round staff ul

round staff ul
1
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
Caractéristique
Spot orientable encastré staff, basse luminance,
montage EASY 13 système, montage rapide sur BA13
Spot diamètre 50, iodure.
Feature
Recessed low luminance staff spot EASY 13 mounting
system for BA13.
Ceilling Diameter 50 mm, metal halid.
Montage sur staff préfabriqué
Mounting in prefabricated plaster
*
CLASSE
CLASSE
I
III
IP
20
F
960°
ROUNDSTAFF UL
Réf.
120v
Type
24390-ORUL12 ORUL12 Round staff UL
GX10 iodure 35W 12°
Puissance : 20-39 watts
Alimentation
Tension : 120-277 volts
Couleur
Blanc
Power: 20-39 Watts
Power Supply
Voltage: 120-277 Volts
230
ROUNDSTAFF UL
320
*in process
SOKA DISDEROT
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
2
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
DISCLAIMER
Warnings and cautions
Pay special attention to informations provided in warnings and cautions indicated by the icons below.
Without access above ceilin,g to change the ballast, you will have to reopen the ceiling whole of the fixture,
take then replace it.
A WARNING
Indicates a procedure or situation that, if not avoided,
could result in serious injury or death to the user.
A CAUTION
Indicates a procedure or situation that could result in
injury to the user or physical damage.
A WARNING
1. This product must be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazard involved.
2. Turn off power before you begin installation.
Do not turn it back on during installation work, this is very dangerous.
3. Repair and conversion work are strictly prohibited, to do so may result in a serious accident.
4. Use rated voltage only, malfunction may occur otherwise.
A CAUTION
1. Follow instructions provided by the power source manufacturer to assure proper connection
as this differs by manufacturer. Imperfect connections may result in an accident.
2. To prevent static damage, touch a metal to discharge static electricity from your body
before you touch ROUND STAFF UL. ROUND STAFF UL may be damaged if static electricity be
insufficiently discharged.
3. Make sure positive and negative connections are correct for wiring. Reverse connections
may cause a failure.
4. Do not pull the cables roughly during wiring. Cables may break if you pull them with too
much force. Pay careful attention to prevent a short circuit.
5. Join wires carefully so it’s not interfering with light emission.
6. Do not use ROUND STAFF UL for purposes other than his original purpose.
You shall be held responsible for failures or damages in the event of failure to observe this.
7. Use connection terminals, etc., in wiring and connection processes to assure connections
are correct and waterproof.
8. This is a built-in device, therefore a suitable enclosure shall be provided to prevent from any
access in the end product.
9. Screw plate junction box after connecting cables.
10. Be careful, do not forget to put the removable plate include in the box.
SOKA DISDEROT
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
3
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
RELAMPING
20 WATTS & 39 WATTS
20 WATTS
1. Utiliser une ampoule de remplacement
de maximum 20 watts, type MR 16
[désignation ANSI de l’ampoule].
2. Protection inhérente.
3. Accès requis au-dessus du plafond.
4. Attention, risque d’incendie.
5. Pour emplacements secs seulement (
SOKA/OVALSTAFF ou ROUNDSTAFF /
120 V – 277 V – 20 W).
6. Ne pas mettre l’isolant à moins de 76
mm (3 po) de toute partie du luminaire.
7. Si l’ampoule de ce luminaire à
protection thermique clignote, cela
peut signifier une surchauffe.
8. Utiliser seulement dans des
installations où le degré de résistance
au feu n’est pas établi.
1. Relamp with max 20 watts type MR 16
[lamp ANSI designation] - format s24-l1
2. Inherently protected.
3. Access above ceiling required.
4. Caution – risk of fire.
5. Dry locations only ( SOKA/OVALSTAFF
ou ROUNDSTAFF / 120 V – 277 V – 20W).
6. Do not install insulation within 76 mm
(3 in) of any part of the luminaire.
7. Blinking light of this thermally protected
luminaire may indicate overheating.
8. For use in non-fire-rated installations
only.
39 WATTS
1. Utiliser une ampoule de remplacement
de maximum 39 watts, type MR 16
[désignation ANSI de l’ampoule].
2. Protection inhérente.
3. Accès requis au-dessus du plafond.
4. Attention, risque d’incendie.
5. Pour emplacements secs seulement (
SOKA/OVALSTAFF ou ROUNDSTAFF /
120 V – 277 V – 39 W).
6. Ne pas mettre l’isolant à moins de 76
mm (3 po) de toute partie du luminaire.
7. Si l’ampoule de ce luminaire à
protection thermique clignote, cela
peut signifier une surchauffe.
8. Utiliser seulement dans des
installations où le degré de résistance
au feu n’est pas établi.
SOKA DISDEROT
1. Relamp with max 39 watts type MR 16
[lamp ANSI designation] - format s24-l1
2. Inherently protected.
3. Access above ceiling required.
4. Caution – risk of fire.
5. Dry locations only ( SOKA/OVALSTAFF
ou ROUNDSTAFF / 120 V – 277 V – 39W).
6. Do not install insulation within 76 mm
(3 in) of any part of the luminaire.
7. Blinking light of this thermally protected
luminaire may indicate overheating.
8. For use in non-fire-rated installations
only.
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
4
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
INSTRUCTION MANUAL
1. Housing installation - Placoplâtre® (plaster board) version
1
Unpacking
2
Cut a hole in the ceiling (120x120 mm).
4
Adjust the ROUND
STAFF UL to the ceiling.
5
3
Pass the box and the dome
through the hole.
After ajusting the
ROUND STAFF, Insert the
screw throught the ceiling
to block and maintain the
fixture.
BA13
6
Straighten, sand and
put finish coat.
13
fixture
finish coat
SOKA DISDEROT
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
5
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
INSTRUCTION MANUAL
2. Connection and installation of mounted spot.
1
2
Spot overview after mounting.
3
Step 1
Step 2
Follow the order of the movable
part as shown.
Cut off general electricity.
ON / OFF
4
Step 3
Push the movable part
into the plaster.
Push
SOKA DISDEROT
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
6
__
6
solutions d’intérieur | SPOTS ORIENTABLES
ROUND STAFF UL
SOKA DISDEROT
Photo for information only. We reserve the right to modify product
design and specification without due notice.
J. LOUIS · SEPTEMBRE 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising