Arc Edge manual - Mega Systems Inc

Arc Edge manual - Mega Systems Inc
USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………………. 3
Specifications……………………………………………………………………………………………………..4
Main Power Connection…………………………………………………………………………………..6
DMX-512 Connection…………………………………………………………………...……………...... 6
Installation Using 4356 DMX Controller…….………………………………………..……..7
Installation Using 4356 DMX Controller & 4357 Extender……..……..……..8
Installation Using 4380 ARC 124…...…….………………………………………..…………...8
Rigging the Fixture…………………………………………………………………………………………….9
Main Control Menu 4356 DMX Controller........................................................10
Main Control Menu 4380 Arc 124.......................................................................12
Cleaning & Maintenance..............................................................................................13
Parts List.............................................................................................................................13
Check that the unit has not been damaged during transport
Protection Against Fire
1.
2.
3.
4.
Maintain a minimum of 1 foot distance from any type of flame.
Do Not install the unit to close to a heat source.
Make sure cable are properly secured.
Maximum surface operating temperature 80ºC.
Protection Against Fire
1. Don't open unit there is no service parts inside.
2. For connection to main power supply proceed to pages 5.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3.
3
Specifications
4380– ARC Edge
Mechanical Specifications
Connection:
4-pin cable mounted connectors W/weather seal
IP Rating:
IP 65
Fastening System:
2 Base Mounting & 2 wall mounting plates
Material:
Aluminum Extrusion
Fixture:
Rear Cable track
39.37”
Fixture
1.63””
Packaged for Shipping
39.37” x 2.69” x 1.63”
40.5” x 4.5” x 3.5”
Weight 3.4
Weight 4lb
.50”
2.57”
1.30”
Electrical Specifications
LED Quantity: 64
Power Consumption: 21W
LED type: SMD 5050
LED Voltage: 24V
LED Lifetime: 60 to 100 thousand hours
Watts: 21W
Amps: .42
Reflector Angle: 60°
4356– DMX Controller
Mechanical Specifications
DMX Connectors:
3-pin XLR connectors
Power Connection:
External power supply bare cable
Fastening System:
2 fixture mounting points
2.65”
1.65”
Fixture
Packaged for Shipping
Size: 4.95”L x 2.65”W x 1.65”H
Size: 6”L x 3”W x 3.5”H
Weight: .6 lbs
Weight: 1.4 lbs
Electrical Specifications
Input Power:
DC5V~DC24V
Output Current:
6A Per channel (total 18A)
Output Power:
5V-90W
12V-220W
24V-450W
Brightness Control: 256 Scales
Control & Programming
Protocol:
DMX 512 / 1990
DMX Channels:
3
Control options:
Built in functions
4
4.95”
4357– Power Extender
Mechanical Specifications
Connectors:
Removable phoenix connectors
Power Connection:
External power supply bare cable
Fastening System:
2 fixture mounting points
Fixture
Packaged for Shipping
Size: 4.75”L x 1.56”W x 1.55”H
Size: 6”L x 3”W x 3.5”H
Weight: .4 lbs
Weight: 1.4 lbs
Electrical Specifications
Input Power:
DC5V~DC24V
Output Current:
6A Per channel (total 18A)
Output Power:
5V-90W
12V-220W
24V-450W
4359– ARC 124
Mechanical Specifications
DMX Connection:
5-pin terminal strip
LED connection:
8-pin terminal strip
Power connection :
2-pin terminal strip
Fastening System:
2 Base Mounting & 2 wall mounting plates
Material:
ABS plastic
Display:
3 digit display for DMX start channel
Temp Range:
-20°C - +50°C
Fixture
7”
.78”
Packaged for Shipping
7” x 1.80” x .78”
7.25” x 2” x 1”
Weight 1lb
Weight 1.25 lb
1.80”
Control & Programming
Protocol:
DMX 512 / 1990
DMX Channels:
Mode 3 Channel
Mode 4 Channel
R,G,B
R,G,B,W
4370–Power Supply 24V 60W / 4369-Power Supply 24V 120W
Input Voltage:
Output Voltage:
Listings:
100-240VAC50/60HZ
24V 60W max
UL Listed
Input Voltage:
Output Voltage:
Listings:
5
100-240VAC50/60HZ
24V 120W max
UL Listed
Main Power Connection
Caution!
1.
Do not connect fixture to a dimmer system.
The occupation of the connection-cable is as follows coming out of the AC to DC Power Supply
110V Connection
Cable (USA)
Cable (EU)
Pin
Red
Red
DC +
White
White
DC -
DMX-512 Connection
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or
the fixture with another.
DMX—output
DMX—input
2
1
1. Shield
1
2
2. Signal (-)
3
3. Signal (+)
3
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120
Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the
last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (HOS-DMXT).
6
Installation
Caution!
1. Each 24V 60W power supply will only power up to of 3 Arc Edge.
2. Each 24V 120W power supply will only power up to of 6 Arc Edge.
3. Do not connect more than 6 Arc Edge in one power supply
Installing using 4356-DMX Controller
Caution!
Cable may not be more than 100Ft from 4356-DMX Controller
DMX Controller
DMX Output
DMX Output
DMX Input
Caution!
Cable may not be
more than 100Ft
DMX Output
Caution!
Don’t connect more
than 3 Arc Edge
units using 4370
power supply
Power Supply
DMX Input
Power Supply
7
Caution!
Don’t connect more
than 6 Arc Edge
units using 4369
power supply
Installing using 4356-DMX Controller & 4357—Power Extender
DMX Controller
DMX Output
DMX Output
DMX Input
Caution!
Cable may not be
more than 100Ft
Caution!
Cable may not be
more than 100Ft
Power Supply
Power Supply
Caution!
Don’t connect more
than 3 Arc Edge
units using 4370
power supply
Caution!
Don’t connect more
than 6 Arc Edge
units using 4369
power supply
Caution!
Don’t connect more
than 3 Arc Edge
units using 4370
power supply
Caution!
Don’t connect more
than 6 Arc Edge
units using 4369
power supply
Installing using ARC 124
DMX Controller
DMX Output
DMX Input
DMX Output
Caution!
Cable may not be
more than 100Ft
Caution!
Cable may not be
more than 100Ft
Power Supply
Power Supply
Caution!
Don’t connect more
than 3 Arc Edge
units using 4370
power supply
Caution!
Don’t connect more
than 6 Arc Edge
units using 4369
power supply
8
Caution!
Don’t connect more
than 3 Arc Edge
units using 4370
power supply
Caution!
Don’t connect more
than 6 Arc Edge
units using 4369
power supply
+
V+
-
V—
3 CH mode
+
Red
4 CH mode
+
Grd
DMX Input
DMX Output
+
DMX +
-
DMX —
+
DMX +
-
DMX —
-
DMX Start Channel
0-5 0-9
0-9
Input 12-36Vdc
Output 108W max
Green
-
Arc Edge
V+
Power Supply
+
Blue
+
White
-
1. Shield = Grd
2. Signal (-) = DMX—
2
1
3. Signal (+) = DMX +
3
Rigging the fixture
Caution!
1.
2.
3.
4.
The installations must be carried out by an authorized dealer or trained professional.
Unit may cause severe injures if you have doubts concerning the safety do not install.
Unit is to be 24inches away from flammable materials (decoration material)
Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to
be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least
one time a year by a skilled person.
9
Main Control Menu For 4356 DMX Controller
1
GND
2
DATA —
3
DATA +
9 10
DMX 512 IN
FUN
256
8
128
6 7
064
016
4 5
008
3
032
2
004
001
1
002
The control board on the fixture base is your interface to
access and control all the functions on the unit. Its Dip
Switch gives you a code view of the options. The following
will explain each function and its options.
DMX 512 OUT
DMX Addressing
256
8
9 10
ON
256
4
5
6
FUN
128
7
128
3
064
064
2
1
002
032
9 10
ON
032
8
016
7
016
6
008
5
008
4
004
3
004
2
002
1
001
Turn dipswitch 10 to the OFF position. Each dipswitch from 1 to 9 holds a
numerical value located below the dipswitch. Add the numerical value to
get the desired fixture start address channel. The user must assign a
start address on the fixture that indicates the first channel reserved in the
controller.
001
DMX signal cable must be connected in order to respond to DMX mode.
For example, if you wish the first unit to start on address channel 85 you
will need to turn on dipswitch 1,3,5 and 7 (1+4+16+64=85)
Turn dipswitch 10 to the ON position. This function will turn on the functions that will allow the unit to run a preprogram function. Additionally, this
unit may serve as a master unit where other units will copy it’s functions.
To create a master unit connect the XLR cable from the output to the input on the next unit.
FUNCTION
RED
GREEN
BLUE
YELLOW
PURPLE
CYAN
WHITE
COLOR SNAP
COLOR FADE
FUNCTION
1
ON
2
3
4
5
6
7
8
9
FUN
Functions
10
ON
ON
ON
ON
ON
ON
SPEED 1 SPEED 2 SPEED 3 SPEED 4 SPEED 5 SPEED 6 SPEED 7
ON
SPEED 1 SPEED 2 SPEED 3 SPEED 4 SPEED 5 SPEED 6 SPEED 7
ON
RED
GREEN
BLUE YELLOW PURPLE CYAN WHITE COLOR S COLOR F
`10
ON
Testing
FUNCTION
RED
RED
RED
GREEN
GREEN
GREEN
BLUE
BLUE
BLUE
FUNCTION
1
33%
2
3
4
5
6
6
7
016
032
064
7
8
8
9 10
ON
9
10
33%
33%
33%
33%
33%
33%
33%
33%
OFF
DMX Profile
Arc Edge DMX Profile (3 Channels)
DMX Channel
1
2
3
FUN
5
256
4
128
3
008
2
004
1
002
Turn dipswitch 10 to the OFF position. This function will allow you to test
the intensity of each color or to set the color ribbon to a specific color.
001
For testing function do not connect DMX signal cable
Function
Led Color
Led Color
Led Color
Description
Red LED intensity
Green LED intensity
Blue LED intensity
11
Value
0-255
0-255
0-255
Main Control Menu For 4359 ARC 124
V+
-
V—
+
Red
3 CH mode
4 Channel
mode open
circuit.
4 CH mode
+
Grd
+
DMX +
-
DMX —
+
DMX +
-
DMX —
DMX Start Channel
-
DMX Start Channel
0-5 0-9
0-9
Input 12-36Vdc
Output 108W max
Green
-
V+
+
3 Channel
mode Close
circuit.
+
Blue
+
White
0-5
0-9
-
0-9
First Digit of DMX start Channel
Second Digit of DMX start Channel
Third Digit of DMX start Channel
DMX Profile
Arc 124 can be used for other constant voltage LED units that can use a 4 Channel control. But when used with the Arc Edge it
is only a 3 Channel fixture.
Arc Edge DMX Profile (3 Channels)
DMX Channel
1
2
3
Function
Led Color
Led Color
Led Color
Description
Red LED intensity
Green LED intensity
Blue LED intensity
12
Value
0-255
0-255
0-255
Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems
have to be removed.
Disconnect from mains before starting maintenance operation!
Caution Danger to life!
We recommend a frequent cleaning of the device. Please use a moist, lint free cloth. Never use alcohol or solvents!
1) The glass cover will require periodic cleaning on usage and environment. Environment with foggers will require more periodic cleaning as fog fluid tends to build up residues, reducing the light output.
Note: There is no serviceable parts inside the device. Maintenance and service operations are to be carried out by authorized
dealers.
Replacing the power cable: If the input cable of this device becomes damaged, it has to be replaced by authorized dealers only
In order to avoid hazards.
Should you have further questions , please contact your dealer.
Parts List
4380-LEDM
LED Module
4380-JC1M
1 Meter Jumper Cable
4380-JC5M
5 Meter Jumper Cable
4380-IC
Input Cable
4380-BM
Base Mount
4380-WM
Wall Mount
13
Warranty Information
Limited Warranty
Unless otherwise stated, your product is covered by a one year parts and labor limited warranty. Dichroic filters and glass gobos are not guaranteed
against breakage or scratches to coating. It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and dealer
or distributor. If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Material Authorization (RMA) number from your dealer or point of purchase BEFORE any units are returned for
repair. The manufacturer will make the final determination as to whether or not the unit is covered by warranty. Lamps are covered by the lamp
manufacturer’s warranty.
Any Product unit or parts returned to MEGA Systems Inc. must be packaged in a suitable manner to ensure the protection of such Product unit or
parts, and such package shall be clearly and prominently marked to indicate that the package contains returned Product units or parts and with an
RMA number. Accompany all returned Product units or parts with a written explanation of the alleged problem or malfunction. Ship returned Product units or parts to: 5711 Kenwick St. San Antonio TX 78254 USA.
Note: Freight Damage Claims are invalid for fixtures shipped in non-factory boxes and packing materials.
Freight
All shipping will be paid by the purchaser. Items under warranty shall have return shipping paid by the manufacturer only in the Continental United
States. Under no circumstances will freight collect shipments be accepted. Prepaid shipping does not include rush expediting such as air freight. Air
freight can be sent customer collect in the Continental United States.
REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
MEGA SYSTEMS INC. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, AND MEGA SYSTEMS SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MEGA
SYSTEMS SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS, SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PARTIAL
OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.
Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax 210-855-6279
www.mega-lite.com / info@mega-lite.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising