Stout Spout™ Electric Switch Kettle

Stout Spout™ Electric Switch Kettle
Stout Spout™ Electric Switch Kettle
with temperature gauge
BSS12ESKA Series
1.2L Electric Switch Kettle
Customer Service (North America): 1-888-538-8683
Local (Wyoming, USA): 307-222-6086
Email: help@mybrewista.com
READ THIS MANUAL PRIOR TO FIRST USE
AND SAVE FOR FUTURE REFERENCE
Household Use Only
1-year Limited Warranty
* Product appearance varies slightly between North American and all other markets.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed
including the following:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Read all instructions.
Do not touch hot surfaces. Use handles or knobs.
To protect against fire, electric shock and injury to persons, do not immerse cord,
plugs, base or kettle in water or other liquid.
Never leave the appliance unattended when in use. Close supervision is necessary
when any appliance is used by or near children.
Unplug from outlet when not in use, no water in kettle, filling water, moving kettle
and before cleaning. Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or has been damaged in any manner. Call our toll-free Customer
Assistance Number for examination, repair or adjustment.
Do not use a base unit other than the one supplied. The use of accessory attachments
not recommended by the appliance manufacturer may result in fire, electric shock
or injury to persons.
Do not use outdoors.
Do not let cord hang over edge of table or counter, or touch hot surfaces. Always
store excess portion of the power cord in the compartment of the base unit.
Electric kettle must be operated on a flat surface. Do not place on or near a hot gas
or electric burner, or in a heated oven, or on the top of other electric appliances.
Always attach plug to appliance first, then plug cord into the wall outlet. To
disconnect, turn control to off, then remove plug from wall outlet.
Do not use appliance for any purpose other than intended use.
To avoid circuit overload, do not operate another high wattage appliance on the
same circuit.
Do not fill kettle when positioned on base. Remove all moisture on the bottom of
the body before placing it onto the power base.
Be aware of steam being emitted from spout or lid especially during refilling. Do not
remove lid during boiling cycle.
Do not use the kettle to heat anything other than water. Do not fill above the ‘’max’’
indication. Do not operate kettle if water is below minimum marking. If the kettle is
overfilled, boiling water may be ejected. The kettle is only to use with the base unit
provided.
Do not insert any object into slots or holes of the kettle.
Scalding may occur if the lid is removed during the boiling cycles.
SAVE THESE INSTRUCTIONS
2
•
•
•
•
•
If the supplied cord is damaged, it must be replaced by the manufacturer, its service
agent, or a smilarly qualified person in order to avoid hazard.
The appliance can be used by children ages 8 years and older and persons with
reduced physical, sensory, or mental capabilities or lack the experience and
knowledge if they have been given supervision or instruction concerning the use
of the appliance in a safe way and understand the hazards involved. Cleaning and
user maintenance shall not be made by children unless they are older than 8 and
supervised.
Keep the appliance and its cord out of reach of children less than 8 years old.
WARNING: Do not remove the lid while water is boiling
WARNING: Position the lid so that steam is directed away from the handle.
SAVE THESE INSTRUCTIONS
3
ADDITIONAL SAFEGUARDS
DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY DAMAGE OR IF APPLIANCE
WORKS INTERMITTENTLY OR STOPS WORKING ENTIRELY.
EXTENSION CORDS
A short power-supply cord is to be provided to reduce the risk resulting from becoming
entangled in or tripping over a longer cord. Longer detachable power-supply cords or
extension cords are available and may be used if care is exercised in their use. If a longer
detachable power-supply cord or extension cord is used,
1) The marked electrical rating of the cord set or extension cord should be at least as
great as the electrical rating of the appliance, and
2) The extension cord should be a grounding-type 3-wire cord, and
3) The longer cord should be arranged so that it will not drape over the countertop
or tabletop where it can be tripped over, snagged, or pulled on unintentionally
(especially by children).
GROUNDING INSTRUCTIONS
This appliance must be grounded while in use.
CAUTION: To ensure continued protection against risk of electric shock, connect to
properly grounded outlets only.
GROUNDING INSTRUCTIONS
In North American markets, the appliance has a plug that looks like Figure A. Kettles sold
outside of North America include removable power cords for use with electrical outlets
in those markets. DO NOT attempt to insert a power cord into an incompatible outlet.
Appliance damage, electrical system damage or physical harm may result. An adaptor,
as shown in Figure B, should be used for connecting a 3-prong grounding plug to a 2-wire
receptacle. The grounding tab, which extends from the adaptor, must be connected to a
permanent ground such as a properly grounded receptacle as shown in Figure C, using
a metal screw.
Circuit grounding conductor
connected properly
(A)
Grounding prong
Metal mounting
screw
Adapter
Adaptor
(B)
Grounding means
(C)
Cover of grounded
outlet box
Warning: This appliance utilizes a high wattage relay for arriving at the desired water
temperature. In some instances, this relay may cause slight flickering of lights on the
same circuit. It is best to use this appliance on a dedicated circuit or with all other
appliances off during this appliance’s use. It will not damage electrical systems but
caution should be used to not overload this circuit with other appliances running at the
same time.
4
Table of Contents
Cover/Customer Service Information
IMPORTANT SAFEGUARDS
ADDITIONAL SAFEGUARDS
Electric Switch Kettle Components Operation Illustrations
Operation Instructions
• Before First Use
• Kettle Operation
• Adjusting Kettle Lid Tension
• Changing Temperature Gauge
• Maintenance and Cleaning
• Storage
• Decalcifying
• Brewista recommends Cafetto™ Descaler
• Preparing Coffee
• High Altitude Users
Warnings and Technical Data
Correct Disposal of this Product 1-year Limited Warranty Information
Stout Spout™ Electric Switch Kettle
1
2
4
6
7
8
8
9
9
10
10
10
11
11
12
13
14
14
15
5
Electric Switch Kettle Components
2
3
4
1
5
6
7
8
9
1)
2)
3)
4)
5)
6)
7)
8)
9)
6
Spout
Temperature Gauge
Lid
Thermometer
Handle
Max and Min water level indicators
On/Off Switch with Indicator Light
Base
Power Plug with Power Cord
◦◦ Kettles sold outside of North America
include removable power cords to
accommodate electrical outlets in
those markets.
Stout Spout™ Electric Switch Kettle
Operation Illustrations
A
B
C
D
E
F
G
H
I
Stout Spout™ Electric Switch Kettle
7
Before First Use
• Remove all packaging materials, labels and/or stickers from your kettle.
• Clean your kettle thoroughly before using for the first time (see Cleaning).
• Boil water at least 2 times and dispose, before boiling water for
•
•
•
•
•
consumption.
Remove the kettle from the base (8). Take off the lid (3).
Fill the kettle with water (ill. A) up to the max 1.2 L marking.
After filling the kettle with water, insert the lid (3) into kettle with holes
facing away from the handle.
Connect the power plug (9) to a wall outlet (ill. C). Press down the On/Off
switch (7) to the “On” position to start boiling the water (ill. D).
◦◦ If your kettle includes a removable power cord, insert the female end
of that cord into the base first.
The indicator light illuminates. After boiling is finished, the kettle turns off
automatically. Dispose of the hot water in the sink.
WARNING: Be careful when handling hot water. Danger of scalding!
•
Let the appliance cool down 1 minute before boiling water again. Repeat this
process before using water for consumption.
WARNING: Do not immerse the base (8), power cord (9), or the kettle in
water or any liquids. This may cause electric shock or damage
the appliance.
8
Stout Spout™ Electric Switch Kettle
Kettle Operation
Before plugging the kettle into the wall outlet, check that the electrical circuit is not
overloaded with other appliances.
•
Set the base (8) on a flat, even and steady surface.
•
Remove the kettle from the base (8). Take off the lid (3).
•
Fill the kettle with water (ill. A) under the “Max 1.2” marking. Do not fill over
the “Max” marking. See the water level (6) for adding the desired amount
of water.
•
Connect the power plug (9) to a wall outlet (ill. C).
◦◦ If your kettle includes a removable power cord, insert the female end of
that cord into the base first.
•
Press down the On/Off switch (7) to the “On” position to start boiling the
water (ill. D). The indicator light illuminates.
•
After boiling is finished, the kettle turns off automatically.
•
Let the appliance cool down 1 minute before boiling water again.
•
Pour the hot water into a heat resistant container (ill. E).
•
Manually interrupt the boiling process by lifting up the “On/Off” switch (7)
to off position.
•
After each use remove the power plug (9) from the wall outlet (ill. C).
WARNING: The appliance is very hot during use. Do not touch (ill. G).
Danger of burns!
WARNING: Never leave the kettle unattended while boiling water. Especially
when there are children nearby.
WARNING: Do not open the lid (3) while boiling water.
Adjusting Kettle Lid Tension
If you feel the kettle lid is too hard or too easy to remove
from the kettle, please follow the steps below to adjust
the tension:
1) Take the lid (3) off of the kettle.
2) Use a pair of needle-nosed pliers or similar tool to
adjust the three tabs of the kettle lid. If you push in
Lid Tab
the tab, the lid tension will be reduced and easier to put on and take off. If you
pull out the tabs the lid will be harder to pull off.
3) After adjusting the tabs, replace the lid and remove it again to see if your adjustment
is correct.
4) Repeat steps 2 and 3 until you have adjusted the lid to your preference.
Stout Spout™ Electric Switch Kettle
9
Changing the Temperature Gauge
• Unscrew the outer rim that secures the temperature gauge in place.
• Pull out the temperature gauge (ill. F).
• Replace with a new temperature gauge and re-assemble the lid.
Maintenance and Cleaning
• This appliance contains no user serviceable parts and requires little
•
•
maintenance.
◦◦ Refer any servicing or repairs to qualified personnel.
Clean the kettle regularly.
◦◦ Clean the outside of the base (8) and the kettle with a damp, soft cloth.
Clean the inside of the kettle with dish detergent and rinse thoroughly with
water.
◦◦ Do not use abrasive cleaners.
◦◦ After cleaning, dry the kettle and the base thoroughly.
WARNING: Never immerse the kettle or the base in water or other liquids.
WARNING: Always unplug kettle and wait for kettle to cool prior to cleaning.
Storage
•
•
10
Clean and dry all parts before storing. Store the kettle in its box or in a clean,
dry place.
Never wrap the power cord (9) around the kettle.
◦◦
Bases with attached power cords have cord storage underneath. Wrap
the attached cord around this feature.
◦◦
Removable power cords should be disconnected from the base and
stored properly.
Stout Spout™ Electric Switch Kettle
Decalcifying
• When mineral scale builds up in the kettle, it can affect temperature
consistency and slow down heating time.
To ensure optimum performance, Brewista recommends descaling the kettle
when mineral build-up is visible inside the kettle.
Note: Vinegar may not effectively descale the kettle and can be difficult to
thoroughly rinse. Vinegar may also leave behind an odor that could affect
future use.
•
Brewista recommends using Cafetto™ Descaler.
How to use Cafetto™ Descaler:
1) Mix 1 packet Cafetto™ Descaler
with 40 oz. of lukewarm water.
2) Pour the solution into the kettle.
3) Bring the solution to a boil.
4) Let the vessel cool for 15 minutes,
then discard the solution.
5) Rinse thoroughly with fresh water.
Stout Spout™ Electric Switch Kettle 11
Preparing Coffee
Pour Over Manual Brew Coffee
This is the simplest coffee brewing approach. It allows the individual the most control
of saturation of the coffee grounds, also the most participation by the user. It requires
more time than hitting the ON switch of a drip coffee maker but for many, its higher
involvement is part of the pleasure of coffee overall.
A
C
D
M AX
E
B
A.
B.
C.
D.
Grinder
Scale (Brewista Smart Scale™ recommended)
Paper filter, cloth or permanent filter
Pour over filter basket (Brewista Smart
Dripper™ recommended)
E. Drinking cup or carafe
F. Method for boiling water (Brewista kettle
recommended)
Brewing Manual Pour Over Method
•
•
•
•
•
•
Tips:
Measure about 6 ounces of water for each cup you intend to brew. Place
measured water in kettle and turn on kettle to bring the water to the desired
temperature.
Grind two tablespoons of beans per cup of coffee.
Rinse the filter, dripper, and glass server (or whatever you are brewing into)
in hot water to preheat them.
Assemble the filter, dripper and vessel and dump the ground coffee into
the filter.
When the water reaches a boil, take the kettle off the heat source and wait
about five to fifteen seconds. The desired coffee brewing temperature is
205o F, slightly lower than boiling temperature.
Now pour the water into the filter. Stir the coffee just a bit to be sure it all
gets saturated with water. A slow, steady pour allows for the best extraction
from the grounds.
• You may have to pour two or three times depending in the grind, filter size,
and amount of coffee being made.
• Pre-wetting the coffee grounds a minute before start pour over helps
extraction.
• A narrower spout allows better water flow control.
• Pour over coffee is usually ground finer than drip coffee maker, but not as fine
as espresso.
12
Stout Spout™ Electric Switch Kettle
High Altitude Users
At higher elevations water boils at lower temperatures. Use the graph below to determine
your kettle’s boiling temperature.
Stout Spout™ Electric Switch Kettle 13
WARNING: The appliance is very hot during use. Do not touch the
surface of the kettle. Danger of burns!
WARNING: Never leave the kettle unattended while boiling water,
especially if there are children nearby.
WARNING: Do not open the lid while boiling water.
WARNING: Do not immerse the base or the kettle in water or any
other liquid. This may cause electric shock or damage the
appliance.
WARNING: Be careful when handling hot water. Danger of scalding!
TECHNICAL DATA
For countries with voltage
ranging from 110-127V:
Rated voltage: 120 V ~60 Hz
Rated current: 10A
Rated power input: 1200W
Capacity: Max. 40.5 Oz (1.2L)
For countries with voltage
ranging from 220-240V:
Rated voltage: 220-240 V ~50/60 Hz
Rated power input: 1500W
Capacity: Max. 40.5 Oz (1.2L)
Correct Disposal of this Product
This symbol indicates that this product should not be disposed of
with other household wastes throughout the European Union. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact
the retailer where the product was purchased. They can collect
this product for environmentally safe recycling.
14
Stout Spout™ Electric Switch Kettle
LIMITED WARRANTY
1-Year Limited Warranty from the date of original purchase.
1. This warranty extends only to the original consumer, purchaser, or gift recipient.
Keep the original sales receipt, as proof of purchase is required to make a warranty
claim. The product must be purchased at an authorized retailer for the warranty to
be valid.
2. Defects that occur due to improper connection, improper handling, poor water
quality, or repair attempts by non-authorized persons are not covered by the
warranty. The same applies for failure to comply with the use of consumables
(e.g. cleaning and decalcifying agents) that do not correspond to the original
specifications.
3. Routine wear parts (e.g. seals and valves, permanent filter) and fragile parts, like
glass, are excluded from the warranty.
4. Damages which are not under responsibility of the manufacturer are not covered
by the warranty. This is valid, especially for claims arising from improper use (e.g.
operation with wrong type of current or voltage).
5. The guarantee becomes void if repairs are carried out by third parties, who are not
authorized by the manufacturer to do so and/or if spare parts are used other those
from the original equipment manufacturer.
6. Failure to comply with any important safeguards listed in section 1 will void the
limited warranty.
7. Household-use only.
To make a warranty claim, do not return this appliance to the store. Please email
help@mybrewista.com or call 1-888-538-8683. For faster service, locate the model,
type, and serial numbers on your appliance and have available for the call or include in
your email.
Stout Spout™ Electric Switch Kettle 15
Stout Spout™ Electric Switch Kettle
with temperature gauge
BSS12ESKA Series
1133 W. 27th Street, Cheyenne, WY 82001, USA | www.mybrewista.com
Toll Free in North America: 888-538-8683 | Local: 307-222-6086
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising