operator manual de luxe 43b– de luxe 50b

operator manual de luxe 43b– de luxe 50b
OPERATOR MANUAL
DE LUXE 43B– DE LUXE 50B
ATTENTION DO NOT USE THE MACHINE WITHOUT READING THE
INSTRUCTION MANUAL.
ING. O. FIORENTINI S.p.A.
INDUSTRIAL CLEANING MACHINES
INTRODUCTION
INTRODUCTION
CONFORMITY DECLARATION
TECHNICAL DESCRIPTION
GENERAL INFORMATION
MANUFACTURER RESPONSABILITY
INTERVENT REQUEST
TRANSPORTATION
HANDLING OF PACKED MACHINE
UNPACKING THE MACHINE
HANDLING OF UNPACKED MACHINE
OPERATORING CONTROLS
DASHBOARD CONTROLS
DASHBOARD SYMBOLS
USE OF THE MACHINE
CHOOSING THE DETERGENT SOLUTION
SCRUBBING
WATER FILLING AND DISCHARGE, TANK CLEANING
SQUEEGEE ADJUSTMENT
BRUSHES REPLACEMENT
SAFETY, MAINTENACE AND INSPECTIONS
GENERAL SAFETY RULES
MAINTENANCE SCHEDULE
SQUEEGEE BLADES REPLACEMENT
VACUUM MOTOR MAINTENANCE
CONTROLS
SAFETY CONTROLS INSPECTION
ELECTRIC INSTALLATION INSPECTION
2
3
4
5
6
6
6
7
7
7
7
8
8
8
9
9
9
10
10
11
11
11
14
14
15
16
16
16
INTRODUCTION
AS SOON AS THE MACHINE ARRIVES PLEASE CHECK THAT
EVERYTHING IS OK,PLEASE CHECK THAT THERE IS NOT ANY DAMAGE
DUE TO TRANSPORT AND CHECK TO HAVE RECEIVED ALL THE
SHOWING ON THE DOCUMENTS.
IN CASE OF DAMAGES OR MISSING PART PLEASE ADVISE
IMMEDIATELY THE MANUFACTURER
INTRODUCTION
THIS KIND OF SCRUBBER MACHINE ALLOWS THE OPERATOR TO
CLEAN ALL KIND OF FLOOR AND ALL KIND OF DIRTY ,GIVING THE
BEST RESULT.
YOU CAN REACH BEST PERFORMANCES USING THE MACHINE IN A
PROPER WAYAND TAKING CARE OF IT.
PLEASE READ THIS MANUAL WITH ATTENTION.
USE THE MACHINE ONLY FOR CLEANING PURPOSE.
Keep this manual for all needs.
GOODS TO BE RETURNED
In case of goods to be returned for warranty replacement, it is necessary to have a written
acceptance from
FIORENTINI technical department before sending them.
All defective parts must be carefully packed in order to avoid further damages during transport.
Goods must be shipped ex-warehouse and followed by :



serial number of the equipment where they were installed on;
item code of the defective part;
detailed description of the defect and of the condictions where it happened.
In case of defective electric or electronic goods,
please return them separately from other materials,
in order to help us in dividing dangerous wastegoods
and recicle the (RAEE) as DER 2002/96/CEE LOW.
CONFORMITY DECLARATION
Conformity declaration is consigned with the support and the manual of operating and maintenance
instructions.
3
4
TECNICAL DESCRIPTION
DIMENSIONAL CHARACTERISTICS
LENGHT
WIDTH BRUSH COVER
HEIGHT
N° BRUSHES
BRUSH SIZE
PRESSURE BRUSH
WORK WIDTH
SQUEEGEE WIDTH
SOLUTION TANK IN POLYETHYLENE
RECOVERY TANK IN POLYETHYLENE
FRONT WHEEL DIAMETER
REAR WHEEL DIAMETER
TRACTION
WEIGHT WITHOUT OPERATOR
WEIGHT WITHOUT BATTERY
BATTERY COMPARTMENT SIZE (l x w x h)
ELECTRIC CHARACTERISTICS
VOLTAGE
BRUSH GEARMOTOR
TRACTION MOTOR
VACUUM MOTOR
FUNCTIONAL CHARACTERISTICS
BRUSH LIFT CONTROL
SQUEEGEE LIFT CONTROL
PERFORMANCES
FORWARD RUNNING SPEED
MAX.SLOP
HOUR SCRUBBING m²/h
ECOLOGIC CHARACTERISTICS
NOISE AT DRIVER’S EAR
5
DE LUXE 43B
DE LUXE 50B
1000 mm
480 mm
1060 mm
1
430 mm
30Kg
430 mm
700 mm
45 liters
45 liters
160 mm
80 mm
Electric
135 Kg
80Kg
310x350x260
1030 mm
550 mm
500 mm
500 mm
140 Kg
85Kg
24 V
370W 17A
110W 8A
550W 22A
By pedal
By pedal
0÷3,5km/h
3%
1500mq/h
72 decibel
1750mq/h
GENERAL INFORMATION
MANUFACTURER RESPONSABILITY
The manufacturer ING.O.FIORENTINI SRL is not responsible for any inconvenient, failures,
accidents, etc.due to the non-acquaintance (or non-fulfilment) of the prescriptions contained in this
manual .The same applies to change’s execution, modifications, and/or to the installation of
accessory not preliminarily authorized.
In particular the firm ING FIORENTINI SRL is not responsible for any damages caused by:
o Natural calamity
o Erroneous operations
o No maintenance
Furthermore ,the MANUFACTURER is not responsible for any interventions not performed by
authorized personnel.
INTERVENTION REQUEST
Possible intervention requests should be made after an accurate analysis of the inconvenient and
their causes .In any case, when calling the technician, report what follow:
o Model of the machine
o Serial number (fig. 1)
o The detail of the faults
o Inspections done
o Any other information considered useful for this purpose
o Address the requests to authorised customer service.
Fig. 1
Ing. O. Fiorentini
S.r.l. Piancaldoli (FI)
Mod.
S.N.
Hz.
V 24
A 47
Kg 135
6
MADE IN
ITALY
CE
2002
W 1020
TRANSPORTATION
HANDLING OF PACKED MACHINE
The machine is supplied packed on pallet, closet in a box made of plywood or paper board. The
weight and sizes are showed in the normal characteristics.
The barycentre position is indicated by black arrow on the box. The forks of the lift truck or the
transpallet should be placed so that the black arrow indicated on the packing is about in the centre
of the forks. The package should be handled with extreme caution, this avoiding impacts or lifting it
to remarkable heights without any reasons. It is forbidden to stack the packages one another.
Fig. 2
UNPACKING THE MACHINE
1. Cut the straps with proper cutting nippers
2. Remove the clips on the paper board to the pallet
3. In case of package made of plywood ,remove the clips on the sides and on the base of each
panel as well
4. Remove the other clips fastening the machine by cutting them in the same way of external
ones
5. Brought the machine at round level
HANDLING OF UNPACKED MACHINE
1.
2.
Check the machine
If the machine must handled for a short transport after being used, and remove the brushes
and the squeegee. For longer transport, is recommended to pack the machine again in its
original box
7
OPERATING CONTROLS
DASHBOARD CONTROLS
1
MAIN KEY SWITCH
2
VACUUM MOTOR SWITCH
3
BRUSHES MOTOR SWITCH
4
BATTERY CHARGER INDICATOR
5
SAFETY MOTOR
DASHBOARD SYMBOLS
0
Close (off)
1
On (first function)
Key Switch
Scrubbing Brush
Vacuum by Squeegee
Traction safety motor
Indicatore di carica batteria
8
USE OF THE MACHINE
BATTERIES INSTALLATION
o Lift up the recovery tank in order to access to batteries box
o Install the batteries as per picture fig. 6-b
o Never add distilled water after recharging the batteries
o Clean the surfaces that are in contact with the connections
Fig. 3
BATTERY CHARGER INSTALLATION
o Install the battery charter in a ventilated and dry place, far from heat sources and corrosive
environments.
o Make sure that the voltages are correct. Protect the mains with a delayed switch or with a load
fuse higher than the max. power consumption of the battery charter .Observe the polarity of the
battery socket(black and red cables are identified by symbols +,-
CHOOSING THE DETERGENT SOLUTION
For a good cleaning of the floor, it is important to choose the proper detergent solution. If
necessary, ask the supplier or a competent person for the proper solution. Keep in mind that a too
strong chemical agent can compromise the long life of each machine. It is necessary to use a lowsudsing detergent solution, or an antifoaming additive, in order not to damage the vacuum motor. If
it is impossible to get these products, use some vinegar to avoid foam, pouring 50cc of it in the
recovery tank before scrubbing.
SCRUBBING
The scrubbing operation is very delicate, as the operator’s experience must be used to decide upon
the brush type, the requirement of a possible double scrubbing operation, the right cleanser choice
and the right machine adjustments: if only one of these factors is inadequate, the scrubbing
operation can give very poor results. If the floor is very dirty or difficult to be cleaned, a double
scrubbing operation is recommended. In this first phase, the squeegee must be lifted and the brushes
must be in working position. Start the brushes and pass the machine over a surface of some tenth sq.
mt. Let the detergent solution on the floor to dissolve the dirt, then pass the machine again. For this
second machine passage, lower the brushes and bring the squeegee in contact with the floor.
Look at the floor after this second passage and decide if the scrubbing operation was enough or if an
additional operation is required. To perform the scrubbing procedure, turn the brush motor ignition
9
switch to pos. 1, brushes motor start. The brushes will be lowered to the floor pushing on the brush
plate lowering block. Now operate immediately the lever to apply the detergent water, and adjust it
accordingly. Put the run selector (fig.2) in its forward position and press the pedal (fig.3) so that the
machine moves forward and starts scrubbing. The water dosage must be adjusted to get the whole
surface completely wet after the brush passage, but without any excess, that could generate
splashes, stream or flows out of the squeegee. If no double scrubbing is not performed, lower the
squeegee after placing the run switch in forward position. The squeegee is lowered by means of the
pedal. The vacuum motors are operated by means of the switch. Once the scrubbing and drying
procedure are finished, first of all close the water with the lever , then lift the brushes by means of
the pedal and the squeegee by means of the pedal. Finally, turn the motors off.
WATER FILLING AND DISCHARGE, TANK CLEANING
Before every scrubbing operation, open the door and fill the solution tank with the right quantity of
water and cleanser. The tank is made of polyethylene resistant to all acid and basic solution and to
all dissolvents found on the market. At the end of the scrubbing operation, discharge the dirty water
from the tank by means of the hose. Accurately clean the tank at least once per week.
SQUEEGEE ADJUSTMENT
The squeegee must be perfectly adjusted to get a perfect floor drying ( fig. 8).
The main characteristic of this type of squeegee is to pick-up the water from the floor and convey to
the vacuum hose, but it must be parallel to the floor. To rightly adjust the squeegee operate as
follow:
Extract the key from the control dashboard to avoid accidental start of the machine.
o To adjust the squeegee slope operate the knob (fig 3).
o The right pressure is got when the edge of the rear blade touches the floor with a slating of
approx. 60°-45° referring to the floor.
1.
2.
3.
4.
5.
6.
7.
handle position adjustment knob
solution adjustment lever
battery charge plug
squeegee lifting lever
brush lifting pedal
squeegee slating adjusting knob
parking brake lever
Fig. 3
Note that often drying is negatively affected by a wrong suction operation. If the suction hose
doesn’t work well, drying will continue to be bad, even with all adjustments attempts. In this case:
a- accurately clean the suction hoses, their inlets and filters and the squeegee itself.
b- check the vacuum motors operation.
c- confirm that all inspection openings of the tank are closed.
10
BRUSHES REPLACEMENT
How to attach the brush in order to fix the brush is necessary:
o Place the machine on the brush, keeping the brush plate up
o Switch on the brush and lift down the brush plate and allows the brush to be fixed
o In order to replace the brush is necessary to lift up the brush switch off the brush switch, the brush automatically
goes away.
N.B.
It is not necessary to move the brush cover to do all those operations.
Fig. 4
Fig. 5
SAFETY, MAINTENANCE AND INSPECTION
GENERAL SAFETY RULES
Before using the machine ,instruct all operators to read carefully the charter ”SAFETY
STANDARDS “WARNING.
o The manufacturer can make any changes to the machine, for constructive or commercial
reasons, without being obliged to change the instruction manual at the right time according to
these modifications.
o The person responsible for the machine must adhere to CEE rules and to the local standards as
well, regarding the working environment for operator’s safety and health purposes.
o Before starting the machine ,always perform the preliminarily checks. The safety standards
which involve any dangers, mentioned in the manual text, can be recognized by the symbol:
CAUTION.
o Beyond the standard listed hereunder, the person responsible for the machine must comply with
the rules provided by the law in force regarding personnel’s safety and health in the working
stations. Furthermore, the person responsible for the machine must instruct the operators on
what follows:
o Safety and accident prevention standards
o Specific standards regarding the machines
o Location on the machine of emergency pushbuttons or similar mechanism, for a prompt
operation. The fixed or movable protections(carters)should always remain in their
position, correctly fixed with perfect integrity during all procedures regarding the
normal operation. If, for any reason ,the carters are removed, their efficiency should be
restored before restarting the machine.
11
o Use the machine only under technically unexceptionable conditions and in compliance
with its destination, by observing the safety and prevention standards according to the
prescriptions contained in the instruction and maintenance handbook.
o Remove (or let remove) immediately any failures which could compromise the safety.
o The machine is designated to be used as a scrubber ;any other different use doesn’t not
comply with its destination. the manufacturer/supplier takes no responsibility for any
consequent damage.
o DANGER
It is absolutely forbidden to suck inflammable and or toxic liquids and powders
o DANGER
It is dangerous and absolutely forbidden to touch the lower part of the machine with the hands
when some parts are moving. Should it be absolutely necessary, remove the main key from the
control dashboard.
CAUTION
Keep in mind the following standards; failure to adhere to these rules can endanger the life of the
operator or of other people. Always keep a sufficient distance from the sidewalk edges and from
large differences in height of the floor where the machine can fall; never adopt a work technique
that can compromise the stability of the machine. Never pass through slopes in transversal
direction; when going through a downhill road, always adjust the speed to the environment
conditions. Do not turn the machine at excessive speeds, particularly if the floor is not flat.
CAUTION: DANGER
Never operate the machine when stopped for special operations (setting up, maintenance, etc.).
Before starting the work, check for any possible visible defects on the safety devices, and the
correct operation of the emergency stop pushbutton or of the equivalent mechanism . Never operate
the machine when the control panel indicates defective tools, warning lights, etc.
MAKE SURE THAT:
- No strangers are present near the machine
- No strange objects (appliances, cloths, etc.) are on the machine
- The machine does not emit strange noises after its starting; if so, stop it immediately and detect the
cause.
All doors and protections are regularly closed.
Never let approach strangers near the machine. Use, maintenance and repair of the machine are
allowed only to operators authorized by the person responsible of the machine, who knows the
manual contents. These operators should be persons physically and intellectually fit for this work,
not under alcohol or drug effects.
MAINTENANCE INSTRUCTIONS
During the scrubbing operation, the maintenance of the machine and the replacement of parts, it is
necessary to extract the ignition key.
Instructions for battery:
- when charging the battery, let the battery cover open
- do not use free flames and do not smoke near batteries
- caution: liquid is corrosive
- do not cause sparks near the batteries
- battery gases are explosive
- do not cause any short-circuits
- do not invert polarities
GENERAL NOTE
For any maintenance, revision or repair, engage qualified personnel or call an authorized workshop.
Use only original fuses with the prescribed current intensity. In case of a power failure, disconnect
12
the machine or the plant immediately. The electric installation should be periodically inspected and
checked. Any possible failure, such as detached connections and burnt cables should be
immediately removed.
CAUTION
To clean the machine, use aggressive detergent solutions, acids, etc. only when necessary and
with special care. Adhere to all instructions of the detergent manufacturer. Use protective clothes
(overalls, gloves, protective glasses, etc., see CEE standards).
OPERATIONS ON THE ELECTRIC INSTALLATION
The operations on the electric installation can be performed only by QUALIFIED
ELECTRICIANS, instructed in the electric characteristics of the machine and in accident
prevention rules.
CHECKS
The machine must be inspected by a technician, who checks the safety conditions of the machine
and any possible damages or defects visible from outside:
- before setting the machine at work
- after appropriate time intervals
- after any changes or repairs
- safety device control
SAFETY DEVICE CONTROL
All six month, check the efficiency of the safety devices, the inspection should be performed by
qualified personnel of FIORENTINI s.r.l. or authorized by it. To grant the efficiency of the safety
devices, the machine should be overhauled by a technician of FIORENTINI every 5 months.
ANNUAL CHECK
The responsible person should perform an annual check to determine if the machine complies with
the technical safety standards. After this check, the responsible person should apply a test plate on
the machine.
INFORMATION FOR USING THE MACHINE IN EXPLOSIVE ATMOSPHERE
The machine has not been designed to work in environments in which explosive gas, powders or
steams can be generated.
DANGER
To drain the liquids used for floor scrubbing, follow the local standards concerning the elimination
and purification.
INFORMATION CONCERNING THE MACHINE DEMOLITION<R>(CEE STANDARDS)
In case of machine demolition, it is important to subdivide the different types of materials
composing the machine and deliver the batteries to operators authorized to their elimination.
BATTERY TECHNICAL CHARACTERISTICS
TENSION
V 12
CAPACITY
100 A/h
WEIGHT
30 Kg
SIZE (H.x W x.L)
29x17x22.5
BATTERY CAHRGER TECHNICAL CHARACTERISTICS
IN
OUT
V 230, Hz 50, A5
V 24, A 12
This kind of battery charter can charge all brand name of batteries.
13
MAINTENANCE SCHEDULE
During the cleaning and the maintenance of the machine remove the key.
DAILY
o Clean the recovery tank and the filter of the vacuum motors.
WEEKLY
o Check for the cleaning of the suction pipes and of the squeegee
o Check the state of the rubber squeegee blades
MONTHLY
o Check the filter of the clean water tank
EACH YEAR
o Check the brush state of each motor
AFTER TWO YEARS
o Check safety systems
Check electric installation
SQUEEGEE BLADE REPLACEMENTS
The squeegee blades should be replaced when the contact edge becomes worn; the perfection of the
edge is essential for a perfect drying. To replace the blades
o The squeegee should be demounted from the machine and placed on the desk.
o Now, remove the screws (fig) both on the front part and on the rear part of the squeegee, the
steel straps and remove worn rubber blades
o Perform the inverse procedure and assemble the new blades, then adjust the squeegee.
Fig. 6
1.
2.
3.
4.
5.
14
squeegee front blade
squeegee body
squeegee rear blade
squeegeecounterblade
squeegee straps
VACUUM MOTOR MAINTENANCE
The vacuum motors must be checked and cleaned. The brushes should be checked all six months
and replaced, if necessary. After removing the key from the dashboard, unscrew the screw in the
vacuum motor space, open it, unhook the hooks and detach the plug . In this way, it is possible to
extract the motors and release the sponge filter under the motors that can be extracted, cleaned and
replaced. Check the suction fan from the hole located in the front part of the vacuum motor. By a
visual check, the fan should appear undamaged and well-cleaned. To check the brushes, first of all
remove the plastic cap, then unscrew the screws and remove the two plastic supports of the
brushes. Once checked and replaced (if necessary), the brushes can be easily remounted, by
reassembling all elements until the initial situation has been reached.
1.
2.
3.
plastic cap
carbon brushes
carbon brushes screws
Fig. 6
CAUTION
Each maintenance and repair operation not described under the “ordinary maintenance”
should be performed by qualified personnel authorized by FIORENTINI S.p.A only.
15
CONTROLS
The scrubber must be inspects from a technician that controls its safety conditions and the presence
of possible damages or visible defects to the outside.
o To the first operation
o After changes and reparations
Check to the safety devices
Every 2 years to check the efficiency of the safety devices, the inspection must be performs at a
professional technician. To guarantee the general efficiency every 5 years the scrubber must be
revises from the personnel of the Fiorentini company.
Check on the electric installation
The preparation of the electric plant has to be every 2 years inspected and examined. Possible
defects as disconnected connections or damaged cables, must immediately be eliminated The
interventions must be perform only at a professional technician.
16
Mat. n.
Serial no.
Nr. de serie
_____________________
Data di spedizione
Date of shipment
Date de spedition
_____________________
Distributed by:
ING. O. FIORENTINI S.p.A.
“THE BEST IN FLOOR MACHINES”
FILIALI:
20132 MILANO – Fax. 02/2592779
Via Palmanova 211/a – Tel. 02/27207783 - 2564810
00012 Guidonia Montecelio (ROMA) – Fax. (0774)353419 - 353314
Via B. Pontecorvo 20 – Tel. (0774)357184 - 353015
STABILIMENTO:
50030 PIANCALDOLI (FI) – Fax. 055/817144
Loc. Rombola – Tel. 055/8173610
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising