phoenix cruise bath floor mixer

phoenix cruise bath floor mixer
page 1 of 3
PHOENIX
CRUISE BATH FLOOR MIXER
71
30
808
770
852
30
230
130
SPECIFICATIONS
Recommended use
Domestic, hotel, commercial
Material
Brass
Fixing
To the floor
Pressure Rating
Minimum 150 kPa
Maximum 550 kPa
Temperature Rating
Maximum continuous working temperature 75°
Colour Availability
Chrome
Suitable Hot Water Units
Storage tank: yes
Continuous flow: yes
Gravity fed: no
Standards
AS/NZS 3718
Cleaning Recommendations
This bathroom product should not be cleaned with abrasive
materials eg. steel wool/scourers. Do not use any corrosive or
abrasive cleaning agents containing acids or scouring agents.
Bleaches can also discolour products and therefore should not
be used. Damage caused by any improper treatment is not
covered by the product warranty- refer to Warranty Conditions
on the last page.
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered
trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from
their range without prior notification. Dimensions and set-outs listed are correct at time of publication
however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 2
To see the complete Phoenix range go to
www.reece.com.au/bathrooms
page 2 of 3
PHOENIX
CRUISE BATH FLOOR MIXER
FLOOR MOUNTED BATH MI
INSTALLATION
INSTRUCTIONS
www.phoenixtapware.com.au
1
3
Recommended pit to be cast in concrete.
Option A
(200 mm hoses)
Pre-installed copper
or flexible hose
6
Place Large Mount Plate
above the pit and screw
M10 x 75 Dynabolts (4 off)
into pre-drilled
concrete.
PVC Tube
9
Remove Protective Cover.
Rotate and a
disired positi
secure the M
Push Down t
Mount Plate
Grub Screw
100mm
deep
Option B -
135 SQUARE
(APPROX.)
4
Timber floor (200 mm hoses)
Connect to pre-installed copper or flexible hose
Floor board
7a
Place Protective Cover Plate
onto Large Mount plate
and tighten with Nut M8.
Ensure flexible hoses
are protruding and
held in place.
Unscrew Mount Plate and
slide floor hoses through
the centre.
Push Cover Plate onto
Mixer Assembly.
FLOOR MOUNTED BATH MIXER INSTRUCTIONS
6
Floor joice
2
9
Remove Protective Cover.
19mm Particle
board spacer
Rotate and adjust the Mixer Assembly to
disired position. Fasten the Grub Screw to
secure the Mixer Assembly.
Push Down the Cover Plate over the
Mount Plate gently.
5
Screw 4 Hex Bolt into Large
Mount Plate.
Grub Screw
7b
Loosen grub screws
and screw lower swivel
connectors to flexible
hoses and screw upper
swivel connectors
to mixer copper tubes.
Connect upper and
lower swivel connectors
and tighten grub screws
8
Cut to size and place tiles around
Protective Cover.
Screw Mountplate onto
Mixer Assembly.
Place Mixer Assembly
onto tiles and tighten
up with Nut M8.
Cover
Plate
Mixer
Assembly
Water Supply
To ensure optim
satisfaction plea
- Maximum hot
- Recommende
- Recommende
upper swivel
connector x 2
lower swivel
connector x 2
Mount
Plate
Mixer
Assembly
If the water pres
500kPa, an app
fitted.
- Flush out all p
- If the water tem
tempering valv
- Installation sh
AS3500.1 or re
Failure to comp
For details on P
www.phoenixta
Maintenance
Do not use clea
scouring agent.
abrasive. Surfa
and clear water
cleaning agents
7a
Unscrew Mount Plate and
slide floor hoses through
the centre.
Push Cover Plate onto
Mixer Assembly.
MOUNTED BATH MIXER INSTRUCTIONS
7b
9
Cover
Plate
Mixer
Assembly
Loosen grub screws
Rotate
and adjust
and
screw lower
swivel the Mixer Assembly to
disired position.
connectors
to flexible Fasten the Grub Screw to
secure
the Mixer
hoses
and screw
upper Assembly.upper swivel
swivel
connectors
Push
Down the Cover Plateconnector
over thex 2
to Mount
mixer copper
Platetubes.
gently.
Connect upper and
lower swivel
lower swivel connectors
connector x 2
Grub
Screw
and
tighten
grub screws
Water Supply Requirements
To ensure optimum performance and customer
satisfaction please adhere to the following:
- Maximum hot water temperature 75°C.
- Recommended minimum working pressure 150kPa.
- Recommended maximum working pressure 500kPa.
Mount
Plate
8
nd
Screw Mountplate onto
Mixer Assembly.
Mixer
Assembly
Place Mixer Assembly
onto tiles and tighten
up with Nut M8.
If the water pressure exceeds or is likely to exceed
500kPa, an approved pressure limiting valve must be
fitted.
- Flush out all pipe work prior to installation.
- If the water temperature exceeds 75°C an approved
tempering valve must be fitted.
- Installation should comply with Australian standard
AS3500.1 or relevant local authority requirements.
Failure to comply with the above may void all warranties.
For details on Phoenix’s warranty policy refer to
www.phoenixtapware.com.au
Maintenance and Care
Do not use cleaning agents containing a corrosive acid or
scouring agent. Do not use cream cleaners, as they are
abrasive. Surfaces should only be cleaned with a cloth
and clear water of mild liquid detergent. Use of unsuitable
cleaning agents may damage the surface.
Water Supply Requirements
To ensure optimum performance and customer
satisfaction please adhere to the following:
- Maximum hot water temperature 75°C.
- Recommended minimum working pressure 150kPa.
- Recommended maximum working pressure 500kPa.
2
Plumbers, please ensure a copy of the installation
If the water pressure
exceeds
or is
likelyend
to exceed
instructions
is left
with
the
user for future reference
Mixer
500kPa, an approved pressure limiting valve must be
fitted.
- Flush out all pipe work prior to installation.
- If the water temperature exceeds 75°C an approved
IN0090_revA
QU
AL
7
YEAR
IT Y
TE
PHOENIX
CRUISE BATH FLOOR MIXER
E
page 3 of 3
G UARA
N
REECE PRODUCT QUALITY GUARANTEE
You have purchased a quality product from Reece Pty Ltd
ABN 84 004 097 090 (“Reece”). This product is covered by a
7 year replacement product warranty and a 12 month warranty
over spare parts and labour.
This warranty does not include faults caused by:
7 YEAR WARRANTY – DOMESTIC USE
This warranty covers faults in the product construction, material
and assembly. Products which are within 7 years from the
date of purchase, found upon inspection by an authorised
Reece representative, to be defective in construction, material
or assembly, will be repaired or exchanged with an equivalent
product free of charge. Replaced items become Reece’s
property. This warranty also covers any spare parts included
under “Manufacturer’s Provisions” below.
• Installation or part installation by the purchaser or any person
other than a LICENSED PLUMBER
Manufacturer’s Provisions
The following spare parts are covered by a 15 year warranty:
• Mixer Cartridge
Labour and Spare Parts
The labour for the replacement of products and spare parts
to which this warranty applies will be supplied by Reece or
relevant supplier using licensed plumbers engaged by Reece or
relevant supplier within 1 year from the date of purchase.
Spare parts other than those listed in the Manufacturer’s
Provisions above, which are within 1 year from the date of
purchase found upon inspection by an authorised Reece
representative to be defective in construction, material or
assembly, will be replaced free of charge.
Warranty Conditions
This warranty will apply only under all of the
following conditions:
• The item has been installed by a licensed plumber
• The item has been installed for and subjected to domestic
residential use only
• Failure is due to a fault in the manufacture of the product
• Proof of purchase (including the date of purchase)
is provided
• The installation of the product is in accordance with the
instructions provided
This warranty does not cover products purchased as an
ex-display without being fully checked and tested for sale by
the manufacturer.
Don’t risk it, use a licensed plumber.™
• Incorrect installation or installation not in accordance with
the instructions provided
• Normal wear and tear
• Inadequate or complete lack of maintenance
• Chemical, electrochemical or electrical influences
• Harsh detergents or abrasive cleaners used on
product finishes
1 YEAR WARRANTY – COMMERCIAL USE
‘Commercial’ use is all use other than for normal domestic
residential purposes, including use in non-business places as in
public buildings, schools, sports centres and in establishments
that contain private bathrooms with high frequency of use by
many individuals, such as hotels, motels, retirement villages
and hospitals.
The Commercial warranty covers this product against
manufacturing faults in the construction, material and assembly
of both the finished products and any spare parts for a period
of 1 year from the date of purchase. Products and spare
parts which are found upon inspection by an authorised
Reece representative to be defective in construction, material
or assembly will be repaired or exchanged free of charge.
Replaced items become Reece’s property. The labour for the
replacement of products and spare parts to which this warranty
applies will be supplied by Reece or relevant supplier using
licensed plumbers engaged by Reece or relevant supplier. The
Warranty Conditions and exclusions which apply to the noncommercial warranty also apply to this commercial warranty.
EXCLUSIONS
To the fullest extent permitted by law, Reece excludes all liability
for damage or injury to any person, damage to any property,
and any indirect consequential or other loss or damage.
CLAIM PROCEDURE
For all warranty queries customers are to contact the branch
where the product was purchased. These details can be found
on your purchase invoice.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
TAP.PHOENIX.T1.7YR
All replacement products will be available for collection without
charge to the customer at the nearest Reece branch to the
customer’s location, or elsewhere as agreed between the
customer and Reece.
• Unsuitable or improper use
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising