LC-1CH-MULTI Dimmer Module TOKISTAR LIGHTING

LC-1CH-MULTI Dimmer Module TOKISTAR LIGHTING
T O K I S TA R L I G H T I N G
INSTRUCTION MANUAL
LC-1CH-MULTI Dimmer Module
General
The LC-1CH-MULTI Dimmer Pack can be used with any of Tokistar’s LED Lighting Systems operating from our 6, 8
or 24 VDC LED Drivers. The maximum rating at 6 and 8 VDC is 5 amps. The maximum rating at 24 VDC is 4 amps.
This unit may be operated on different dimming protocols, which include:
DMX Mode - In this mode, each unit is independently addressable. Convenient In-Out terminals are provided for
connecting units in series.
ANALOG Modes - You may select between 0-10V or 1-10V Analog protocols. Convenient In-Out terminals are
provided for connecting units in series.
MANUAL Mode - You may select a light intensity the fixtures will operate at. In this case, no external dimming
device is required.
Delivery Packet
Check for transport damage.
You should be in possession of the following items:
1 LC-1CH-MULTI
1 Manual, 1 Screwdriver, 1 Connecting part
Technical Specifications
LC-1CH-MULTI
1 2 3 4 5 6 7 8 9 10 11 12
• Power Requirement
6~8VDC / 5A Max., 24VDC / 4A Max.
• Output
2-pin orange terminal connector for Analog out
3-pin orange terminal connector for DMX out
4-pin green terminal connector for LOAD (5A Max.)
• Input
• Housing
• Environmental Rating
• Control Protocol
• Connection
• Listing
• Operation temperature
• Dimensions
• Weight
PRECAUTIONS
2-pin black terminal connector for Power In
2-pin green terminal connector for Analog In
3-pin green terminal connector for DMX In
Black Plastic
IP20 / Dry Location Only
DMX-512 (1990), Analog (0-10 or 1-10VDC)
Terminal
CE certified / ETL Listed
0 degC to + 50 degC
3.6” (90mm) L x 1.6” (40mm) W x 0.8” (20mm) H
50g / 0.11 lbs
1. Read all instructions completely before beginning installation.
2. Turn off electricity before beginning installation.
3. All wiring is to be performed by a qualified electrician.
4. Installation must comply with the National Electrical Code, and all applicable codes.
5. Turn main supply to transformer on only after all connections are made and tested.
6. Use only LED Drivers provided by Tokistar with the system.
7. Components must be installed in enclosures suitable for the environment.
DMX Control Mode
On
For operation from devices using DMX protocol, flip dip-switch 10
to the “ON” position.
1 2 3 4 5 6 7 8 9 10 11 12
Off
DMX is an acronym for Digital Multiplex. This is a universal binary language used as a form of communication between intelligent devices. After setting dip-switch 10 to the “ON” position, you need to set the address
on the dimmer pack. If all dimmer packs have the same address setting, all will work in unison. You can set
dimmer packs to different addresses, so each one is operating independently.
Each dip-switch on the dimmer pack represents a binary value. A DMX address is set by
combining the dip switches so they add up to the value you wish to achieve.
On
Dip-Switch 1 address equals 1
Dip-Switch 2 address equals 2
Dip-Switch 3 address equals 4
Dip-Switch 4 address equals 8
Dip-Switch 5 address equals 16
Dip-Switch 6 address equals 32
Dip-Switch 7 address equals 64
Dip-Switch 8 address equals 128
Dip-Switch 9 address equals 256
1
2
3
4
5
6
7
8
9 10 11 12
Off
Start CH#
Switches On
Start CH#
Switches On
1
2
3
4
5
6
7
8
9
10
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
11
12
13
14
15
:
:
:
:
511
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
:
:
:
:
1,2,3,4,5,6,7,8,9
Example 1
Example 2
Dip
Switch
Value
Dip
Switch
1
4
16
21
1
4
7
8
1
3
5
=
=
=
=
Dimming Curve
There are two settings for the Dimming Curve.
With dip-switch 12 set to the “On” position, the Dimming Curve is Linear.
On
1 2 3 4 5 6 7 8 9 10 11 12
*
Off
With dip-switch 12 set to the “Off” position, the Dimming Curve is Non-Linear.
On
1 2 3 4 5 6 7 8 9 10 11 12
Off
Wiring Details
A maximum of 36 dimmer packs may be connected in series in the DMX Mode. For applications
exceeding 36 dimmer packs, an additional feed from the DMX device is required.
LED Driver
LED Driver
Input
100~240 VAC
LED Driver
LED Driver
DMX IN
DMX IN
DMX OUT
DMX OUT
DMX IN
Fixture
Page 2
LC-1CH-MULTI
Max. 36
1 2 3 4 5 6 7 8 9 10 11 12
Fixture
LC-1CH-MULTI
3
1 2 3 4 5 6 7 8 9 10 11 12
Fixture
LC-1CH-MULTI
2
1 2 3 4 5 6 7 8 9 10 11 12
LC-1CH-MULTI
Fixture
1 2 3 4 5 6 7 8 9 10 11 12
1
DMX IN
DMX OUT
DMX In
Value
= 1
= 8
= 64
= 128
= 201
Analog Setting 1-10VDC
On
For operation from devices using 1-10VDC protocol, flip dip-switch 11
to the “ON” position.
1 2 3 4 5 6 7 8 9 10 11 12
Off
The 1-10VDC setting is the norm in most cases, and does not require the system to send a separate power
signal to the dimming device. The dimming device derives its power from our LED Driver. Additionally, this
setting is based upon the protocol 0-1VDC = Off, and other voltage values above 1VDC directly correlate to
dim values. A maximum of 10 Dimmer Packs can be connected in series.
Dimming Curve
In this analog mode, there are two settings for the Dimming Curve.
With dip-switch 12 set to the “On” position, the Dimming Curve is Linear.
On
1 2 3 4 5 6 7 8 9 10 11 12
*
Off
With dip-switch 12 set to the “Off” position, the Dimming Curve is Non-Linear.
On
LED Driver
Off
LED Driver
LED Driver
Analog In
Analog Out
Analog Out
Analog In
Fixture
Page 3
Fixture
LC-1CH-MULTI
Max. 10
1 2 3 4 5 6 7 8 9 10 11 12
Fixture
LC-1CH-MULTI
3
1 2 3 4 5 6 7 8 9 10 11 12
LC-1CH-MULTI
Fixture
2
1 2 3 4 5 6 7 8 9 10 11 12
ANALOG
1-10V
LC-1CH-MULTI
1 2 3 4 5 6 7 8 9 10 11 12
1
LED Driver
Analog Out
Analog In
1 2 3 4 5 6 7 8 9 10 11 12
Analog Setting 0-10VDC
On
For operation from devices using 0-10VDC protocol, flip dip-switch 11
to the “Off” position.
1 2 3 4 5 6 7 8 9 10 11 12
Off
The 0-10VDC setting is not the norm in most cases, and requires the system to send a separate power
signal to the dimming device. The dimming device derives its power from some external source in this case,
and not from our LED Driver. Additionally, this setting is based upon the protocol 0VDC = Off, and other
voltage values directly correlate to dim values (eg. 8VDC= 80% brightness level). The maximum number of
dimmer packs to be connected in series is based upon the capacity of the dimming device.
Dimming Curve
In this analog mode, there are two settings for the Dimming Curve.
With dip-switch 12 set to the “On” position, the Dimming Curve is Linear.
On
1 2 3 4 5 6 7 8 9 10 11 12
*
Off
With dip-switch 12 set to the “Off” position, the Dimming Curve is Non-Linear.
On
LED Driver
Off
LED Driver
LED Driver
Analog In
Analog Out
Analog Out
Analog In
Fixture
Page 4
Fixture
LC-1CH-MULTI
Fixture
1 2 3 4 5 6 7 8 9 10 11 12
3
LC-1CH-MULTI
Fixture
1 2 3 4 5 6 7 8 9 10 11 12
ANALOG
0-10V
LC-1CH-MULTI
POWER
SUPPLY
2
1 2 3 4 5 6 7 8 9 10 11 12
LC-1CH-MULTI
1 2 3 4 5 6 7 8 9 10 11 12
1
LED Driver
Analog Out
Analog In
1 2 3 4 5 6 7 8 9 10 11 12
Manual Control Mode
In this mode, dip-switches 10 and 11 are flipped to the “Off” position.
Flip dip-switches 1~8 to set the intensity of LED product.
Each dip-switch represents a binary value.
On
1 2 3 4 5 6 7 8 9 10 11 12
Off
The intensity is set by combining the different dip-switches that will add up to the value you wish to achieve.
The intensity value of 255 would represent full intensity
On
Dip-Switch 1 address equals 1
Dip-Switch 2 address equals 2
Dip-Switch 3 address equals 4
Dip-Switch 4 address equals 8
Dip-Switch 5 address equals 16
Dip-Switch 6 address equals 32
Dip-Switch 7 address equals 64
Dip-Switch 8 address equals 128
1
2
3
4
5
6
7
8
9 10 11 12
Off
Intensity
Value
Switches On
Intensity
Value
Switches On
1
2
3
4
5
6
7
8
9
10
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
11
12
13
14
15
:
:
:
:
255
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
:
:
:
:
1,2,3,4,5,6,7,8
Example 1
Example 2
Dip
Switch
Value
Dip
Switch
1
4
16
21
1
4
7
8
1
3
5
=
=
=
=
Value
= 1
= 8
= 64
= 128
= 201
LC-1CH-MULTI
1 2 3 4 5 6 7 8 9 10 11 12
Fixture
LED Driver
TOKISTAR® LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: 714 772 7005 FAX: 714 772 7014
email: info@tokistar.com Website: tokistar.com
Version 1.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising