Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack
Operation Manual
Smart-UPS™ On-Line SRT
Uninterruptible Power Supply
SRT2200XLI
SRT2200RMXLI
SRT2200RMXLI-NC
SRT3000XLI
SRT3000RMXLI
SRT3000RMXLI-NC
SRT3000XLT
SRT3000RMXLT
SRT3000RMXLT-NC
SRT3000XLW-IEC
SRT3000RMXLW-IEC
208/220/230/240 Vac
Tower/Rack-Mount 2U
Product Description
The APC by Schneider Electric Smart-UPS™ On-Line SRT is a high performance uninterruptible power supply
(UPS). The UPS helps to provide protection for electronic equipment from utility power blackouts, brownouts,
sags, surges, small utility power fluctuations and large disturbances. The UPS also provides battery backup power
for connected equipment until utility power returns to acceptable levels or the batteries are completely discharged.
This user manual is available on the enclosed Documentation CD and on the APC by Schneider Electric web site,
www.apc.com.
General Information
Important Safety Messages
Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service
or maintain the UPS. The following special messages may appear throughout this manual or on the equipment to
warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning product safety label indicates that an electrical
hazard exists which will result in personal injury if the instructions are not followed.
The addition of this symbol to a Warning or Caution product safety label indicates that a hazard exists
that can result in injury and product damage if the instructions are not followed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.
NOTICE
NOTICE used to address practices not related to physical injury. The safety alert symbol is not used with this signal word.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
1
Safety and General Information
• Adhere to all national and local electrical codes.
• All wiring must be performed by a qualified electrician.
• Changes and modifications to this unit not expressly approved by APC could void the warranty.
• This UPS is intended for indoor use only.
• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or
humidity.
• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
• For a UPS with a factory installed power cord, connect the UPS power cable directly to a wall outlet. Do not
use surge protectors or extension cords.
• The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient
temperatures, poor quality utility power, and frequent short duration discharges will shorten battery life.
• Replace the battery immediately when the UPS indicates battery replacement is necessary.
• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
• The batteries are heavy. Remove the batteries before installing the UPS and external battery packs (XLBPs),
in a rack.
• Always install XLBPs at the bottom in rack-mount configurations. The UPS must be installed above the
XLBPs.
• Always install peripheral equipment above the UPS in rack-mount configurations.
• Additional safety information can be found in the Safety Guide supplied with this unit.
Deenergizing safety
The UPS contains internal batteries and may present a shock hazard even when disconnected from the branch
circuit (mains). Before installing or servicing the equipment check that the:
• input circuit breaker is in the OFF position.
• internal UPS the batteries are removed.
• XLBP battery modules are disconnected.
Electrical safety
• For models with a hardwired input, the connection to the branch circuit (mains) must be performed by a
qualified electrician.
• Have a proper grounding for input socket for the models with pluggable power cords.
• 230 V models only: In order to maintain compliance with the EMC directive for products sold in Europe,
output cords attached to the UPS must not exceed 10 meters in length.
Battery safety
• Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.
High short circuit current through conductive materials could cause severe burns.
• Do not dispose of batteries by burning them. The batteries may explode.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.
2
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
General information
• The UPS will recognize as many as 10 external battery packs connected to the UPS.
Note: For each XLBP added, increased recharge time will be required.
• The model and serial numbers are located on a small, rear panel label. For some models, an additional label
is located on the chassis under the front bezel.
• Always recycle used batteries.
• Recycle the package materials or save them for reuse.
FCC Class A radio frequency warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are intended to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
3
Product Overview
Specifications
For additional specifications refer to the APC by Schneider Electric web site, www.apc.com.
Environmental
Temperature
Elevation
Operating
0º to 40º C (32º to 104º F)
Storage
-15º to 45º C (5º to 113º F)
Operating
0 - 3,000 m (0 - 10,000 ft)
Storage
0 - 15,000 m (50,000 ft)
Humidity
0% to 95% relative humidity, non-condensing
Protection Class
IP 20 rating
Note: Charge the battery modules every six months during storage.
Environmental factors impact battery life. Elevated ambient temperatures, high humidity, poor quality mains power, and
frequent short duration discharges will shorten battery life.
Physical
SRT2200XLI/SRT2200RMXLI/SRT2200RMXLI-NC model
The UPS is heavy. Follow all lifting guidelines.
Lifting guidelines
18 - 32 kg (40 - 70 lb)
32 - 55 kg (70 - 120 lb)
Unit weight batteries included, without packaging
25 kg (55 lb)
Unit weight batteries included, with packaging
Rack-Mount models: 34 kg (75 lb)
Tower models: 31 kg (68 lb)
Unit dimensions without packaging
Height x Width x Depth
Rack-Mount models:
85 (2U) mm x 432 mm x 560mm
3.35 (2U) in x 17 in x 22 in
Tower models:
85 (2U) mm x 432 mm x 585mm
3.35 (2U) in x 17 in x 23 in
Unit dimensions with packaging
Height x Width x Depth
245 mm x 600 mm x 810 mm
9.7 in x 23.6 in x 31.9 in
The model and serial numbers are on a small label located on the rear panel.
4
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
SRT3000XLI/SRT3000RMXLI/SRT3000RMXLI-NC/SRT3000XLT/SRT3000RMXLT/SRT3000RMXLT-NC/
SRT3000XLW-IEC/SRT3000RMXLW-IEC model
The UPS is heavy. Follow all lifting guidelines.
Lifting guidelines
18 - 32 kg (40 - 70 lb)
32 - 55 kg (70 - 120 lb)
Unit weight batteries included, without packaging
31 kg (69 lb)
Unit weight batteries included, with packaging
Rack-Mount models: 40 kg (88 lb)
Tower models: 37 kg (81 lb)
Unit dimensions without packaging
Height x Width x Depth
Rack-Mount models:
85 (2U) mm x 432 mm x 611mm
3.35 (2U) in x 17 in x 24 in
Tower models:
85 (2U) mm x 432 mm x 636mm
3.35 (2U) in x 17 in x 25 in
Unit dimensions with packaging
Height x Width x Depth
245 mm x 600 mm x 870 mm
9.7 in x 23.6 in x 34.3 in
The model and serial numbers are on a small label located on the rear panel.
Battery
NOTICE
RISK OF EQUIPMENT DAMAGE
• Replace the battery at least every 5 years.
• Replace the battery immediately when the UPS indicates battery replacement is necessary.
Failure to follow these instructions can result in equipment damage
SRT2200 models
SRT3000 models
Battery type
Sealed, maintenance-free, Valve Regulated
Lead-Acid battery
Replacement battery module
APCRBC141
APCRBC152
This UPS has swappable battery modules.
Refer to the appropriate replacement battery user manual for
installation instructions.
Contact your dealer or go the APC by Schneider Electric web site,
www.apc.com for information on replacement batteries.
Number of battery modules
1 battery module
Voltage for each battery module
72 VDC
96 VDC
Total battery voltage for the UPS
72 VDC
96 VDC
Ah rating
5 Ah per battery module
XLBP cable length
500 mm (19.7 in)
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
5
Electrical
2200 VA / 1980 W
Building Circuit Breaker
(CB) Current Rating
16 A
3000 VA / 2700 W
20 A
Models
SRT2200XLI
Rating
SRT2200RMXLI
SRT2200RMXLI-NC
SRT3000XLI
SRT3000RMXLI
SRT3000RMXLI-NC
SRT3000XLT
20 A* / 2 pole
SRT3000RMXLT
SRT3000RMXLT-NC
SRT3000XLW-IEC
20 A IEC; 20 A UL* / 2 pole
SRT3000RMXLW-IEC
CAUTION
RISK OF FIRE, RISK OF DAMAGE TO EQUIPMENT OR PERSONNEL
* Connect the UPS models only to a circuit provided with recommended maximum branch circuit overcurrent protection in
accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.
Failure to follow these instructions can result in fire, equipment damage and minor or moderate injury.
Output
Output Frequency
50 Hz / 60 Hz
Nominal Output Voltage
SRT2200XLI/SRT2200RMXLI/SRT2200RMXLI-NC/SRT3000XLI/SRT3000RMXLI/
SRT3000RMXLI-NC: 220 V, 230 V, 240 V
SRT3000XLT/SRT3000RMXLT/SRT3000RMXLT-NC: 208 V, 240 V
SRT3000XLW-IEC/SRT3000RMXLW-IEC: 208V, 220V, 230V, 240V
Input
Input Frequency
40 Hz - 70 Hz
Nominal Input Voltage
SRT2200XLI/SRT2200RMXLI/SRT2200RMXLI-NC/SRT3000XLI/SRT3000RMXLI/
SRT3000RMXLI-NC: 220 V, 230 V, 240 V
SRT3000XLT/SRT3000RMXLT/SRT3000RMXLT-NC: 208 V, 240 V
SRT3000XLW-IEC/SRT3000RMXLW-IEC: 208V, 220V, 230V, 240V
Input current rating
SRT2200 models: 13 A
SRT3000 models: 16 A
6
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Front Panel Features
 Display interface panel
 UPS battery connectors
 Battery module
suo0860a
 Bezel
Rear Panel Features
Note: Refer to the table “Key to identify rear panel features” on page 8, that provides a key to the callout numbers for
the rear panel graphics depicted in this manual.
GROUP 1
10 AMP MAX
SRT2200XLI/SRT2200RMXLI/SRT3000XLI/SRT3000RMXLI
suo0882a
GROUP 1
10 AMP MAX
SRT2200RMXLI-NC/SRT3000RMXLI-NC
suo0882b
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
7
SRT3000XLT/SRT3000RMXLT
suo0883a
SRT3000RMXLT-NC
suo0883b
O VER LOA D
PR OTEC TO R
GROUP 1 MAX: 10 AMP IEC; 15 AMP UL
GROUP 2 MAX: 16 AMP IEC; 20 AMP UL
SRT3000XLW-IEC/SRT3000RMXLW-IEC
suo0884a
Key to identify rear panel features
8

SmartSlot

AC input
SRT3000XLT, SRT3000RMXLT, SRT3000RMXLT-NC models have factory installed input
power cable or
power cables.
hardwire input box

External battery
power and
communication
connector
The SmartSlot can be used to connect optional management accessories.
Use the external battery cable on the XLBP to connect the UPS and XLBP.
XLBPs provide extended runtime during power outages. The UPS will automatically
recognize up to 10 external battery packs.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U

Controllable
outlet group 1
Connect electronic devices to these outlets.

Chassis ground
screws
The UPS and XLBPs have ground screws for connecting the ground leads. Prior to
connecting a ground lead, disconnect the UPS from mains power.

Controllable
outlet group 2
Connect electronic devices to these outlets.

EPO terminal
The Emergency Power Off (EPO) terminal allows the user to connect the UPS to a central
EPO system.

Serial Com
The Serial Com port is used to communicate with the UPS.
Use only interface kits supplied or approved by APC by Schneider Electric. Any other
serial interface cable will be incompatible with the UPS connector.

USB port
The USB port is used to connect either a server for native operating system
communications, or for software to communicate with the UPS.
Note: Serial and USB communication should not be used simultaneously. Use either the
Serial Com or the USB port.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
9
Operation
Connect Equipment
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• Disconnect the mains input circuit breaker before installing or servicing the UPS or connected equipment.
• Disconnect internal and external batteries before installing or servicing the UPS or connected equipment.
• The UPS contains internal and external batteries that may present a shock hazard even when disconnected from the
mains.
• UPS AC hardwired and pluggable outlets may be energized by remote or automatic control at any time.
• Disconnect equipment from the UPS before servicing any equipment.
Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Note: The UPS batteries will charge to 90% capacity in the first three hours of normal operation. Do not expect full
battery runtime capability during this initial charge period.
1. Connect the internal battery module. See Installation manual for details.
2. Connect equipment to the outlets on the rear panel of the UPS.
Refer to “Controllable Outlet Groups” on page 19.
3. Connect the UPS to the building utility power.
Turn the UPS On/Off
The first time the UPS is turned on the Setup Wizard screen will run. Follow the prompts to configure UPS settings.
Refer to “Configuration” on page 14.
To turn on the UPS and all connected equipment, press the POWER ON/OFF button on the display panel. Follow the
prompts to either turn the UPS on immediately or after a delay, then press OK.
NOTE: When there is no input power and the UPS is off, the cold start feature can be used to turn on the UPS and
connected equipment using battery power.
To perform a cold start press the POWER ON/OFF button.
The display panel will illuminate and the POWER ON/OFF button will illuminate red.
To turn on the output power press the POWER ON/OFF button again. Select the prompt Turn ON with NO AC and press
OK.
To turn output power off, press the POWER ON/OFF button. Follow the prompts to either turn the UPS off immediately or
after a delay, then press OK.
NOTE: Once the UPS output power has been turned off and the AC input has been removed, the UPS will continue to
use the battery for internal power for 10 minutes. To remove power completely press the POWER ON /OFF button. Follow
the prompt to select Internal Power Off, then press OK.
10
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
UPS Display Interface
 POWER ON/OFF button
Button illumination indications:
-No illumination, the UPS and the output
power are off
-White illumination, the UPS and the
output power are on
-Red illumination, the UPS is on and the
output power is off
 Load icon
Disable/mute audible alarm icon
LOAD
Output 230.0 v
On-Line
1
2
 UPS status information
 Operation mode icons
 ESCAPE button
 OK button
su0870b
 UP/DOWN buttons
 Controllable outlet group status icons
 Battery status icons
UPS Display Interface operation
Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the ESC
button to return to the previous menu.
.
The icons on the LCD display interface screen may vary depending on the installed firmware versions and specific UPS
models.
LOAD
Load icon: The approximate load capacity percentage is indicated by the number of load bar
sections illuminated. Each bar represents 16% of the load capacity.
Mute icon: Indicates the audible alarm is disabled/mute.
UPS Status Information
The status information field provides key information on the status of the UPS.
The Standard menu will allow the user to select one of the five screens listed below. Use the UP/DOWN buttons to scroll
through the screens.
The Advanced menu will scroll through the five screens automatically.
• Input Voltage
• Output Voltage
• Output Frequency
• Load
• Runtime
In the case of a UPS event, status updates will be displayed defining the event or condition that has occurred.
The display screen illuminates amber to indicate a Message and red to indicate an Alert depending on the severity of the
event or condition.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
11
Operation Mode Icons
On-Line mode: The UPS is supplying conditioned mains power to connected equipment.
Bypass mode: The UPS is in Bypass mode and the connected equipment will receive mains
power as long as the input voltage and frequency are within the configured limits.
Green mode: When in Green mode mains power is sent directly to the load.
In the event of a mains power outage, there will be an interruption in power to the load of up to
10 ms while the UPS switches to On-Line or Battery mode.
When enabling Green mode consideration should be given to devices that may be sensitive to
power fluctuations.
Indicates a UPS alert that requires attention.
UPS Status Icon
Battery mode: The UPS is supplying battery power to connected equipment.
The UPS has detected an internal fault with the battery. Follow the instructions on the screen.
X
The UPS has detected a critical fault with the battery. The battery is at the end of its life and has
to be replaced.
Controllable Outlet Group Icons
Controllable Outlet Group Power Available: The number next to the icon identifies the
specific outlet groups that have available power.
Flashing icon indicates the outlet group is turning from OFF to ON with delay.
Controllable Outlet Group Power Not Available: The number next to the icon identifies
specific outlet groups that do not have available power.
Flashing icon indicates the outlet group is turning from ON to OFF with delay.
Battery Status Icons
Battery Charge Status: Indicates the battery charge status.
Battery Charge In Progress: Indicates the battery is charging.
12
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
LCD display interface angle adjustment
The angle of the LCD display interface can be adjusted for ease in viewing the displayed messages.
1. Remove the front bezel.
2. Locate the button on the bottom of the display interface panel.
3. Press the button and slide the bottom of the LCD display interface screen out. An audible click will be
heard when the screen reaches the maximum angle.
su
09
26
a
Menu overview
The UPS Display Interface has Standard and Advanced menu screens. The preference for Standard or Advanced
menu selections is made during initial installation and can be changed at any time through the Configuration
menu.
The Standard menus include the most commonly used options.
The Advanced menus provide additional options.
Note: Actual menu screens may differ by model and firmware version.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
13
UPS Menu Overview
Main Menu
Status
Control
Configuration
Test And Diagnostics
Log
About
Status Menu***
UPS
Battery
Accessory
Control Menu**
UPS
Bypass Control
Outlet Group 1*
Outlet Group 2*
Clear Alarms
UPS**
Efficiency
Output Power - Watts, VA,Load %
Output - Voltage, Frequency, Current
Energy Usage
Battery - Charge %, Runtime
Input - Voltage, Frequency
UPS Self Test
Runtime Test
Alert status - Site Wiring Fault
Battery
RBC Health
RBC Summary – Installed MMYY, Replace MMYY
Internal RBC’s, Battery Packs, External RBC’s
Charge %, Runtime
Temperature, Voltage
Internal Pack – Temperature
Internal Pack – Health
External Pack – Temperature
External Pack - Health
Accessory***
Smart Slot – Probe 1 Temperature
Smart Slot - Probe 1 Humidity
Smart Slot – Probe 2 Temperature
Smart Slot - Probe 2 Humidity
Config Menu
UPS
Battery
Outlets
Communication
Display
UPS**
Turn On Immediately
Turn On With Delay
Turn Off Immediately
Turn Off With Delay
Reboot Immediately
Reboot With Delay
Shutdown Immediately
Shutdown With Delay
Bypass Control**
Go into Bypass
Go out of Bypass
Outlet Group 1**
Turn On Immediately
Turn On With Delay
Turn Off Immediately
Turn Off With Delay
Reboot Immediately
Reboot With Delay
Shutdown Immediately
Shutdown With Delay
Outlet Group 2**
Turn On Immediately
Turn On With Delay
Turn Off Immediately
Turn Off With Delay
Reboot Immediately
Reboot With Delay
Shutdown Immediately
Shutdown With Delay
Clear Alarms**
No Alarms Exist
Test and Diagnostics Menu
UPS Self Test
Runtime Test
Alarm Test - Short
Alarm Test - Continuous
UPS**
Green Mode - Enable / Disable
Output Setting - Lower Volt, Upper Volt
Output Setting – Acceptable Frequency
Output Setting – Frequency Slew Rate
Bypass Settings - Lower Volt, Upper Volt
Bypass Settings – Frequency
Battery Settings – Low Runtime Warning
Self Test Schedule
Alert Setting - Site Wiring Fault
PDU model- Standard, SRT012
Default Setting
Energy Meter*
Battery
Install Date
Replace Notification
Replace Battery Alarm
Outlets
Main Outlet
Outlet Group 1
Outlet Group 2
Log
Event Log
About Menu***
UPS
Battery
Accessory
UPS***
UPS Hardware - Part No.
PDU Hardware
UPS Hardware - Serial No.
UPS Hardware - Manufacture Date
UPS Firmware – Revison
UPS – DSP Firmware
UPS – Comm Firmware
UPS Time
Battery
Part Number
RBC Summary - Installed MMYY, Replace MMYY
Battery – Firmware
Battery – Part No.
Accessory***
Smart Slot - Serial No.
Smart Slot - Part No.
Smart Slot - Firmware
Smart Slot - MAC Address
Smart Slot – IPv4 Address
Communication
SmartSlot- IP Address Mode, IPv4 Address
Modbus*- Enable / Disable, Address
Menus are subject to change depending on the installed firmware version
Display
Language
Audible Alarm – Disable, Enable
LCD Backlight – Always On, Auto Dim, Auto Off
LCD Settings- Color, Brightness, Contrast
Menu type - Standard / Advanced
Time***
* Available on the Advanced Menu Screens
** Options displayed will vary based on UPS state.
***Options displayed will vary based on connected accessories.
Configuration
UPS Settings
There are three ways to select UPS configuration options.
1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu screen select the
desired settings. Press OK after each UPS setting is selected.
Note: The UPS will not turn on until all of the settings have been configured.
2. Main Menu/Configuration/UPS/Default Setting. This screen allows the user to reset the UPS to factory
default settings. Press OK after the UPS setting is selected.
Refer to “Configuration” on page 14 and “UPS Menu Overview” .
3. Configure settings using an external interface, such as the Network Management Web interface.
Startup configuration
Function
Description
Select the language required for the display interface.
Language
Language options will vary by model and firmware version.
Francais
Italiano
Setup Wizard
Options:
• English
• Francais
• Italiano
• Deutsch
• Espanol
• Portugues
• Russian
Select the output voltage.
Voltage AC Setting
230 VAC
240 VAC
Setup Wizard
Options will vary by model.
Options:
• 208 Vac
• 220 Vac
• 230 Vac
• 240 Vac
The Standard menu options are the most commonly used options.
Menu Type
The Advanced menu options will be used by IT professionals who need
detailed configuration and reporting information.
Advanced
Setup Wizard
14
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
General settings
Configure these settings at any time, using the display interface, or the Network Management Web Interface.
Parameters
Config
Menu
UPS
Green Mode
Default Value
Disabled
Options
Disable
Description
Disable or enable Green mode operation
Enable
AC Setting
NA
(see description)
XLW models: 208 V,
220 V, 230 V, 240 V
Set the output voltage for the UPS. This setting can
only be changed when the UPS output is off.
XLI models: 220 V,
230 V, 240 V
These settings may vary depending on the UPS
model.
XLT models: 208 V,
240 V
Default Value:
The value selected by the user during initial
startup. Reset to factory default does not
change the selected value.
Output
Lower
Acceptable
Voltage
184 V for 208 V output
198 V for 220 V output
207 V for 230 V output
216 V for 240 V output
208 V - 169 to 184 V
220 V - 186 to 198 V
230 V - 195 to 207 V
240 V - 204 to 216 V
Output
Upper
Acceptable
Voltage
220 V for 208 V output
242 V for 220 V output
253 V for 230 V output
264 V for 240 V output
208 V - 220 to 235 V
220 V - 242 to 253 V
230 V - 253 to 265 V
240V - 264 to 270 V
If the output voltage goes outside the acceptable
range the UPS will switch from Green mode to
On-Line mode or to Battery mode.
Output
Frequency
Auto 50/60 ± 3Hz
Auto 50/60 ± 3 Hz
50 ± 0.1 Hz
50 ± 3.0 Hz
60 ± 0.1 Hz
60 ± 3.0 Hz
Set the output frequency for the UPS.
Output
Frequency
Slew Rate
1 Hz/Sec
0.5 Hz/Sec
1 Hz/Sec
2 Hz/Sec
4 Hz/Sec
Select the rate of change for output frequency in
Hertz per second.
Bypass
Lower
Acceptable
Voltage
160 V
208 V - 160 to 184 V
220 V - 160 to 198 V
230 V - 160 to 207 V
240V - 160 to 216 V
Bypass
Upper
Acceptable
Voltage
250 V for 208 V output
255 V for 220 V output
265 V for 230 V output
270 V for 240 V output
208 V - 220 to 250 V
220 V - 242 to 264 V
230 V - 253 to 270 V
240 V - 264 to 270 V
Bypass
Setting
Acceptable
Frequency
Wider Frequency
47 - 63 Hz
• Wider Frequency
47 - 63 Hz
• Use Output
Frequency Setting
The setting Wider Frequency, enables Bypass
mode operation for an input frequency range of
47-63 Hz.
Low
Runtime
Alert
150 seconds
0 to 1800 seconds
The UPS will emit an audible alarm when the
remaining runtime has reached this threshold.
Self Test
Schedule
Startup + every 14
days since last test
• Never
• Startup
• Startup + 7 days
• Startup + 14 days
This is the interval at which the UPS will execute a
Self Test.
If the UPS input voltage is between the lower
acceptable voltage and the higher acceptable
voltage, the UPS will operate in Green mode when
enabled.
If the UPS input voltage is between the lower
acceptable voltage and the higher acceptable
voltage, the UPS can enter Bypass mode when
enabled.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
15
Parameters
Config
Menu
UPS
Site Wiring
Fault
Default Value
Disable
(For XLI and
XLW models
only)
Options
• Disable
• User Can
Acknowledge
• Enable
Description
Allows the user to configure the behavior of
the UPS in response to the site wiring fault
alert which is generated due to wrong input AC
mains connection with input phase and neutral
reversed.
Disable: The UPS never indicates site wiring
fault to the user.
User Can Acknowledge: UPS alerts the user
about site wiring fault, when detected. The
alert is active till the user acknowledges it by
pressing OK.
Enable: UPS alerts the user about site wiring
fault, when detected. The alert cannot be reset
until the site wiring fault is corrected.
PDU Model
Standard
SRT011 and SRT012 Select the PDU model installed in the UPS for
for XLT and XLW
proper operation of the PDU.
models
See the user documentation for the PDU
SRT012 for XLI
models SRT011and SRT012 for details.
models
Default
Setting
No
Yes/No
Allows the user to restore the UPS factory default
settings.
Reset Energy No
Meter
Yes/No
The Energy Meter stores information on UPS output
energy usage.
The Reset feature allows the user to reset the
Energy Meter to 0 kWh.
Config Install Date
Menu
Battery
Battery Installation
Date
Replacement 180 days
Notification
Time
Month-Year
Enter the installation date of the RBCs.
0-360 days
To set the Near End of Life audible alarm, select
the number of days before the estimated battery end
of life.
When this date is reached the UPS will emit an
audible alarm and a message will appear on the
display interface screen.
Example: Using the default value, the Near End of
Life audible alarm will occur 180 days before the
estimated end of life date.
Replacement 14 days
Battery
Alarm Time
16
0-180 days
The Near End of Life audible alarm can be
muted. Enter the number of days between the
time a Near End of Life audible alarm is
acknowledged and the next Near End of Life
audible alarm occurs.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Parameters
Config Language
Menu
Display
Default Value
English
Options
Description
English
Francais
Italiano
Deutsch
Espanol
Portugues
Russian
Select the language required for the display
interface.
Language options will vary by model and firmware
version.
Audible
alarm
Enable
• Disable
• Enable
When audible alarms are disabled, the UPS will
never emit an audible alarm.
LCD
Back Light
Auto Dim
Always On
Auto Dim
Auto Off
To conserve energy, the LCD back light illumination
dims or turns off when no events are active.
Full display interface illumination returns when the
UPS changes status as a result of an event or when
any button on the display interface is pressed.
LCD Setting
Optimal Values
Color
Brightness
Contrast
Adjust the brightness and contrast individually for
each LCD back light color.
Menu Type
User Choice
Standard
Advanced
The Standard menus include the most commonly
used options.
The Advanced menu options include all parameters.
UTC time
DD-MMM-YYYY
HH:MM:SS am/pm
Scroll through the fields to set the time.
0 seconds
0-1800 seconds
Select the amount of time the controllable outlet
groups will wait between receiving the command to
turn on and actual startup.
Power Off
Delay
90 seconds
0-32767 seconds
Select the amount of time the controllable outlet
groups will wait between receiving the command to
shutdown and actual shutdown.
Reboot
Duration
8 seconds
4-300 seconds
Select the amount of time the controllable outlet
groups will remain off before the UPS will restart.
Minimum
Return
Runtime
0 seconds
0-32767 seconds
Select the amount of battery runtime that must be
available before the controllable outlet groups will
turn on using battery power, after a shutdown.
Loadshed
Time On
Battery
Disable
Disable
Enable
To conserve battery power the UPS can disconnect
power from controllable outlet groups not in use.
Loadshed
Time On
Battery
5 seconds
Time
Config Power On
Menu Delay
Outlets
To configure the disconnect delay time for this
feature use the Loadshed Time On Battery setting.
Loadshed On Disable
Runtime
5-32767 seconds
Select the amount of time the controllable outlet
groups will be allowed to function on battery power
before shutdown.
Disable
Enable
To conserve battery power the UPS can disconnect
power from controllable outlet groups when the
Loadshed Runtime threshold is reached.
Loadshed
Runtime
0 seconds
0-3600 seconds
When the selected runtime threshold is reached the
UPS will shutdown the controllable outlet groups.
Loadshed
Overload
Disable
Disable
Enable
To conserve energy in the event of an overload
condition greater than 105% output, the controllable
outlet groups will immediately turn off. The
controllable outlet groups will only turn on again
with a manual restart command once the overload
condition has been corrected.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
17
Parameters
Config IP Address
Menu Mode
Network
Manage IP Address
(for NC
models
only)
18
Default Value
Options
Description
Manual, DHCP,
BOOTP
Program IP, Subnet,
Gateway
Refer to the Network Management Utility CD.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Controllable Outlet Groups
Controllable Outlet Groups provide battery backup power to connected equipment.
Overview
The controllable outlet groups can be configured using the Advanced menu options.
Refer to “General settings” on page 15.
The controllable outlet groups can be configured to independently turn off, turn on, shutdown, switch to sleep
mode, and reboot connected equipment.
• Turn Off: Disconnect output power to connected equipment either immediately using the Turn Off
Immediately feature or after a configured delay using the Turn Off With Delay feature.
NOTE: Controllable outlet groups can be turned on only using the Turn On feature.
• Turn On: Connect output power to connected equipment either immediately using the Turn On
Immediately feature or after a configured delay using the Turn On With Delay feature.
• Shutdown: Disconnects the power to connected equipment either immediately or after a configured delay.
Equipment reconnects after a configured delay when mains power becomes available and other configured
conditions are met.
Each controllable outlet group can be configured separately to allow power sequencing for equipment
connected to any controllable outlet group.
• Reboot: Disconnect the power to connected equipment either immediately or after a configured delay.
Reconnect equipment after a configured delay when either mains or battery power becomes available and
other configured conditions are met.
Each controllable outlet group can be configured separately to allow power sequencing for loads connected
to any controllable outlet group.
• Sleep: This mode is a reboot with an extended duration where a outlet(s) remain turned off.
Disconnect the power to connected equipment either immediately or after a configured delay. Reconnect
equipment after a configured delay when either mains or battery power becomes available and other
configured conditions are met.
Each controllable outlet group can be configured separately to allow power sequencing for equipment
connected to any controllable outlet group.
To configure Sleep mode use an external interface, such as the Network Management Web interface.
• Automatically turn off or shutdown when certain conditions occur, based on user configurations set using
the Config Menu Outlets menus. Refer to “Configuration” on page 14
Connect controllable outlet groups
• Connect critical equipment to one controllable outlet group.
• Connect peripheral equipment to the other controllable outlet groups.
– To conserve battery runtime during a power outage, nonessential equipment can be configured to shut
down. Use Loadshed Time on Battery Enable/Disable and Loadshed Time on Battery Setting
defined in the General Settings section. Refer to “General settings” on page 15.
– If equipment has dependent peripherals that must restart or shut down in a specific sequence, such as an
ethernet switch that must restart before a connected server can be restarted, connect the devices to
different outlet groups. Each controllable outlet group can be configured independently of the other
groups.
• Use the Configuration menus to configure how the controllable outlet groups will react in the event of a
power outage.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
19
Emergency Power Off
Overview
The Emergency Power Off (EPO) option is a feature that will immediately disconnect all connected equipment
from mains power. The UPS will immediately shut down and will not switch to battery power.
Connect each UPS to the EPO switch. If multiple units are to be controlled with an EPO switch, each UPS must be
connected separately to the EPO switch.
The UPS must be restarted for power to return to connected equipment. Press the ON /OFF button on the front panel
of the UPS.
CAUTION
RISK OF DAMAGE TO EQUIPMENT OR PERSONNEL
• Adhere to all national and local electrical codes.
• Wiring must be performed by a qualified electrician.
• Always connect the UPS to a grounded outlet.
Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Normally open contacts
1. If the EPO switch or relay contacts are normally open, insert the wires from the
switch or contacts at pins 1 and 2 of the EPO terminal block. Use 16-28 AWG
wire.
2. Secure the wires by tightening the screws.
If the contacts are closed, the UPS will turn OFF and power will be removed from the load.
Normally closed contacts
1. If the EPO switch or relay contacts are normally closed, insert the wires from the
switch or contacts at pins 2 and 3 of the EPO terminal block. Use 16-28 AWG
wire.
2. Insert a wire jumper between pins 1 and 2. Secure the wires by tightening the
three screws at positions 1, 2, and 3.
If the contacts are opened, the UPS will turn OFF and power will be removed from the load.
Note: Pin 1 is the power source for the EPO circuit, it provides a few milliampere of 24 V power.
If the normally closed (NC) EPO configuration is used, the EPO switch or relay should be rated for “dry” circuit
applications, the rating should be for low voltage and low current applications. This normally implies the contacts
are gold plated.
The EPO interface is a Safety Extra Low Voltage (SELV) circuit. Connect the EPO interface only to other SELV
circuits. The EPO interface monitors circuits that have no determined voltage potential. SELV circuits are
controlled by a switch or relay properly isolated from mains power. To avoid damage to the UPS, do not connect
the EPO interface to any circuit other than a SELV circuit.
Use one of the following cable types to connect the UPS to the EPO switch.
• CL2: Class 2 cable for general use.
• CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.
• CL2R: Riser cable for use in a vertical run in a floor to floor shaft.
• CLEX: Limited use cable for use in dwellings and for use in raceways.
• Installation in Canada: Use only CSA certified, type ELC, (extra low voltage control cable).
• Installation in countries other than Canada and the USA: Use standard low voltage cable in accordance with national
and local regulations.
20
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Network Management Interface
(For NC models only)
Introduction
The UPS has a network port and console port that can be used to access the Network Management Interface. Refer
to the Network Management Card utility CD supplied with this product.
IP Address Configuration
The default TCP/IP configuration setting DHCP, assumes that a properly configured DHCP server is available to
provide TCP/IP settings to the Network Management Interface.
If the Network Management Interface obtains an IPv4 address from a DHCP server, use the display interface
menus About/Accessory, to see the address.
To setup a static IPv4 address use the display interface Config menu. Set the IP address Subnet Mask and Gateway
from the Config menu.
See the User’s Guide on the Network Management Card Utility CD for user information about the Network
Management Interface and for setup instructions.
Related Documents
The Network Management Card Utility CD contains the following documentation:
• UPS Network Management Card 2 User’s Guide
• Network Management Card Upgrade Utilities
• Security Handbook
• PowerNet Management Information Base (MIB) Reference Guide
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
21
Smart Battery Management
Definitions
• Battery Module: A string of battery cells arranged to produce a battery assembly with a connector.
• Replaceable Battery Cartridge (RBC): An APC battery cartridge consisting of one battery module.
Replacement RBCs can be ordered from the APC by Schneider Electric web site, www.apc.com.
• Smart External Battery Pack (XLBP): An enclosure that contains RBC(s) and battery management
electronics.
• User Interface (UI): Any interface by which a user can interact with the system. This may include a UPS
display interface, a network management interface or PowerChute™ Network Shutdown software.
NOTE: Do not use a battery that is not APC approved.
The system will not detect the presence of a non APC approved battery and may adversely affect the
operation of the system.
Use of a non APC approved battery will void the manufacturer warranty.
Features
Smart Battery Management provides the following features:
• Monitors and informs the user of the health of each RBC.
• Monitors and shows on the UPS Display Interface screen, the date for the end of useful life for each RBC.
• The UPS emits an audible alarm and shows a message on the UPS Display Interface screen to indicate the
estimated battery end of life. On the UPS Display Interface screen the user can set the number of days
before the audible alarm is heard and the message appears on the UPS Display Interface screen.
• Automatically detects the addition or removal of XLBPs and RBCs.
• Monitors the internal temperature of each XLBP and automatically adjusts the battery charging.
Maintenance
• RBC maintenance: The APC RBC uses sealed, maintenance-free, Valve Regulated Lead-Acid batteries
and does not require maintenance.
• Runtime Test (Calibration): This should be performed anytime the steady state load is changed
significantly, for example a new server is added to or removed from the UPS load.
• Battery health monitoring: The battery energy output and voltage are monitored to assess the health of the
installed batteries when the UPS is operating on battery.
Battery health monitoring is done during a UPS Self Test, a Runtime Calibration Test, and when the UPS
is operating on battery power.
The UPS can be configured to perform periodic, automatic Self Tests.
End of useful life
• Near end of life notification: A message will appear on the UPS display interface screen when each RBC
is approaching the end of its useful life. For configuration details refer to Replacement Notification Time
and Replacement Battery Alarm Time.
The estimated replacement date for each RBC is available through the UI.
• Needs replacement notification: The UPS display interface screen shows when RBC replacement is
required. The RBC must be replaced as soon as possible.
When an RBC requires replacement, the UPS display interface may recommend that additional RBCs be
replaced if they will soon reach the end of their useful life.
CAUTION: Continued operation after end of useful life notification may cause damage to the batteries.
• Recycling: Remove the RBC from the XLBP. Recycle the RBC. Do not disassemble an RBC.
22
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Replace the RBC in a UPS
An RBC should only be disconnected or removed from the UPS temporarily as part of the battery
replacement procedure.
• Disconnect the connected battery module in the UPS. Slide the RBC out of the UPS.
• Slide the new RBC into the UPS and connect the battery module to the UPS.
• Securely connect the battery module. Press the battery connector into the UPS until it is firmly connected.
A battery that is not properly connected will cause erratic UPS operation, abnormal alert messages and
connected equipment may not receive battery power during power outages.
• After installing the RBC, the UPS display interface may prompt the user to verify the status of the replaced
battery module. If the battery module is new, respond YES. If the battery module is not new, respond NO.
Recommended actions after installing new RBC
• Verify that the UPS is connected to input power and the output power is turned on. See “Operation” on
page 10 for instructions.
• Perform a UPS Self Test.
• Verify on the UPS display interface that the installation dates for the replaced RBC is set to the current date.
The installation dates can be changed manually on the UPS display interface.
For configuration details refer to Battery Install Date in the “General settings” on page 15 of this manual.
• Allow the system to charge for 24 hours to ensure full runtime capability.
XLBP installation and replacement
Refer to the External Battery Pack Installation Guide for installation and replacement instructions.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
23
Troubleshooting
Use the table below to solve minor installation and operation problems.
Refer to the APC by Schneider Electric web site, www.apc.com for assistance with complex UPS problems.
The UPS features firmware that can be upgraded.
Go to the APC by Schneider Electric web site, www.apc.com/Support, or contact your local Customer Care
Center for more information.
Problem and Possible Cause
Solution
UPS is not turning on or there is no output
The UPS is not connected to mains
power.
Be sure the power cable is securely connected to the mains power supply.
The UPS display interface screen shows
very low or no mains power.
Check the mains power supply to verify acceptable power quality.
There is an internal UPS alert or
message.
The UPS Display Interface screen will show a message to identify the alert or
message and corrective action.
UPS emits an audible alarm
Normal UPS operation when running on
battery power.
The UPS is operating on battery power.
Refer to the status of the UPS as shown on the UPS Display Interface screen.
Press any key to mute all audible alarms.
The UPS emits an audible alarm and has The UPS has detected a fault.
a red or amber back light on the UPS
Refer to the display interface screen for information.
Display Interface screen.
UPS does not provide expected backup time
The UPS batteries are weak due to a
recent power outage or they are near the
end of service life.
Charge the batteries. Batteries require recharging after extended outages and
wear out faster when put into service often or when operated at elevated
temperatures. If the batteries are near the end of service life, consider
replacing the batteries even if the Replace Battery message is not displayed.
The UPS is experiencing an overload
condition.
The connected equipment exceeds the specified maximum load. Refer to the
APC by Schneider Electric web site, www.apc.com for product
specifications.
The UPS will emit a sustained audible alarm until the overload condition is
corrected.
Disconnect nonessential equipment from the UPS to correct the overload
condition.
24
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Problem and Possible Cause
Solution
UPS operates on battery power while connected to mains power
The input circuit breaker has tripped.
Reduce the load on the UPS. Disconnect nonessential equipment and reset
the circuit breaker. Check the circuit breaker rating for the connected
equipment.
There is very high, very low, or distorted Navigate to the UPS Display Interface screen that shows input voltage.
input line voltage.
Verify that the input voltage is within specified operating limits.
If no input voltage is indicated on the UPS Display Interface screen, contact
Customer Support through the APC by Schneider Electric web site,
www.apc.com.
The UPS Display Interface screen shows The UPS has been configured to operate for a specified period of runtime.
the message Waiting for Minimum
The setting can be changed through the Config/UPS menus.
Runtime.
UPS Display Interface Status screen shows Overload and the UPS emits a sustained audible alarm
The UPS is experiencing an overload
condition.
The connected equipment exceeds the maximum load rating for the UPS.
The UPS will emit a sustained audible alarm until the overload condition is
corrected.
Disconnect nonessential equipment from the UPS to correct the overload
condition.
UPS Display Interface Status screen shows UPS is operating in Bypass mode
The UPS received a command to operate No action is required.
in Bypass mode
The UPS has automatically switched to
Bypass mode due to an internal UPS
alert or message.
The UPS Display Interface screen will show a message to identify the alert or
detected error and corrective action.
UPS Display Interface is red or amber and shows an alert or message
The UPS emits a sustained audible alarm
The UPS has detected a problem during
normal operation.
Follow the instructions on the UPS Display Interface screen.
Press any key to mute all audible alarms.
The UPS Display Interface screen shows Be sure the battery cables are securely connected.
the message Disconnected Battery.
Perform a UPS Self Test to be sure the UPS detects all connected batteries.
To perform a UPS Self Test use the UPS Display Interface menu option Test
and Diagnostics.
The UPS Display Interface screen shows Replace all of the batteries. Contact APC by Schneider Electric customer
the message Replace Battery.
support.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
25
Problem and Possible Cause
Solution
The UPS display turns red or amber, displays an alert message, and emits a sustained audible alarm.
Red illumination indicates a UPS alarm that requires immediate attention.
Amber illumination indicates a UPS alarm that requires attention.
There is an internal UPS alert or
message.
Do not attempt to use the UPS. Turn the UPS off and have it serviced
immediately.
1/1
Power Sys Error - 00100
Contact Customer Support
Output Off
1
2
The UPS is experiencing an overload
condition.
Reduce the load on the UPS. Disconnect nonessential equipment.
1/1
Output Overload
Bypass
1
2
The UPS has detected a Site Wiring
Fault.
Correct the building site wiring fault or ignore this message. See Config
Menu UPS in “General settings” on page 15.
1/1
Site Wiring Fault
Press OK to Clear Alarm
Online Green
1
2
The Replace Battery alert is displayed
The battery has a weak charge.
Allow the battery to recharge for at least four hours. Then, perform a
UPS Self Test. If the problem persists after recharging, replace the battery.
The replacement battery is not properly
connected.
Be sure the battery cable is securely connected.
26
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Transport
1. Shut down and disconnect all connected equipment.
2. Disconnect the unit from mains power.
3. Disconnect all internal and external batteries (if applicable).
4. Follow the shipping instructions outlined in the Service section of this manual.
Service
If the unit requires service, do not return it to the dealer. Follow these steps:
1. Review the Troubleshooting section of the manual to eliminate common problems.
2. If the problem persists, contact APC by Schneider Electric Customer Support through the APC by
Schneider Electric web site, www.apc.com.
a. Note the model number and serial number and the date of purchase. The model and serial numbers
are located on the rear panel of the unit and are available through the LCD display on select models.
b. Call Customer Support. A technician will attempt to solve the problem over the phone. If this is not
possible, the technician will issue a Returned Material Authorization Number (RMA#).
c. If the unit is under warranty, the repairs are free.
d. Service procedures and returns may vary internationally. For country specific instructions
refer to the APC by Schneider Electric web site, www.apc.com.
3. Pack the unit properly to avoid damage in transit. Never use foam beads for packaging.
Damage sustained in transit is not covered under warranty.
Note: Before shipping, always disconnect battery modules in a UPS or external battery pack.
The disconnected internal batteries may remain inside the UPS or external battery pack.
4. Write the RMA# provided by Customer Support on the outside of the package.
5. Return the unit by insured, prepaid carrier to the address provided by Customer Support.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
27
Limited Factory Warranty
Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in materials and
workmanship for a period of three (3) years excluding the batteries, which are warranted for two (2) years from the
date of purchase. The SEIT obligation under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. Repair or replacement of a defective product or part thereof does not extend
the original warranty period.
This warranty applies only to the original purchaser who must have properly registered the product within 10 days
of purchase. Products may be registered online at warranty.apc.com.
SEIT shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the
product does not exist or was caused by end user or any third person misuse, negligence, improper installation,
testing, operation or use of the product contrary to SEIT recommendations of specifications. Further, SEIT shall not
be liable for defects resulting from: 1) unauthorized attempts to repair or modify the product, 2) incorrect or
inadequate electrical voltage or connection, 3) inappropriate on site operation conditions, 4) Acts of God, 5)
exposure to the elements, or 6) theft. In no event shall SEIT have any liability under this warranty for any product
where the serial number has been altered, defaced, or removed.
EXCEPT AS SET FORTH ABOVE, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY
OPERATION OF LAW OR OTHERWISE, APPLICABLE TO PRODUCTS SOLD, SERVICED OR
FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH.
SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND
FITNESS FOR A PARTICULAR PURPOSE.
SEIT EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND
NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SEIT RENDERING OF TECHNICAL OR
OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS.
THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE
SEIT’S SOLE LIABILITY AND PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH
WARRANTIES. SEIT WARRANTIES EXTEND ONLY TO ORIGINAL PURCHASER AND ARE NOT
EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL SEIT, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE
LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,
ARISING OUT OF THE USE, SERVICE OR INSTALLATION OF THE PRODUCTS, WHETHER SUCH
DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR
STRICT LIABILITY OR WHETHER SEIT HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY
OF SUCH DAMAGES. SPECIFICALLY, SEIT IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST
PROFITS OR REVENUE, WHETHER DIRECT OR INDIRECT, LOSS OF EQUIPMENT, LOSS OF USE
OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY
THIRD PARTIES, OR OTHERWISE.
NOTHING IN THIS LIMITED WARRANTY SHALL SEEK TO EXCLUDE OR LIMIT SEIT LIABILITY
FOR DEATH OR PERSONAL INJURY RESULTING FROM ITS NEGLIGENCE OR ITS
FRAUDULENT MISREPRESENTATION OF TO THE EXTENT THAT IT CANNOT BE EXCLUDED
OR LIMITED BY APPLICABLE LAW.
To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from
customer support. Customers with warranty claims issues may access the SEIT worldwide customer support
network through the APC by Schneider Electric web site: www.apc.com. Select your country from the country
selection drop down menu. Open the Support tab at the top of the web page to obtain information for customer
support in your region. Products must be returned with transportation charges prepaid and must be accompanied by
a brief description of the problem encountered and proof of date and place of purchase.
28
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
APC by Schneider Electric
Worldwide Customer Support
Customer support for this or any other APC by Schneider Electric product is available at no charge in any of
the following ways:
• Visit the APC by Schneider Electric web site to access documents in the APC by Schneider Electric
Knowledge Base and to submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC by Schneider Electric web sites for specific countries, each of which
provides customer support information.
– www.apc.com/support/
Global support searching APC by Schneider Electric Knowledge Base and using e-support.
• Contact the APC by Schneider Electric Customer Support Center by telephone or e-mail.
– Local, country specific centers: go to www.apc.com/support/contact for contact information.
– For information on how to obtain local customer support, contact the APC by Schneider Electric
representative or other distributor from whom you purchased your APC by Schneider Electric
product.
© 2016 APC by Schneider Electric. APC, the APC logo, and Smart-UPS are owned by Schneider Electric
Industries S.A.S. or their affiliated companies. All other trademarks are property of their respective owners.
EN 990-5269B
5/2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising