linea 450 led - Villa Lighting
LINEA 450 LED
Specification
The LINEA series features distinctly linear design qualities
and exceptional versatility. Perceptively capturing today's
minimal design philosophy, the reduced form is sure to
retain its validity far into the future. It is available in three
mounting heights in single or twin mounting configurations.
The pedestrian-scale model is 15 feet, with intermediate
and larger sizes at 20 and 26 feet, respectively, giving
proper scale for a variety of applications. Units for bi-level
mounting are available, where the street-side luminaire
is mounted high and a second fixture is mounted on the
sidewalk side at a lower height for pedestrian illumination.
An LED illuminating bollard for low-level pathway illumination
complements the family of products. CSA Listed for Wet
Locations
Color
Model LED Module Temperature
2LV - 2 LEVO
LN450 Modules
WW -3000K
NW - 4000K
Distribution
ME - Type III
S - Type II
Volt
Mounting Pole
UNV A - Single 15SR - 15' Straight
120-277V Mount
Rectangular
B - Twin
Mount
X - Other (specify)
Pole
Mat
Finish
SG - Silver
A - Aluminum
Grey
SSteel
GG Graphite
Grey
CC - Custom
Color
Ordering Information
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > LINEA
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/LINEA/
Page 1
Option
DIM - 0-10vDC
Dimming
N - None
LINEA 450 LED
Specification
HOUSING
Rectangular luminaire housing with integral fitter is extruded aluminum with no visible welds. Frameless tempered glass lens
with decorative masking is hinged and secured in place with a single stainless steel quarter-turn fastener for tool-less access
to the optical compartment. Lens seals to the housing with one-piece silicone gasketing when closed. Housing is fitted with
stainless steel weather-tight strain relief bushing for the power cable exiting the rear of the housing. Luminaire mounts to
tenon on pole and secured with four socket head cap screws on top of the housing. Luminaire is available in single or twin
back-to-back mounting configurations. All hardware is stainless steel.
OPTICS
Optics include 2 individual LED modules. Each module consists of an aluminum core PCB with fourteen high-power LEDs and
a single piece prismatic lens molded from optical quality acrylic. The prismatic lens redirects light output from the individual
LEDs and is available in two distributions as a Type II (S optics) or Type III distribution (ME optics). Luminaire emits zero uplight
at 90 degrees horizontal and above and is suitable for use in all LEED lighting zones. LED circuit boards are equipped with
electrical disconnects to allow for future technology upgrades.
BUG RATING
Type II: B1-U0-G1
Type III: B1-U0-G1
LED DELIVERED LUMEN OUTPUT
3000K - Type II = 3332 lumens / Type III = 3323 lumens
4000K - Type II = 3793 lumens / Type III = 3788 lumens
NOTE : Due to rapid and continuous advances in LED technology, LED luminaire data is subject to change without notice and at
the discretion of HessAmerica. Consult factory for current technical data.
ELECTRICAL
Electronic LED driver supplies 500mA drive current to LED modules with input voltage range from 120v to 277v at 50/60Hz.
Power consumption is 50 watts.
LUMINAIRE WEIGHT: 22 lbs
LUMINAIRE EPA: 1.3 sq. ft
POLE
Aluminum:
Straight rectangular pole is 6.3" x 3.9" nominal and manufactured from seamless 6061 aluminum tubing and heat treated to
produce a T6 temper. Nominal wall thickness is 0.236". Sides of the shaft are flat with 1/8" radiussed corners. Flush mounted
hand hole cover is plasma cut with kerf not to exceed 1/8'' and includes triangular tamper-resistant locking device. Two piece
base cover is fabricated aluminum. Nominal pole height is 15'.
Steel:
Straight rectangular pole is 6.3" x 3.5" nominal and manufactured from cold drawn over mandrel, electric weld, mechanical
steel tubing with nominal wall thickness of 0.197". Sides of shaft are flat with 1/2" radiussed corners. Pole shall show no
seam along the shaft. Flush mounted hand hole cover is plasma cut with kerf not to exceed 1/8" and includes triangular
tamper-resistant locking device. Pole is hot-dip galvanized with coating inside and out, then lightly sanded prior to painting.
Two piece base cover is fabricated aluminum. Nominal pole height is 15'.
FINISH
Standard finish is finely textured matte silver grey metallic or graphite grey. Special colors available on request.
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > LINEA
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/LINEA/
Page 2
CERTIFICATION: CSA Certified for Wet Locations
INGRESS PROTECTION: IP65
WARRANTY
Limited product warranty period including LEDs is five years. Driver shall carry the manufacturer's limited warranty.
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > LINEA
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/LINEA/
Page 3
Additional information
Dimensions
Mounting Detail
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > LINEA
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/LINEA/
Page 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising