The Galley Tap Installation Instructions

The Galley Tap Installation Instructions
Installation Instructions
Stainless Steel Pull-down Kitchen Faucet
THEGALLEY TAP
™
Made in Italy
Installation
1
Install the Optional Base Ring by
slipping it over the hoses and
onto the Mounting Shank.
Optional
Base Ring
Mounting
Shank
2
Optional
Base Ring
Insert all hoses and Mounting
Shank through the hole in
countertop.
Minimum Ø 1-3/8”
hole in Countertop
3
Stainless
Steel
Washer
On the underside of the countertop,
install the stainless steel Washer
and Mounting Nut by slipping
them over the hoses and threading
the nut onto the Mounting Shank.
Tighten the Mounting Nut against
the countertop and tighten the
two screws
so the faucet is
secure.
Stainless
Steel
Mounting
Nut
Stainless Steel
Crosshead
Screws
2
Installation
4
Hand Spray
Hose
Install the Counterweight onto
the Hand Spray Hose as shown.
1”
Important:
Remove protective paper and stick
rubber strips inside counterweight
Counterweight
5
Hand Spray
Supply Hose
Connect the Hand Spray Hose
to the Hand Spray Supply Hose
on which the Check Valve housing
is fitted.
Check Valve
Housing
Note - make sure Hand Spray
Hose and Counterweight are free to
slide up and down and are not
in conflict with any plumbing
components or items under the sink
or Workstation.
Hand Spray
Hose
6
Cold
Supply
Hose
1. Before connecting the hot and
cold Supply Hoses, flush water
supply stops to clear any debris.
Place a bucket underneath the
stops and run water for 5 to 10
Hot
Supply
Hose
2. Carefully position hot and cold
supplies so they will not interfere
with other hoses.
3. Connect the 3/8" Compression
Connections (Hot and Cold Supply
Hoses) to your hot and cold inlets.
Hoses are marked hot and cold.
3
Usage
Faucet
turns
on
by
tilting
handle out. Tilting angle is 24°.
Handle
rotates
forward
for
temperature adjustment.
When Handle is in upright
position water temperature is
fully cold. When Handle is rotated
90° forward water temperature is
fully hot.
27”
Pull-out
Hand Spray
Hand Spray pulls out up to 27” from
the spout.
Adjust Slide Switch down for spray
flow or up for laminar flow.
Slide
Switch
On /
Cold
Hand
Spray
On /
Hot
Laminar Flow
Spray Flow
Maintenance
1. Cartridge Replacement:
a) Using an Allen Key, unthread
Set Screw from handle.
b) Unthread and remove Dome Cap
and Cartridge Nut.
c) Remove and replace Cartridge.
Use the 2 pins on the bottom of
the Cartridge to seat the
Cartridge correctly.
Handle
2. Check Valve Replacement:
a) Unthread Hose and Check
Valve Housing.
b) Remove and replace Check
Valves by inserting them O-Ring side
forward into Check Valve Housing.
c) Re-assemble.
Aerator
Aerator Locking Ring
Cartridge
Dome Cap
Aerator Key
Set Screw
Cartridge Nut
3. Aerator Replacement:
a) Use Aerator Key to remove
and replace Aerator.
Hand Spray
Supply Hose
O-Ring
4. Aerator Cleaning:
a) Clean aerator periodically
to eliminate any build-up.
Check Valve Housing
Check Valve
Hand Spray Hose
4
Care and Cleaning for The Galley Tap Finishes
ABOUT OUR FINISHES:
The Galley Tap is made of solid stainless steel. This finish has NO PROTECTIVE COATING on
it. Stainless steel is by its material nature very tarnish-resistant, but by no means tarnish or
stain proof. This finish will react to it’s environment over time. Cleaners that contain bleach
may cause rust. Keep your Galley Tap wiped clean and dry, and use only a cleaner specifically
made for stainless steel. Trapped moisture on the surface of your finish can lead to staining.
Astringent cleaners, chlorine, bleach, and acidic-based organic cleansers are potentially
harmful to stainless steel finishes.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying a stainless steel cleaner with a soft clean cloth
to gently remove surface spots and brighten the finish.
For PVD Satin Black and PVD Gun Metal Gray finishes, clean with a soft, warm damp cloth.
3. Never use cleaners with bleach, abrasives or vinegar. Never use any type of abrasive cleaning pad.
Replacement Parts
* XXX represents finish
1234567891011121314151617181920212223-
5
Handspray
Aerator & Ring
Aerator Key
O-Ring Gasket
Acetal Ring
Acetal Ring
Set screw
Cartridge
Cartridge Nut
Dome Cap
Handle
Set screw
O-Ring Gasket
Base Ring
O-Ring Gasket
Mounting Washer
Mounting Nut
Mounting Nut Screws
Gasket
Counterweight
Adhesive Strips
Check Valve
Hand Spray Hose
** From July 2017
X.1051-XXX *
A.362
S.203
O.052 **
S.292 **
S.293 **
A.128
S.232
B.709
B.710-XXX *
F.017-XXX *
A.356
O.066 **
B.711-XXX *
O.022
A.358
F.016
A.357
A.064
S.252
S.273
A.290
A.354
THE GALLEY TAP - LIMITED WARRANTIES
1. GALLEY TAP LIMITED MECHANICAL WARRANTY – Seller warrants its
products, installed in a residential application, to be free from manufacturing
defects in materials and workmanship for a period of five (5) years from the date
of purchase by the original consumer/owner. This limited warranty is subject to the
warranty conditions and limitations as set forth below.
2. GALLEY TAP LIMITED LIFETIME FINISH WARRANTY – For the following
Finishes: Polished Stainless Steel, Matte Stainless Steel, PVD Satin Black Stainless
Steel, and PVD Gun Metal Gray Stainless Steel, seller warrants its finishes, installed
in a residential application, to be free from manufacturing defects in materials or
workmanship for the useful life of the product from the date of purchase by the
original consumer/owner. Please refer to the Seller’s Care Instructions for the
proper maintenance of Seller’s finishes. This limited warranty is subject to the
warranty conditions and limitations as set forth below.
3. WARRANTY CONDITIONS AND LIMITATIONS – All of Seller’s warranties are
strictly limited to the first residential consumer of its product. Seller’s Mechanical
and Finish warranties are strictly limited to products correctly installed using our
installation instructions and used in a residential environment. Mechanical or finish
problems which result from abuse, misuse, improper installation, improper
maintenance or improper cleaning, proximity to bodies of salt water, or accidental
damage such as scuffs and scratches are not covered by this warranty. Seller does
not assume liability for labor charges, removal and re-installation expenses, freight
or postage charges, or injuries resulting from a defective product. This warranty
does not allow recovery of incidental or consequential damages such as loss of
use, property damage, or any other consequential damage and Seller accepts no
liability for such damage. Seller does not assume any responsibility other than to
repair or replace the defective part(s) after Seller, upon its examination, has
determined the product to be defective and the defective part(s) are covered by
the limited warranty expressed in this warranty. Whether to repair or replace the
product or its finish shall be at the sole election of the Seller. The use of Plumber’s
Putty will void this warranty. A non-corrosive epoxy silicone sealing compound
may be used. Seller hereby disclaims all other warranties, expressed or implied,
other than those set forth in this warranty.
Some states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
4. WARRANTY CLAIMS – These warranties are in effect for Seller’s Products
purchased on January 1st, 2017 and thereafter. For warranty claims, please contact
your Galley Dealer, or you may write to:
The Galley, LLC.
Attn: Warranty Claims
12626 South Memorial Drive
Bixby, OK 74008
Please include the original receipt with a description of the problem, model
number, store, date of purchase, name of installer, your name, address and
telephone number.
6
CORPORATE HEADQUARTERS
The Galley, LLC.
12626 South Memorial Drive
Bixby, OK 74008
800.375.4255
thegalley.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising