Muvi X-Drone calibration Page 1: LED Flight Indicators Page 2

Muvi X-Drone calibration Page 1: LED Flight Indicators Page 2
Muvi X-Drone calibration
Page 1: LED Flight Indicators
Page 2: Accelerometer Calibration
Page 4: Gyroscope Calibration
Page 5: Remote Calibration
Please refer to user manual for Compass Calibration
X-Drone Accelerometer Calibration Steps
1. Place the X-Drone on a flat piece of ground. Turn on the remote and then turn on the XDrone.
2. After the X-Drone has turned on normally toggle both joysticks
together, moving them down and inwards as show until the
lights go out on the X-Drone and then return the joysticks to
the middle position. This means that the X-Drone has entered
accelerometer calibration successfully.
3. When the four arm lights on the X-Drone turn on
again, place the X-Drone on the ground upside down.
To avoid scratching the X-Drone we recommend that
place it on a cloth or similar item. Toggle both joysticks
on the remote together, moving them down and
inwards as before until the lights go out on the XDrone and then return the joysticks to the middle
position.
4. When the four arm lights on the X-Drone turn on again,
lean the four arms of the X-Drone against a wall, with the
nose facing downwards, to make it perpendicular to the
ground. Toggle both joysticks on the remote together,
moving them down and inwards as before until the lights
go out on the X-Drone and then return the joysticks to the
middle position.
5. When the four arm lights on the X-Drone turn on again, lean
the four arms of the X-Drone against a wall, with the nose
facing to the left, to make it perpendicular to the ground.
Toggle both joysticks on the remote together, moving them
down and inwards as before until the lights go out on the XDrone and then return the joysticks to the middle position.
6. When the four arm lights on the X-Drone turn on again,
lean the four arms of the X-Drone against a wall, with the
nose facing upwards, to make it perpendicular to the
ground. Toggle both joysticks on the remote together,
moving them down and inwards as before until the lights
go out on the X-Drone and then return the joysticks to the
middle position.
7. When the four arm lights on the X-Drone turn on again, lean
the four arms of the X-Drone against a wall, with the nose
facing to the right, to make it perpendicular to the ground.
Toggle both joysticks on the remote together, moving them
down and inwards as before until the lights go out on the XDrone and then return the joysticks to the middle position.
8. When the four arm lights on the X-Drone turn on again
this means the calibration has been successful. Place
the X-Drone back on the ground the correct way up and
turn the X-Drone and the remote off.
We recommend you calibrate the accelerometer and gyroscope together, one after the other.
X-Drone Gyroscope Calibration Steps
1. Place the X-Drone on a flat piece of ground. Turn on the remote and then turn on the XDrone.
2. After the X-Drone has turned on normally toggle both joysticks together,
moving them up and outwards as show until the rear lights the X-Drone
start flashing slowly and then return the joysticks to the middle position.
This means that the X-Drone has entered gyroscope calibration
successfully.
3. The rear LEDs will flash red for around 15 seconds. If calibrated
successfully, they will turn to a solid red. If the calibration fails, they will
flash red quickly.
4. If the calibration fails, move the drone to a different surface away from vibrations and stand
a few feet away from the drone.
We recommend you calibrate the accelerometer and Gyroscope together, one after the other.
X-Drone Remote Calibration Steps
1. Put switch two (S2) in the down position and then turn on the remote control.
2. The middle LED should be flashing quickly
3. Spin both joysticks 5-10 times in a full circle, touching all 4 corners.
Spin the left joystick ant-clockwise and the right joystick clockwise
as shown.
4. Put switch two (S2) back in the up position, and then turn the
remote off and on to complete calibration.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising