led double strip light led strip light
LED STRIP LIGHT
model no. 052-7846-2, 052-7848-8
LED DOUBLE STRIP LIGHT
model no. 052-7847-0, 052-7849-6
Toll-free: 1.866.827.4985
IMPORTANT: Please read this manual carefully and
save it for reference
Instruction Manual
2
Table of Contents
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985
model nos. 052-7846-2, 052-7848-8
Preparation
2
Know Your Strip Light
3
Parts List
3
Assembly
4-6
Safety
6
Troubleshooting
7
Linking Feature
8
Care and Maintenance
8
Warranty
9
Preparation
Please read and understand this entire manual before attempting to assemble, operate or
install the product. Save these instructions so you can refer to them at a later time.
Before beginning assembly and installation of product, make sure all parts are present.
Compare parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble, install, or operate the product.
Note: Keep your receipt and these instructions for proof of purchase. Estimated Assembly
Time: 45 minutes. Tools Required for Assembly (not included): wire strippers, safety
goggles, ladder, gloves, flathead screwdriver, cross-head screwdriver, electrical tape and
wire cutters.
!
READ AND SAVE THESE INSTRUCTIONS!
WARNING: RISK OF ELECTRIC SHOCK
Ensure the electricity to the wires you are working on is shut off. Either remove
the fuse or turn off the circuit breaker before removing the existing light fixture
or installing the new one.
1.
Fixture Plate
2.
Fixture Lens Cover
1
x1
2
Know Your Strip Light
3
1.
Drywall Anchor
2.
Mounting Screw
3.
Wire Connector
4.
Linking Connector
1
x2
3
x3
2
x2
4
x1
NOTE
Hardware not shown actual size.
Parts List
x1
4
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985
model nos. 052-7846-2, 052-7848-8
•With power disconnected to your electrical box, remove the existing fixture. Make a
sketch of how the current fixture is wired (by wire color) or mark the wires with masking
tape and a pencil so you will know how to properly reconnect the wires to the new LED
light fixture.
B
Assembly
A
B
1. Press the bottom frame of the fixture
plate (A) inward, in the direction of the
arrows, and lift the fixture lens cover (B)
with the other hand as indicated.
A
2. After dividing the light fixture into the
fixture plate (A) and fixture lens cover (B),
unplug the connectors to separate the
terminal wires and ground wire inside the
light fixture.
1
2
3
A
3. Turn over the fixture plate (A). Using a
screwdriver, punch out one of the 3 large
holes (1, 2, or 3) for wiring based on the
installation position.
A
4. Mark the two keyhole mounting
positions of the fixture plate (A) on the
ceiling. Drill a hole in the ceiling for each
of the two mounting holes.
5
AA
A
2
1
5. Install a plastic drywall anchor (AA)
and a mounting screw (BB) in each drilled
mounting hole.
A
2
1
Assembly
BB
6. Align the 2 mounting keyholes on
the fixture plate (A) with the 2 mounting
screws in the ceiling. Once both screw
heads are through the large ends of the
keyholes (position 1), slide the fixture plate
to the right until the heads of the screws
slide into the narrow ends of the keyholes
(position 2). Use a screwdriver to tighten
the mounting screws.
CC
7. Connect the wires from the fixture
plate (A) to the wires from the ceiling.
Follow the sketch or markings created when removing the old fixture to connect
wires of the same type or color, including
the ground wire. Cover the wire
connections using the wire connectors
(CC).
A
B
8. Connect the top and bottom parts of
the connectors for the terminal wires in
the light fixture, including the ground wire
of the fixture.
6
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985
model nos. 052-7846-2, 052-7848-8
A
B
DD
Assembly
9. Snap the fixture lens cover (B) onto
the fixture plate (A). Restore power to the
electrical box. Turn on the light switch to
activate the fixture.
10. Multiple light fixtures can be
connected end-to-end, up to the
maximum length shown below. Only the
first light fixture needs to be hardwired.
Each additional fixture is then mounted
to the ceiling and connected using the
linking connector (DD).
Safety
CAUTION:
1. If you are unfamiliar with electrical installations, it is recommended you contact a
qualified electrician to do the installation.
2. For indoor use only.
3. Suitable for damp locations.
4. Do not install inside enclosed cabinets.
5. Do not mount over stoves.
6. Do not leave bare wires exposed outside of the electrical connections.
7. Do not use this fixture with a dimming circuit. If you currently have dimmer controls, you will
need to remove them and replace them with regular electrical switches.
7
Problem
The fixture will not light.
The fuse blows or circuit
breaker trips when the light
is turned on.
Reason
Solution
The power is off.
Check to ensure the
power supply is on.
The circuit breaker is off.
Check to ensure the
circuit breaker is in the
on position.
There is a bad connection.
Check to ensure proper
wire connections
are made. Contact a
qualified electrician.
There is a defective switch.
Contact a qualified
electrician.
The wires are crossed
or the power wire is
grounding out.
Check to ensure proper
wire connections
are made. Contact a
qualified electrician.
NOTICE:
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Troubleshooting
Before doing any work on the fixture, disconnect power to the light fixture. Minor
problems often can be fixed without the help of an electrician.
8
Linking Feature
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985
model nos. 052-7846-2, 052-7848-8
Product
Linkability
Item # 052-7848-8 – 2 ft. (61 cm.)
LED Strip Light
Connect up to 30 2 ft. (61 cm.)
1-light strips
Item # 052-7846-2 – 4 ft. (1.2 m.)
LED Strip Light
Connect up to 15 4 ft. (1.2 m.)
1-light strips
Item # 052-7849-6 – 2 ft. (61 cm.)
LED Double Strip Light
Connect up to 15 2 ft. (61 cm.)
2-light strips
Item # 052-7847-0 – 4 ft. (1.2 m.)
LED Double Strip Light
Connect up to 7 4 ft. (1.2 m.)
2-light strips
CAUTION:
Care and Maintenance
Before attempting to clean the fixture, disconnect the power to the fixture by turning the
breaker off or removing the fuse from the fuse box.
This LED light fixture is made from quality materials that will last many years with
minimum care. You may want to periodically clean the fixture with a soft cloth. To
maintain the best appearance of the fixture, do not use cleaners with chemicals, solvents,
or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the
light fixture.
9
Warranty
This product carries a three (3) year warranty against defects in workmanship and
materials. Noma Canada agrees to replace a defective product, within the stated
warranty period, when returned to the place of purchase with proof of purchase.
This product is not guaranteed against wear or breakage due to misuse and/or abuse.
Made in China
Imported by
Noma Canada, Toronto, Canada M4S 2B8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising