warning - Home Depot

warning - Home Depot
IMPORTANT: Read and follow these instructions.
NOTICE
The installer must have electrical and mechanical training and acceptable knowledge in the
required work.
Safety is foremost---both your own and that of other
people. Many important safety instructions are provided
in this instruction and your appliance. Always read and
observe all safety instructions.
Level the pedestal on the clean place by adjusting
the feet.
WARNING
ENGLISH
Excessive Weight Hazard
Two or more people may be needed to install and
move the appliance and pedestal assembly.
Do not allow children to play on the drawer.
Do not step on the handle.
Lock nut
NOTE
Adjustable feet
A firm, solid floor is even more critical to a front-loading
washer than to a top-loader. If your floor is wooden
and /or frame construction, you may need to reinforce
it. Front-loaders have substantially faster spin speed
than top-loaders, causing greater vibration. If the floor
is not solid, your washer will vibrate.
Adjustable feet
NOTE
Do not extend the legs no more than necessary to
level the washer. The more the legs are extended, the
more the washer will vibrate.
Leg Extension
NOTE
If a drip pan must be used, take extra care to follow
the instructions provided with the drip pan and make
sure the leveling feet are adjusted for firm and even
contact with the pan. Use of drip pans and failure to
properly level the machine may result in increased
vibration and noise during operation.
After the washer is leveled, tighten the lock nuts up
toward the base of the washer using the wrench. All
four lock nuts should be tightened.
Position the washer/combo on top of the pedestal.
NOTE
WASHER/COMBO INSTALLATION
Because of the weight of the washer/combo, two or
more people may be needed.
Remove pedestal,installation hardware, and
instructions from the shipping carton.
NOTE
If the washer or combo was previously installed,
unplug it, disconnect the inlet hose (s)from the faucet
(s), disconnect the drain hose, and drain all hoses.
Before installing the pedestal, remove foreign
objects on the floor clean the floor. Dust, water, oil,
detergent and so on could cause vibration due to
bad contact of legs with floor.
for washer/combo
for dryer
for dryer
for washer/combo
2
Level the washer/combo on the pedestal by
adjusting the feet.
Move the washer/combo to the desired place.
NOTE
The appliance and pedestal assembly must be placed
on a solid and level floor for proper operation. Adjust
the legs of the appliance and pedestal by turning with
a wrench. Then, adjust the lock nut toward the
pedestal while holding the pedestal leg using a
wrench.
ENGLISH
Lock nut
Adjustable feet
Adjustable feet
Lock nut
Adjustable feet
Adjustable feet
NOTE
Diagonal Check
When pushing down the edges of
the washing machine top plate
diagonally, the machine should not
move up and down at all.(Please
check both directions.) If the
machine rocks when pushing the
machine top plate diagonally, adjust
the feet again.
Make sure the holes on the pedestal align with the
holes in the appliance, then install 4 screws at each
corner to securely attach the appliance to the pedestal.
NOTE
If the screws are not installed properly, noise and
vibration may result.
NOTE
To make sure that the washer is properly level, run the
washer with a test load: place approximately 6 pounds
of laundry in the machine. Then press POWER, press
RINSE+SPIN, and then press the START/PAUSE
button. See the following sections for additional
information on cycle selection and operation. Verify
that the washer does not rock or vibrate excessively
during the spin cycle. If the washer vibrates or shakes,
adjust the leveling feet until the washer is stable and
retest.
3
DRYER INSTALLATION
Remove pedestal,installation hardware, and
instructions from the shipping carton.
Make sure the holes on the pedestal align with the
holes in the appliance, then install 2 screws at each
corner to securely attach the appliance to the
pedestal.
ENGLISH
Insert the T-clip of the 4 retainers into the dryer base
as shown. Press up on the back of the clip and pull
outward to lock into place.
NOTE
If the screws are not installed properly, noise and
vibration may result.
T-clip
Retainer
Position dryer on top of the pedestal.
Move the dryer to the desired place.
NOTE
Because of the weight of the dryer, two or more people
may be needed.
NOTE
The appliance and pedestal assembly must be placed
on a solid and level floor for proper operation. Adjust
the legs of the appliance and pedestal by turning with
a wrench. Then, adjust the lock unt toward the
pedestal while holding the pedestal leg using a
wrench.
NOTE
If dryer was previously installed, uninstall it as follows:
A. Uninstalling an electric dryer:
1) Unplug the power supply cord,
2) Pull the dryer away from the wall enough to loosen
the vent clamp. Loosen the clamp and carefully
remove the exhaust vent from the dryer exhaust
outlet.
B. Uninstalling a gas dryer:
Lock
nut
1) Unplug power supply cord.
2) Turn off the gas supply.
3) Pull the dryer away from the wall enough to loosen
the vent clamp. Loosen the clamp and carefully
remove the exhaust vent from the dryer exhaust
outlet.
Adjustable
feet
Higher
Lower
for washer/
combo
for dryer
Adjustable
feet
for dryer
for washer/
combo
4
Adjustable
feet
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising