information .................................................................................................. 3
2.1. RFXtrx315 supported protocols .................................................................................... 3
2.1.1. RFXtrx315 configured for 310MHz ........................................................................ 3
2.1.2. RFXtrx315 configured for 315MHz ........................................................................ 3
2.1.3. RFXtrx868X .......................................................................................................... 3
2.2. RFXrec433, RFXtrx433, RFXtrx433E supported protocols ........................................... 4
2.2.1. By function ............................................................................................................ 4
2.2.2. Alphabetic list ........................................................................................................ 8
2.3. undec on .................................................................................................................... 13
2.4. Sensitivity influenced by enabled protocols ................................................................ 14
2.5. RF range reduction..................................................................................................... 15
2.6. Home Automation software ........................................................................................ 15
2.7. Dimensions ................................................................................................................ 15
2.8. Electrical .................................................................................................................... 15
2.9. Environmental conditions ........................................................................................... 15
3. Install the USB driver ......................................................................................................... 16
4. Run RFXflash on Linux under Mono .................................................................................. 16
5. RFXmngr test program ...................................................................................................... 17
5.1. Receiver ..................................................................................................................... 18
5.2. Transmitter ................................................................................................................. 19
6. Flash update of the RFXtrx ................................................................................................ 20
6.1. Update firmware in the RFXtrx ................................................................................... 20
6.2. Update firmware in the RFXtrx step by step ............................................................... 21
7. RFXtrx433 special device codes ....................................................................................... 23
7.1. Remote commands .................................................................................................... 23
7.1.1. X10 RF Remote .................................................................................................. 23
7.1.2. ATI Remote Wonder............................................................................................ 24
7.1.3. ATI Remote Wonder Plus .................................................................................... 25
7.1.4. Medion Remote ................................................................................................... 26
7.2. Harrison address conversion to switch settings .......................................................... 27
7.3. Flamingo, AB400, IMPULS, Sartano, Brennenstuhl switch settings............................ 28
7.4. Energenie 5-gang 429.950 ......................................................................................... 29
7.5. Phenix, IDK YC-4000S switch settings ....................................................................... 30
7.6. HE105 switch settings ................................................................................................ 31
7.7. HQ COCO-20 ............................................................................................................. 32
7.8. MDREMOTE V106, V107 ........................................................................................... 33
7.9. MDREMOTE V108, EKAB-10KRF ............................................................................. 33
7.10.
Aoke relay............................................................................................................... 33
7.11.
SEAV TXS4 ............................................................................................................ 34
7.12.
How to find the dx.com RGB LED strip driver ID ..................................................... 34
7.13.
How to find the dx.com RGB LED strip driver ID (rev. 2) ......................................... 34
7.14.
How to find the Eurodomest ID ............................................................................... 34
8. Blyss commands ............................................................................................................... 35
9. Somfy RTS ........................................................................................................................ 35
10.
BlindsT6......................................................................................................................... 36
11.
Lucci Air fan ................................................................................................................... 36
12.
Transmit undecoded ARC commands. .......................................................................... 37
13.
Known Lighting4 devices ............................................................................................... 38
13.1.
Proluxx projection screen ........................................................................................ 38
13.2.
Kingpin (KP100) projection screen .......................................................................... 38
13.3.
Mercury remote control mains sockets.................................................................... 38
13.4.
Conrad 034911 sockets .......................................................................................... 38
14.
FAQ ............................................................................................................................... 39
14.1.
Receive has stopped suddenly but transmit works.................................................. 39
14.2.
Can I increase the receive/transmit range of the RFXtrx? ....................................... 39
14.3.
The RFXtrx USB connection disconnects sometimes. ............................................ 39
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 2 / 46
14.4.
I have a 433.92MHz sensor/remote but this device is not received. ........................ 39
14.5.
The wall plug is switched by the remote. The remote is received but the RFXtrx does
not switch the module. .......................................................................................................... 39
15.
EC Declaration of Conformity......................................................................................... 40
16.
Warning: ........................................................................................................................ 41
17.
License .......................................................................................................................... 41
18.
Copyright notice ............................................................................................................. 41
19.
Revision history ............................................................................................................. 42
2. RFXtrx general information
The RFXtrx transceivers and RFXrec receivers are communicating over an USB port with the
Home Automation application. The RFXtrx/rec is powered by the USB port.
At startup the RFXtrx enters for 2 seconds the boot loader (red LED is on) and after this it starts
the receive/transmit firmware. If valid (decode-able) packets are received the yellow LED will
blink.
The RFXtrx315 and the RFXrec433 are mainly for use in the US. The RFXtrx315 can receive
US X10 lighting and security sensors or US Visonic PowerCode sensors at 315MHz.
The RFXrec433 can receive weather sensors of different brands at 433.92MHz.
The RFXtrx433 is a transceiver (transmitter+receiver) and can receive and control a large
number of sensors and other devices.
The RFXtrx433E is an extended RFXtrx433 transceiver.
Note: the listed protocols and brands are supported!
2.1.
RFXtrx315 supported protocols
2.1.1. RFXtrx315 configured for 310MHz
Protocol
Protocol receive transmit
US X10 lighting
US X10 security
X10
X10
Y
Y
Y
Y
Protocol
receive
transmit
-
-
Y
Keeloq
Visonic
Visonic
Y
Y
Y
Y
Protocol
receive
transmit
Keeloq
Visonic
Visonic
Y
Y
Y
Y
Y
Y
Y
-
2.1.2. RFXtrx315 configured for 315MHz
Protocol
Aoke relay
- http://www.aliexpress.com/store/product/whose-sale-prices-DC12V10A-LearningCode-Wireless-Remote-Control-Switch-System-1-Receiver-and-1Transmitter/1211856_1774391429.html
Keeloq (unencrypted part only)
Visonic CodeSecure (unencrypted part only)
Visonic PowerCode
2.1.3. RFXtrx868X
Protocol
FS20
Itho CVE RFT
Keeloq (unencrypted part only)
Visonic CodeSecure (unencrypted part only)
Visonic PowerCode
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 3 / 46
2.2.
RFXrec433, RFXtrx433, RFXtrx433E supported protocols
2.2.1. By function
Curtains, shades, projection screen, awning, gate openers
A-OK blind motors (RF01,AC114,AC123 controlled) - http://www.motorisationplus.com/
ASA ETR blind motors - http://www.asa-mingardi.org/en/home.php
ASP blind motors - http://www.asp-distribution.com/site%20volet/voletrenovation.aspx
BOFU blind motors - http://www.bofumotor.com/
BTX blind motors – http://www.btxinc.com
Brel blind motors - http://www.brel-motors.nl/webshop/motoren/
Chamberlain CS4330CN http://www.chamberlain24.de/epages/es122868.sf/en_GB/?ObjectPath=/Shops/es122868/Products/RA4336
Confexx CNF24-2435
Dolat DLM-1 controlled motors - http://www.dolat.com.cn/product1.asp?id=538
Dooya blind motors, remotes tested: DC305,DC306,DC307,DC313,DC1650,DC1651
Ematronic - http://www.ematronic.com/moteurs-volet-roulant/
ESMO blind motors
Forest blind/curtain motors - http://www.forestgroup.nl/index_nl.html
Harrison curtain – http://www.harrison.nl/home2.htm
Hasta blind motors - http://www.hasta.se/
JVS screens - http://www.screen-discount.nl/
Kingpin KP100 projection screen
Louvolite one touch motorised blinds
Luxaflex (RFXtrx433E only) - http://www.luxaflex.se/produkter/luxaflex/rullgardiner/
Media Mount Projector screen
Motolux - http://www.motolux.com.au/
Proluxx projection screen
Quotidom - http://www.quotidom.com/moteur-tubulaire-radio-quotidom-10-ou-20-nm-volet-roulant-ou-store-banne.html
RAEX blind motor (YR1326 controlled)
RohrMotor24 RMF blind motors - http://www.rohrmotor24.eu/rohrmotor24
RollerTrol blind motors - http://rollertrol.com/
Simu (RFXtrx433E only) – http://www.simu.com/
Somfy (RFXtrx433E only) – http://www.somfy.co.uk/
Sunpery blind motors
YOODA blind motors – http://www.sukcesgroup.pl
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 4 / 46
Temperature, humidity, weather sensors
Alecto – WS1200, WS1700, WS3500, WS4500
Auriol – H13726
Banggood – SKU174397
http://www.banggood.com/433MHz-Wireless-Weather-Station-Digital-Thermometer-Humidity-Sensor-p-965559.html
Cresta
Digimax
Hama – EWS1500
Hideki weather sensors
Honeywell – TF-ATS34C
Inovalley SM80 with plant probes - http://www.inovalley.com/detail.php?item_id=289
La Crosse
Lexibook – SM883
Maverick ET-732, ET-733 BBQ/Smoke temperature
Meade – TS33F-M, TS34C-M http://www.meade.com/products/weatherstations/sensors.html
Meteoscan – W155, W160
NEXUS – I008T
mi.sol WH2 http://www.ebay.com/itm/Transmitter-for-Wireless-Weather-Station-wireless-temperature-sensor-/121664060899
Opus XT300 /Imagintronix Soil sensor http://www.plantcaretools.com/en/webshop/wireless-moisture-sensor-en-detail
http://www.ebay.co.uk/itm/Wireless-Soil-Moisture-Sensor/251380900939?pt=UK_Home_Garden_Garden_Plants_Fertiliser_CV&hash=item3a8778244b
Oregon Scientific / Huger
Prego P-8426 http://www.sunmarket.fi/tuote.asp?TID=11990
Proove –TSS320 & TSS330 fridge/freezer thermometer & outdoor sensors 311346,311501
RFXSensor
RUBiCSON – stektermometer 48659, 48695 -pool sensor p48019
Sunvic TLX1206
Sunvic TLX7506
TechnoLine/Proficell http://www.elv.de/output/controller.aspx?cid=74&detail=10&detail2=27621
TFA
UPM/Esic (very short receiving range)
Ventus – WS155
Viking
WT0122 pool thermometer
Xiron –EN6
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
- TX95-TH
page 5 / 46
Appliance modules, dimmers, relays, LED controllers
ANSLUT (learning mode)
Aoke relay http://www.aliexpress.com/store/product/whose-sale-prices-DC12V10A-Learning-Code-Wireless-Remote-Control-SwitchSystem-1-Receiver-and-1-Transmitter/1211856_1774391429.html
Avantek
ByeByeStandBy
Blyss lighting – http://www.castorama.fr/store/Prise-telecommandee-et-telecommande-BLYSS---Interieur-prod4470026.html
Brennenstuhl
Chacon – http://www.chacon.be/
CoCo – http://www.coco-technology.com/en/home/
Conrad RSL2 – http://www.conrad.com/ce/en/product/640466/FUNK-STECKDOSENSCHALTER-RSLR2
DI.O – http://www.di-o.be/
DomiaLite
Ebode
ELRO AB400/AB600 – http://www.elro.eu/en/products/cat/home-automation/home-control1
Energenie ENER010 – 429.935, 5-gang 429.950 - https://energenie4u.co.uk/
Etekcity –http://etekcity.com/p-300-5-pack-wireless-remote-control-outlet-switch-set-with-2-remote-controls-zap-5lx.aspx
Eurodomest NL – Action
Everflourish EMW100
Flamingo
Flamingo FA500D FA500DSS
Home Confort – http://www.home-confort.net/en
HomeEasy EU – http://www.elro.eu/en/products/cat/home-automation/
HomeEasy UK (including HE105 relay) – http://www.homeeasy.eu/
HQ COCO-20
Ikea Koppla
Impuls – NL – Action
Intertechno – http://www.intertechno.at/
Kambrook RF3672 – http://www.bunnings.com.au/kambrook-4-piece-indoor-powerpoint-kit-with-remote-control_p7030054
KlikAanKlikUit – http://www.klikaanklikuit.nl/home/
Legrand CAD radio – http://docdif.fr.grpleg.com/general/legrand-fr/NP-FT-GT/FA181DFR.pdf
LightwaveRF – http://www.lightwaverf.co.uk/
Livolo - http://www.livolo-france.com/fr/ http://nl.aliexpress.com/w/wholesale-livolo-touch-switch.html
Maplin http://www.maplin.co.uk/p/remote-controlled-mains-socket-set-single-n78ka (use Lighting1 – COCO GDR2)
MDremote LED dimmer V106, V107, V108, EKAB-10KRF - www.ultraleds.co.uk
- http://www.ledstripkoning.nl/accessoires/dimmers-wit/draadloze-dimmer-10-knops-rf/
Mercury appliance modules – http://mercury.avsl.com/product?range=ME5124
NEXA – http://www.nexa.se/
ORNO
OTIO
Phenix
Philips SBC SP370 series
PROmax
Proove - http://proove.se/
RGB LED strip driver dx.com - http://www.dx.com/ order nbr: 130913 (new TRC02 not supported) ,
RisingSun
Sartano
Siemens (UK)
Waveman
X10 RTS10 / RFS10
X10 lighting
Xdom
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
67412
page 6 / 46
Door/window, smoke and other security sensors
Aidebao security
Alecto – SA30 smoke detector
AliExpress sensors with EV1572 or PT2262 (PT2262 is preferred)
Atlantic security
Chacon KD101 smoke detector
Chuango security
Eminent security
Flamingo KD101 smoke detector FA20RF, FA21RF
Meiantech security
NEXA KD101 smoke detector
Oregon MSR939 https://www.redealer.de/multimedia/home-living/wetterstationen/bewegungssensor-msr939/a-200667/
Visonic CodeSecure
Visonic PowerCode
X10 security
Remotes
ATI Remote Wonder
ATI Remote Wonder Plus
ATI Remote Wonder II
SEAV TXS4
X10 PC Remote
Chimes
1byOne Easy Chime
Byron SX chime - http://www.chbyron.eu/Byron/ByronSXRange/68/89/
Byron MP001
Chacon
Envivo – ENV1348
HomeEasy
KlikAanKlikUit
Profiles PAC-326R Belcanto
SelectPlus200689101 & SelectPlus200689103 (Action NL)
Power, gas water metering
Cartelectronic TIC and Encoder - http://www.cartelectronic.fr/
cent-a-meter
Electrisave
OWL CM113, CM180, CM119, CM160, CM180, CM180i - http://www.theowl.com/
Revolt NC5461 - http://www.pearl.de/a-NC5462-5452.shtml
RFXMeter
Specials
1byone Wireless Home Security Driveway Alarm http://www.1byone.co.uk/Home-Security/Alarms/O00QH-0511
DEA receivers http://www.deasystem.com/en/accessory/7/receivers (unencrypted only)
Lucci Air Fan - http://www.lucciair.com/
Mertik Maxitrol – Fire Place controllers
Oregon Scientific Body weight scales – BWR101, BWR102, GR101
Prego P-8426 – sauna temperature sensor http://www.sunmarket.fi/tuote.asp?TID=11990
Smartwares radiator valve http://www.homewizard.nl/smartwares-draadloze-radiatorkraan.html
Siemens SF01 - LF959RA50/LF259RB50/LF959RB50 extractor hood
Wave Design extractor hood
X10 Ninja/Robocam – camera motor
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 7 / 46
2.2.2. Alphabetic list
Important notes:
- Ext and Ext2 firmware will not operate in the RFXtrx433.
- RFXrec firmware is equal to RFXtrx433 – Type1 firmware without the transmit functions.
- Protocol enabling is only necessary for receive. Transmit protocols are always enabled.
Type
1
Type
2
Ext
Ext2
Protocol
rec
xmit
- http://www.1byone.co.uk/Home-Security/Alarms/O00QH0511
-
Y
Y
Y
ByronSX
Y
Y
1byone Easy Chime
A-OK blind motors RF01
-
Y
Y
Y
ByronSX
Y
Y
Y
Y
-
Y
BlindsT2
Y
Y
Y
Y
-
Y
BlindsT3
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Meiantech
Oregon
LaCrosse
Rubicson
AC
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Lighting5 Aoke
or Lighting1 ARC
N
Y
-
-
Y
Y
RFY
N
Y
ASP blind motors
- http://www.aspdistribution.com/site%20volet/voletrenovation.aspx
Y
Y
-
Y
BlindsT11
Y
Y
ATI Remote Wonder
ATI Remote Wonder Plus
ATI Remote Wonder II
Y
Y
-
-
-
ATI
ATI
Y
Y
Y
Y
Y
-
-
-
ATI
Y
-
Atlantic security
Auriol H13726
Auriol Z31055B-TX
Avantek
Y
-
Y
-
Y
Y
-
Y
Y
Y
Y
Y
Y
Y
-
-
-
Y
Y
Y*
Y
Banggood – SKU174397
ByeByeStandBy
Byron SX chime
Y
Y
Y
Y
Y
Y
Meiantech
Rubicson
Rubicson
Lighting5
*Lighting4
Rubicson
ARC
Y
Y
Y
Y
Y
Y
Y
ByronSX
Y
Y
-
-
Y
Y
Chime
Byron MP001
N
Y
Y
Y
Y
-
AE
Y
Y
- http://www.bofumotor.com/
* = receive only in Type2 used to get the remote ID.
Y
Y
Y
Y
BlindsT0
Y*
Y
Brennenstuhl
Brel blind motors – http://www.brel-
Y
Y
Y
Y
Lighting4
Y
Y
Y
Y
Y
Y
BlindsT6
N
Y
-
Y
-
-
BlindsT9
N
Y
-
-
-
Y
ATI/cartelectronic
Y
N
Y
Y
Y
-
Oregon
Y
-
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
ARC
Lighting1
Y
N
Y
Y
Device
1byone Driveway Alarm
- http://www.motorisationplus.com/
A-OK blind motors AC114,AC123
- http://www.motorisationplus.com/
Aidebao security
Alecto – SA30 smoke detector
Alecto – WS1200
Alecto – WS1700 and compatibles, WS3500, WS4500
ANSLUT (learning mode)
Aoke relay
- http://www.aliexpress.com/store/product/whose-saleprices-DC12V10A-Learning-Code-Wireless-Remote-ControlSwitch-System-1-Receiver-and-1Transmitter/1211856_1774391429.html
ASA ETR blind motors
- http://www.asa-mingardi.org/en/home.php
(only available in hardware version 1.0)
- http://www.chbyron.eu/Byron/ByronSXRange/68/89/
Byron MP001 chime
Blyss lighting
- http://www.castorama.fr/store/Prise-telecommandee-ettelecommande-BLYSS---Interieur-prod4470026.html
BOFU blind motors
motors.nl/webshop/motoren/
BTX blind motors – http://www.btxinc.com
Cartelectronic TIC and Encoder
- http://www.cartelectronic.fr/
cent-a-meter
Chacon (learning mode)
- http://www.chacon.be/
Chacon (with address code wheels)
Chacon EMW200
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 8 / 46
Chacon 54660 (equal COCO GDR2)
Y
Y
Y
Y
Y
Y
Y
Y
-
-
Y
Y
Y
Y
EMW200
Lighting1
COCO GDR2
always on
N
Y
Y
Y
-
BlindsT8
N
Y
Y
Y*
Lighting4
Y
Y
Y
Y
Y
AC
Y
Y
Y
Y
-
Y
Y
-
Y
Y
-
Y
Y
Y
ARC
Lighting1
COCO GDR2
BlindsT12
Y
N
N
Y
Y
Y
- http://www.conrad.com/ce/en/product/640466/FUNKSTECKDOSENSCHALTER-RSLR2
Y
Y
-
Y
RSL
Y
Y
Conrad RSL sensors
Conrad RSL2 motion/door-window sensors
Cresta
-
Y
Y
-
-
RSL
RSL
Y
Y
Y
Y
Y
Y
Y
Y
Hideki
Y
-
-
-
Y
-
KeeLoq
Y
Y
Y
Y
Y
-
X10
Y
-
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
ARC
Y
Y
-
Y
-
-
BlindsT10
N
Y
Y
Y
Y
Y
ARC
Y
Y
Y
Y
Y
Y
BlindsT6
N
Y
Y
Y
Y
Y
Y
Y
Y
-
X10
Oregon
Y
Y
Y
-
- http://www.elro.eu/en/products/cat/home-automation/homecontrol1
Y
Y
Y
-
Lighting4
Y
Y
ELRO AB600
Ematronic RF01
Y
Y
Y
Y
ARC
Y
Y
Y
Y
-
Y
BlindsT2
Y
Y
Y
Y
-
Y
BlindsT3
Y
Y
Y
Y
Y
Y*
Lighting4
Y
Y
- https://energenie4u.co.uk/
- ENER010 – 429.935, 5-gang 429.950
Y
Y
Y
-
Lighting1
Energenie Energenie5
N
Y
Envivo – Chime ENV1348
Y
Y
Y
Y
Y
Chime
Envivo
BlindsT6
N
N
Y
Y
Y
Y
Y
-
Lighting1
Energenie5
N
Y
* ARC only
Y*
Y
Y*
Y*
N
Y
Everflourish EMW100
Flamingo
Flamingo FA500D FA500DSS
Flamingo KD101 smoke detector FA20RF,
Y
Y
-
Y
Y
-
Y
Y
-
Y
Y
Lighting4
IT
N
Y
N
Y
Y
Y
Y
Y
Y
Y
always on
Y
Y
Y
Y
Y
Y
BlindsT7
N
Y
Y
Y
Y
Y
Y
Y
Rubicson
Curtain Harrison
Y
N
Y
Chacon KD101 smoke detector
Chamberlain CS4330CN
http://www.chamberlain24.de/epages/es122868.sf/en_GB/?
ObjectPath=/Shops/es122868/Products/RA4336
Chuango
* decoded as X10 in ext firmware
CoCo (learning mode)
- http://www.coco-technology.com/en/home/
CoCo (with address code wheels)
CoCo GDR2 (equal Chacon 54660)
Confexx CNF24-2435
Conrad RSL2
- TX-320, TS34C, anemometer, UV sensor, rain sensor
DEA receivers (unencrypted)
http://www.deasystem.com/en/accessory/7/receivers
Digimax
DI.O (learning mode)
- http://www.di-o.be/
DI.O (with address code wheels)
Dolat DLM-1 controlled motors
- http://www.dolat.com.cn/product1.asp?id=538
DomiaLite (with address code wheels)
Dooya blind motors, emulate remotes:
DC305,DC306,DC307,DC313,DC1650,DC1651
Ebode
Electrisave
ELRO AB400
- http://www.ematronic.com/moteurs-volet-roulant/
Ematronic AC114, AC123
- http://www.ematronic.com/moteurs-volet-roulant/
Eminent
* decoded as X10 in ext firmware
Energenie
ESMO blind motors
Etekcity – http://etekcity.com/p-300-5-pack-wirelessremote-control-outlet-switch-set-with-2-remote-controls-zap5lx.aspx
Eurodomest
(NL – Action)
FA21RF
Forest blind/curtain motors
- http://www.forestgroup.nl/index_nl.html
HAMA EWS1500
Harrison curtain
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
Lighting1
ARC
Or
Lighting5 Eurodomest
Lighting5 EMW100
page 9 / 46
- http://www.harrison.nl/home2.htm
Hasta new blind motors
- http://www.hasta.se/
* = receive only in Type2 used to get the remote ID.
Y
Y
Y
Y
BlindsT0
Y*
Y
Hasta old blind motors
Hideki weather sensors
Home Confort lighting
Y
Y
Y
Y
Y
Y
BlindsT1
Hideki
Y
-
Y
-
-
-
Y
-
HomeConfort
Y
Y
Y
Y
Y
Y
HE EU
Y
Y
Y
Y
Y
Y
Thermostat2 HE105
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
AC
ARC
Y
Y
Y
Y
Y
Y
Y
Y
Hideki
-
-
Ikea Koppla
Impuls (NL – Action)
Y
Y
Y
Y
Y
Y
Y
Lighting1
HQ COCO20
Lighting3
Lighting1
Impuls
N
N
N
Y
Y
Y
Inovalley SM80 with plant probes -
-
-
Y
Y
Rubicson
Y
-
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
ARC
BlindsT6
Y
N
Y
Y
http://www.bunnings.com.au/kambrook-4-piece-indoorpowerpoint-kit-with-remote-control_p7030054
-
Y
Y
-
Lighting2
Kambrook
N
Y
Kingpin KP100 projection screen
KlikAanKlikUit (learning mode)
Y
Y
Y
Y
Lighting4
N
Y
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
ARC
Y
Y
Y
Y
Y
Y
LaCrosse
Y
-
Legrand CAD radio
-
-
Y
-
Lighting5
LeGrand CAD
-
Y
Lexibook
Y
Y
Y
Y
Hideki
Y
-
Y
Y
Y
Y
AD
Y
Y
Y
Y
Y
Y
Lighting5 Livolo
N
Y
Y
Y
Y
Y
BlindsT0
Y*
Y
Lucci Air fan – http://www.lucciair.com/
-
-
Y
-
Fan
LucciAir
N
Y
Luxaflex –
-
-
Y
Y
RFY
N
Y
Y
Y
Y
Y
Lighting1
COCO GDR2
N
Y
Y
Y
Y
Y
Hideki
Y
-
Y
Y
Y
Y
Lighting5
MDRemote V106
N
Y
Y
Y
Y
Y
Lighting5
MDRemote V107
N
Y
Y
Y
Y
Y
Lighting5
MDRemote V108
N
Y
http://www.meade.com/products/weatherstations/sensors.ht
ml
Y
Y
Y
Y
Hideki
Y
-
Media Mount Projector screen
-
Y
-
-
Lighting4
N
Y
- http://www.home-confort.net/en
HomeEasy EU (learning mode)
- http://www.elro.eu/en/products/cat/home-automation/
HomeEasy UK – HE105
- http://www.homeeasy.eu/
HomeEasy UK (learning mode)
HomeEasy UK (with address code wheels)
Honeywell
- TF-ATS34C
HQ COCO-20
http://www.inovalley.com/detail.php?item_id=289
Intertechno (learning mode)
- http://www.intertechno.at/
Intertechno (with address code wheels)
JVS screens - http://www.screen-discount.nl/
Kambrook RF3672 –
- http://www.klikaanklikuit.nl/home/
KlikAanKlikUit (with address code wheels)
La Crosse
- TX2, TX3, TX3P, TX4, TX7, TX17, WS2300
- SM883
LightwaveRF
- http://www.lightwaverf.co.uk/
Livolo
- http ://www.livolonederland.nl/
- http://www.livolo-France.com/fr/
- http://nl.aliexpress.com/w/wholesale-livolo-touchswitch.html
Louvolite one touch motorised blinds
* = receive only in Type2 used to get the remote ID.
http://www.luxaflex.se/produkter/luxaflex/rullgardiner/
Maplin http://www.maplin.co.uk/p/remote-controlledmains-socket-set-single-n78ka
Maverick ET-732/733 BBQ/Smoke
temperature
MDremote LED dimmer V106
- www.ultraleds.co.uk
MDremote LED dimmer V107
- www.ultraleds.co.uk
MDremote LED dimmer V108, EKAB-10KRF
- http://www.ledstripkoning.nl/accessoires/dimmerswit/draadloze-dimmer-10-knops-rf/
Meade – TS33F-M, TS34C-M
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 10 / 46
Meiantech security
Mercury appliance modules
Y
Y
Y
Y
Meiantech
Y
Y
N
Y
Y
Y
Y
Y
Lighting1
Energenie5
- G6R-H4T1, G6R-H4T5, G6R-H4T ,G6R-H4TB, G6RH4T21-Z22
Y
Y
Y
Y
Mertik
Y
Y
Meteoscan W155,W160
Motorlux blinds motor
mi.sol WH2 http://www.ebay.com/itm/Transmitter-for-
Y
Y
Y
-
Y
Y
Rubicson
BlindsT3
Y
-
Y
Y
Y
Y
Y
FineOffset
Y
-
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
ARC
always on
Y
Y
Y
Y
Y
Y
Y
Y
Hideki
Y
-
Y
Y
Y
Y
XT300
Y
-
Y
Y
Y
Y
AC
Y
Y
Y
Y
Y
Y
Oregon
Y
-
Y
-
Y
Y
Oregon
Y
-
https://www.redealer.de/multimedia/homeliving/wetterstationen/bewegungssensor-msr939/a-200667/
-
-
Y
-
Oregon
Y
-
OTIO Lighting
OWL – CM113
OWL
Y
Y
Y
Y
Y
Y
-
RSL
Oregon
Y
Y
Y
-
- http://www.theowl.com/
- CM119, CM160, CM180, CM180i
Y
Y
Y
Y
Oregon
Y
-
Phenix
Philips SBC SP370 series
Prego P-8426
Y
-
Y
Y
Y
-
Y
-
Lighting4
Lighting1 Philips SBC
Y
N
Y
Y
Y
Y
Y
-
X10
Y
-
Y
Y
-
Y
Y
-
Y
Y
-
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
ByronSX
Lighting4
IT
FineOffset or
Rubicson
Y
-
radio-quotidom-10-ou-20-nm-volet-roulant-ou-storebanne.html
Y
Y
Y
Y
BlindsT6
N
Y
RAEX blind motor (YR1326 controlled)
Revolt NC5461
-
Y
-
-
BlindsT4
Y
Y
-
Y
-
-
RSL
Y
-
Y
Y
Y
Y
Y
Y
Y
Y
X10
X10
Y
Y
-
Y*
Y
Y*
-
AD
Y*
Y
- http://mercury.avsl.com/product?range=ME5124
Mertik Maxitrol Fire Place controllers
Wireless-Weather-Station-wireless-temperature-sensor/121664060899
NEXA (learning mode)
- http://www.nexa.se/
NEXA (with address code wheels)
NEXA KD101 smoke detector
NEXUS
- I008T
Opus XT300 /Imagintronix Soil sensor
http://www.plantcaretools.com/en/webshop/wirelessmoisture-sensor-en-detail
http://www.ebay.co.uk/itm/Wireless-Soil-Moisture-Sensor/251380900939?pt=UK_Home_Garden_Garden_Plants_Fert
iliser_CV&hash=item3a8778244b
ORNO
Oregon Scientific / Huger BBQ and weather
sensors
- AW129, AW131, BTHGN129, BTHR918, BTHR918N,
BTHR968, EW109, PCR800, RGR126, RGR682, RGR918,
RGR928, RTGN318, RTGR328N, RTGR328N, RTGR368N,
RTGR383, RTHN318, STR918, STR928, ,TGHN800,
TGHN801, THC138, THC238, THC268, THGN122NX,
THGN123N, THGN132ES, THGN132N, THGN500,
THGR122(N/NX), THGR228(N/NF), THGR238, THGR268,
THGR328N, THGR810, THGR918, THGR928,
THGRN228NX, THN122N, THN129, THN132N, THR128,
THR138, THR288(N/NF), THRN122N, THWR288A,
THWR800, UV138, UVN128, UVN800, UVR128, WGR800,
WGR918, WTGR800, WTGR800
Oregon Scientific weighting scales
- BWR101, BWR102, GR101
US BWR101, BWR102 in RFXrec
Oregon MSR939
http://www.sunmarket.fi/tuote.asp?TID=11990
Profiles PAC-326R Belcanto
Proluxx projection screen
PROmax
Proove –TSS320 & TSS330 fridge/freezer thermometer &
outdoor sensors 311346,311501
Quotidom – http://www.quotidom.com/moteur-tubulaire-
- http://www.pearl.de/a-NC5462-5452.shtml
RFXSensor
RFXMeter
RGB LED strip driver dx.com
- http://www.dx.com/ order nbr: 130913, (new TRC02 NOT
supported)
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 11 / 46
- http://www.dx.com/ order nbr: 67412
* = receive only in Type2 used to get the RGB remote ID.
RGB432W LED controller
RisingSun
RUBiCSON
Y
Y
Y
Y
Y
Y
Y
Lighting5 RGB432W
Lighting4
N
Y
Y
Y
Y
-
Y
Y
Rubicson
Y
-
Y
Y
Y
Y
BlindsT6
N
Y
- http://rollertrol.com/
* = receive only in Type2 used to get the remote ID.
Y
Y
Y
Y
BlindsT0
Y*
Y
Sartano
SEAV TXS4
SelectPlus200689101 &
SelectPlus200689103
Y
-
Y
-
Y
-
Y
Y
Lighting4
FAN SEAV TXS4
Y
N
Y
Y
-
Y
Y
Y
ByronSX
Y
Y
Siemens SF01 LF959RA50/LF259RB50/LF959RB50
extractor hood
-
Y
-
-
Fan
SF01
N
Y
Siemens (UK)
Simu / RTS (RFXtrx433E only) – http://www.simu.com/
Smartwares radiator valve
Y
-
Y
-
Y
Y
Y
Y
AD
RFY
Y
N
Y
Y
-
-
Y
Y
Radiator1
Smartwares
N
Y
-
-
Y
Y
RFY
N
Y
Sunpery blind motors
Sunvic TLX1206
Sunvic TLX7506
TechnoLine/Proficell
Y
Y
Y
Y
Y
Y
Y
-
BlindsT9
X10
X10
N
Y
Y
Y
Y
-
http://www.elv.de/output/controller.aspx?cid=74&detail=10&d
etail2=27621
- TX95-TH
Y
-
Y
Y
Rubicson
Y
-
Y
Y
Y
Y
Hideki
Y
-
-
-
-
Y
Oregon
Y
-
- WT260,WT260H,WT440H,WT450,WT450H,WDS500,
RG700
Y
-
-
-
Hideki
Y
-
Ventus WS155
Viking
-
-
Y
Y
Rubicson
Y
-
Y
Y
Y
Y
FineOffset
Y
-
Y
Y
Y
Y
-
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
Visonic
Visonic
Fan
SF01
Lighting1 Waveman
FineOffset
Y
Y
N
N
N
Y
Y
Y
Y
-
Y
Y
Y
Y
BlindsT6
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
X10
X10
X10
X10
X10
X10
Rubicson
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
- stektermometer 48659, 48695
-pool sensor p48019
RohrMotor24 RMF blind motors
- http://www.rohrmotor24.eu/rohrmotor24
RollerTrol blind motors
(Action NL)
- http://www.homewizard.nl/smartwares-draadlozeradiatorkraan.html
Somfy / RTS
- http://www.somfy.co.uk/
TFA
- TS15C, TS34C,external temperature sensor 30.3133,
anemometer 30.3149, UV sensor, rain sensor 30.3148, pool
sensor 30.3160
TFA
- pool sensor 30.3056.10, 30.3216.20
UPM/Esic (very short receiving range)
- 02035, 02038, 02811
Visonic CodeSecure
Visonic PowerCode
Wave Design extractor hood
Waveman
Westinghouse fan 7226640
WT0122 pool sensor
YOODA blind motors
- http://www.sukcesgroup.pl
X10 Ninja/Robocam
X10 PC Remote
X10 RTS10 / RFS10
X10 lighting
X10 security
Xdom
Xiron – EN6
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
Fan
page 12 / 46
2.3. undec on
This parameter is for internal use by RFXCOM only!!!
If new sensor types are released they will most probably not be decoded by the RFXtrx
firmware. For this reason we have added the option to enable receive of undecoded messages.
This function is only to enable RFXCOM to add this new sensor type in the firmware if possible.
If “undec on” is enabled in normal use the application will receive a lot of undecoded messages
mostly as a result of RF noise or disturbed RF packets.
Important: For normal use “undec on” should be disabled
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 13 / 46
2.4.
Sensitivity influenced by enabled protocols
The sensitivity of the receiver part is highly influenced by the number of protocols enabled.
Lesser protocols enabled will make the receiver more sensitive for the enabled protocols.
X10
ARC
AC
HomeEasy EU
Meiantech/Atlantic
Oregon
ATI
Visonic/Keeloq
Mertik
AD (LWRF)
Hideki/UPM
La Crosse
FS20
ProGuard
BlindsT0
BlindsT1/T2/T3
AE (Blyss)
Rubicson
FineOffset/Viking
Lighting4
RSL
Byron SX
Imagintronix
HomeConfort
Green = enabled by default
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 14 / 46
HomeConfort
Imagintronix/Opus
Byron SX
RSL/Revolt
Lighting4
FineOffset/Viking
Rubicson/Alecto
AE (Blyss)
BlindsT1/T2/T3/T4
BlindsT0
ProGuard
FS20
La Crosse
Hideki/UPM
AD (LWRF)
Mertik
Visonic/Keeloq
ATI
Oregon 3.0 / OWL
Oregon 2.1
Oregon 1.0
Meiantech/Atlantic
HomeEasy EU
AC
ARC
X10
There are a few protocols that will reduce or even eliminate receiving of other protocols if
enabled.
For example:
If the AD (LightwaveRF, Siemens) protocol is enabled it can stop receiving of Meiantech /
Atlantic, Oregon 3.0,Visonic and Mertik.
All other protocols are disabled if BlindsT0 is enabled.
2.5.
RF range reduction
The RF signals operating distance is reduced when the signal has to pass through walls.
2.6.
Home Automation software
For the list of Home Automation software that supports the RFXtrx see the web site
www.rfxcom.com
2.7.
Dimensions
The dimensions of the RFXtrx/RFXrec are: 83.5 x 42 x 15 mm
Total height from bottom to antenna top is 122mm
The dimensions of the RFXtrx433E are: 83 x 59 x 22 mm
Total height from bottom to antenna top is 130mm
2.8.
Electrical
The RFXtrx is powered by the 5 Volt of the USB interface.
Operating current;
Receive mode:
Transmit mode:
28 mA (0.14Watt)
45 mA
The RFXtrx Radiated RF power is 10dBm max.
2.9.
Environmental conditions
Normal operating:
Absolute min-max temperature:
15°C to 35°C
-10°C to 55°C
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 15 / 46
3. Install the USB driver
The RFXtrx has the FTDI FT232R USB interface chip installed.
The USB drivers are available at http://www.ftdichip.com/Drivers/VCP.htm
4. Run RFXflash on Linux under Mono
Open a Terminal screen in Linux (Ctrl-Alt-T)
Execute once:
Install Mono:
[sudo] apt-get install mono-runtime
Install VisualBasic support under Mono:
[sudo] apt-get install libmono-microsoft-visualbasic8.0-cil
If the USB device is created as ttyACMx you will need to create a link between
/dev/ttyACMx and a serial port /dev/ttySx.
This is not necessary if the device is created as /dev/ttyUSBx !!
[sudo] ln -sf /dev/ttyACM1 /dev/ttyS3
Note: sudo must be entered without brackets [ ]. sudo is required if not running as super user.
Launch the RFXflash.exe program.
[sudo] mono RFXflash.exe
Note: RFXmngr does not operate under mono!
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 16 / 46
5. RFXmngr test program
The RFXmngr program supports decoding of received data and allows you to transmit
commands.
After the connection the RFXmngr program transmits a Reset and Get Status command so that
it will know the RFXtrx type and configuration settings:
Transmitter protocols are always enabled but receiver protocols can be disabled. This is very
useful because the receiver will become more sensitive when protocols not used are disabled.
So select only the protocols to be used, click Set mode and click Save Settings.
Note that these settings are lost in Type1 and Type2 firmware after an update and need to be
set again.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 17 / 46
5.1.
Receiver
The RF protocols to be received can be configured on the Main tab at Set Mode.
Click Save Settings to save the selected protocols in non-volatile memory of the RFXtrx. This
configuration is now restored every time after a power up.
Note that these settings are lost after a firmware update and need to be set again.
Note: Protocol enabling is only necessary for receive. Transmit protocols are always enabled.
The received RF data is decoded and displayed in the yellow window.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 18 / 46
5.2.
Transmitter
The tabs after the Main tab are used to send commands to the transmitter.
For example Lighting1 is used to send X10, ARC and some more.
Note: Protocol enabling is only necessary for receive. Transmit protocols are always enabled.
Select Type to see which protocols are supported on the different tabs.
The transmitted commands are displayed in the yellow window including the acknowledge send
by the RFXtrx, in the example above “ACK, data correct transmitted“.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 19 / 46
6. Flash update of the RFXtrx
6.1.
Update firmware in the RFXtrx
Firmware is flashed in the RFXtrx using this procedure:
1. Depending on the RFXtrx type download the latest RFXtrx315_yy.hex,
RFXrec433_yy.hex or RFXtrx433_yy.hex firmware file.
2. Connect the RFXtrx to a Windows system or Linux under MONO
3. Stop any program that is connected to the RFXtrx.
4. Start the RFXflash program (version 4.0.0.0 or higher)
5. Select the USB RFXtrx COM port or TCP/IP port and click the CONNECT button,
(the red LED on the RFXtrx should switch on now)
6. Load the correct .hex firmware file for your RFXtrx,
7. Click the WRITE button,
8. Click the Normal Execution mode button.
IMPORTANT:
1. Do not interrupt the flash procedure when started.
2. It can happen that the flash procedure ends with a pop-up screen indicating errors.
Just disconnect the RFXtrx and start again at step 5 until the flash procedure if finished
without errors.
If the red LED does not switch on if you click the CONNECT button:
1. Check if you have selected the correct USB COM port.
2. If you have flashed the RFXtrx before and interrupted the flash procedure it is possible
that the RFXtrx does not enter the flash state. Contact support@rfxcom.com for help.
Note: Receiver Settings are lost in Type1 and Type2 firmware after an update and have to be
set again.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 20 / 46
6.2.
•
Update firmware in the RFXtrx step by step
Click the Connect to Device button.
The RFXtrx will automatically switch from normal mode to the bootloader now.
•
Click the Open HEX file button and load the RFXtrxyyy_xx.hex file
Be sure to load the latest firmware file for the RFXtrx.
yyy indicates the RFXtrx frequency, so load the RFXtrx433 for an RFXtrx433!
xx indicates the firmware version.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 21 / 46
•
Click the Write device button and the RFXtrx is flashed.
•
Click on the Normal Execution Mode button to set the RFXtrx to running mode.
Note: Receiver Settings are lost in Type1 and Type2 firmware after an update and have to be
set again.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 22 / 46
7. RFXtrx433 special device codes
7.1. Remote commands
7.1.1. X10 RF Remote
Dec
2
18
34
56
58
64
66
82
96
98
99
100
Hex
02
12
22
38
3A
40
42
52
60
62
63
64
Button
0
8
4
Rewind
Info
CHAN+
2
Ent
VOL+
6
Stop
Pause
112
113
114
115
116
117
118
119
120
121
123
124
125
70
71
72
73
74
75
76
77
78
79
7B
7C
7D
Cursor-left
Cursor-right
Cursor-up
Cursor-down
Cursor-up-left
Cursor-up-right
Cursor-down-right
Cursor-down-left
left mouse
left mouse-End
Drag
right mouse
right mouse-End
130
146
160
162
176
182
184
186
192
194
201
209
210
211
212
213
214
215
216
217
224
226
242
255
82
92
A0
A2
B0
B6
B8
BA
C0
C2
C9
D1
D2
D3
D4
D5
D6
D7
D8
D9
E0
E2
F2
FF
1
9
MUTE
5
Play
Menu
Fast Forward
A+B
CHAN3
Exit
MP3
DVD
CD
PC / Shift-4
Shift-5
Shift-Ent
Shift-Teletext
Text
Shift-Text
VOL7
Teletext
Record
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 23 / 46
7.1.2. ATI Remote Wonder
Dec
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Hex
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
Button
A
B
power
TV
DVD
?
Guide
Drag
VOL+
VOLMUTE
CHAN+
CHAN1
2
3
4
5
6
7
8
9
txt
0
snapshot ESC
C
^
D
TV/RADIO
<
OK
>
<E
v
F
Rewind
Play
Fast forward
Record
Stop
Pause
44
45
46
47
48
49
50
51
52
53
54
55
2C
2D
2E
2F
30
31
32
33
34
35
36
37
TV
VCR
RADIO
TV Preview
Channel list
Video Desktop
red
green
yellow
blue
rename TAB
Acquire image
Copyright 2011-2016, RFXCOM
56
57
58
112
113
114
115
116
117
118
119
120
121
124
125
RFXtrx Version 5.27
38
39
3A
70
71
72
73
74
75
76
77
78
79
7C
7D
edit image
Full screen
DVD Audio
Cursor-left
Cursor-right
Cursor-up
Cursor-down
Cursor-up-left
Cursor-up-right
Cursor-down-right
Cursor-down-left
V
V-End
X
X-End
page 24 / 46
7.1.3. ATI Remote Wonder Plus
Dec
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Hex
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
Button
A
B
power
TV
DVD
?
Guide
Drag
VOL+
VOLMUTE
CHAN+
CHAN1
2
3
4
5
6
7
8
9
txt
0
Open Setup Menu
C
^
D
FM
<
OK
>
Max/Restore Window
E
v
Copyright 2011-2016, RFXCOM
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
112
113
114
115
116
117
118
119
120
121
124
125
RFXtrx Version 5.27
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
70
71
72
73
74
75
76
77
78
79
7C
7D
F
Rewind
Play
Fast forward
Record
Stop
Pause
TV2
Clock
TV
VCR
RADIO
TV Preview
Channel list
Video Desktop
red
green
yellow
blue
rename TAB
Acquire image
edit image
Full screen
DVD Audio
Cursor-left
Cursor-right
Cursor-up
Cursor-down
Cursor-up-left
Cursor-up-right
Cursor-down-right
Cursor-down-left
Left Mouse Button
V-End
Right Mouse Button
X-End
page 25 / 46
7.1.4. Medion Remote
Dec
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Hex
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
Button
Mute
B
power
TV
DVD
Photo
Music
Drag
VOLVOL+
MUTE
CHAN+
CHAN1
2
3
4
5
6
7
8
9
txt
0
snapshot ESC
DVD MENU
^
Setup
TV/RADIO
<
OK
>
<E
v
F
Rewind
Play
Fast forward
Record
Stop
Pause
44
45
46
47
48
49
50
51
52
53
2C
2D
2E
2F
30
31
32
33
34
35
TV
VCR
RADIO
TV Preview
Channel list
Video Desktop
red
green
yellow
blue
Copyright 2011-2016, RFXCOM
54
55
56
57
58
112
113
114
115
116
117
118
119
120
121
124
125
RFXtrx Version 5.27
36
37
38
39
3A
70
71
72
73
74
75
76
77
78
79
7C
7D
rename TAB
Acquire image
edit image
Full screen
DVD Audio
Cursor-left
Cursor-right
Cursor-up
Cursor-down
Cursor-up-left
Cursor-up-right
Cursor-down-right
Cursor-down-left
V
V-End
X
X-End
page 26 / 46
7.2. Harrison address conversion to switch settings
The address used is converted to the address selected in the Harrison curtain motor using the
table below.
switch 1
H
A
0
B
0
C
0
D
0
E
1
F
1
G
1
H
1
I
1
J
1
K
1
L
1
M
0
N
0
O
0
P
0
2
H
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
3
H
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
4
H
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
X
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
6
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
7
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
8
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
H H H H = House code
X X X X = device code
Switch position in the motor:
Up
=1
Middle = not used!!!!
Down = 0
Examples:
If you assign the address E7 (1000 0110) to the curtain motor then set the switches to: 1=up,
2=down, 3=down, 4=down, 5=down, 6=up, 7=up, 8=down
If you assign the address A2 (0110 0001) to the curtain motor then set the switches to: 1=down,
2=up, 3=up, 4=down, 5=down, 6=down, 7=down, 8=up
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 27 / 46
7.3. Flamingo, AB400, IMPULS, Sartano, Brennenstuhl switch settings
Use type ELRO AB400D
Note that the HC (House Code A-P) is the house code used in programs and has no direct relation
with the A,B,C,D,E buttons on the remotes!
1 2 3 4
HC==========
A
0 0 0 0
B
0 0 0 1
C
0 0 1 0
D
0 0 1 1
E
0 1 0 0
F
0 1 0 1
G
0 1 1 0
H
0 1 1 1
I
1 0 0 0
J
1 0 0 1
K
1 0 1 0
L
1 0 1 1
M
1 1 0 0
N
1 1 0 1
O
1 1 1 0
P
1 1 1 1
<== switches
5 A B C D E
5 A B C D E
5 6 7 8 9 10
5 6 7 8 9 10
DC==================DC=============
1
0 0 0 0 0 0
33
0 0 0 0 0 1
2
0 0 0 1 0 0
34
0 0 0 1 0 1
3
0 0 1 0 0 0
35
0 0 1 0 0 1
4
0 0 1 1 0 0
36
0 0 1 1 0 1
5
0 1 0 0 0 0
37
0 1 0 0 0 1
6
0 1 0 1 0 0
38
0 1 0 1 0 1
7
0 1 1 0 0 0
39
0 1 1 0 0 1
8
0 1 1 1 0 0
40
0 1 1 1 0 1
9
1 0 0 0 0 0
41
1 0 0 0 0 1
10 1 0 0 1 0 0
42
1 0 0 1 0 1
11 1 0 1 0 0 0
43
1 0 1 0 0 1
12 1 0 1 1 0 0
44
1 0 1 1 0 1
13 1 1 0 0 0 0
45
1 1 0 0 0 1
14 1 1 0 1 0 0
46
1 1 0 1 0 1
15 1 1 1 0 0 0
47
1 1 1 0 0 1
16 1 1 1 1 0 0
48
1 1 1 1 0 1
17 0 0 0 0 1 0
49
0 0 0 0 1 1
18 0 0 0 1 1 0
50
0 0 0 1 1 1
19 0 0 1 0 1 0
51
0 0 1 0 1 1
20 0 0 1 1 1 0
52
0 0 1 1 1 1
21 0 1 0 0 1 0
53
0 1 0 0 1 1
22 0 1 0 1 1 0
54
0 1 0 1 1 1
23 0 1 1 0 1 0
55
0 1 1 0 1 1
24 0 1 1 1 1 0
56
0 1 1 1 1 1
25 1 0 0 0 1 0
57
1 0 0 0 1 1
26 1 0 0 1 1 0
58
1 0 0 1 1 1
27 1 0 1 0 1 0
59
1 0 1 0 1 1
28 1 0 1 1 1 0
60
1 0 1 1 1 1
29 1 1 0 0 1 0
61
1 1 0 0 1 1
30 1 1 0 1 1 0
62
1 1 0 1 1 1
31 1 1 1 0 1 0
63
1 1 1 0 1 1
32 1 1 1 1 1 0
64
1 1 1 1 1 1
<== switches
<== OR switches
Examples:
A1
0000000000
A15
0000111000
N2
1101000100
N11
1101101000
0 = switch off
1 = switch on
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 28 / 46
7.4. Energenie 5-gang 429.950
To know the codes to use open the remote and check the 1 to 5 jumpers connected.
If a jumper connection is open it is a 1. If connected it is a 0 (zero)
1 2 3 4
HC=========
A 0 0 0 0
B 0 0 0 1
C 0 0 1 0
D 0 0 1 1
E 0 1 0 0
F 0 1 0 1
G 0 1 1 0
H 0 1 1 1
I 1 0 0 0
J 1 0 0 1
K 1 0 1 0
L 1 0 1 1
M 1 1 0 0
N 1 1 0 1
O 1 1 1 0
P 1 1 1 1
jumper setting in the remote
If jumper 5 is open (1) than add 5 to the remote code.
Examples:
Jumper
12345
10000
10001
Button Code
1
1
I1
I6
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 29 / 46
7.5. Phenix, IDK YC-4000S switch settings
Use type ELRO AB400D
Note that the HC (House Code A-P) is the house code used in programs and has no direct relation
with the A,B,C,D,E buttons on the remotes!
HC
switch
1 2 3 4
============
A
0 0 0 0
B
0 0 0 1
C
0 0 1 0
D
0 0 1 1
E
0 1 0 0
F
0 1 0 1
G
0 1 1 0
H
0 1 1 1
I
1 0 0 0
J
1 0 0 1
K
1 0 1 0
L
1 0 1 1
M
1 1 0 0
N
1 1 0 1
O
1 1 1 0
P
1 1 1 1
DC
switch
5 A B C D
==============
1
0 0 0 0 0
2
0 0 0 1 0
3
0 0 1 0 0
4
0 0 1 1 0
5
0 1 0 0 0
6
0 1 0 1 0
7
0 1 1 0 0
8
0 1 1 1 0
9
1 0 0 0 0
10 1 0 0 1 0
11 1 0 1 0 0
12 1 0 1 1 0
13 1 1 0 0 0
14 1 1 0 1 0
15 1 1 1 0 0
16 1 1 1 1 0
17 0 0 0 0 1
18 0 0 0 1 1
19 0 0 1 0 1
20 0 0 1 1 1
21 0 1 0 0 1
22 0 1 0 1 1
23 0 1 1 0 1
24 0 1 1 1 1
25 1 0 0 0 1
26 1 0 0 1 1
27 1 0 1 0 1
28 1 0 1 1 1
29 1 1 0 0 1
30 1 1 0 1 1
31 1 1 1 0 1
32 1 1 1 1 1
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 30 / 46
7.6.
Unitnr
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
HE105 switch settings
HE105
1 2 3
0 0 0
0 0 0
0 0 0
0 0 0
0 0 1
0 0 1
0 0 1
0 0 1
0 1 0
0 1 0
0 1 0
0 1 0
0 1 1
0 1 1
0 1 1
0 1 1
1 0 0
1 0 0
1 0 0
1 0 0
1 0 1
1 0 1
1 0 1
1 0 1
1 1 0
1 1 0
1 1 0
1 1 0
1 1 1
1 1 1
1 1 1
1 1 1
switches
4 5
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 31 / 46
7.7. HQ COCO-20
Note that the HC (House Code A-P) is the house code used in programs and has no direct relation
with the A,B,C,D,E buttons on the remotes!
6 7 8 9 <== switches in module
HC==========
A
0 0 0 0
B
0 0 0 1
C
0 0 1 0
D
0 0 1 1
E
0 1 0 0
F
0 1 0 1
G
0 1 1 0
H
0 1 1 1
I
1 0 0 0
J
1 0 0 1
K
1 0 1 0
L
1 0 1 1
M
1 1 0 0
N
1 1 0 1
O
1 1 1 0
P
1 1 1 1
10 1 2 3 4 5
10 1 2 3 4 5 <== switches in module
DC==================DC==============
1
0 0 0 0 0 0
33
1 0 0 0 0 0
2
0 0 0 0 0 1
34
1 0 0 0 0 1
3
0 0 0 0 1 0
35
1 0 0 0 1 0
4
0 0 0 0 1 1
36
1 0 0 0 1 1
5
0 0 0 1 0 0
37
1 0 0 1 0 0
6
0 0 0 1 0 1
38
1 0 0 1 0 1
7
0 0 0 1 1 0
39
1 0 0 1 1 0
8
0 0 0 1 1 1
40
1 0 0 1 1 1
9
0 0 1 0 0 0
41
1 0 1 0 0 0
10 0 0 1 0 0 1
42
1 0 1 0 0 1
11 0 0 1 0 1 0
43
1 0 1 0 1 0
12 0 0 1 0 1 1
44
1 0 1 0 1 1
13 0 0 1 1 0 0
45
1 0 1 1 0 0
14 0 0 1 1 0 1
46
1 0 1 1 0 1
15 0 0 1 1 1 0
47
1 0 1 1 1 0
16 0 0 1 1 1 1
48
1 0 1 1 1 1
17 0 1 0 0 0 0
49
1 1 0 0 0 0
18 0 1 0 0 0 1
50
1 1 0 0 0 1
19 0 1 0 0 1 0
51
1 1 0 0 1 0
20 0 1 0 0 1 1
52
1 1 0 0 1 1
21 0 1 0 1 0 0
53
1 1 0 1 0 0
22 0 1 0 1 0 1
54
1 1 0 1 0 1
23 0 1 0 1 1 0
55
1 1 0 1 1 0
24 0 1 0 1 1 1
56
1 1 0 1 1 1
25 0 1 1 0 0 0
57
1 1 1 0 0 0
26 0 1 1 0 0 1
58
1 1 1 0 0 1
27 0 1 1 0 1 0
59
1 1 1 0 1 0
28 0 1 1 0 1 1
60
1 1 1 0 1 1
29 0 1 1 1 0 0
61
1 1 1 1 0 0
30 0 1 1 1 0 1
62
1 1 1 1 0 1
31 0 1 1 1 1 0
63
1 1 1 1 1 0
32 0 1 1 1 1 1
64
1 1 1 1 1 1
Examples:
Switch 6 7 8 9 0 1 2 3 4 5
====================
A1
0000000000
A15
0000111000
N2
1101000100
N11
1101101000
0 = switch off
1 = switch on
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 32 / 46
7.8.
MDREMOTE V106, V107
This MDREMOTE has been tested.
http://www.ultraleds.co.uk/mini-dimmer-with-rf-remote-control-12-or-24v-dc-12a-maximum.html
The RFXtrx433 can only transmit MDREMOTE commands.
Procedure to find the ID of the MDREMOTE: In RFXmngr enable the X10 protocol and enable
“Undec on”. Press a button on the MDREMOTE remote.
The undecoded message contains the ID in the 2nd and 3rd byte, for example:
UNDECODED NEC:20AF6801D1
The 2 bytes after 20 is the MDREMOTE ID, in this example AF 68
7.9.
MDREMOTE V108, EKAB-10KRF
This MDREMOTE has been tested.
- http://www.ledstripkoning.nl/accessoires/dimmers-wit/draadloze-dimmer-10-knops-rf/
Procedure to find the ID of the MDREMOTE: In RFXmngr enable the Lighting4 protocol and
enable “Undec on”. Press a button on the MDREMOTE remote.
The undecoded message contains the ID in the 2nd and 3rd byte, for example:
UNDECODED ARC:201A0703FCFC
The 2 bytes after 20 is the MDREMOTE ID, in this example 1A 07
7.10. Aoke relay
The Aoke 12V DC - 315MHz or 433.92MHz 1 channel relay is available at www.aliexpress.com
store No.110758. Indicate clearly the required frequency when ordering!
The 1 channel learning relays can be used, see the picture below.
For example, for 1 relay:
http://www.aliexpress.com/store/product/DC12V-1CH-wireless-switch-remote-control-systemremote-control-switch-for-guard-door-window-curtain/110758_936534863.html
or for 6 relays:
http://www.aliexpress.com/store/product/ak-DC12V-1CH-RF-rocker-switch-livolo-switch-system-inchina-j-12a-108d-smart-house/110758_1007306574.html
The jumper next to the learning button defines
to operating mode:
Open = momentary
1-2 = toggle mode
2-3 = on/off mode (to be used with the RFXtrx)
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 33 / 46
7.11. SEAV TXS4
The ID can be found using RFXmngr and enable only ByronSX and undec on.
Or calculate the ID:
A SW1 switch on = 1
|---------SW1------------|
1 2 3
4 5 6 7
8 9 10
0 x x x | x x x x | x x x 0 | 0 1 0 1
For example SW1 = on off on off on off on off on off
The ID will become:
|---------SW1-----------|
1 2 3
4 5 6 7
8 9 10
0 1 0 1 | 0 1 0 1 | 0 1 0 0 | 0 1 0 1
this is hex: 5 5 4 5
7.12. How to find the dx.com RGB LED strip driver ID
Valid for the TRC02 remote with 2 batteries.
Flash the RFXtrx433 with Type2 firmware to be able to receive the remote ID in RFXmngr.
In RFXmngr enable only the LightwaveRF (AD) protocol.
-----------------------------------------------Packettype
= Lighting5
subtype
= RGB TRC02
Sequence nbr = 5
ID
= FCC48B
Command
= On
Signal level = 8
The ID is: FC C4 8B
If necessary flash the RFXtrx433 back to Type1 or ext if Type2 does not support devices you
need. (See chapter 2.2)
7.13. How to find the dx.com RGB LED strip driver ID (rev. 2)
Valid for the TRC02 remote with 3 batteries and ebay.com 191481664563.
In RFXmngr enable only the Lighting4 protocol.
-----------------------------------------------Packettype
= Lighting4
subtype
= PT2262
Sequence nbr = 29
Code
= 161C84
The ID is: 16 1C
7.14. How to find the Eurodomest ID
You can assign a random ID to the Eurodomest. If you want to use the same ID as the remote you
can find the ID of the remote using RFXmngr.
Start RFXmngr and enable only the Lighting4 protocol.
Press a button on the remote and you will receive a message like:
-----------------------------------------------Packettype
= Lighting4
subtype
= PT2262
Sequence nbr = 12
Code
= 6DFE0F
The ID is: 6 DF E0
Note: Eurodomest can also be controlled using ARC.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 34 / 46
8. Blyss commands
Some Blyss devices, like the Blyss motors, require a special command sequence number. To
simplify it; 0,1,2,3,4,0,1,…
This sequence number is normally created by the Blyss remote but now also by the RFXtrx433.
If you use a Blyss remote and the application (Domoticz, DomotiGa, Homeseer…) does not sync
with the received Blyss command you will see that you need to send multiple commands with the
RFXtrx433 before the Blyss device will respond.
For example,
The Blyss remote transmits with the sequence numbers 0,1,2
If the RFXtrx433 transmits now with sequence number 0 it will not be seen by the Blyss device as
a valid command and at the time the RFXtrx433 transmits the commands 1,2,3 the command will
be detected as valid when it receives the command with sequence number 3.
The same is true for the remote. If you transmit commands with the RFXtrx433 and after that with
a Blyss remote you need to transmit several commands with the remote before the Blyss device
responds.
I guess the same behaviour will show if you use multiple Blyss remotes.
9. Somfy RTS
Somfy RTS* devices can only be controlled by the RFXtrx433E. (not with the RFXtrx433)
The RFXtrx433E version is an RFXtrx433 with additional hardware to enable the RFY protocol
used to control Somfy RTS.
The 433.42MHz transmitter in the RFXtrx433E is used for a reliable control of the Somfy RTS
devices over a large distance and through walls.
The RFXtrx433E 433.92MHz transmitter is used to control all other devices.
To pair the Somfy RTS device:
•
Select a unique ID and unitcode for the RFXCOM RFY device.
•
Disconnect power from all Somfy RTS devices except the device to pair.
•
Press the Program button > 2 seconds on the original Somfy remote until the Somfy device
responds.
•
Transmit a Program command with the RFXtrx433E. The Somfy RTS device should respond
indicating the pair command was successful.
The RFXCOM RFY remote is registered in the RFXtrx433E by sending a Program command.
Up to 40 RFXCOM RFY remotes can be registered in the RFXtrx433E.
Remotes can be erased from the RFXtrx433E using the RFXmngr program.
The Somfy RTS device can be controlled by any application as long as the same ID and Unit
Code are used.
For example if the RTS device is paired using RFXmngr with ID=1 02 03 and Unit Code 1, the
RTS device can be controlled with Homeseer using the same ID and unit code.
* Somfy RTS are registered trademarks of Somfy System, Inc.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 35 / 46
10. BlindsT6
To add a RFXtrx433(E) BlindsT6 device to the blinds motor:
1. press the "program" button twice on the original remote ==> 2 beeps
2. transmit the "confirm" command with the RFXtrx433(E) ==> 5 beeps
11. Lucci Air fan
Select the ID for switch settings:
ID
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Remote switches
1 2 3 4
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
0 = ON
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 36 / 46
12. Transmit undecoded ARC commands.
Plug-in modules or other equipment with a PT2262 can be controlled using Lighting4.
There are a lot of brands using the PT2262 and some of them use the same timing (350) as used
by the ARC devices but a different protocol definition.
Messages will be received as undecoded ARC messages if the protocol definition does not match
the definition of the ARC protocol. Remote commands are received as ARC commands with a
wrong house and device code and/or command code or as undecoded ARC messages if “undec
on” is enabled. Decoding of these remotes is therefore not possible because they overlap the ARC
protocol partly.
But transmitting these commands is possible using the Lighting4 command.
So if we receive this command UNDECODED ARC:18014403:
(18 is not used)
hex to binary table
0=0 0 0 0
1=0 0 0 1
2=0 0 1 0
3=0 0 1 1
4=0 1 0 0
5=0 1 0 1
6=0 1 1 0
7=0 1 1 1
8=1 0 0 0
9=1 0 0 1
A=1 0 1 0
B=1 0 1 1
C=1 1 0 0
D=1 1 0 1
E=1 1 1 0
F=1 1 1 1
0 1 4 4 0 3 = selection box 0000 0001 0100 0100 0000 0011
Not selected = 0, box selected = 1
And the Lighting4 command contains the same “undec code” 01 44 03:
Lighting4 command:09 13 00 04 01 44 03 01 5E 00
pulse timing is 350 = hex 015E
Another example:
For this command UNDECODED ARC:18014430 set on the Lighting4 tab in RFXmngr selection
box 1 to 24 to 0 1 4 4 3 0 = 0000 0001 0100 0100 0011 0000
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 37 / 46
13. Known Lighting4 devices
13.1. Proluxx projection screen
Use Lighting4 with a pulse timing of 360
UP
STOP
DOWN
RESET
1110
1110
1110
1110
1101
1101
1101
1101
0101
0101
0101
0101
1001
1001
1001
1001
0101
0101
0101
0101
0010
1000
0100
0001
ED
ED
ED
ED
59
59
59
59
52
58
54
51
13.2. Kingpin (KP100) projection screen
Use Lighting4 with a pulse timing of 1040
UP
STOP
DOWN
PROGRAM
1110
1110
1110
1110
0001
0001
0001
0001
0100
0100
0100
0100
0010
0010
0010
0010
0010
0010
0010
0010
0010
0100
1000
0001
E1
E1
E1
E1
42
42
42
42
22
24
28
21
13.3. Mercury remote control mains sockets
http://mercury.avsl.com/product?range=ME5124
Use Lighting4 with a pulse timing of 188
1 OFF
1 ON
01000100010101010011 1100
01000100010101010011 0011
2 OFF
2 ON
01000100010101011100 1100
01000100010101011100 0011
3 OFF
3 ON
01000100010101110000 1100
01000100010101110000 0011
4 OFF
4 ON
01000100010111010000 1100
01000100010111010000 0011
5 OFF
5 ON
01000100011101010000 1100
01000100011101010000 0011
13.4. Conrad 034911 sockets
http://www.conrad.nl/ce/nl/product/034911/Draadloze-schakelaarset-5-delig
Use Lighting4 with a pulse timing of 425
Off = last 2 digits: 00
ON = last 2 digits: 01
Group
I
II
III
IV
Unit
1 OFF
1 OFF
1 OFF
1 OFF
00
01
01
01
01
00
01
01
01
01
00
01
01
01
01
00
00
00
00
00
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
00
00
00
00
I
I
I
I
1
2
3
4
00
00
00
00
01
01
01
01
01
01
01
01
01
01
01
01
00
01
01
01
01
00
01
01
01
01
00
01
01
01
01
00
01
01
01
01
01
01
01
01
01
01
01
01
00
00
00
00
I
I
1 OFF
1 ON
OFF
OFF
OFF
OFF
00 01 01 01 00 01 01 01 01 01 01 00
00 01 01 01 00 01 01 01 01 01 01 01
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 38 / 46
14. FAQ
14.1. Receive has stopped suddenly but transmit works.
Most probably a sensor is transmitting constantly. This could be for example an X10 MS13 motion
sensor or weather sensor with almost empty battery. Or an outside weather sensor filled with
water. Or a remote with a button pressed.
Test the RFXtrx with a remote or sensor on another location (> 1km away) using RFXmngr on a
Windows system or laptop.
14.2. Can I increase the receive/transmit range of the RFXtrx?
First check chapter 2.5 for the best place for the RFXtrx antenna.
The switch board is not the best place for the RFXtrx because of all metal objects that will absorb
or reflect the RF signals.
It is also advised to place the RFXtrx far away from PC’s, routers, Raspberry PI … because of the
RF noise those products produce and this will reduce the receive range very much.
You can connect another 50ohm 70cm/433MHz antenna with more gain.
For example http://www.ebay.com/itm/290979680030
Install this antenna on a metal plate of at least 30 cm for optimum result.
14.3. The RFXtrx USB connection disconnects sometimes.
This happens mostly on Raspberry PI with a low quality power supply. Solution is to use a
powered USB hub with a good quality power supply.
It can also happen if the USB cable is running along a power cable and a power device is
switched on that produces a high power spike like TL. Solution is to separate the USB cable from
all other cables and/or use a powered USB hub with a good quality power supply.
14.4. I have a 433.92MHz sensor/remote but this device is not received.
Besides the frequency the used protocol and modulation type is also important.
See chapter 2 for the list of supported devices.
14.5. The wall plug is switched by the remote. The remote is received
but the RFXtrx does not switch the module.
The remote transmits several protocols. The protocol used by the wall plug is not received by the
RFXtrx but some other protocols are received.
Solution:
For the HomeEasy EU- HE8xx series: reset the module to remove all paired remotes and pair the
module with the RFXtrx433E and one of remote codes that is received.
For IT modules FA500/PROmax: Pair the RFXtrx433E with the module using an IT device and
select a random ID. The received remote code can be used to know if the module is switched by
the remote.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 39 / 46
15. EC Declaration of Conformity
EC Declaration of Conformity
RFXCOM declares that the product:
RFXtrx
Brand: RFXCOM
Type: RFXtrx433E
conforms with the essential requirements and other relevant provisions of
the following directives and complies with the following standards
applied:
R&TTE Directive 99/5/EC
EN 300 220-1 V2.3.1 (2010-02)
EN 300 220-2 V2.3.1 (2010-02)
Low-voltage Directive 2006/95/EC IEC 60950-1 (2005-12)
EMC Directive 2004/108/EC
Copyright 2011-2016, RFXCOM
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.4.1 (2002-08)
RFXtrx Version 5.27
page 40 / 46
16. Warning:
•
•
RF signals are possible disturbed and it has not been justified for this equipment at uses in
circumstances where life-threatening or dangerous situations are possible.
RFXCOM HARDWARE AND SOFTWARE IS NOT INTENDED FOR USE IN THE
OPERATION OF NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR COMMUNICATION
SYSTEMS, AIR TRAFFIC CONTROL SYSTEMS, LIFE SUPPORT MACHINES OR OTHER
EQUIPMENT IN WHICH THE FAILURE OF THE SOFTWARE COULD LEAD TO DEATH,
PERSONAL INJURY, OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE.
17. License
•
•
•
•
•
You are allowed to use RFXCOM software, protocols and Written Materials with RFXCOM
hardware only.
All copyright and other proprietary notices associated with RFXCOM software, protocols and
Written Materials shall be visible to all users.
You may not sell, distribute, loan, rent, lease, license, sublicense or otherwise assign or
transfer RFXCOM software or RFXtrx protocols or Written Materials unless expressly
authorized in writing by RFXCOM.
You may not use any RFXCOM device, software or protocol as part of an exclusive or
patented product without the express prior written permission of RFXCOM.
You may not alter, modify, adapt or create derivative works based on any part of RFXCOM
software or protocols or Written Materials in any way, including translating, reverse
engineering, disassembling or decompiling the software.
18. Copyright notice
•
•
•
All RFXCOM hardware, software, protocols and Written Materials are protected by copyright
laws, and may not be reproduced, republished, distributed, transmitted, displayed, broadcast
or otherwise exploited in any manner without the express prior written permission of RFXCOM.
Netherlands Copyright and international treaty provisions protect the SOFTWARE,
HARDWARE, RFXtrx protocols and Written Materials and shall be subject to the exclusive
jurisdiction of the Netherlands Courts
RFXCOM reserves all rights not expressly granted herein.
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 41 / 46
19. Revision history
Version 0.0 – August 18, 2011
Initial version.
Version 1.0 – October 30, 2011
RFXflash under Mono added.
Version 2.0 – December 30, 2011
Updated for the production version with FTDI USB chip
Version 2.1 – January 18, 2012
Link for ACM to serial port added in Linux instruction.
EC Declaration of Conformity added
Version 2.2 – February 8, 2012
Protocols overview added
Screen dumps updated
Version 2.3 – February 16, 2012
Novatys planned
Version 2.4 – February 25, 2012
General information updated
Version 2.5 – March 1, 2012
Chapter added how to run RFXmngr or RFXflash on Linux.
Version 2.6 – March 14, 2012
Code tables added
Cresta, UPM added
Version 2.7 – March 15, 2012
Flash procedure updated
Version 2.8 – March 31, 2012
Phenix table added
Version 2.9 – March 31, 2012
AB400 and Phenix address extended
Version 2.10 – April 16, 2012
Linux USB - tty configuration updated
Version 2.11 – May 14, 2012
List of supported protocols updated.
Version 2.12 – June 8, 2012
Chapter added how to run RFXmngr or RFXflash on Mac OS
Version 2.13 – July 15, 2012
List of supported protocols updated
Version 2.14 – August 4, 2012
List of enabled protocols influence added
RFXtrx315 added
Version 2.15 – August 18, 2012
Enabled protocols table changed
Version 2.16 – August 26, 2012
Rubicson stektermometer added
ATI Remote Wonder II added
Version 2.17 – August 28, 2012
Table “sensitivity influenced” updated
Version 2.18 – September 18, 2012
Chapter 2.3 updated: BlindsT0 disables all other protocols
Version 2.19 – September 25, 2012
RFXFlash version required changed to 4.0.0.0
Version 2.20 – September 28, 2012
RF range reduction guide added
Version 2.21 – October 18, 2012
BlindsT2 and BlindsT3 added
Version 2.22 – October 24, 2012
Sartano added
Version 2.23 – October 31, 2012
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 42 / 46
Sensitivity table updated
Version 2.24 – November 7, 2012
Protocol table extended with the protocols to enable for receive
Version 2.25 – November 14, 2012
HE105 switch settings added
Version 2.26 – November 28, 2012
undec on explained
Version 2.27 – December 4, 2012
Use of Lighting4 commands for undec ARC
Brennenstuhl added
Version 2.28 – December 18, 2012
Receiver tab removed from RFXmngr
Version 2.29 – December 27, 2012
Lighting4 receive added
Version 2.30 – January 1, 2013
Raex motor added
Version 3.00 – January 4, 2013
RFXtrx433 Type1/Type2 firmware added
Version 3.01 – February 4, 2013
Supported protocols list updated
Version 4.00 – February 21, 2013
Chapter 8 - Lighting4 screen updated for RFXmngr 11.0.0.0
Known Lighting4 chapter added
Version 4.01 – March 13, 2013
Receive of LaCrosse sometimes influenced by enabled Hideki
Version 4.02 – June 8, 2013
MDREMOTE LED dimmer added
Conrad RSL2 added
Energenie added
Version 4.03 – September 27, 2013
How to find the MDREMOTE ID (chapter 7.6)
WS1200 added
Byron SX Chime added
Version 4.04 – November 15, 2013
Maverick ET-732 added
Alecto SA30 added
Oregon EW109 added
Revolt added
Version 4.05 – December 5, 2013
Blyss command explanation added.
Lighting4 - Mercury added
Lighting5 – dx.com RGB LED controller added
Version 4.06 – December 27, 2013
Chapter 2.2 updated
Version 4.07 – February 10, 2014
Chapter 7.8 added: how to find the dx.com RGB LED strip driver ID
Version 4.08 – March 20, 2014
ARC and Oregon3.0 updated in table 2.4.
Energenie 5-gang 429.950 added
Version 4.09 – April 4, 2014
BlindsT6 - DC106, YOODA, Röhrmotor24 RMF added
Version 4.10 – April 7, 2014
BlindsT7 - Forest added
Version 4.11 – April 28, 2014
RGB LED – clarified AD is LightwaveRF
Version 4.12 – May 21, 2014
Kambrook RF3672 added
RFY protocol added
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 43 / 46
Somfy programming instructions added
Supported protocol list RFXtrx433 updated.
Protocol list by function added
Version 4.13 – May 31, 2014
Opus TX300/Imagintronix Soil sensor added
Version 4.14 – June 18, 2014
Prega sensor added
Conrad 34911 Lighting4 coding added
Version 4.15 – June 25, 2014
Kambrook, Rubicson, Viking supported in ext firmware
Number of RFY remotes increased from 16 to 30
Version 4.16 – June 29, 2014
RFXmngr cannot be used on Linux
Version 4.17 – July 3, 2014
CoCo GDR2 added
Version 4.18 – July 14, 2014
Opus TX300 link added
Version 4.19 – July 25, 2014
Aoke relay added
Version 4.20 – August 25, 2014
Enabling protocols clearified.
Version 4.21 – September 5, 2014
Meade sensors added
Oregon BTHGN129 sensor added
Version 4.22 – September 18, 2014
Eurodomest added (NL - Action)
Byron MP001 added
WT0122 added
Procedures added to find the Eurodomest and TRC02 ver2 ID
Version 4.23 – September 24, 2014
Proove TSS330 fridge/freezer sensor added
Version 4.24 – October 9, 2014
BlindsT0 added in ext firmware
Alecto WS1700 and compatibles added
Version 4.25 – December 13, 2014
Smartwares radiator valve added
Proove TSS320 sensor added
Version 4.26 – January 2, 2015
SelectPlus200689101 White Chime (Action NL) added
Version 4.27 – January 6, 2015
SelectPlus200689103 Black Chime (Action NL) added
Version 4.28 – January 7, 2015
Proove outdoor sensors 311346 & 311501 added
Etekcity Wireless Remote Control Outlet Switch (US)
Version 5.00 – January 10, 2015
Copyright message updated
License chapter added
RFXmngr information updated
Version 5.01 – February 27, 2015
Chapter 2.5 Lighting4 receive is reduced with HomeEasy EU enabled.
Chamberlain tubular motor added
Sunpery blind motors added
DEA Systems receivers added
Envivo ENV-1348 chime added
Alecto WS4500 added
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 44 / 46
Version 5.02 – March 18, 2015
1byOne Easy Chime added
BTX blind motors added
Dolat DLM-1 blind motors added
OTIO added
Version 5.03 – March 19, 2015
TFA 30.3160 pool sensor added
Version 5.04 – April 14, 2015
Chapter 4 updated with restrictions on Lighting4
Siemens SF01 LF959RA50/LF259RB50/LF959RB50 extractor hood added
Maplin N78KA added
Version 5.05 – May 2, 2015
Dooya blind motors added
Louvolite one touch motorised blinds added
Alecto WS3500 added
Version 5.06 – May 4, 2015
Current dx.com TRC02 LED drivers have a different protocol and are not supported.
Version 5.07 – June 1, 2015
WH2 temperature humidity sensor added
RGB LED controller http://www.ebay.com/itm/191481664563 (maybe dx.com 227892)
Version 5.08 – July 31, 2015
Oregon MSR939 added
ESMO blind motors added
Brel blind motors added
Blinds T6 type motors now also supported in Ext firmware
Supported devices table 2.2.2. updated
Version 5.09 – Aug 12, 2015
Luxaflex blind motors added
Version 5.10 – Aug 17, 2015
JVS screen motors added
Livolo NL link added
Version 5.11 – Aug 31, 2015
ASA motors added
Version 5.12– Sept 14, 2015
Home Confort added
Version 5.13– Oct 2, 2015
Oregon GR101 received in Type1 firmware
Conrad RSL sensors received in Type2 firmware
Version 5.14– Oct 7, 2015
Quotidom blinds motor added
Version 5.15– Nov 06, 2015
Banggood temp-hum sensor added
Legrand CAD radio added
Version 5.16– Nov 26, 2015
Proluxx codes corrected
Version 5.17– Dec 24, 2015
RFXflash procedure updated
Rubicson pool sensor 48.019 added
Inovalley SM80 plant sensor added
Lucci Air fan added
Version 5.18– Jan 1, 2016
1byone Drive Way alarm added
Version 5.19– Feb 6, 2016
Avantek added
ASP blinds motors BlindsT11 added
Maverick ET-733 added
Profiles PAC-326R Belcanto chime added
HQ COCO-20 added
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 45 / 46
Version 5.20– Feb 18, 2016
BlindsT12 Confexx CNF24-2435 added
IT FA500, PROmax… added
Ext2 fimware overview added in chapter 2
Auriol Z31055B-TX added
Chuango, Eminent security sensors added
Version 5.21– May 6, 2016
Cartelectronic TIC and Encoder added
FAQ chapter added
Version 5.22– May 14, 2016
Corrected: TX95 is using the Rubicson protocol
MDRemote V108 added
Version 5.23– June 10, 2016
Motolux blinds motor added
Auriol H13726, Hama EWS1500, Meteoscan W155/W160, Ventus WS155 added
FAQ updated
Version 5.24– June 21, 2016
Seav TXS4 added
Version 5.25– Aug 6, 2016
ORNO added
Version 5.26– Sept 6, 2016
Added: How to find the SEAV TXS4 ID
Version 5.27– Oct 09, 2016
Westinghouse fan 7226640 added
THN129 added
TFA 30.3056 pool sensor added
Copyright 2011-2016, RFXCOM
RFXtrx Version 5.27
page 46 / 46
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising