Airing
GB TRKK 6850
Start
Pause
QUICK REFERENCE GUIDE
Programme
selection
Please also carefully read the
“Instructions for Use”.
Drying options
Kg
95’
135’
80’
110’
3.0
5.0
80’
110’
60’
90’
3.0
5.0
60’
90’
50’
70’
3.0
5.0
25’
45’
20’
35’
1.0
2.5
Synthetics
20’
35’
15’
25’
1.0
2.5
max 2.5 kg
Delicate
30’
20’
1.5
-
Time
Synthetics
Cotton
Indicative
drying
times (in
minutes)
Airing
Very Wet Load
Wet Load
Load
Buzzer & Anti-Crease
cannot be selected
together
Gentle
Reduces drying
intensity
(recommended
for delicate
items)
Fabric
programmes
& Drying
levels
Dryness
Anti-Crease
Buzzer
Adjustment
Prevents
Signals/
(Adjusts
Dryness Level Sounds end of laundry from
creasing
drying cycle
according to
at Intervals
wishes)
Start Delay
Delays the
drying cycle
start
Start delay
Cupboard extra dry
Cotton
Cupboard dry *
max 5 kg
Remaining time
indication
Iron dry *
-
Cupboard dry *
Dryness
Adjustment
-
Iron dry
Delicate
Especially for delicate items
(e.g. shirts).
-
-
Laundry is aired and
refreshed for 30 minutes
without heating.
-
-
Water
Container
Completes drying or dries
single items (suitable for all
fabrics).
-
-
End
max 1.5 kg
-
-
-
Airing
* Test programmes according IEC 61121
-
Filter
Starts the drying cycle. The Start/
Pause indicator lamp is blinking
during the selection phase.
Press to confirm the final selection.
Turn the programme selector knob to the
desired programme. The indicator next to
the programme name lights up. The start
indicator blinks to show, that the dryer is
in selection mode. After the Start / Pause
button is pressed the start indicator lamp
lights up and the programme starts.
Delays the drying cycle start from 1
up to 12 hours.
To select the start delay turn the
programme selector knob to the desired
programme, select the desired options
and press the start delay button. With
each touch of the start delay button,
drying cycle start is delayed by one hour.
Press the Start/Pause button to confirm
your final selection. Start delay indicator
blinks and the count-down is running by
reducing the time in one hour steps. The
count-down is indicated by the blinking of
the start-delay indicator located above the
button. During count-down the drum will
turn from time to time to redistribute the
laundry and the pump may be heard
working for a short time.
To cancel or to change the previously set
time turn programme selector knob to “0”
or open the door.
After cycle start a default drying time is
indicated depending on the selected
drying programme and the dryness
adjustment. After several minutes the
time will be adjusted to the real expected
remaining time, depending on size, type
and humidity of the load.
Dryness adjustment is an option to adjust
the dryness of the laundry according to
your wishes. Select the desired
programme and the option dryness level
adjustment by pressing the button “+“ for
more dry or the button “–“ for more
humid. The selected dryness will be stored
as a pre-setting to the selected drying
programme. Using the drying programme
next time the pre-setting appears. By
pressing the dryness adjustment buttons
“+” or “–” the pre-setting can be changed.
The indicator lamp lights up when the
filter needs cleaning. Clean the filter at
the end of every cycle.
Lights up when water container needs to
be emptied. The drying cycle is
automatically interrupted. Empty the
water container. Press the Start/Pause
button to restart the dryer and to
continue the programme.
PROGRAMME SEQUENCE INDICATION
The programme sequence is indicated
by lamps, switching on when
programme step starts and switching
off when the programme step is
passed.
5019 407 00124
PREPARING THE LAUNDRY
SELECTING A PROGRAMME & OPTIONS
DAILY MAINTENANCE & CLEANING
1. Check that all fastenings are closed and
that pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to
make sure it doesn’t become tangled.
Sort laundry as follows:
A) By care symbols (on the collar or
inside seam):
Programme and Options:
• To select a programme, turn the
programme selector knob to the
required position. The Start/Pause
indicator lamp is blinking, indicating
that the cycle needs to be started.
• To select an option, press the
corresponding button. The indicator
light above the button lights up
confirming that the selection has been
made.
• Press the option button again to cancel
the option.
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Open the filter.
4. Remove lint using a soft brush or your
fingertips.
5. Close the filter.
6. Push the filter back into place.
Empty the water container at the end
of every drying cycle.
1. Pull the handle to remove the water
container.
2. Empty the water container.
3. Replace the water container when
empty by pushing it completely back
in place.
Suitable for tumble drying
Tumble drying with reduced
drying intensity only. Press
gentle button
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds
dryer capacity, separate laundry
according to weight (e.g. towels from
thin underwear).
C) By type of fabrics
Cotton/linen: towels, cotton jersey,
bed and table linen made of cotton or
linen.
Synthetics/Easy Care: blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry: woollens, silk, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such
as sleeping bags, etc.
Important: only use specific indicated
dryer-safe additives and rinse items
that have been treated with stain remover
thoroughly in plenty of water before
drying. Only use specific indicated
dryer-safe plastic items and never dry
rubber or articles contaminated with
vegetable oil in the dryer
STARTING & COMPLETING A
PROGRAMME
1. Having selected the desired
programme and options, press the
Start/Pause button.
If the laundry is not removed at the
end of the drying cycle, an automatic
anti-crease cycle will operate for
maximum 60 min. The drum rotates at
regular intervals, preventing the
laundry from creasing.
Anti-Crease protection redistributes laundry in the drum.
When the Anti-Crease option is
selected and laundry has not been
taken out, an anti-crease cycle is
activated for 12 hrs.
2. On completion of the programme, set
the programme selector knob to
position “0”.
CHANGING A PROGRAMME
When changing the programme during
the drying cycle, the dryer stops. The Start/
Pause indicator lamp is blinking.
To operate the new programme, press the
Start/Pause button.
INTERRUPTING A PROGRAMME
To interrupt the dryer during operation
1. Set the programme selector knob to
Airing.
2. Press the Start/Pause button.
Wait at least 5 minutes before opening
the door to allow the dryer to cool
down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close
the door and press the Start/Pause
button again.
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting our
After-Sales Service, make the
following checks to try and remedy
the problem:
Drying takes too long / laundry is not
dry enough:
• Was the correct programme selected?
• Was the inserted laundry too wet
(Washing machine spin speed less than
800 rpm? When the spinning speed is
less than 800 rpm the water container
fault may occur during the drying cycle)?
• Is the lint filter dirty (filter indicator
lamp on)?
• Is the heat exchanger dirty (refer to the
Instructions for use)?
• Is the ambient temperature too high?
The dryer does not operate:
(after a power failure and/or
interruption to the mains supply,
always press the Start/Pause button).
• Is the plug properly inserted into the
mains electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has the programme been selected?
• Has the start-delay option been
selected?
• Has the Start/Pause button been
pressed?
Lint filter or water container indicator
lamp on:
• Is the lint filter clean?
• Is the water container empty?
• Is the water container correctly
positioned?
• Is the heat exchanger clean?
Water droplets underneath the dryer:
• Is the heat exchanger correctly
positioned?
• Has any fluff on the heat exchanger
seal been wiped away?
• Has any fluff on the door seal been
wiped away?
• Has the water container been
positioned correctly?
All programme sequence indicators
blinking:
• Service call necessary.
Replacing the drum light bulb (if
supplied):
• If the inside lamp does not work, the
bulb may be faulty.
• Unplug the dryer.
• Open the door and unscrew the glass
cover insie the drum.
• Replace the faulty bulb with a new one
and screw the glass cover back on.
• Replacement bulb: Philips 15W,
230/240V, E14.
AFTER-SALES SERVICE
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales
Service (refer to guarantee).
Please specify:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the
word Service on the adhesive rating
plate) on the right-hand side when the
door is open.
• Your full address and phone number.
5019 407 00124
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising