Model 325

Model 325
®
QR-25 Series
Model 325
Parts Manual
Record of Change 106
This manual contains important safety information and must be made
available to all personnel who operate and/or maintain this product.
Carefully read this manual before attempting to operate or perform
maintenance on this compressor.
Fill Out & Return Warranty Registration Card Located Inside
Manual No. 50215-106
October 2006 Edition
INTRODUCTION
TABLE OF CONTENTS
This manual provides information for the following
QR-25 Series, Model 325 (Record of Change 106)
compressor versions:
L
LS
LVD
Serial Number Identification ................................. 2
Ordering Replacement Parts ................................ 2
Quin-Cip Lubricant ................................................ 2
Control Version L
head assembly with 1 unloader tower &
a hydraulic unloader
Crankcase Lubricant Capacity ............................. 2
Crankshaft Group ............................................... 3-4
Crankcase Group ................................................ 5-6
Control Version LS
head assembly with 2 unloader towers, a
hydraulic unloader, & a pilot valve with
a check valve assembly
Bearing Carrier Groups
with oil filter ..................................................... 7-8
less oil filter ................................................... 9-10
Connecting Rod & Piston Groups
High Pressure .............................................. 11-12
Low Pressure ............................................... 13-14
Control Version LVD
head assembly with 2 unloader towers, a
hydraulic unloader, & a pilot valve with
a lockout & check valve
Cylinder & Head Groups
Control Version L ........................................ 15-16
Control Versions LS, LVD ........................... 17-18
These compressors are aircooled, two stage, two
cylinder, pressure lubricated compressors, with up
to 200 PSI continuous pressure capability (201 to 500
PSI intermittant pressure capability with proper
configuration; consult factory). The Model 325 has a
4.5" low pressure piston bore and a 2.5" high pressure piston bore and a 3" stroke and can be run at
400-900 RPM.
Head Assemblies
Control Version L ........................................ 19-20
Control Versions LS, LVD ........................... 21-22
Control Groups
Version L ........................................................... 23
Version LS ................................................... 24-25
Version LVD ................................................. 26-27
Pilot Valves .......................................................... 28
Pilot Valve Repair Kit .......................................... 28
Available options included in this manual:
-high pressure rated cylinder and head
-spin-on oil filter
-hooded air filter
-hooded air filter / silencer
Differential Setting Charts .................................. 28
Suction Valve Unloader Assemblies .................. 29
Gasket Set ............................................................ 30
Kits ....................................................................... 30
Recommended Spare Parts ................................ 31
CHANGES
Decals ................................................................... 31
since previous printing dated March 2005:
Typical Unit Repair Parts List ........................ 32-34
Control groups were redesigned.
QR 325
50215-106, October 2006
Quincy Compressor
1
3501 Wismann Lane, Quincy IL - 62305-3116
MODEL &
SERIAL NUMBER
IDENTIFICATION
QUIN-CIP LUBRICANT
®
Refer to the chart below to order Quin-Cip compressor lubricant from your local authorized Quincy distributor.
Record
of
Change No.
Model & Serial Number
Identification Tag
The model & serial number tag is located on the
handhole plate side of the crankcase. Fill in the
numbers from your compressor's tag in the corresponding spaces provided here and reference this
page when ordering replacement parts.
All replacement parts are to be ordered through an
authorized Quincy distributor. Insist on genuine
Quincy parts only! Failure to do so may void warranty.
Package
Part No.
Description
Barrel
Pail
Gallon
Gallon Case
Quart
Quart Case
112541D032
112541P032
112541G032
112541X032
112541Q032
112541C032
55 gal., SAE 10W
5 gal., SAE 10W
1 gal., SAE 10W
(4)-1 gal., SAE 10W
1 qt., SAE 10W
(12)-1 qt., SAE 10W
Barrel
Pail
Gallon
Gallon Case
Quart
Quart Case
112542D068
112542P068
112542G068
112542X068
112542Q068
112542C068
55 gal., SAE 20
5 gal., SAE 20
1 gal., SAE 20
(4)-1 gal., SAE 20
1 qt., SAE 20
(12)-1 qt., SAE 20
Barrel
Pail
Gallon
Gallon Case
Quart
Quart Case
112543D100
112543P100
112543G100
112543X100
112543Q100
112543C100
55 gal., SAE 30
5 gal., SAE 30
1 gal., SAE 30
(4)-1 gal., SAE 30
1 qt., SAE 30
(12)-1 qt., SAE 30
CRANKCASE LUBRICANT
CAPACITY
Model
325
ORDERING
REPLACEMENT PARTS
Less Filter
With Filter
11/2 Qts.(1.42 lit.) Add 10oz.(296 ml)
CAUTION !
Refer to the Quincy QR-25 Series instruction manual for
vital lubrication information.
Prompt service can be rendered on repair parts orders
if the following information is given:
CAUTION !
Item 1) the model number, record of change number, & serial number.
Item 2) the exact part number needed. (Do not
order by item numbers.)
Item 3) the exact quantity needed.
Item 4) the preferred type of transportation
Follow all safety precautions outlined in the QR-25 Series
instruction manual.
WARNING !
Do not operate this compressor without a totally enclosed
belt guard or any other required safety equipment.
DANGER !
Air used for breathing or food processing must meet OSHA
1910.134 or FDA 21 CFR 178.3570 regualtions. Failure to do
so may cause severe injury or death.
QR 325
50215-106, October 2006
Quincy Compressor
2
3501 Wismann Lane, Quincy IL - 62305-3116
CRANKSHAFT GROUP 110238
1.3
1.4
1.1
1.6
3.1
1.3
2
1.2
1.5
3.2
3.4
3.3
QR 325
50215-106, October 2006
Quincy Compressor
3
3501 Wismann Lane, Quincy IL - 62305-3116
CRANKSHAFT GROUP 110238
Item
Number
1
2
3
1.1
1.2
1.3
1.4
1.5
1.6
3.1
3.2
3.3
3.4
Qty.
1
1
1
2
1
1
1
1
1
1
2
2
2
Part
Number
110217
110216
110234
2755S
2585
2788
110705-F15
1466
110472X
4126R
110983-N23
116124-N02
110428N050
Description
crankshaft assembly
crankshaft (N.S.S.; order 110217)
orifice, 1/8 npt
pipe plug, 1/8 npt
bearing cone
bearing cone
pin
key
sheave assembly
sheave, 16", 2 groove, B sect., ccw (N.S.S.; order 110472X)
hex. screw, 1/2-13 unc x 3.50, grade 8 (@ 90 ft.-lbs.)
square nut, 1/2-13 unc
flatwasher
N.S.S. = Not Sold Separate
@ Indicates torque value in foot pounds (dry threads)
Note: For reversal of compressor rotation refer to QR-25 instruction manual.
QR 325
50215-106, October 2006
Quincy Compressor
4
3501 Wismann Lane, Quincy IL - 62305-3116
CRANKCASE GROUP 110237
QR 325
50215-106, October 2006
Quincy Compressor
5
3501 Wismann Lane, Quincy IL - 62305-3116
CRANKCASE GROUP 110237
Item
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
‡ 16
17
18
19
20
‡ 21
22
23
1.1
1.2
8.1
8.2
9.1
9.2
9.3
9.4
Qty.
1
1
1
*
*
*
*
*
4
1
1
1
1
1
1
1
1
3 ft.
1
1
1
1
1
1
1
1
6
1
1
1
1
Part
Number
5503X003
5503-003
2720
6294D
6294
6294A
6294B
6294C
123478-L10
5506X1
5506
6316
112031X001
112032-001
5783-002
110705-C11
112031-001
110515-031
1301
6272
6313
123157-116
6275
6273
1840
2322-1
123478-K12
110070-3
8270
123157-112
110919-010
Description
crankcase assembly
crankcase
bearing cup
bearing adj. shim, .002 steel
bearing adj. shim, .005 steel
bearing adj. shim, .007 steel
bearing adj. shim, .020 steel
bearing adj. shim, .005 paper
hex. screw, 3/8-16 unc x .75, grade 5 (@ 30 ft.-lbs.)
bearing adjustment plate assembly
adjustment plate
oil seal
breather assembly
breather tube
breather ball
roll pin, 3/32 x .81
breather body
copper tube, 5/16 o.d.
pipe plug, 3/8 npt
screen
gasket, inlet screw
"o"ring, 3/32 wide x .94 o.d.
gasket, inlet screw
inlet screw
gasket, inspection plate
inspection plate, oil filler type
hex. screw, 5/16-18 unc x 1.00, grade 5 (@ 12 ft.-lbs.)
oil gauge
inlet tube
"o"ring, 3/32 wide x .69 o.d.
tube fitting, 5/16 tube x 3/8 npt, 90°
Maintenance Parts
8.2
1
10.1
1
1
1
6316
oil seal
Parts for use with diester or phosphate ester synthetic based lubricants
14
22
22749-111
22749-116
22749-112
"o"ring, 3/32 wide x .62 o.d.
"o"ring, 3/32 wide x .94 o.d.
"o"ring, 3/32 wide x .69 o.d.
* Quantity as required
@ Indicates torque value (dry threads).
‡ Assemble item 21 into item 16 with Loctite® 609.
QR 325
50215-106, October 2006
Quincy Compressor
6
3501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP 110816-001
(with oil filter)
1.12
1.11
1.14
1.1
1.13
1.15
1.2
2
4
1.4
1.6
1.7
1.3
1.16
1.5
1.8
3
5
6
1.10
1.17
1.9
QR 325
50215-106, October 2006
Quincy Compressor
7
3501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP 110816-001
(with oil filter)
Item
Number
* 1
*
*
§
*
2
3
§ 4
5
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
1.17
* 6
Qty.
Part
Number
Description
1
1
1
2
1
1
1
1
1
1
1
6
2
1
1
1
1
1
2
1
1
6
1
1
110810-003
110810
2523
160005
123157-152
123157-112
160002-002
160075-001
160003
6285
110813-001
123777-J12
2719
5489
123157-011
124369-P02
1160
112857
6565
2755S
6312
123478-L12
110822
110825
bearing carrier assembly (N.S.S.; order 110810X003)
bearing carrier (N.S.S.; order 110810X003)
bearing cup
bushing
"o"ring, 3/32 wide x 3.44 o.d.
"o"ring, 3/32 wide x .69 o.d.
driveshaft
driveshaft key
pump gerotor
retaining ring
oil pump housing
hex. screw, 1/4-20 unc x 1.00, grade 5 (@ 6 ft.-lbs.)
pipe plug, 1/4 npt, hex socket
adjustment screw
"o"ring, 1/16 wide x .44 o.d.
jamnut, 9/16-18 unf
spring
needle valve
hole plug
pipe plug, 1/8 npt
gasket, bearing carrier
hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)
oil pressure gauge
stud
1
110814-001
160078
6 pack of oil filters
Oil Pump Repair Kit
includes "o"rings, driveshaft, key, pump gerotor, & retaining ring
Replacement Bearing Carrier Assembly
includes bearing carrier assy., oil filter, stud, & bearing carrier gasket
110810X003
Maintenance Parts
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* Can not be used with diester or phosphate ester synthetic lubricants.
§ Install with Teflon® tape.
QR 325
50215-106, October 2006
Quincy Compressor
8
3501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP 110816
(less oil filter)
1.12
1.11
1.14
1.1
1.13
1.15
1.2
2
4
1.4
1.6
1.7
1.3
1.16
1.5
3
1.8
1.10
1.9
QR 325
50215-106, October 2006
Quincy Compressor
9
3501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP 110816
(less oil filter)
Item
Number
1
*
*
§
*
2
3
§ 4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
Qty.
1
1
1
2
1
1
1
1
1
1
1
6
2
1
1
1
1
1
2
1
6
1
Part
Number
Description
110810-002
110810
2523
160005
123157-152
123157-112
160002-002
160075-001
160003
6285
110813
123777-J12
2719
5489
123157-011
124369-P02
1160
112857
6565
6312
123478-L12
110822
bearing carrier assembly (N.S.S.; order 110810X002)
bearing carrier (N.S.S.; order 110810X003)
bearing cup
bushing
"o"ring, 3/32 wide x 3.44 o.d.
"o"ring, 3/32 wide x .69 o.d.
driveshaft
driveshaft key
pump gerotor
retaining ring
housing
hex. screw, 1/4-20 unc x 1.00, grade 5 (@ 6 ft.-lbs.)
pipe plug, 1/4 npt, hex socket
adjustment screw
"o"ring, 1/16 wide x .44 o.d.
jamnut, 9/16-18 unf
spring
needle valve
hole plug
gasket, bearing carrier
hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)
oil pressure gauge
160078
Oil Pump Repair Kit
includes "o"rings, driveshaft, key, & retaining ring
Replacement Bearing Carrier Assembly
includes "o"rings, driveshaft, key, pump gerotor, & retaining ring
Maintenance Parts
110810X002
1.2
1.3
1.12
1
1
1
Parts for use with diester or phosphate ester synthetic based lubricants
22749-152
22749-112
22749-011
160078-001
"o"ring, 3/32 wide x 3.44 o.d.
"o"ring, 3/32 wide x .69 o.d.
"o"ring, 1/16 wide x .44 o.d.
Oil Pump Repair Kit
includes "o"rings, driveshaft, key, pump gerotor, & retaining ring
N.N.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
§ Install with Teflon® tape.
QR 325
50215-106, October 2006
Quincy Compressor
10
3501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110248
(high pressure)
TOP
GROOVE
6
6
SECOND
GROOVE
THIRD
GROOVE
Pip mark
or "T"
on top of ring
6
7
BOTTOM
GROOVE
5
7
Be sure to stagger ring gaps !
4
2
3
2
1.2
1.3
9
1.1
9
1.4
8
QR 325
50215-106, October 2006
Quincy Compressor
11
3501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110248
(high pressure)
Item
Number
1
2
3
4
5
6
7
8
9
* 9
* 9
4
4
1.1
1.2
1.3
1.4
1.2
Qty.
Part
Number
Description
1
1
1
2
2
2
1
1
1
3
2
2
2
40201
6442C- HP
6443
3493
1836
8648
110190-021
1530-001
111280
1652
111281
124471-L08
6444
connecting rod assembly (N.S.S.; order 6442HPX)
rod, connecting (N.S.S.; see maintenance parts)
bushing, connecting rod (N.S.S.; order 6440SR)
connecting rod bolt
washer
retaining ring
piston pin
piston , high pressure
oil ring expander
piston ring
oil ring rail
locknut, 3/8-24 unf (@ 35 ft.-lbs.)
insert, connecting rod (N.S.S.; see maintenance parts)
1
1
1
1
1
1
6444PR
6444-010PR
6440SR
1530-011
1530-021
8161A
1
4422-010
1
4422-020
1
1530X001
inserts, connecting rod (1 pair, standard size)
inserts, connecting rod (1 pair, .010 undersize)
replacement connecting rod bushing
piston, high pressure (.010 oversize)
piston, high pressure (.020 oversize)
Piston Ring Set (standard)
includes piston rings, oil ring rails & expander
Piston Ring Set (.010 oversize, light blue color code)
includes includes piston rings, oil ring rails & expander
Piston Ring Set (.020 oversize, yellow color code)
includes includes piston rings, oil ring rails & expander
Piston Assembly, high pressure (standard)
includes ring set, piston pin, retaining rings, & piston
Piston Assembly, high pressure (.010 oversize)
includes ring set, piston pin, retaining rings, & piston
Piston Assembly, high pressure (.020 oversize)
includes ring set, piston pin, retaining rings, & piston
Replacement Connecting Rod Assembly
includes connecting rod assembly, connecting rod inserts, & locknuts
1530X011
1530X021
6442HPX
Maintenance Parts
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* One pair required for each connecting rod assembly.
QR 325
50215-106, October 2006
Quincy Compressor
12
3501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110247
(low pressure)
10
7
Pip mark
or "T"
on top of ring
TOP
GROOVE
5
THIRD
GROOVE
6
SECOND
GROOVE
10
Be sure to stagger ring gaps !
5
2
BOTTOM
GROOVE
3
2
4
1.2
1.3
9
1.1
1.4
8
QR 325
50215-106, October 2006
Quincy Compressor
13
3501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110247
(low pressure)
Item
Number
1
2
3
4
5
6
7
8
9
10
1.1
1.2
1.3
1.4
Qty.
Part
Number
Description
1
1
1
2
2
2
1
1
2
1
1
2
2
2
40139
6442C
6443
3493
1836
8648
8646
8643
112781
112780
7351
124471-L08
6444
2584
connecting rod assembly (N.S.S.; see maintenance parts)
rod, connecting (N.S.S.; see maintenance parts)
bushing, connecting rod (N.S.S.; order 6443SR)
connecting rod bolt
washer
retaining ring
piston pin
piston, low pressure
oil ring expander
oil ring rail
piston ring
locknut, 3/8-24 unf (@ 35 ft.-lbs.)
insert, connecting rod (N.S.S.; see maintenance parts)
piston ring
1
1
1
1
1
6444PR
6444-010PR
6443SR
8643-010
8643-020
8166A
inserts, connecting rod (1 pair, standard size)
inserts, connecting rod (1 pair, .010 undersize)
replacement connecting rod bushing
piston, low pressure (.010 oversize)
piston, low pressure (.020 oversize)
Piston Ring Set (standard)
includes piston rings, oil ring expander, & rails
Piston Ring Set (.010 oversize, light blue color code)
includes piston rings, oil ring expander, & rails
Piston Ring Set (.020 oversize, yellow color code)
includes piston rings, oil ring expander, & rails
Piston Assembly, low pressure (standard size)
includes piston, piston pin, retaining rings & ring set
Piston Assembly, low pressure (.010 oversize)
includes piston, piston pin, retaining rings & ring set
Piston Assembly, low pressure (.020 oversize)
includes piston, piston pin, retaining rings & ring set
Replacement Connecting Rod Assembly (standard)
includes connecting rod assy., connecting rod inserts, & locknuts
Maintenance Parts
* 9
* 9
4
4
1.2
4434-010
4434-020
8643X
8643X010
8643X020
6442X
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* One pair required for each connecting rod assembly.
QR 325
50215-106, October 2006
Quincy Compressor
14
3501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 112071
(control version L)
QR 325
50215-106, October 2006
Quincy Compressor
15
3501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 112071
(control version L)
Item
Number
Qty.
Part
Number
1
2
3
* 4
5
6
7
8
9
10
11
12
13
14
14
14
15
1
1
1
1
1
1
1
7
2
2
2
4
6
1
1
1
1
6610-5
1833
7000
111496U
112073
123478-L10
6293-002
123115-06C
124393-025
3092
90386-N15
90386-N20
123478-L14
110377F100
110377H100
110377S100
110377E100
cylinder
gasket, cylinder to crankcase
gasket
head assembly (see page 23 for parts breakdown)
intercooler (N.S.S.; order Intercooler Replacement Kit)
hex. screw, 3/8-16 unc x .75, grade 5 (@ 30 ft.-lbs.)
clamp
lockwasher, 3/8
fitting
pipe elbow, 3/4 npt x 3/4 npt, 90°
counterbore screw, 1/2-13 unc x 1.50, grade 8 (@ 50 ft.-lbs.)
counterbore screw, 1/2-13 unc x 2.75, grade 8 (@ 50 ft.-lbs.)
hex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)
air filter
filter
air filter/silencer, hooded
air filter element, (fits110377F100 & 110377S100 filter)
1
111496X11L
1
111496-051
1
112088
Replacement Head Assembly
includes head assy., head gasket, copper tube & fittings
Replacement Head Assembly (for high pressure rated compressors)
includes high pressure rated head assy., head gasket, copper tube & fittings
Intercooler Replacement Kit
includes intercooler and nut / sleeve fittings
Description
Maintenance Parts
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* High pressure compressors and DNV certified applications require 111496HPS head in lieu of 111496 head and 6610-5HPS
cylinder in lieu of 6610-5 cylinder
QR 325
50215-106, October 2006
Quincy Compressor
16
3501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 112072
(control versions LS, & LVD)
QR 325
50215-106, October 2006
Quincy Compressor
17
3501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 112072
(control versions LS, & LVD)
Item
Number
1
2
3
* 4
5
6
7
8
9
10
11
12
13
14
or
14
or
14
15
16
17
Qty.
Part
Number
Description
1
1
1
1
1
1
1
7
2
2
2
4
6
1
6610-5
1833
7000
111496UU
112073
123478-L10
6293-002
123115-06C
124393-025
3092
90386-N15
90386-N20
123478-L14
110377F100
cylinder
gasket, cylinder to crankcase
gasket
head assembly (see page 25 for parts breakdown)
intercooler (N.S.S.; order Intercooler Replacement Kit)
hex. screw, 3/8-16 unc x .75, grade 5 (@ 30 ft.-lbs.)
clamp
lockwasher, 3/8
fitting
pipe elbow, 3/4 npt x 3/4 npt, 90°
counterbore screw, 1/2-13 unc x 1.50, grade 8 (@ 50 ft.-lbs.)
counterbore screw, 1/2-13 unc x 2.75, grade 8 (@ 50 ft.-lbs.)
hex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)
air filter
1
110377H100
filter
1
1
1
1
110377S100
3003
2706
2708
air filter/silencer, hooded
pipe tee, 1/4 npt x 1/4 npt x 1/4 npt
connector
tube fitting, 90° male elbow, 1/4 tube x 1/4 npt
1
1
110377E100
111496X11S
1
111496-052
1
112088
air filter element, (fits110377F100 & 110377S100 filter)
Replacement Head Assembly
includes head assy., head gasket, copper tube & fittings
Replacement Head Assembly (for high pressure rated compressors)
includes high pressure rated head assy., head gasket, copper tube & fittings
Intercooler Replacement Kit
includes intercooler and nut / sleeve fittings
Maintenance Parts
18
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* High pressure compressors and DNV certified applications require 111496HPS head in lieu of 111496 head and 6610-5HPS
cylinder in lieu of 6610-5 cylinder
QR 325
50215-106, October 2006
Quincy Compressor
18
3501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 111496U
(control version L)
QR 325
50215-106, October 2006
Quincy Compressor
19
3501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 111496U
(control version L)
Item
Number
* 1
2
3
4
5
6
‡ 7
** 8
9
10
11
12
13
14
15
16
17
18
19
20
21
2.1
2.2
2.3
2.4
2.5
3.1
3.2
3.3
3.4
16.1
16.2
16.3
16.4
16.5
Qty.
Part
Number
Description
1
2
1
1
1
1
1
2
1
1
1
1
3
4
3
16
3
4
1
1
1
1
1
1
1
1
1
1
1
6
1
1
1
3
3
111496
7277X1
7277
1815
1846
7270
1849
7271X004
7271-004
1819-002
1846
7270-2
110639
1852
5906
7480
114545-R15
1848
6925
6964
6965-001
3008
1556
7532X
40055
7483
1855
1818B
5910
7499
2710
2961-100
6928
6910
1857
head
valve assembly
valve bumper
seat
valve disc
valve spring
stud
discharge valve assembly
discharge valve bumper
discharge valve seat
valve disc
valve spring
spacer
gasket
valve cover plate
hex. screw, 7/16-14 unc x 1.38, grade 5(@ 50 ft.-lbs.)
bolt & jamnut assembly (bolt @ 60 ft.-lbs. - jamnut @ 50 ft.-lbs.)
gasket
platform
spacer
pin
holddown screw (@ 70 ft.-lbs.)
gasket
unloader piston assembly
unloader assembly (@ 75 ft.-lbs.) (N.S.S.; order 7483X)
unloader body
diaphragm
diaphragm cover plate
diaphragm disc
hex. screw, 1/4-20 unc x .75, grade 2 (@ 72 in.-lbs.)
fitting
pressure relief valve
plate
valve spring
valve pin
1
1
111496HPS
7277X
1
7277XU
2
7271X04
1
7483X
Replacement Head (for high pressure rated compressors)
Replacement Suction Valve Assembly
includes suction valve assy. & valve gasket
Replacement Suction Valve Assembly
includes suction valve assy., valve gasket, valve pins, & valve springs
Replacement Discharge Valve Assembly
includes discharge valve assy. & valve gasket
Replacement Unloader Assembly
includes unloader assembly, unloader piston assembly, valve gasket & pipe plug
Maintenance Parts
Parts for use with diester or phosphate ester synthetic based lubricants
16.2
1
1855S
diaphragm
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* High pressure compressors and DNV certified applications require 111496HPS head in lieu of 111496 head.
‡ Tighten and torque valve cover plate hex screws (item 7) prior to tightening valve clamp hex screws (item 8).
** Install with Loctite® 272 applied to threads.
QR 325
50215-106, October 2006
Quincy Compressor
20
3501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 111496UU
(control versions S, LS, LVD)
QR 325
50215-106, October 2006
Quincy Compressor
21
3501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 111496UU
(control versions S, LS, LVD)
Item
Number
* 1
2
3
4
5
6
‡ 7
** 8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
2.1
2.2
2.3
2.4
2.5
3.1
3.2
3.3
3.4
18.1
18.2
18.3
18.4
18.5
21.1
21.2
21.3
21.4
21.5
Qty.
Part
Number
Description
1
2
1
1
1
1
1
2
1
1
1
1
2
4
2
16
2
6
2
2
2
1
2
2
2
2
1
1
1
1
1
6
1
4
1
1
1
1
1
6
1 ft.
6
111496
7277X1
7277
1815
1846
7270
1849
7271X004
7271-004
1819-002
1846
7270-2
110639
1852
5906
7480
114545-R15
1857
6925
6964
6965-001
1642
6928
3008
1556
7532X
40055
7483
1855
1818B
5910
7499
2961-100
1848
40192
8272
1855
1818B
5910
7499
110515-025
6910
head
valve assembly
valve bumper
seat
valve disc
valve spring
stud
discharge valve assembly
discharge valve bumper
discharge valve seat
valve disc
valve spring
spacer
gasket
valve cover plate
hex. screw, 7/16-14 unc x 1.38, grade 5 (@ 50 ft.-lbs.)
bolt & jamnut assembly (bolt @ 60 ft.-lbs. - jamnut @ 50 ft.-lbs.)
valve pin
platform
spacer
pin
tube fitting, 90° male elbow, 1/4 tube x 1/8 npt
plate
holddown screw (@ 70 ft.-lbs.)
gasket
unloader piston assembly
unloader assembly (@ 75 ft.-lbs.) (N.S.S.; order 7483X)
unloader body
diaphragm
diaphragm cover plate
diaphragm disc
hex. screw, 1/4-20 unc x .75, grade 2 (@ 72 in.-lbs.)
pressure relief valve
gasket
unloader assembly (@ 75 ft.-lbs.), (N.S.S.; order 8272X)
unloader body
diaphragm
diaphragm cover plate
diaphragm disc
hex. screw, 1/4-20 unc x .75, grade 2 (@ 72 in.-lbs.)
copper tube, 1/4 o.d.
valve spring
1
1
111496HPS
7277X
2
7277XU
2
7271X04
1
7483X
1
8272X
Replacement Head (for high pressure rated compressors)
Replacement Suction Valve Assembly
includes suction valve assy. & valve gasket
Replacement Suction Valve Assembly
includes suction valve assy., valve gasket, valve pins & valve springs
Replacement Discharge Valve Assembly
includes discharge valve assy. & valve gasket
Replacement Unloader Assembly
includes unloader assy. (40055), unloader piston assy., valve gasket & pipe plug
Replacement Unloader Assembly
includes unloader piston assembly, unloader assembly (40192), & valve gasket
Maintenance Parts
Parts for use with diester or phosphate ester synthetic based lubricants
18.2 & 21.2 1
1855S
diaphragm
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* High pressure compressors and DNV certified applications require 111496HPS head in lieu of 111496 head.
‡ Tighten and torque valve cover plate hex screws (item 7) prior to tightening valve clamp hex screws (item 8).
** Install with Loctite® 272 applied to threads.
QR 325
Quincy Compressor
50215-106, October 2006
22
3501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 110855
(control versions L)
Item
Number
Qty.
Part
Number
Part
Number
1
2
3
1
3
3 ft.
0-200 PSI
110827-001
1642
110515-025
201-500 PSI
110827-002
1642
110515-025
113225
113225
Description
hydraulic unloader assembly
tube fitting, 90° male elbow, 1/4 tube x 1/8 npt
copper tube, 1/4 o.d.
Maintenance Parts
Hydraulic Unloader Repair Kit
includes diaphragm, stem assembly, inlet filter & fitting assembly,
spring (0-200 PSI) and spring (201-500 PSI, red color code)
Parts for use with diester or phosphate ester synthetic based lubricants
1
1
1
1
110827-003
110827-004
hydraulic unloader assembly (standard, 0-200 PSI)
hydraulic unloader assembly (high pressure, 201-500 PSI)
1/4 o.d. tube
from receiver
QR 325
50215-106, October 2006
Quincy Compressor
23
3501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 116112-175 & 116112-998
(control version LS)
* See page 28 for optional pilot valves that must be used with respective pressure ranges.
QR 325
50215-106, October 2006
Quincy Compressor
24
3501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 116112-999 & 116112-000
(control version LS)
* See page 28 for optional pilot valves that must be used with respective pressure ranges.
QR 325
50215-106, October 2006
Quincy Compressor
25
3501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 116115-175 & 116115-998
(control version LVD)
* See page 28 for optional pilot valves that must be used with respective pressure ranges.
QR 325
50215-106, October 2006
Quincy Compressor
26
3501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 116115-999 & 116115-000
(control version LVD)
* See page 28 for optional pilot valves that must be used with respective pressure ranges.
QR 325
50215-106, October 2006
Quincy Compressor
27
3501 Wismann Lane, Quincy IL - 62305-3116
PILOT VALVES
WARNING !
Not all pilots are for use with all compressor systems. Make
sure that the pilot you order is set within the safe operating
limits of your compressor. Failure to heed this warning
could result in an explosion.
QR 325
50215-106, October 2006
Quincy Compressor
28
3501 Wismann Lane, Quincy IL - 62305-3116
sors in the field, not equipped with a suction valve
unloader assembly, can be converted to constant
speed. Consult your local Quincy distributor for
assistance with conversion procedures.
SUCTION VALVE
UNLOADER ASSEMBLIES
Description
The Quincy suction valve unloader assembly consists of unloading arrangements on the suction valves,
having a plunger to contact the suction valve disc
and an unloader pilot valve (part no.s 113708-***,
110998-***, and 110832-*** & 111423-***) to automatically regulate the passing of receiver pressure
to the unloading arrangement.
Service
Application
Adjustment
Periodically check the filter & screens in the inlet of
the pilot valve to make sure they are free of obstructions. If they become clogged, remove and clean or
replace. Inspect the "o"ring located in the opposite
end of the pilot valve body for wear or damage;
replace if necessary.
Suction valve unloader assemblies are recommended
for use on Quincy compressors where the compressor is to run continuously and a constant pressure is
to be maintained. The purpose is to automatically
unseat the suction valve of the compressor when the
air supply is greater than the demand.
The unloading pressure is adjustable and is regulated by turning the hex nut (marked "unload adj."
in cross sectional illustrations of pilot valves). Turn
the hex nut clockwise to increase and counterclockwise to decrease the unloading pressure.
The differential (difference between unloading
and loading pressure) is set by turning the hex nut
(marked "differential adj." in the cross sectional
illustrations of the pilot valves). Increase the differential pressure by turning the hex nut clockwise decrease by turning counterclockwise. Tighten the
locknuts after adjustment.
Operation
Unloading occurs when receiver pressure is sufficient to overcome pilot valve spring pressure. The
check ball is then unseated, allowing receiver pressure to pass to the unloading arrangements. The
compressor will run unloaded until the receiver
pressure drops to a predetermined level. At this
time, the action of the ball is reversed, shutting off
receiver pressure to the unloader arrangement and
venting the unloader to atmosphere. This allows the
compressor to load. The drive, either electric motor
or combustion engine, runs continuously and must
be started and stopped manually.
CHECK VALVE ASSEMBLIES
1
Pilot valves 111423-*** & 110998-*** can be
locked out, for models equipped with dual control, to
provide automatic start/stop operation. The knurled
knob at the top of the pilot can be turned clockwise,
until it stops, to lock it out. A pressure switch is
required to stop the motor. Failure to use a pressure
switch, with the pilot valve locked out, could result
in unsafe conditions.
2
WARNING !
Check Valve Assembly Replacement Parts
A pressure switch must be incorporated whenever pilot
valve 111423-*** or 110998-*** is employed as part of the
control system.
Item
Qty.
#
1
2
The compressor will operate in the continous run
mode if the knurled knob is turned counterclockwise
until it stops.
1
1
Part
Number
Description
6194X2
123157-010
6196-002
Check Valve Assembly
"o"ring
disc
6194X3
Check Valve Assembly
(for use with diester or phosphate ester synthetic lubricants)
1
2
Installation
The pilot valve is to be connected to the air receiver
using a minimum of 3/8" o.d. copper tube. CompresQR 325
50215-106, October 2006
1
1
22749-010
6196-003
"o"ring
disc
Quincy Compressor
29
3501 Wismann Lane, Quincy IL - 62305-3116
Head Kit K325A
Item
#
Qty.
1
2
2
4
4
2
4
1
2
2
1
Part
Number
110377E100
1556
1855
1848
1852
1556
1846
7000
7270
7270-2
5700
Basic Compressor Repair Kit 110823-325
Item
#
Qty.
Description
air filter element
gasket
diaphragm
gasket, valve
gasket, valve cover
gasket, valve cover
valve disc
gasket, cylinder to head
valve spring
valve spring
gasket, intercooler
1
1
1
1
1
1
1
1
2
2
2
2
1
4
1
1
1
V.I.P. Kit 110516-325
Item
#
Qty.
1
2
6
4
2
6
2
2
1
Part
Number
110822
1855
1857
1846
6283
6910
7270
7270-2
7126
Part
Number
110190-021
110377E100
110610-002
110814
2720
2585
2523
2788
6443SR
6444PR
7270
7270-2
8161
1846
7126
8646
8166
Description
piston pin
air filter element
"o"ring kit
oil filter
bearing cup
bearing cone
bearing cup
bearing cone
connecting rod bushing
connecting rod inserts (1 pair)
valve spring
valve spring
ring set
valve disc
gasket set
piston pin
ring set
Overhaul Kit K325C
Item
#
Qty.
Description
oil pressure gauge
diaphragm
valve pin
valve disc
hydraulic unloader filter
valve spring
valve spring
valve spring
gasket set
2
1
1
1
1
1
4
2
2
Part
Number
6444PR
110377E100
110610-001
8161
8166
7126
1846
7270
7270-2
Description
con-rod bearing
air filter element
"o"ring kit
ring set
ring set
gasket set
valve disc
spring
valve spring
Gasket Set 7126
Item
#
Qty.
2
1
1
4
4
2
2
2
1
6
2
1
1
Overhaul Kit K325B
Item
#
Qty.
1
2
4
2
2
2
1
1
1
1
Part
Number
110377E100
1855
1846
6444PR
7270
7270-2
7126
8161A
8166A
6316
Description
air filter element
diaphragm
valve disc
connecting rod inserts (1 pair)
valve spring
valve spring
gasket set
ring set
ring set
oil seal
QR 325
50215-106, October 2006
Part
Number
1556
1833
1840
1848
1852
5700
6294
6294A
6294B
6294C
6294D
6312
7000
Description
gasket
gasket, cylinder to crankcase
gasket, inspection plate
gasket
gasket
gasket
bearing adj. shim, .005 steel
bearing adj. shim, .007 steel
bearing adj. shim, .020 steel
bearing adj. shim, .005 paper
bearing adj. shim, .002 steel
gasket, bearing carrier
gasket
Quincy Compressor
30
3501 Wismann Lane, Quincy IL - 62305-3116
Recommended Spare Parts
Item
#
Qty.
Part
Number
2
2
1
1
1
1
2
2
1
1
7277XU
7271X04
110822
160078
7126
113225
6444PR
1855
110832-051
110377E100
Description
replacement suction valve assy.
replacement discharge valve assy.
pressure gauge
oil pump repair kit
gasket set
hydraulic unloader repair kit
connecting rod inserts (1 pair)
unloader diaphragm
pilot repair kit
air filter element
DECALS
2
3
1
Decals for QR 325 Basic Compressor
Item
#
Qty.
Part
Number
1
2
1
1
110831
127889-A
3
1
127889-B
Description
serial number & nameplate
decal, CAUTION!/manual/
"Failure to follow..."
decal, DANGER! /
"Air used for breathing..."
* Not sold separate; order 127889.
QR 325
50215-106, October 2006
Quincy Compressor
31
3501 Wismann Lane, Quincy IL - 62305-3116
TYPICAL UNIT REPAIR PARTS LIST
The parts listed here are for standard QR 325 (up to 175 PSI) units and may or may not be applicable to custom built units. Check with
your local authorized Quincy distributor for parts that can be used for custom built units. Make sure the components you order are rated
within the safe operating limits of your system. If you are doubtful about which components to order, contact your local Quincy distributor.
(QR 325 simplex - horizontal tank - electric motor)
Part
Qty Number
Part
Number
Part
Number
120 gal.
113271-200
* 113281
111136-050
111136-100
110514-300
§ 110512-003
110513-200
110515-075
23271
1
1
1
1
1
1
1
3 ft.
2
60 gal.
113891-200
n/a
2713
111136-075
110514-300
110512-003
110513-200
110515-075
23271
80 gal.
113268-200
n/a
2713
111136-075
110514-300
110512-003
110513-200
110515-075
23271
1
1
1
1
3 h.p.
110357B065
110580-118
n/a
113242K001
5 h.p.
110357B068
115240
8928
113242K001
115/230v, 1Ø
1
4003
1 **127466I020
200v, 3Ø
8098
8099
Description
tank (200 PSI max. working pressure)
top plate
tank drain valve
ball valve
pressure gauge
pressure switch (135-175 PSI)
pressure relief valve (200 PSI)
! discharge tube (3/4" copper tube to be formed by customer)
compression fittings
drive belt
motor pulley
motor pulley bushing
belt guard assembly
230/460v, 3Ø
124517-006
124517-005
3 h.p. motor (ODP)
5 h.p. motor (ODP)
* 113281 top plate is also used for all QR 325 base mounted electric motor driven units.
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
** 230 volt only.
§ 2298-175 pressure switch on base mounted unit.
(QR 325 duplex - horizontal tank - electric motor)
Part
Qty Number
Part
Number
Part
Number
200 gal.
113469-200
113281
111136-050
111136-100
110514-300
110512-003
110513-200
110515-075
23271
1
2
1
1
1
2
1
6 ft.
4
80 gal.
113471-200
N/A
2713
111136-075
110514-300
110512-003
110513-200
110515-075
23271
120 gal.
113467-200
113281
111136-050
111136-100
110514-300
110512-003
110513-200
110515-075
23271
2
2
2
2
3 h.p.
110357B065
110580-118
n/a
113242K001
5 h.p.
110357B068
115240
8928
113242K001
2
2
115/230v, 1Ø
4003
* 127466I020
200v, 3Ø
8098
8099
Description
tank (200 p.s.i. max. working pressure)
top plate
tank drain valve
ball valve
pressure gauge
pressure switch (135-175 PSI)
pressure relief valve (200 PSI)
discharge tube (3/4" copper tube to be formed by customer)
compression fittings
drive belt
motor pulley
motor pulley bushing
belt guard assembly
230/460v, 3Ø
124517-006
124517-005
3 h.p. motor (ODP)
5 h.p. motor (ODP)
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
* 230 volt only.
QR 325
50215-106, October 2006
Quincy Compressor
32
3501 Wismann Lane, Quincy IL - 62305-3116
TYPICAL UNIT REPAIR PARTS LIST
The parts listed here are for standard QR 325 (up to 175 PSI) units and may or may not be applicable to custom built units. Check with
your local authorized Quincy distributor for parts that can be used for custom built units. Make sure the components you order are rated
within the safe operating limits of your system. If you are doubtful about which components to order, contact your local Quincy distributor.
(QR 325 vertical tank - electric motor)
Part
Qty Number
Part
Number
1
1
1
1
1
1
3 ft.
2
60 gal.
114948P200
110425-025
111136-075
110514-300
110512-003
110513-200
110515-075
23271
80 gal.
114949P200
110425-050
111136-075
110514-300
110512-003
110513-200
110515-075
23271
1
1
1
1
3 h.p.
110357B065
110580-118
n/a
113242K001
5 h.p.
110357B068
115240
8928
113242K001
1
1
115/230v, 1Ø
4003
* 127466I020
200v, 3Ø
8098
8099
Part
Number
Description
tank (200 PSI max. working pressure)
tank drain valve
ball valve
pressure gauge
pressure switch (135-175 PSI)
pressure relief valve (200 PSI)
! discharge tube (3/4" copper tube to be formed by customer)
compression fittings
drive belt
motor pulley
motor pulley bushing
belt guard assembly
230/460v, 3Ø
124517-006
124517-005
3 h.p. motor (ODP)
5 h.p. motor (ODP)
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
* 230 volt only.
(QR 325 gasoline engine driven - Kohler)
Part
Qty Number
base unit
1
1
1
1
1
1
2
1
1
1
1
1
3 ft.
2
113764
110258B074
5629
8927
113702K005
113143-003
113698
Part
Number
tank unit
113727P200
111136-025
111136-050
110514-300
110513-200
110258B074
5629
8927
113702K005
113143-003
113698
110515-075
23271
Part
Number
Description
tank (200 PSI)
top plate
tank drain valve
ball valve
pressure gauge
pressure relief valve (200 PSI)
drive belt
engine pulley
engine pulley bushing
belt guard assembly
throttle control, bullwhip cable
Kohler engine group, 11 h.p. (includes exhaust system & throttle control)
! discharge tube (3/4" copper tube to be formed by customer)
compression fittings
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
QR 325
50215-106, October 2006
Quincy Compressor
33
3501 Wismann Lane, Quincy IL - 62305-3116
TYPICAL UNIT REPAIR PARTS LIST
The parts listed here are for standard QR 325 (up to 175 PSI) units and may or may not be applicable to custom built units. Check with
your local authorized Quincy distributor for parts that can be used for custom built units. Make sure the components you order are rated
within the safe operating limits of your system. If you are doubtful about which components to order, contact your local Quincy distributor.
(QR 325 gasoline engine driven - Honda)
Part
Qty Number
base unit
1
1
1
1
1
1
2
1
1
1
1
1
1
113764
110258B074
5629
8927
113702-012
113143-002
113700-1
Part
Number
Part
Number
tank unit
113727P200
Description
tank (200 PSI)
top plate
tank drain valve
ball valve
pressure gauge
pressure relief valve (200 PSI)
drive belt
engine pulley
engine pulley bushing
belt guard assembly
throttle control, bullwhip cable
Honda engine group, 11 h.p. (includes engine & throttle control)
! discharge piping group (includes discharge piping and fittings3/4" copper tube to be formed by customer)
111136-025
111136-050
110514-300
110513-200
110258B074
5629
8927
113702-012
113143-002
113700-1
112266-323
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
(QR 325 diesel engine driven - Yanmar)
Part
Qty Number
base unit
1
1
1
1
1
1
2
1
1
1
1
1
2.5 ft.
2
113764
110258B074
5629
8927
113702K008
113143-001
114080-002
Part
Number
tank unit
113727P200
111136-025
111136-050
110514-300
110513-200
110258B074
5629
8927
113702K008
113143-001
114080
110515-075
23271
Part
Number
Description
tank (200 PSI)
base
tank drain valve
ball valve
pressure gauge
pressure relief valve (200 PSI, in tank)
drive belt
engine pulley
engine pulley bushing
belt guard assembly
throttle control
Yanmar diesel engine group, 10 h.p. (includes throttle control)
! discharge tube (3/4" copper tube to be formed by customer)
compression fittings
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.
QR 325
50215-106, October 2006
Quincy Compressor
34
3501 Wismann Lane, Quincy IL - 62305-3116
QUINCY COMPRESSOR
responsible for loss or damage in transit after having received “In Good
Order” receipt from the carrier. All claims for loss or damage in transit should
be made to the carrier.
TITLE & LIEN RIGHTS: The equipment shall remain personal property,
regardless of how affixed to any realty or structure. Until the price (including
any notes given therefore) of the equipment has been fully paid in cash, Seller
shall, in the event of Buyer’s default, have the right to repossess such
equipment.
PATENT INFRINGMENT: If properly notified and given an opportunity
to do so with friendly assistance, Seller will defend Buyer and the ultimate
user of the equipment from any actual or alleged infringement of any
published United States patent by the equipment or any part thereof furnished
pursuant hereto (other than parts of special design, construction, or manufacture specified by and originating with Buyer), and will pay all damages and
costs awarded by competent court in any suit thus defended or of which it may
have had notice and opportunity to defend as aforesaid.
STANDARD WARRANTY: Seller warrants that products of its own
manufacture will be free from defects in workmanship and materials under
normal use and service for the period specified in the product instruction
manual. Warranty for service parts will be Ninety (90) days from date of
factory shipment. Electric Motors, gasoline and diesel engines, electrical
apparatus and all other accessories, components and parts not manufactured
by Seller are warranted only to the extent of the original manufacturer’s
warranty.
Notice of the alleged defect must be given to the Seller, in writing with all
identifying details including serial number, type of equipment and date of
purchase within thirty (30) days of the discovery of the same during the
warranty period.
Seller’s sole obligation on this warranty shall be, at its option, to repair or
replace or refund the purchase price of any product or part thereof which
proves to be defective. If requested by Seller, such product or part thereof
must be promptly returned to seller, freight prepaid, for inspection.
Seller warrants repaired or replaced parts of its own manufacture against
defects in materials and workmanship under normal use and service for ninety
(90) days or for the remainder of the warranty on the product being repaired.
This warranty shall not apply and Seller shall not be responsible or liable
for:
(a) Consequential, collateral or special losses or damages;
(b) Equipment conditions caused by fair wear and tear, abnormal conditions of use, accident, neglect or misuse of equipment, improper storage or
damage resulting during shipping;
(c)Deviation from operating instructions, specifications or other special
terms of sale;
(d) Labor charges, loss or damage resulting from improper operation,
maintenance or repairs made by person(s) other than Seller or Seller’s
authorized service station.
In no event shall Seller be liable for any claims whether arising from breach
of contract or warranty or claims of negligence or negligent manufacture in
excess of the purchase price.
THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND
ANY OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED IN
LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE
HEREBY SPECIFICALLY EXCLUDED.
LIABILITY LIMITATIONS: Under no circumstances shall the Seller have
any liability for liquidated damages or for collateral, consequential or special
damages or for loss of profits, or for actual losses or for loss of production or
progress of construction, whether resulting from delays in delivery or performance, breach of warranty, negligent manufacture or otherwise.
ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of shipment of the equipment from the factory, Quincy Compressor / Ortman Fluid
Power will comply with the various Federal, State and local laws and
regulations concerning occupational health and safety and pollution. However, in the installation and operation of the equipment and other matters over
which the seller has no control, the Seller assumes no responsibility for
compliance with those laws and regulations, whether by the way of indemnity,
warranty or otherwise.
June 30, 2003
Quincy Compressor
STANDARD TERMS AND CONDITIONS
LEGAL EFFECT: Except as expressly otherwise agreed to in writing by an
authorized representative of Seller, the following terms and conditions shall
apply to and form a part of this order and any additional and/or different terms
of Buyer’s purchase order or other form of acceptance are rejected in advance
and shall not become a part of this order.
The rights of Buyer hereunder shall be neither assignable nor transferable
except with the written consent of Seller.
This order may not be canceled or altered except with the written consent
of Seller and upon terms which will indemnify Seller against all loss
occasioned thereby. All additional costs incurred by Seller due to changes in
design or specifications, modification of this order or revision of product must
be paid for by Buyer.
In addition to the rights and remedies conferred upon Seller by this order,
Seller shall have all rights and remedies conferred at law and in equity and
shall not be required to proceed with the performance of this order if Buyer
is in default in the performance of such order or of any other contract or order
with seller.
TERMS OF PAYMENT: Unless otherwise specified in the order acknowledgment, the terms of payment shall be 1% 15, net forty-five (45) days after
shipment. These terms shall apply to partial as well as complete shipments.
If any proceeding be initiated by or against Buyer under any bankruptcy or
insolvency law, or in the judgment of Seller the financial condition of Buyer,
at the time the equipment is ready for shipment, does not justify the terms of
payment specified, Seller reserves the right to require full payment in cash
prior to making shipment. If such payment is not received within fifteen (15)
days after notification of readiness for shipment, Seller may cancel the order
as to any unshipped item and require payment of its reasonable cancellation
charges.
If Buyer delays shipment, payments based on date of shipment shall
become due as of the date when ready for shipment. If Buyer delays
completion of manufacture, Seller may elect to require payment according to
percentage of completion. Equipment held for Buyer shall be at Buyer’s risk
and storage charges may be applied at the discretion of Seller.
Accounts past due shall bare interest at the highest rate lawful to contract
for but if there is no limit set by law, such interest shall be eighteen percent
(18%). Buyer shall pay all cost and expenses, including reasonable attorney’s
fees, incurred in collecting the same, and no claim, except claims within
Seller’s warranty of material or workmanship, as stated below, will be
recognized unless delivered in writing to Seller within thirty (30) days after
date of shipment.
TAXES: All prices exclude present and future sales, use, occupation,
license, excise, and other taxes in respect of manufacture, sales or delivery, all
of which shall be paid by Buyer unless included in the purchase price at the
proper rate or a proper exemption certificate is furnished.
ACCEPTANCE: All offers to purchase, quotations and contracts of sales
are subject to final acceptance by an authorized representative at Seller’s
plant.
DELIVERY: Except as otherwise specified in this quotation, delivery will
be F. O. B. point of shipment. In the absence of exact shipping instruction,
Seller will use its discretion regarding best means of insured shipment. No
liability will be accepted by Seller for so doing. All transportation charges are
at Buyer’s expense. Time of delivery is an estimate only and is based upon
the receipt of all information and necessary approvals. The shipping schedule
shall not be construed to limit seller in making commitments for materials or
in fabricating articles under this order in accordance with Seller’s normal and
reasonable production schedules.
Seller shall in no event be liable for delays caused by fires, acts of God,
strikes, labor difficulties, acts of governmental or military authorities, delays
in transportation or procuring materials, or causes of any kind beyond Seller’s
control. No provision for liquidated damages for any cause shall apply under
this order. Buyer shall accept delivery within thirty (30) days after receipt of
notification of readiness for shipment. Claims for shortages will be deemed
to have been waived if not made in writing with ten (10) days after the receipt
of the material in respect of which any such shortage is claimed. Seller is not
QR 325
50215-106, October 2006
35
3501 Wismann Lane, Quincy IL - 62305-3116
Recipr
ocating / Systems:
Reciprocating
217.222.7700
Air Master
217.277.0270
E-mail:
Website:
info@quincycompressor.com
quincycompressor.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising