SDC-5330 / 5340 Programmable DC

SDC-5330 / 5340 Programmable DC
SDC-5330 / 5340
Programmable DC-DC Converter with Battery Charger function
USER'S MANUAL
1.
INTRODUCTION
This MCU controlled Step Down DC-DC Converter has a digitally adjustable output in 0.2V increments.
It can also be set up as a Two Stage Battery Charger.
Output voltage and current is displayed in the LED in turn or selectively as desired.
8 fault codes can be shown in LED for different fault diagnosis.
Intended Applications
*
*
*
Ideal for voltage sensitive loads, devices and equipment near or far from DC source.
Remote Automatic or Manual On/ Off Control of output makes it ideal for various DC power and DC
management applications.
Suitable for on-board charging of stand alone 12V Battery Bank or Battery with load.
2.
FEATURES
1.
8.
9.
Digitally adjustable 0.2 V step of output voltage (12V-15V DC) makes it ideal
for voltage sensitive devices.
2 stage Battery Charger mode with 14.3V Bulk and 13.6V Float charge.
3 digit LED display for Voltage, Current, Operation Mode and Protection/ Fault Diagnosis.
Remote Control Terminal for Manual or Automatic on /off of output voltage.
Remote Voltage Sensing for optimal and accurate powering of distant load or charging battery.
Remote alarm terminal (13.5V, 0.25A) for powering external warning device when input is under19V.
A separate always-on auxiliary output (13.8V, 0.5A) to power critical electronic devices such as security
device or remote On Off manual switch.
fail-save protection, with 7 self-recoverable and all with fault code on LED Display.
Thermostatic control cooling fan.
3.
CAUTION
1.
When an inductive load such as motor, solenoid is used, a diode (400V, 3Amp) must be installed across
the load as shown in (Connection Diagram 1) to protect the converter from the high voltage spike
generated by the load when the supplied current is switched OFF.
When the fuse is blown, find out and fix the problem and replace the fuse with the same type and rating.
Avoid touching the heat sink during operation as it may burn your hand.
2.
3.
4.
5.
6.
7.
2.
3.
4.
PANEL VIEW
1.
2.
3.
4.
3 digit LED. Displays voltage, current, operation and fault code.
LED indicates Voltage (V) and Current (A).
Battery Icon is on when converter is set at the charger mode.
Set button.
5.
INPUT, OUTPUT, CONTROL & AUXILARY TERMINALS VIEW
Remote
13.8V 0.5A
GND
NC
Alarm
S+ S-
Remote Terminal for Automatic / Manual control of Output On-Off
Always On Auxiliary Output
Ground terminal
No connection, a dummy terminal
Alarm for low input voltage by DC +13.5V and 0.25A to power warning device (LED)
Voltage Remote Sensing positive and negative terminals,
6.
Wiring Diagram
6.1 Connection Diagram 1
Example 1
Example 2
Example 3
6.2 Connection Diagram 2 (Negative Ground)
7.
INITIAL SET UP AND CONNECTION
1.
2.
Leave the output terminals disconnected.
Connect a 24V battery to input terminals.
DOUBLE CHECK FOR CORRECT POLARITY BEFORE CONNECTION.
3.
4.
5.
.
Programming Procedure using the SET button
Press and hold the “SET” button until shows up and display flashes.
Flashing digits indicate unit is in programmable mode.
Otherwise repeat step 4 to get to programmable mode again.
Each short press will increase the output voltage setting by 0.2V step..-> 15.0V -> CHA (Charger Mode).
And then back to 12.0V as shown in the following cycle chart.
6.
6.
7.
8.
if you select to set to battery charger mode.
Stop at the desired Output Voltage or at the
After a few seconds, the display stops flashing to confirm the selected new setting confirmed and the
unit will operate in the new set output voltage or as a battery charger.
Now you can connect the output terminal to a 12V device or a 12V battery according to your set mode.
Always double check for correct polarity.
8.
REMOTE TERMINAL FOR AUTOMATIC / MANUAL OUTPUT On-Off CONTROL
1.
2.
The converter is set to Output always on by default at the factory.
Application of the Remote Control Terminal:
A.
The converter can be set to manual control of Output On-Off via external toggle switch
B.
The converter can be set to automatic control of Output On-off via the Ignition Switch DC source.
C.
3.
The remote on off function can be controlled via many types of on-off switches with various DC
source of positive 8V-32V.
Once the Remote Terminal has been connected to a positive 8-32V, the converter will be modified to
Remote Control Mode and will remain in this Remote Control Mode until it is disabled either by reset
, or to factory preset
see section 11 and 12 for more detail information.
9.
GENERAL OPERATION
LED Display
During operation, the LED display shows voltage and amps in turn.
Quick press of the button will either freeze the display (at desired V, A) or return to the default scrolling mode.
The display will switch off after 5 minutes to conserve energy. It can be restarted again by a quick press of
the button.
When the output current is less than 1 Amp or output is open circuited the LED display will show
indicating Low Output Amp. This applies to both converter and charger mode.
In the charger mode when the output float voltage is 13.6V and the current to the battery is less than 1 Amp,
can be interpreted that the Battery is Full. In the converter mode means that there is less than 1 Amp or no
load drawing from the output or that the output is open circuit.
Remote Voltage Sensing
Voltage converter it can be finely tuned to supply your device the required voltage even when your device is
at a distance, you can use the remote voltage sensing terminal (S-, S+) to ensure accurate point of load
voltage to further improves the stability of the load point voltage.
Alarm Terminal
Alarm terminal is for input low voltage alert (F05) which provides 13.5V, 0.25A to remote LED to give out alert
before the converter enters into low voltage protection mode and shuts down. The alarm signal will be On
once the input is below 21V and will be Off when the input rises back above 25V.
10. BATTERY CHARGER MODE - TWO STAGE CHARGER
When the unit is set at the Charger Mode, LED Display
confirm the Charger Mode in operation.
, the charger icon
will be lit up to
The Bulk Charge with constant current max set at 30A/40A and max voltage to 14.3V and the Float Charge
voltage is at 13.6V.
The Charger Icon flashes in Bulk Charge and becomes constant in Float Charge.
Quick press to Set Button will display charging voltage and current.
Please note that when the battery is full and the float charge current is less than 1A, the current display
shows
11. DISPLAY INDICATION
Low Current Display when the output current is less than 1 Amp
CHARGER Mode
SELECTION (programmable) Mode, ready for programming of output voltage &
charger mode
REMOTE CONTROL DISABLED, there is always output when input is powered up
FACTORY DEFAULT SETTINGS ENABLED (see section 12 for default settings)
Flashing = Bulk Charge, Solid = Float Charge
12. TO ACTIVATE AND DEACTIVATE REMOTE CONTROL MODE
The Remote control terminal is disabled by default at the factory and output is always on.
To enable Remote control mode, just apply a positive 8 to 32Vdc l to Remote terminal.
After remote control mode has been enabled once, it will stay enabled until it is disabled or reset to factory
default setting in 12.
To disable remote control mode
-
is shown.
Press and hold “SET” button until
Release button then wait for few seconds. The remote control will be disabled & output becomes always
ON.
13. FACTORY DEFAULT SETTINGS
1.
2.
Unit is in DC-DC Converter Mode with Output Voltage set at 13.6V
Remote Control is disabled and the Output is always ON.
You can reset converter to factory default setting by following steps.
-
is shown.
Press and hold “SET” button until
Release button then wait for few seconds. The converter is reset back to factory default setting.
14. DISPLAY ON/OFF
The display will be switched off automatically after 5 minutes. Press the Set Button to restart the display for
another 5 minutes.
15. ALWAYS ON AUXILIARY OUTPUT
The DC-DC converter will provide constant 13.8V, 0.5A to power critical devices such as security, alarm and
also a positive voltage source for manual remote on off control of the output .
Upon connection of input to 24V battery supply, the 13.8V terminal will be powered.
16. REMOTE VOLTAGE SENSING PORTS
The remote voltage sensing works for both converter mode and charger mode. It compensates for voltage
drop at distant load or auxiliary battery.
It further enhances the accuracy of output voltage to the distant load or battery and provides more stability
with varying output current.
Just connect AWG 22 cable between the Positive S+ to Positive of load / battery and Negative S- to Negative
of load/ battery.
17. ALARM -- The low input voltage pre-warning
The alarm signal port provides a 13.5V 0.25A for external LED or other alarm device to give pre-warning
signal when input voltage drops below 21V before further dropping to 19V at which output shuts down.
18. LOW CURRENT DISPLAY
when the output current is less than 1Amp.
The display will show
The converter can be in converter or charger mode or when the output is open circuit.
When in charger mode, it means the battery is full.
19. Troubleshooting
If no display comes up after connection to the input, check for correct input polarity.
Disconnect all cables to the unit and check the input fuse.
The LED will display error code when the converter is in any protection mode.
The following table denotes the 8 Error Codes.
Error Code
Description
F01
Over Temperature Protection (Self-restart)
When unit’s internal temperature becomes higher than the threshold value, unit shuts down
output. Unit will resume normal operation automatically once the temperature becomes normal.
F02
Output Over Voltage Protection (Self-restart)
In DC-DC Converter Mode, output shuts down when the output voltage is 15% higher than the
preset voltage level. Unit will self-restart when the output voltage falls 1V below the preset
level.
In the Bulk Charge Stage of Charger Mode, the unit shuts down >16V and restarts when the
voltage <15.5V.
In Float Charge Stage it shuts down when voltage >15.1V and restarts at < 14.6V.
F03
Over Load Protection (Self-restart)
When the Output current is 3 Amp higher than 40A for model SDC-5340, 30A for model SDC5330, the unit will shut down the output. The unit will self-restart once the output current falls
back to unit’s rated value.
F04
Fan Fault (Self-restart)
When the fan does not operate normally, the unit will shut down the output. Unit will resume
normal operation once the fan fault condition has been removed.
F05
F06
Input Low Voltage Protection (Self-restart)
Input V < 21V
Alarm signal On
Input V > 25V
Alarm signal Off
15V < Input V < 19V for 3 min.
Output shuts down ; self-restart > 25V
Input V < 15V
Output instant shut down; self-restart >25V
Output Short Circuit Protection (Self-restart)
Unit shuts down output when the output is short circuited.
It will self-restart when the fault condition is removed.
F07
Output battery terminal reverse polarity protection
Fuse will be blown when the output is reverse polarity connected to the battery.
Replace the fuse with correct type and rating.
F08
Input over voltage protection (Self-restart)
Output shuts down when the input voltage is higher than 33.5V.
It will self-restart when the input drops below 32V.
20. SPECIFICATIONS
Models
SDC-5330
Input Voltage Range
19 – 33VDC
Output Voltage Range
12 – 15VDC (0.2V increments)
Continuous Output Current
30A
No load current
< 50mA
Efficiency
≥ 90%
Protections
Over Voltage, Overload, Input Reverse Polarity, Over Temperature,
Output Reverse Polarity, Output Short Circuit, Input Under Voltage
Aux. Output (Always On)
13.8V / 0.5A
Two Stage Battery Charger
Bulk Charge 14.3V Max.Constant Current 30/40A, Float Charge 13.6V
Remote Control of Output ON/OFF Yes
Remote Voltage Sense
SDC-5340
40A
Automatic or Manual Control
Yes
External Alarm Output 13.5V,0.25A To power warning device when Input under voltage before shut down
Indicators
3 digits LED display for V, A & Error code, Battery Charger Indicator
Cooling System
Thermostatic Control Fan
Operating Temperature
-10°C to +50°C
Approvals
EN 55014, EN60335.2.29
Accessory
Supplied 4 cable lug connectors, One 400V 3A diode
Dimensions (WxHxD)
130x55x160 mm
5.2x2.2x6.3 inch
130x55x190 mm
5.2x2.2x7.5 inch
Weight
1kg
1.2kg
Recommended Battery Capacity
Range
100AH to 300AH
2.2lbs
2.64lbs
130AH to 400AH
REV.0 20160427
7673-5340-0580
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising