mondeo - BERTONI
MONDEO
CAR SEAT
ECE R44/04
GROUP 0, I
(0-18 kgs.)
MANUAL INSTRUCTION
EN
IMPORTANT! KEEP FOR FURTHER REFERENCES.
READ CAREFULLY!
Only suitable if the approved vehicles are fitted with
3-points static or 3-point retractor safety-belts.
Approved to UN/ECER Regulation No. 16 or other
equivalent standarts.
EXTREME HAZARD
Do not use in passenger
seats equipped with Airbags
(SRS)
WASHING INSTRUCTIONS
1. The car seat can be cleaned using lukewarm water and soap. Do not use aggressive cleaners
like abrasives or thinner.
2. The cover should be washed by hand at a maximum temperature of 30oC. Do not put in the
dryer, just airing it.
3. The plastic parts can be cleaned by using a wettish drapery. Please, do not use any solvate.
Fig1/a
Fig1/b
Fig1/c
A
B
J
Fig.2
GROUP 0
B
B
C
L
M
Fig.3
A
GROUP I
D
K2
D
K1
M
M
Fig4
E
Fig5
F
G
H
Fig6/a
Fig6/b
12-18kg
6-12kg
0-6kg
L
Fig7/a
Fig7/b
J
INSTALLATION OF THE CAR SEAT
“Group 0” /from birth to 9kgs./
Step 1. For Group 0, the car seat must only be used in the most reclined position (see fig. 1/а). The car
seat must never be used in any other position (fig. 1/b). To adjust the reclining position of the safety
seat pull the red handle (J) forward until the most recline forward position. Take off the basic wedge
and change the position as the picture position, then press it inside with a “click”. The basic wedge
must be in position B when used rearward facing. (fig. 2)
Step 2. The car seat must always be placed in rear facing position (fig.3). If your car has an airbag on
the Passenger seat the car seat must only be used on the rear seats in the vehicle (fig. 1/с).
Step 3. Secure the car seat onto the car seats using the car seat belts (see fig. 3).
Step 4. Pass the lap part of the seat belt under the base of the car seat into the two points marked by a
blue label (А) and fasten the clip to the corresponding buckle (М).
Step 5. Pass the upper diagonal part of the belt in the metallic buckle (В).
Step 6. Take the red Lock-off clip (D) and attach it to the shoulder belt directly above the buckle (fig. 4).
Step 7. Make sure that the belt is not twisted and strongly tightened before the Lock-off clip is
attached.
INSTALLATION OF THE CAR SEAT
“Group I” /from 9 to 18kgs./
Step 1. The basic wedge must be in position A when placed the car seat in forward facing position.
Step 2. Place the car seat in forward facing position on either the passenger or rear seat of the vehicle
by using the 3 point belt system which is installed in the car.
Step 3. Pass the 3 point belt system (lap and shoulder belt) through the red marked openings (fig. 4)
(К1 and К2) and through the upper metallic guide. Fasten the buckle (М) in the lock until “click” is
heard. (fig.5)
Step 4. At the same time the lap belt is pulled through the two plastic openings (fig. 4).
Step 5. Place and fasten the red Lock-off clip (D) on the shoulder belt directly above the buckle (fig. 5).
IMPORTANT – DO NOT USE THE CAR SEAT IN FORWARD FACING POSITION BEFORE THE
CHILD’S WEIGHT EXCEEDS 9kgs.
WARNING:
The forward facing position in Group I can only be done if the child has reached a weight over 9 kgs.
The car seat can be placed on the front passenger seat of the car by using the lap and diagonal belt
and there is no air bag. Do not use any load bearing contact points other than those described in the
instruction and marked on the car seat.
the vehicle seat buckle is not positioned in or in front of the specified belt guide.
Securing your child into the car seat:
- Place the child into the car seat and position the attached safety harnesses.
- Fasten the buckle (G) by joining the two parts of the belt (Е and F) together until a “click” is heard
(fig. 6/а). To strongly tighten the safety harness the car seat is equipped with a central belt system
(Н): it means that, if you pull on the belt on the front the harness system is tightened. To lose the belt
just press the metallic button with one hand and with the other hand simultaneously pull on the
harness system towards you. (fig. 6b)
- Make sure that the harness system is not twisted or jammed somewhere.
ALTERING THE POSITION OF THE
HARNESS SYSTEM DEPENDING ON
YOUR CHILD’S WEIGHT
- On the back of the car seat there are three pairs of openings which can be used to adjust the
position of the safety belt system to suit your child’s weight (fig. 7/а).
- The lower openings are suitable for children up to a weight of 6 kgs.
- The middle openings are suitable for children with weight from 6 to 12 kgs.
- The upper openings are suitable for children with weight from 12 to 18 kgs.
- The pairs of openings should not be lower than the child’s shoulders when the child sits in the car
seat (fig. 7/а).
- To change the position of the safety belt you must separate it from the connection component (L)
which is placed on the back side of the car seat (fig. 7/b).
- Pass the safety belt through the required openings and join it at the connection component (L).
- Make sure that the harness system is not twisted or jammed somewhere.
Дидис ООД - България
Шумен 9700, “Правда” 1
Тел.: 054/850 830
Факс: 054/850 839
e-mail: office@didis-ltd.com
Didis Ltd. - Bulgaria
Shumen 9700, “Pravda” 1 Str.
Tel.: +359 54 850 830
Fax: +359 54 850 839
e-mail: office@didis-ltd.com
www.bertoni-eu.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising