LCD Manual Revised

LCD Manual Revised
NEXANGE LCD MANUAL
ON/OFF & SCREEN LIGHT
SET
UP
DOWN
NEXANGE -LCD SICONS (1)
4. Current
speed and
wheel size
1.
Battery
capacity
2.Assistance
level
3.Wheel
diameter
5. Cycle show,
total distance,
single cycling
time, single
cycling
distance and
the top speed
ON/OFF (2)
Turn on the system by pressing O button more than 2 seconds.
BATTERY CAPACITY (3)
BATTERY
CAPACITY
80-100%
CAPACITY
60 - 80%
CAPACITY
40 - 60%
CAPACITY
20 - 40%
CAPACITY
10 - 20%
CAPACITY
0 - 10%
CAPACITY
SCREEN LIGHT (4)
Press O button to turn on the screen light. Press again to turn it off.
CHANGE ASSISTANCE LEVEL (5)
Press the UP or DOWN button, it can change assistance lever. There are 7
levels, from zero to six.
6KM/H STATE (6)
Press the UP button more than 2 seconds, it will get into the 6KM/H state.
24 V OR 36V STANDARD VOLTAGE SELECTION (7)
Press both the UP and DOWN button at the same time for more than 10 seconds , the
screen will show the voltage options, then press UP or DOWN button to choose 24V
or 36V.
KM/H OR MPH (8)
Press both SET and DOWN button at the same time for more than 10
seconds , the screen will show indicator options of SPEED and WHEEL
SIZE , then press UP or DOWN button to choose KM/H or MPH
CHANGE SETTING MODE(9)
Press SET button, the present mode will blink which means you may operate. Then press the UP
or DOWN button to switch among total distance, single cycling time, single cycling distance, the
top speed and cycle show. It will back to electric state if you don’t operate on it within 10 seconds
or after 5 seconds when you end up the operation.
PUSH
ING
DOW
N
BUTT
ON
PUSH
ING
UP
BUT
TON
CYCLE SHOW MODE (10)
Under bicycle state model, press the UP or DOWN button, when choose cycle show
symbol, LCD will take 5s as a unit, showing single cycling time, single cycling distance,
the top speed and the total distance
CYCLE
SHOW
SYMBOL
ZERO CLEARING (11)
Under free setting mode, press the DOWN button for 5 seconds, it
clears single cycling distance, single cycling time and the maximum
speed to zero (the whole distance can not be cleared to zero)
SET WHEEL SIZE (12)
Press SET button for 10 seconds, it will get into wheel size setting mode. Press
UP or DOWN button to choose the figure that is similar to wheel girth. It will be
setted after 5 seconds without operation.
RIM SIZE
CIRCUMF
ERENCE
SET WHEEL SIZE (13)
Rotate the wheel on the ground and measure the distance.
SET WHEEL SIZE(14)
16×1.75×2
47-305
1272
27×1
1/4
32-630
2199
20×1.75×2
47-406
1590
27×1
1/4
28-630
2174
37-504
1948
28×1.5
40-622
2224
24×1.75×2
47-507
1907
28×1.75
47-622
2268
26×1
23-571
1973
28×1
1/2
40-635
2265
26×1.5
40-559
2026
28×1
3/8×1
37-622
2205
26×1.6
44-559
2051
700×18C
18-622
2102
26×1.75×2
47-559
2072
700×20C
20-622
2114
26×1.9
50-559
2089
700×23C
23-622
2133
26×2.00
54-559
2114
700×25C
25-622
2146
26×2.125
57-559
2133
700×28C
28-622
2149
26×1
3/8
37-590
2105
700×32C
32-622
2174
26×1
3/8×1
37-584
2086
700×35C
35-622
2205
20-571
1954
700×40C
40-622
2224
24×1
3/8
26×3/4
A
1/2
Fifty
5/8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising