ERB-3209 Quick Guide

ERB-3209 Quick Guide
2D Image Barcode Reader
Quick Guide
Auto Identify Data Collect Technology Inc. (aidcti) reserves the right to make changes
in specifications and other information contained in this document without prior notice,
and the reader should in all cases consult aidcti to determine whether any such
changes have been made. The information in this publication does not represent a
commitment on the part of aidcti.
aidcti shall not be liable for technical or editorial errors or omissions contained herein;
nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated into another language without the prior written consent of aidcti.
Auto Identify Data Collect Technology Inc.
All rights reserved.
Web Address:
Microsoft® Windows® is a trademark or registered trademark of Microsoft
Corporation. Other product names or marks mentioned in this document may be
trademarks or registered trademarks of other companies and are the property of their
respective owners.
FCC Part 15 Subpart B Class B
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for
Use only shielded data cables with this system. This unit has been tested
with cables less than 3 meters. Cables greater than 3 meters may not meet
class B performance.
Caution: Any changes or modifications made to this equipment not
expressly approved by aidcti may void the FCC authorization to operate
this equipment.
The CE marking indicates compliance to 2004/108/EC EMC Directive with Standards
EN55022 CLASS B, EN55024, EN61000-3-2, EN61000-3-3. In addition, complies to
2006/95/EC Low Voltage Directive, when shipped with recommended power supply.
aidcti shall not be liable for use of our product with equipment (i.e., power supplies,
personal computers, etc.) that is not CE marked and does not comply with the Low
Voltage Directive.
Waste Electrical & Electronic Equipment
aidcti complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF
THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment
This product has required the extraction and use of natural resources for its roduction.
It may contain hazardous substances that could impact health and the environment, if
not properly disposed. In order to avoid the dissemination of those substances in our
environment and to diminish the pressure on the natural resources, we encourage you
to use the appropriate take-back systems for product disposal. Those systems will
reuse or recycle most of the materials of the product you are disposing in a sound
The crossed out wheeled bin symbol informs you that the product should not be
disposed of along with municipal waste and invites you to use the appropriate
separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems, please
contact your local or regional waste administration.
You may also contact your supplier for more information on the environ mental
performances of this product.
RoHS Statement
When ordered as RoHS compliant, this product meets the Electrical and Electronic
Equipment (EEE) Reduction of Hazardous Substances (RoHS) European Directive
Reading Techniques
Connecting to USB
The view finder projects an aiming beam that should be centered over the bar code,
but it can be positioned in any direction for a good read. Hold the scanner over the bar
code, press the button, and center the aiming beam on the bar code. The aiming
beam is smaller when the scanner is closer to the code and larger when it is farther
from the code. If the bar code is highly reflective (e.g., laminated), try to tilt the
scanner at an angle, the bar code could be scanned.
Standard Product Defaults
The following bar code resets all standard
product default settings.
Scan Mode
Bs ~PAPHHF. F3 ! Ed
Bs ~PAPPST. F3 F1 Ed
*Trigger Mode
Presentation Mode
Bs ~VSUFCR. F3 < Ed
Bs ~SUFBK29909. F3 J Ed
Bs ~SUFCA2. F3 : Ed
* = Default
Bs ~CRBENA0. F3 $ Ed
Bs ~CBRENA1. F3 , Ed
Bs ~CBRSSX0. F3 [ Ed
Bs ~CBRSSX1. F3 c Ed
Send Start/Stop Char.
*No Send Start/Stop Char.
Bs ~CBRCK20. F3 m Ed
Bs ~CBRCK22. F3 } Ed
*No Check Digit
Send Check Digit
Code 39
Bs ~C39ENA1. F3 i Ed
Bs ~C39ENA1. F3 B Ed
Bs ~C39CK20. F3 C Ed
Bs ~C39CK22. F3 S Ed
Bs ~C39ASC0. F3 y Ed
Bs ~C39ASC1. F3 F2 Ed
Send Check Digit
*No Check Digit
* = Default
Interleaved 2 of 5
Bs ~I25ENA1. F3 b Ed
Bs ~I25ENA00. F3 Z Ed
Bs ~I25CK20. F3 < Ed
Bs ~I25CK22. F3 L Ed
*No Check Digit
Send Check Digit
Matrix 2 of 5
Bs ~X25ENA0. F3 x Ed
Bs ~X25ENA1. F3 F3 Ed
Code 93
Bs ~C93APP1. F3 ] Ed
Bs ~C93APP0. F3 U Ed
Code 128
Bs ~128ENA1. F3 > Ed
Bs ~128ENA0. F3 6 Ed
Bs ~GS1ENA1. F3 J Ed
Bs ~GS1ENA0. F3 B Ed
* = Default
Bs ~UPAENA0. F3 . Ed
Bs ~UPAENA1. F3 6 Ed
Note: When UPC-A Off is scanned, UPC-A bar codes are transmitted as EAN-13.
Bs ~UPAAD21. F3 K Ed
Bs ~UPAAD20. F3 C Ed
Bs ~UPAAD51. F3 ` Ed
Bs ~UPAAD50. F3 X Ed
Add 2
*No Add 2
Add 5
*No Add 5
Bs ~UPEEN01. F3 6 Ed
Bs ~UPEEN00. F3 . Ed
Most UPC-E bar codes lead with the 0 number system. To read these codes.
use the UPC-E On selection.
Bs ~UPEAD21. F3 [ Ed
Bs ~UPEAD20. F3 S Ed
Bs ~UPEAD51. F3 p Ed
Bs ~UPEAD50. F3 h Ed
Add 2
*No Add 2
Add 5
*No Add 5
* = Default
Bs ~E13ENA1. F3 O Ed
Bs ~E13ENA0. F3 G Ed
Note: If you want to convert UPC-A bar codes to EAN-13 format, scan the UPC-A Off
bar code on UPC-A On/Off.
Bs ~E13AD21. F3 d Ed
Bs ~E13AD20. F3 \ Ed
Bs ~E13AD51. F3 y Ed
Bs ~E13AD50. F3 q Ed
Add 2
*No Add 2
Add 5
*No Add 5
Bs ~EA8ENA1. F3 , Ed
Bs ~EA8ENA0. F3 $ Ed
Bs ~EA8AD21. F3 A Ed
Bs ~EA8AD20. F3 9 Ed
Bs ~EA8AD51. F3 V Ed
Bs ~EA8AD50. F3 N Ed
*No Add 2
Add 2
Add 5
*No Add 5
* = Default
Bs ~PDFENA1. F3 Bc Ed
Bs ~PDFENA0. F3 { Ed
Bs ~IDMENA0. F3 “ Ed
Bs ~IDMENA1. F3 * Ed
Bs ~AZTENA0. F3 p Ed
Bs ~AZTENA1. F3 x Ed
Micro PDF417
Bs ~MPDENA1. F3 2 Ed
Bs ~MPDENA0. F3 * Ed
QR Code
Bs ~QRCENA1. F3 < Ed
Bs ~QRCENA0. F3 4 Ed
59652 15412
0 269658 4
Code 39
Code 128
Interleaved 2 Of 5 (ITF)
This is PDF417 test bar code
This is Aztec test bar code
Data Matrix
This is Data Matrix test bar code
Visit official site for this manual download
Elite Reader
PN: EDQ320-15 Rev E0.15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF