instruction manual
INSTRUCTION MANUAL
SK-100070
f INTRODUCTION A
Thank you for your choice of the SKYRC eN3, 100-240V AC, NiHM/NiCad fast charger. This unit is simple
to use but its operation does require some knowledge on the part of the user. Please read this entire
operating manual completely and attentively before using this product, as it covers a wide range of
information on operating and safety.
SKYRC eN3 NiMH/NiCad Charger is an economic, high quality 100-240V AC charger, designed for
charging NiMH and NiCad batteries from 4-8 cells. The circuit power is 20W and max charge current can
reach to 3A. There are four kinds of charge current 1A/2A/3A that can be selected. You could select the
proper charge current according to battery capacity.
AC 100-240V
Power Jack
Charge Current Switch
4 4) Connect battery lead to charger’s battery socket. >
5) The charger starts charging. The charge status LED will glow constant red.
6) When the battery is fully charged, the charge status LED will glow constant green.
7) Unplug the battery from the charger and the charge status LED will flash green which indicates the
charger is ready to charge another battery.
A\ CAUTION:
This diagram shows the
correct way to connect
your battery to the eN3
charger while charging.
Failure to connect as IN AN
shown in this diagram will | —— ‘ E
damage this charger. ? 4
= NiMH Battery
NU MO UTE
NiCad CHARGER
sky Ard
CONNECTION DIAGRAM
Charge Status LED Indicator
N y
Á CHARGE PROCEDURES
SKYRC eN3 comes with the built in power supply. You can connect the AC power cord to the AC socket
(100-240V AC) directly.
Please refer to following steps to charge the battery,
1) Insert the AC power cord into the charger.
2) Insert the AC cord into a wall socket (100-240V). The charge status LED will light for 1 second and
then flash green which indicates the charger is ready for charging.
3) Select the proper charging current 1A/2A/3A by the toggle switch.
How to calculate the charge time?
Charge Time (mins) =Battery Capacity (Ah)/Charge Current (A)
Capacity Charge Current Approximate Charge Time
1000mAh 1A 60 mins.
3000mAh 2A 90 mins.
3000mAh 3A 60 mins.
N J
- 4 -
a ÓN
EXPLANATION OF LED STATUS
LED STATUS
LED Flashes Green
LED Glows Red
LED Glows Green
CHARGE STATUS
The Charger is Ready
Battery Charging in Process
Battery is Fully Charged
* Error Message
The charge current can’t be changed during charging process. If you change it, the charge status LED will
flash red to alert you to the error. In this case, please disconnect the power cord from the wall socket and
unplug the battery from the charger. You need to restart the charger to make it work again.
Ne J
4
SPECIFICATION
AC Input 100-240V
Battery Type NiMH/NiCad
Cell Count 4-8 cells
Charge Current 1А/2А/ЗА+ 10%
Circuit Power 20W
Dimension 69.4x110.7x40.5mm
Weight 175g
Ne J
TT SET CONTAINS
O SkyRC eN3 Charger
O AC Power Cord
O 18AWG Wire Charging Cable
eN3 Е qm
NU MQUICIA
NiCad CHARGER
N
Tamiya charging cable
5201-0030-01
EC3 charging cable
5201-0034-01
Dean charging cable
5201-0012-01
Crocodile clip
charging cable
5201-0031-01
TRAXXAS charging cable JST/BEC charging cable Futaba RX charging cable
5201-0033-01 5201-0043-01 5201-0044-01
A RECOMMENDED ACCESSORIES В
N J
@ WARRANTY AND SERVICE >
We guarantee this product to be free of manufacturing and assembly defects for a period of one year
from the time of purchase. The warranty only applies to material or operational defects, which are present
at t he time of purchase. During that period, we will repair or replace free of service charge for products
deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any
damage or subsequent damage arising as a result of misuse, modification or as a result of failure to
\ observe the procedures outlined in this manual. À}
| LIABILITY EXCLUSION x
This charger is designed and approved exclusively for use with the types of battery stated in these
Instruction Manual. SKYRC accepts no liability of any kind if the charger is used for any purpose other
than that stated. We are unable to ensure that you follow the instructions supplied with the charger, and
we have no control over the methods you employ for using, operating and maintaining the device. For this
reason we are obliged to deny all liability for loss, damage or costs which are incurred due to the
incompetent or incorrect use and operation of our products, or which are connected with such operation
in any way. Unless otherwise prescribed by law, our obligation to pay compensation, regardless of the
legal argument employed, is limited to the invoice value of those SKYRC products which were
immediately and directly involved in the event in which the damage occurred. y
3.
(MM AND SAFETY NOTES В
® SKYRC eNa3 is suitable for charging rechargeable NiMH/NiCad batteries. Do not attempt to recharge
dry cells. Charging other types of batteries may cause fire or explosion.
® Never leave the charger unattended when it is connected to its power supply.
® The allowable AC input voltage is 100-240V AC. Never connect it to any other voltage.
® Protect charger from dust, dirt and damp.
® Never place the charger and batteries connected to it on any form of flammable surface. Never
operate the charger in the vicinity of inflammable material or gas.
® Ensure that there is an unrestricted airflow to and from the charger's cooling slots. Never place the
charger on a carpet or similar surface.
® Take great care to maintain correct battery polarity, and avoid shot-circuit. Read the battery
Ne manufacturer's instructions and adhere to them strictly. J
CONFORMITY DECLARATION
SKYRC eN3 satisfies all relevant and mandatory CE directives and FCC Part 15 Subpart B: 2008.
The product has been tested to meet the following technical standards:
Test Standards Title Result
Household and similar electrical appliances —. Safety —.
GE-LVD EN60335-2-29 Part 2-29: Particular requirements for battery chargers. Conform
Electromagnetic compatibility (EMC) - Part 3-3: Limits -
Limitation of voltage changes, voltage fluctuations and
EN61000-3-3 flicker in public low-voltage supply systems, for Conform
equipment with rated current 16 A per phase and not
subject to conditional connection.
Electromagnetic compatibility (EMC) —
EN61000-3-2 Part 3-2: Limits — Limits for harmonic current emissions Conform
(equipment input current <16 A per phase)
CE-EMC
Electromagnetic compatibility (EMC) -- Part 6-1: Generic
EN61000-6-1 standards - Immunity for residential, commercial and Conform
light-industrial environments.
Electromagnetic compatibility (EMC) -- Part 6-3:
EN61000-6-3 Genericstandards - Emission standard for residential, Conform
commercial andlight-industrial environments.
FCC-VOC FCC Part 15B Electromagnetic compatibility (EMC), Conduction Emission Conform
& Radiation Emission.
This symbol means that you must dispose of electrical devices from the general household
X waste when it reaches the end of its useful life. Take your charger to your local waste
collection point or recycling centre. This applies to all countries of the European Union, and to
« п... other European countries with a separate waste collection system. J
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
RoHs
FC CEB XE
7504-0298-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising