IVI6000 - Sittelle Technologies

IVI6000 - Sittelle Technologies
159 – 202 Ave., St-Hippolyte, QC, J8A 1V8
INTERCOM INTERFACE Model IVI6000 Installation Manual
This Confidential Information is to be considered confidential and proprietary to SITTELLE TECHNOLOGIES INC. and Recipient shall hold the same in
confidence, shall not use the Confidential Information other than for the purposes of its business with SITTELLE TECHNOLOGIES INC., and shall disclose it
only to its officers, directors, or employees with a specific need to know. Recipient will not disclose, publish or otherwise reveal any of the Confidential
Information received from SITTELLE TECHNOLOGIES INC. to any other party whatsoever except with the specific prior written authorization of SITTELLE
TECHNOLOGIES INC.
Copyright 2007 Sittelle Technologies Inc., All Rights Reserved
1.0 Equipment Description and Operation
The Intercom VoIP Interface is a 2 x 1 switch. The Intercom VoIP Interface switches the subscriber port from the
Intercom/Telco port to the VOIP port.
Telco /
Intercom
Port
Line
Monitoring
Subscriber Port
Isolator
MTA Port
Line
Interface
Figure 1 – Block Diagram
The unit may be installed with or without telephone service on the Telco/Intercom port. The MTA port powers the unit. If battery is
removed from the default MTA port, the unit will switch to the Intercom/Telco port in less than 30 Seconds. The unit will operate with or
without telephone service connected to the Intercom system. This module, self-powered from the MTA Port, is totally self-sufficient
and needs no external supply.
Power-up
At power up the subscriber may be connected to either the Intercom or VOIP Ports. The unit reset will force the unit to connect the
subscriber to the Intercom port. The reset must be activated while the subscriber port is on-hook. A ring on the MTA port is
required to default the unit to the MTA Port.
General
The unit is compatible with 14 to 48 volts battery intercom systems. After the first ring on the MTA port, the unit will operate as described
below.
Subscriber on-hook
While the subscriber port is on-hook, a ringing signal on the Intercom port will cause the unit to switch automatically to the Intercom port.
Subscriber off-hook
While the subscriber port is off-hook, a ringing signal on the Intercom port will cause the unit to generate a series of tones to indicate that
the Intercom port is ringing. During and after the tones, the subscriber can use the # key on the telephone to answer
the Intercom use double # with cordless phones . The MTA port is placed in the hold condition and the subscriber is switched
to the Intercom port.
Switch back
If the subscriber answers the call, after the intercom disconnects the IVI6000 will switch back automatically to the MTA. An on-hook
condition will also cause the unit to switch back to the MTA port for example if the call is not answered. If battery is removed from the
Intercom port, the unit will switch back to the MTA port. If a hold was in effect, it will be removed. The IVI6000 will automatically time out
after 20 seconds and switch back to the MTA.
INSTALLATION MANUAL rev. 12
IVI6000C
1
2.0 Safety First
!
Please read and take time to understand all instructions:
Caution
a)
b)
c)
Never install telephone wiring during a lightning storm.
d)
e)
Use caution when installing or modifying telephone lines.
f)
Installation personnel should avoid being in direct contact with non-insulated telephone wires or connector terminals.
Never install telephone jacks in wet locations unless the jack is specifically designed for use in wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network
interface.
Hazardous voltages may be present on the TELCO and MTA port while connecting the Intercom Interface to telephone
lines.
3.0 Installations
3.1.
Connection Diagram
Connection Using
Discrete Wiring
IVI6000
OR RJ-11
Intercom
3
Home Wiring
Home Wiring
Intercom
2
Home Wall Jack
Relay
Two pair 110 punch
block
3
3
2
1
MTA
Tel
Intercom
House Wiring
3.2.
Connecting the Intercom VoIP Interface Model IVI6000 with satin cords
1- Rectangle
TO Cable
Modem e-MTA
3- Triangle
Line 1: To House
Wiring
Line 2:
To Intercom/Telco
2- Telephone
To House Wiring
2
IVI6000C
INSTALLATION MANUAL rev.12
The Intercom VoIP Interface requires no external power connection. Each unit is independent and powered by
the MTA Port.
3.3.
Connecting the Intercom VoIP Interface Model IVI6000 with discrete wiring
Use a screwdriver to open the cover:
Place the insertion cap over the wires and push
straight down on the cap until the cap is flush with
the colored portion of the 110 block.
Place the cable in the wire retaining guides,
Close the cover.
4.0 Testing the Intercom Interface
1234567-
Power up the Cable Modem MTA.
Wait 30 seconds.
Verify the house telephones have dialtone and are connected to the Digital Phone Service. If not ring the
Digital phone port.
While on-Hook on the Digital Phone service, request a call from the building intercom.
Verify the house telephones ring.
Answer the call and hang-up.
Wait 10 seconds and verify the house telephones have dialtone and are connected to the Digital Phone
service.
Porting:
1- If the telephone number is not ported and the Digital Phone Service is not active, insert a fine object into the
reset hole on the top of the unit and push delicately. The unit will reset to the Telco/Intercom port.
2- Verify the house telephones have dial tone from the Telco/Intercom port.
3- The first ring on the Digital phone Port will activate the porting and the unit will default to the Digital Phone
port.
5.0 Troubleshooting
1.
The house telephones do not ring:
Disconnect the MTA to Intercom VoIP Interface connection at the MTA. Connect a telephone at the MTA. Call
the MTA number. If the telephone does not ring the problem is with the MTA or service activation. If the
telephone rings verify the MTA to Intercom Interface wiring and the Intercom VoIP Interface to house wiring.
2.
The house telephones do not ring with an incoming Intercom or Telco call:
Verify the Telco to Intercom Interface wiring.
INSTALLATION MANUAL rev. 12
IVI6000C
3
6.0 Limitations
The Intercom VoIP Interface must not be used with public coin phone service provided by the telephone company or on
party lines.
7.0 Technical Information
Intercom Line Operating Voltage:
Temperature:
Humidity:
Switch Time:
Ring Detection:
Regulatory:
14-60 VDC
-20 °F to +140 °F
75% Non condensing
1/2 to 2 ring cycles
60 VAC to 115 VAC at 20 Hz +- 20%
UL 1863 , FCC, CS03
Subscriber Unit Module Weight:
Approx. 2.5 oz
(factory set)
8.0 Regulatory
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a
label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
All jacks are RJ-11
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part
68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line
may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five
(5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local
telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the
format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If this equipment (IVI6000) causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this equipment model IVI6000, for repair or warranty information, please contact Sittelle Technologies,
www.sittelletech.com . If the equipment is causing harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
This equipment is of a type that is not intended to be repaired.
This equipment is not compatible with party lines. Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this IVI6005 does not disable
your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified
installer.
HU
UH
9.0 Warranty
Limited Warranty
U
Sittelle Technologies Inc... warrants to the original purchaser that this product is free from defects in materials or workmanship for a
period of one (1) year from the date of purchase. During the warranty period, the product will be repaired or replaced (with the same or
similar model) at our option, without charge for either parts or labor. This warranty shall not apply if the product is modified, tampered
with, misused, or subjected to abnormal working conditions.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE, AND SITTELLE TECHNOLOGIES INC. SHALL IN NO
EVENT BE LIABLE TO PURCHASER FOR INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND OR CHARACTER.
Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied
warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights that vary from state to state.
4
IVI6000C
INSTALLATION MANUAL rev.12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising