Important safeguards
I m p o r t a n t s a f e g u a rd s
• Use this appliance only as described in this instruction manual.
As with any electrical appliance, the instructions aim to cover as many situations as possible.
Caution and common sense should be used when operating and installing this air conditioner.
• This appliance has been manufactured to cool and dehumidify domestic environments and
must not be used for other purposes.
• It is dangerous to alter or modify the unit's characteristics in any way.
• The appliance must be installed in accordance with the relevant national legislation.
• Should repairs be necessary, contact the nearest authorized Repair Service Center. Unauthorized servicing can be dangerous.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• In the case that the power cord becomes damaged, this must be repaired only by specialized personnel authorized by the manufacturer in order to protect against fire.
• Always ensure the appliance is plugged into a grounded 3-prong outlet. If you have any doubts
check with a qualified electrician.
• We strongly discourage the use of an extension cord due to potential safety hazards.
• Before cleaning or maintenance operations, always unplug the unit from the outlet.
• Do not pull on or place strain on the power cord when moving the appliance.
• The appliance should not be installed where the atmosphere may contain combustible gases,
oil or sulphur, or near heat sources.
• Do not rest hot or heavy objects on the appliance.
• Clean the filters at least once a week.
• Avoid using heaters near the unit.
• The unit should be transported in a vertical position. If this is not possible secure the unit at an
angle, do not lie it horizontally.
• Before transporting the unit, drain the unit. After transportation, wait at least 6 hours before switching the unit on.
• The packaging materials can be recycled. You are therefore recommended to place them in
the special containers for differentiated waste collection.
• This appliance is fitted with a special safety device. When the compressor switches off, this
device prevents it from switching on again for at least 3 minutes.
• WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD ONLY
DESCRIPTION
1 air outlet grille
2
3
4
5
6
7
8
9
10
11
4
control panel
castors
handles
filter
evaporator air intake grille
air exhaust hose housing
condenser air intake grille
power cable
drainage hose with black cap
wall flange
12
13
14
15
16
17
18
19
20
21
air exhaust hose
hose adaptor (2 pieces)
accessory for wall mounting
window bracket grille
window bracket cap
window bracket
additional window bracket
6 screws
window outlet
remote control
Pre p a r i n g f o r u s e
ELECTRICAL CONNECTIONS
Before plugging the appliance into the mains socket, check that:
• The outlet’s power supply corresponds to the value indicated on the rating label on the back
of the appliance;
• The outlet and electrical circuit are adequate for the appliance;
• The outlet is a 3-hole grounded outlet . If this is not the case, you must choose another outlet.
Failure to follow these important safety instructions absolves the manufacturer of all liability.
The power cable must be replaced by a qualified professional only.
The instructions below will enable you to prepare your air conditioner for operation as efficiently
as possible. Before use, make sure the air intake and outlet grilles are unobstructed.
AIR-CONDITIONING WITHOUT INSTALLATION
• Open the window.
Just a few simple steps and your comfort is
ensured with your air conditioner:
• Place the window bracket 17 in the window, extending it to fit the width of the
window (fig. C).
• Screw one hose adaptor
end 12 .
13 to the hose’s
C
D
• Fit the other hose adaptor 13 in the air
exhaust hose housing 7 at the back of
the appliance (see fig. A).
• Screw the other end of the hose to the
adaptor, that was already fitted to the appliance (see fig. A).
• Once the bracket is extended, it can be
locked into his width by tightening the last
two screws provided.
• Close the window (fig. D).
• Place the air conditioner near the window. Insert the assembled exhaust hose
12 into the window bracket grille 17 (fig.
E). Make sure the air exhaust hose is unobstructed.
• When not used, the window bracket can
be closed off with the cap 16 provided.
A
Sash window
• Attach the window bracket grille 15 to
the window bracket 17 with the screws
provided 19
using a screwdriver, not
included (fig. B).
B
E
• If you have a very large window, in order
to cover your window aperture, use the
additional window bracket without holes
extending it to the desired dimension,
then fix the bracket by using the pins provided. When extracting the window
bracket and joining the two pieces pay
attention you do not cover the hole or
holes (depending on the model).
Keep the air hoses as short and free of
curves as possible to avoid constrictions.
5
GB
Pre p a r i n g f o r u s e
French window
134
5,25 in.
• Attach the window outlet 20 to the air
exhaust hose as shown in fig. F.
2
1
in the window
pane
F
I
• Open the French window slightly and position the outlet 20 as shown in figure G
G
Keep the air hoses as short and free of
curves as possible to avoid constrictions.
in the wooden
kickboard of a
French window
in the wall: you are
recommended to
insulate the section
of wall using suitable insulation.
• Fit the wall flange 11 into the hole.
• Screw the hose 12 to the adaptor 13 ,
that was already fitted to the appliance (fig.
A).
• Remove the
L
plastic end
of the hose
1
12
b y
unscrewing it
and in its
2
place screw
the
wall
mounting
accessory
14 (fig. L).
• Fit the end of the hose 12 to the wall
flange 11 as shown in fig. M.
SEMI-PERMANENT INSTALLATION
If required, your appliance can also be
installed semi-permanently (Fig. H).
MAX100 cm
MAX 39 inches
MIN 35 cm
MAX 14 inches
M
30 cm
12 inches
H
When the hose 12 is not fitted, the hole can
30 cm
12 inches
Proceed as follows:
• Drill a hole (ø134mm / 5,27 in.) in an outside wall or through a window pane.
Respect the height and dimensions of the
hole given in figures M and I.
6
be closed with the flange cap
11 .
NOTE: When installing the air conditioner
semi-permanently, you should leave a door
slightly open (as little as 1 cm) to guarantee
correct ventilation.
C o n t ro l p a n e l
THE CONTROL PANEL
S
O
Q
P
N
A
B
I
H
G
T
GB
L
M
C
R
D
E
F
DESCRIPTION OF THE CONTROL PANEL
A ON/OFF button
B MODE selection button
Air conditioning, dehumidifying, fan.
C Fan speed selection button (MAX/MED/MIN)
D Timer button
E Programmed operation increase temperature/time button
F Programmed operation decrease temperature/time button
G Display Displays the temperature values set and the programmed operating time
H Timer in operation indicator light
I/L/M Fan speed lights
N Fan mode light
O Air-conditioning mode light
P Dehumidifying mode light
Q Alarm light
R Remote control receiver
S Light: the inner temperature is shown on the display
T Light: the outdoor temperature is shown on the display
Never turn the air conditioner off by unplugging from the outlet. Always press the
button, then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation.
7
O p e ra t i o n
TURNING THE APPLIANCE ON
Before plugging the appliance check the black cap on the
back of the unit is correctly inserted in the drainage hose
10 .
Plug into an outlet. Two lines appear on the display indicating
that the appliance is in stand-by.
Press the ON/STAND-BY button (A). When turned on, the air conditioner starts operating in the same mode as when it was turned
off.
Press the MODE button (B) until the light corresponding to the
desired mode lights up:
Light (O): air-conditioning mode
Light (P): dehumidifying mode
Light (N): fan mode
AIR CONDITIONING MODE
Ideal for hot muggy weather when you need to cool and dehumidify the room.
The display shows the inner temperature: the light (S) turns on.
To modify the set temperature, push the (E) or (F) button to reach
the desired temperature. The (T) light turns on and the (S) light
turns off. (To change from °F to °C or viceversa, press for few seconds both button E and F).
After 15 seconds, the inner temperature is shown on the display.
The (S) light turns on.
You can adjust the temperature only in air conditioning mode.
Then select the fan speed by pressing the FAN button (C) until the
light corresponding to the required fan speed lights up:
MAX: the air conditioner operates at maximum to achieve the
target temperature as rapidly as possible
MED:
reduces noise levels while maintaining a comfortable
temperature
MIN:
for silent operation
The most suitable temperature for the room during the summer
varies from 75°F to 81°F (24 to 27°C). You are recommended,
however, not to set a temperature much below the outdoor
temperature
8
O p e ra t i o n
FAN MODE
Adjust fan speed by pressing the FAN button (C) as described for the air-conditioning mode.
Remember that the higher the speed, the more air is filtered. If you select "MIN" speed, less air is
filtered but the appliance is also less noisy.
GB
DEHUMIDIFYING MODE
Ideal for reducing the humidity in a room without lowering or raising the temperature (spring or
autumn, damp rooms, rainy spells, etc).
When the dehumidifying mode is selected, the light (P) comes on.
At the same time, the "MIN" fan speed light (M) comes on. In this mode, other speeds cannot be
selected.
PROGRAMMING THE TIMER
The timer can be used to delay appliance start up or shut down. This avoids wasting electricity by
optimising operating periods.
How to programme delayed start up
• Plug the appliance into a mains socket and press the ON/OFF button (A), then select the
required operating mode and other settings (temperature, fan speed, etc).
• Press the ON/OFF button (A) again to place the appliance in standby mode.
• Press the timer button (D). The timer light "H" flashes.
• Use the + (E) or - (F) buttons to set the number of hours delay before the appliance comes on.
The time increases or decreases in steps of one hour.
The indicator light (H) flashes until the appliance starts up.
You can set the appliance to come on with a delay of up to 12 hours.
To cancel the timer programme, press the timer button (D) again.
Light (H) stops flashing.
How to programme delayed shut down
• Delayed shut down can be programmed in any operating mode (air conditioning / fan/ dehumidifying).
• Press the timer button (D). The timer light "H" flashes.
• Use the + (E) or - (F) buttons to set the number of hours delay before the appliance goes off.
The time increases or decreases in steps of one hour.
The light (H) flashes until the appliance turns off as programmed.
At the set time, the air conditioner shuts down and remains in standby.
To cancel the timer programme, press the timer button (D) again.
Light (H) stops flashing.
9
Using the remote control unit
(some models only)
MODELS WITH REMOTE CONTROL
• Point the remote control at the receiver on
the air conditioner. The remote control
must be no more than 16,4 ft (5 metres)
away from the appliance (without obstacles between the remote control and the
receiver).
• The remote control must be handled with
extreme care. Do not drop it or expose it
to direct sunlight or sources of heat.
MAX 16,4 ft
MAX 5 metres
DESCRIPTION OF THE REMOTE CONTROL
22) "ON/OFF" button
23) Increase /Decrease button for temperature/programmed use
24) "MODE" button
25) "TIMER" button
26) Fan
speed
selection
button
(MAX/MED/MIN).
27) °F/°C scale button
22
23
Inserting or replacing the batteries
• Remove the cover on the rear of the
remote control;
• Remove the old batteries, if present.
• Correctly insert two new L03 “AAA” 1,5V
batteries (see the instructions inside the
battery compartment);
• Replace the cover.
26
24
25
27
If the remote control unit is replaced or discarded, the batteries must be removed and disposed of in accordance with current legislation as they are harmful to the environment. Do not
mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. Do not dispose of batteries in fire. Batteries may explode or leak.
TURNING THE APPLIANCE ON
Plug the appliance into the mains.
Press the ON/OFF button (22) (when turned on, the air conditioner starts operating in the same
mode as when it was turned off).
Press the MODE button (24) to select the required mode
COOLING
DEHUMIDIFYING
FAN ONLY
On the control panel, the light corresponding to the selected mode comes on.
For air conditioning/dehumidifying/fan only settings and programming the timer, see page 8-9.
10
Tips
To get the best from your air conditioner, follow these recommendations:
• close the windows and doors in the room to
be air conditioned.
The only exception is when the appliance is
installed through a hole in the wall.
In this case, you are recommended to
leave a slight draught through a door or
window to guarantee correct ventilation.
• Never use the appliance in very damp
rooms (laundries for example).
• Never use the appliance outdoors.
GB
close doors and windows
• Protect the room from direct exposure to
the sun by partially closing curtains and/or
blinds to make the appliance much more
economical to run;
• Never rest objects of any kind on the air
conditioner;
• Never obstruct the air intake 6 or outlet
1 grilles;
• Make sure there are no heat sources in the
room.
close blinds or curtains
• Make sure the air conditioner is on a level
floor.
do not cover
the appliance
11
Cleaning
Before cleaning or maintenance, turn the
appliance off by pressing the ON/OFF button
(A) or in models with remote control unit, by
pressing the ON/OFF button 22 , then always
unplug the appliance from the mains socket.
CLEANING THE CABINET
You should clean the appliance with a slightly damp cloth then dry with a dry cloth.
For safety reasons, never wash the air conditioner with water.
Precautions
Never use petrol, alcohol or solvents to clean
the appliance. Never spray insecticide liquids
or similar.
CLEANING THE AIR FILTERS
To keep your air conditioner working efficiently, you should clean the dust filter every week
of operation.
The filter is housed in the intake grille.
To clean the filters, remove the filter as shown
in figure N.
Use a vacuum cleaner to remove the dust
collected on the filter.
If it is very dirty, immerse in warm water and
rinse a number of times.
The water should never be hotter than 40°C.
After washing, leave the filter to dry.
Put the filter back in its housing.
START OF SEASON CHECKS
Make sure the power cable and plug are
undamaged and the earth system is efficient.
Follow the installation instructions precisely.
END OF SEASON OPERATIONS
To drain all water from the circuit, remove the
cap from the drain hose on the back of the
appliance and allow the water to drain out
into a basin (figure O). When the appliance is
empty, replace the cap.
Clean the filter and dry thoroughly before
putting back.
O
N
12
Tr o u b l e s h o o t i n g
NOTE:
NEVER TRANSPORT OR TURN THE APPLIANCE UPSIDE DOWN OR ON ITS SIDE. IF THIS OCCURS,
WAIT 6 HOURS BEFORE TURNING THE APPLIANCE ON, 24 HOURS IS RECOMMENDED. (After the
unit has been on its side, oil needs to return to the compressor to ensure proper function. Without allowing the unit this time (6-24 hours) The unit may function for only a short time, and then
the compressor will break down from lack of oil.)
TROUBLESHOOTING
PROBLEM
n
CAUSE
REMEDY
The air
conditioning unit
does not start.
•
•
•
No electricity.
It is not plugged into the outlet.
The safety device of the plug has
tripped.
•
•
•
Wait.
Plug into the outlet.
Reset the safety device, if
problem persists contact our
toll free customer service.
The air
conditioning unit
works for a short
time only.
•
The air exhaust hose has a constriction.
•
•
The air exhaust hose is blocked.
•
•
There are tight bends in the air exhaust hose. •
Position the exhaust hose correctly.
Check there are no
obstacles. Obstructing air discharge.
Eliminate the tight bends.
The air
conditioner works,
but does not cool
the room.
•
•
Window open.
There are heat sources in the room (lamps,
etc.).
The exhaust hose is detached.
Air filters clogged.
the air conditioner is not powerful enough for
the conditions or size of the room
•
•
close the window.
eliminate the heat source.
•
•
connect the exhaust hose.
clean or replace the filter.
Particular odour in
the room
•
air purifying filters clogged
•
clean or replace the filters.
The air conditioner
does not operate
for about 3 minutes
after turning it on
•
the safety device has tripped
•
wait for three minutes.
The alarm light Q
comes on
•
the tank inside the appliance is full.
•
empty the tank (see "End of
season operations) on page
12).
•
•
•
GB
13
Te c h n i c a l s p e c i f i c a t i o n s
TECHNICAL SPECIFICATION
Power supply voltage
Max. absorbed power
during air conditioning
see rating label
“
Refrigerant
“
Cooling capacity
“
LIMIT CONDITIONS
Room temperature for
air conditioning
70 ÷ 95°F 21 ÷ 35°C
Transport, filling, cleaning, recovery and disposal of refrigerant should be performed by a technical service centre appointed by the manufacturer only.
The appliance should be disposed of by a specialist centre appointed by the manufacturer only.
NEVER TRANSPORT OR TURN THE APPLIANCE UPSIDE DOWN OR ON ITS
SIDE. IF THIS OCCURS, WAIT 6 HOURS BEFORE TURNING THE APPLIANCE
ON, 24 HOURS IS RECOMMENDED. (After the unit has been on its side,
oil needs to return to the compressor to ensure proper function.
Without allowing the unit this time (6-24 hours) The unit may function
for only a short time, and then the compressor will break down from
lack of oil).
This appliance is equipped with a 3 prong grounded plug. The plug must be connected
into an outlet that is properly installed and grounded in the accordance with all local
codes and ordinances. Do not modify the plug provided with the appliance. If it will not
fit the outlet, have a proper outlet installed by a qualified electrician or relocate the unit
to a proper outlet.
If the household electrical supply does not meet the above specifications, or if you are
not sure your home has an effective electrical ground, have a qualified electrician or
your local electrical utility company check it and correct any problems.
SAFETY PLUG
The appliance is fitted with a safety plug to protect the power cable.
If power is cut off, unplug from the outlet and make sure the power cable is undamaged.
If the cable is damaged, call the service center immediately.
If power cuts off frequently and the power cable is undamaged, contact a qualified electrician.
OPERATION OF THE SAFETY PLUG
If the safety device incorporated in the plug trips and cuts off the power supply, check
that the power cable and plug are not damaged.
If the power cable is undamaged, to restore operation press the "RESET" button.
To verify correct operation of the plug, press the "TEST" button periodically and make sure
the appliance disconnects. If this is not the case, contact the service center.
To restore operation, press the "RESET" button.
14
L i m i t e d Wa r ra n t y
De’Longhi is the distributor of Kenwood home appliances.
This warranty applies to all home appliances with De’Longhi or Kenwood brand names
GB
LIMITED WARRANTY
We warrant each De’Longhi AIR CONDITIONER to be free from defects in material and workmanship. From the purchase date, our obligation under this warranty is to provide one (1) year free
parts and labor on the entire AIR CONDITIONER, with an additional four (4) years free on any part
of the sealed system consisting of the compressor, evaporator, condenser and factory connected
refrigerant tubing. Labor and all other parts during the additional four (4) year warranty are to be
paid by the owner. All AIR CONDITIONERS in need of repair are to be shipped to an authorized
De’Longhi service center at the owner’s expense, and De’Longhi will then incur the return shipping costs. After the first five (5) years of ownership, all expenses (all parts, labor and shipping) are
to be paid by the owner of the unit. This warranty shall apply only if the AIR CONDITIONER is used
in accordance with the factory directions that accompany it, and on an Alternating Current (AC)
circuit. This warranty is in lieu of all other warranties and representations, expressed or implied, and
all other obligations or liabilities on our part. We do not authorize any other person or company
to assume for us any liability in connection with the sale or use of our AIR CONDITIONER. This warranty shall not apply to any AIR CONDITIONER that has been repaired or altered outside our factory nor shall it apply to any AIR CONDITIONER that has been subjected to misuse, negligence or
accidents.
If repairs become necessary, see contact information below:
U.S. Residents:
Please contact our toll free hotline at 1-800-322-3848
or log onto our website at www.delonghi.com
CANADA Residents:
Please contact our toll free hotline at 1-888-335-6644
or log onto our website at www.delonghi.com
MEXICO Residents:
Please contact our toll free hotline at 01-800-711-8805
or log onto our website at www.delonghi.com
The above warranty is in lieu of all other express warranties and representations. All implied
warranties are limited to the applicable warranty period set forth above. This limitation does not
apply if you enter into an extended warranty with De’Longhi. Some states/countries do not allow
limitations on how long an implied warranty lasts, so the above exclusions may not apply to you.
De’Longhi does not authorize any other person or company to assume for it any liability in
connection with the sale or use of its appliance.
How does country law apply?
This warranty gives you specific legal rights, and you may also have other rights, which vary from
state to state/country to country.
15
5715110661/11.10
P A C N 9 0E - N 1 0 0 E - N 1 2 0 E
PORTABLE AIR CONDITIONER
CONDITIONNEUR D’AIR PORTATIF
SISTEMA DE AIRE ACONDICIONADO PORTÁTIL
Register this product online and receive a free trial issue of Cook's Illustrated.
Visit www.delonghiregistration.com
Visit www.delonghi.com for a list of service centers near you.
Enregistrez ce produit en ligne et recevez un numéro gratuit de Cook's Illustrated.
Visitez www.delonghiregistration.com
Visitez www.delonghi.com pour y voir une liste des centres de réparation proches de
chez vous.
Registre este producto en línea y reciba un ejemplar gratis de Cook's Illustrated.
Visite www.delonghiregistration.com
Visite www.delonghi.com para ver la lista de centros de servicios cercanos a usted.
Instructions for use
Keep these instructions
Mode d'emploi
Conservez cette notice
Instrucciones para el uso
Repase y guarde estas instrucciones
Lea cuidadosamente este instructivo antes de usar su aparato
ELECTRICAL SPECIFICATIONS 115 V~ 60 Hz
DONNEES ELECTRIQUES 115 V~ 60 Hz
CARACTERISTICAS ELECTRICAS 115 V~ 60 Hz
• Description • Description • Descripción
1
2
56
7
6
3
78
98
11
9
4
10
10
• ACCESSORIES • ACCESSOIRES • ACCESORIOS
11
15
19
13
12
14
17
16
18
21
20
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising