NetWave Series 1-phase

NetWave Series 1-phase
DATA SHEET > NetWave Series 1-phase > 20170523
NETWAVE SERIES (1-PHASE)
PROGRAMMABLE MULTIFUNCTIONAL AC/DC POWER SOURCES
FOR TESTS ACCORDING TO ...
> AIRBUS
> BOEING
> DO 160 Section 16
> EN 61000-3-11
> EN 61000-3-12
> EN 61000-3-2
> EN 61000-3-3
> EN 61000-4-11
> EN 61000-4-13
> EN 61000-4-14
> EN 61000-4-17
> EN 61000-4-28
> EN 61000-4-29
> IEC 61000-3-11
> IEC 61000-3-12 Ed.2:2011
> IEC 61000-3-2
> IEC 61000-3-3
> IEC 61000-4-11
> IEC 61000-4-13
> IEC 61000-4-14
> IEC 61000-4-17
> ...
NETWAVE - SIMULATION OF THE MOST REQUIRED POWER SUPPLY PHENOMENON
The NetWave series (1-phase) are single phase AC/DC power sources, specifically designed to meet the requirements as per
the standards IEC/EN 61000-4-13, -4-14 and -4-28. Used as a DC power source it covers the requirements as per the
standards IEC/EN 61000-4-17 (Ripple on DC) and IEC/EN 61000-4-29 for voltage dips and interruptions on DC supplies.
With its low distortion and high stability, even if supplying dynamic loads, the NetWave series guarantees full compliant
measurements for harmonics and flicker testing as per IEC/EN 61000-3-2,-3-3, -3-11 and -3-12 as well as JIS C 61000-3-2.
The NetWave series is well suited for testing inverters (e.g. solar power, wind power) and e-vehicles.
Additionally, the NetWave series (1-phase) offers the necessary capabilities for avionics testing as per DO-160, Airbus
ABD0100 and Boeing as well as per MIL-STD-704.
HIGHLIGHTS
> Wide Power Bandwidth; DC - 5kHz
APPLICATION AREAS
INDUSTRY
AVIONICS
MEDICAL
MILITARY
RESIDENTIAL
RENEWABLE ENERGY
> Output Power up to 7,500VA AC and 9,000W DC
> Output Voltage max. 360V AC and +/- 500V DC
> High Inrush Current Capability up to 200A
> Extended trigger and control capabilities
(NetWave 7.3)
www.emtest.com
© EM TEST > PAGE 1/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
BENEFITS
SOFTWARE
NETWAVE - THE POWERFUL MULTITALENT FOR AC AND DC
SUPPLY SIMULATION
NETWAVE.CONTROL - EDITING, DOCUMENTING AND
MANAGING YOUR WAVEFORMS AND STANDARD TESTS
The programmable AC and DC power source with its wide
frequency bandwidth offers powerful waveform
generation capabilities for various test applications in the
EMC area and for avionics testing. Based on a
Dual-Processor technology, with an integrated
high-performance PC, a digital signal processor (DSP) and
equipped with a hard disk the NetWave is capable to
generate and record waveforms in realtime.
netwave.control is the tool to easily and conveniently
control the NetWave. By means of netwave.control the
user can program any kind of waveform either composed
from segments or points and download into the NetWave.
Enhanced graphic tools are at hand to adjust the
waveform according to individual requirements.
Its output power with low distortion and high stability,
even if supplying dynamic loads, guarantees full
compliant measurements for harmonics and flicker
testing as per IEC/EN 61000-3-2, JIS C 61000-3-2 and
IEC/EN 61000-3-3 as well as per IEC/EN 61000-3-11 and
IEC/EN 61000-3-12. The NetWave is well suited for testing
inverters of solar and wind power generators and
e-vehicles. Additionally, the NetWave offers full
capabilities for avionics testing as per DO-160, Airbus
ABD0100 and Boeing as well as per MIL-STD-704.
netwave.control provides a library of an extensive
compilation of predefined segments as well as a large
number of standard test routines as per EMC and avionics
standards. netwave.control is also handling any waveform
recorded by other method (e.g. captured by an
oscilloscope) or imported as Excel or CSV files. All
waveforms can be downloaded into the NetWave.
netwave.control offers an enhanced reporting tool to
generate test/measuring reports and can be used under
Windows XP, Windows Vista, Windows 7 and Windows 8.
According to standard requirements a pure sinusoidal
voltage is needed for harmonics and flicker
measurements. The output voltage of the NetWave is
therefore guaranteed to have a very low distortion (THD)
of less than 0.1% regardless of the load.
No matter whether waveforms are programmed of
segments or of single points (normally resulting in MBs of
data) the NetWave will do. Recording of waveforms with
up to 1GByte is easily possible. The measuring channels
are designed to handle up to +/- 500 Vpeak and +/-150
Apeak with 16bit resolution. Interfaces like GPIB, Ethernet
and USB (to connect a memory stick) are common
features with the NetWave.
www.emtest.com
© EM TEST > PAGE 2/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
MODEL OVERVIEW
NETWAVE-SERIES (3-PHASE)
NETWAVE 3 (1-PHASE)
EM TEST ALSO OFFERS 3-PHASE NETWAVE MODELS FOR
ALL APPLICATIONS AND NEEDS
Multifunctional AC/DC source, 3 kVA, as per EN/IEC
61000-4-x standards
NETWAVE 7 (1-PHASE)
Multifunctional AC/DC source, 7.5 kVA, as per EN/IEC
61000-4-x standards
NETWAVE 7.3 (1-PHASE)
Multifunctional AC/DC source, 7.5kVA, as per EN/IEC
61000-4-x standards with built-in isolation transformer
required to perform tests as per aircraft and military
standards
www.emtest.com
The NetWave-series (3-phase) are three-phase AC power
sources with a power capability of up to 90kVA (108kW
DC), specifically designed to meet the requirements as per
IEC/EN 61000-4-13, IEC/EN 61000-4-14, IEC/EN
61000-4-17, IEC/EN 61000-4-27, IEC/EN 61000-4-28. It is
also serving as a DC power source to cover the
requirements as per IEC/EN 61000-4-29 for voltage dips
and interruptions on DC supplies.
© EM TEST > PAGE 3/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
MODEL OVERVIEW
TECHNICAL DETAILS
1-PHASE NETWAVE-MODELS
NETWAVE 3
NetWave 3
Multifunctional AC/DC source,
3,500VA AC / 4,500W DC
Output voltage
0V - 300V AC (RMS)
0V - +/-425V DC
NetWave 7
Multifunctional AC/DC source,
7,500VA AC / 9,000W DC
Output current
NetWave 7.3
Multifunctional AC/DC source,
7,500VA AC / 9,000W DC,
with built-in isolation transformer
required to perform tests as per
aircraft (DO-160, Airbus and Boeing)
and military (MIL-STD-704)
standards
12A (RMS) continuous
21A (RMS) short-term (max. 3s)
100A repetitive peak
NETWAVE 7
Output voltage
0V - 300V AC (RMS)
0V - +/-425V DC
Output current *
26A (RMS) continuous
47A (RMS) short-term (max. 3s)
200A repetitive peak
*(@max. 300V AC, 360V DC)
NETWAVE 7.3
Output voltage
0V - 360V AC (RMS)
0V - +/-500V DC
Output current *
26A (RMS) continuous
47A (RMS) short-term (max. 3s)
200A repetitive peak
*(@max. 300V AC, 360V DC)
EXTENDED CAPABILITIES FOR NETWAVE 7.3
www.emtest.com
SourceAC mode
PLL synchronization with other
voltage sources
Trigger channel
Extended trigger functions
Segment "Step"
Ramping of voltage and/or frequency
in constant time windows
Extern mode
Control of the NetWave by an
external control signal
Simple Mode
Optimized control for integration of
the Netwave into existing
automation environments (for
example Matlab)
© EM TEST > PAGE 4/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
GENERAL SPECIFICATIONS
GENERAL SPECIFICATIONS
SPECIFICATIONS
TRIGGER AND DUT MONITORING
Output frequency
DC - 5,000Hz
Trigger
2 inputs, 2 outputs
Frequency
accuracy
100ppm
DUT monitors
2 inputs, configurable
DC offset with AC
signal
<20mV with linear load
WAVEFORM GENERATOR
Phase accuracy
Resolution 1°
Output noise
< 320mV rms
Slew rate
8V/us
REGULATION
Voltage sense
Internal or external, 4 wires
Distortion (THD)
Less than 0.5%, @50/60Hz
Output voltage
stability
Better than 0.1%
Output voltage
accuracy
Better than 0.5%
Max. compensable
drop on wire
5% of V nominal.
Current limiter
2A to Imax for f < 75Hz (NetWave 3)
5A to Imax for f < 75Hz (NetWave
7.x)
Stop / Current limiter
Protection
Over current, over voltage,
over temperature, low voltage
Segment types DC
DC, Ramp, Square, Triangle,
Sawtooth, Step, Sine, Sine sweep,
Sine ramp, Damped sinewave, Sine
ripple, Profile, Square sweep, Noise,
Sine Dwell, Sinc, Harmonic,
Exponent ...
Segment types AC
Sine, Modulation, Sine sweep,
Sweep on Sine, Sine up/down,
Overswing, Sine offset, Sine Dip,
Sine switching, Harmonic,
Interharmonic, Interharmonic step,
Harmonic distortion ...
Segment duration
Unlimited
OUTPUTS
DUT connection
4mm safety lab connectors
DUT adapter with connector
(depends on country of use)
DISPLAY AND CONTROLS
Display
2-Line LCD, 40 characters
LED indicators
Power On
Active output channel
Trigger
Functional status hard disk
Operation
6 function keys,
Test On key: ON/OFF key for the
power source
www.emtest.com
© EM TEST > PAGE 5/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
GENERAL DATA
OPTIONS
INTERFACES
OPTIONAL ACCESSORIES (FOR NETWAVE 7 ONLY)
GPIB, Ethernet
USB (for memory stick)
RS 232 (input from DPA analyser)
Frame bus (internal system bus)
MT-NetWave
Three-phase matching transformer,
input voltage 3x200V,
output voltage 3x400V,
in separate cubicle
IT-NetWave
Three-phase isolation transformer,
input voltage 3x200 or 3x400V,
output voltage 3x400V,
with 25HU rack (with space to also
house a DPA 500N).
This option is required to use the
NetWave 7 for aircraft and MIL
standard testing.
AMBIENT CONDITIONS
Temperature
5°C - 35°C
Rel. humidity
10% - 90%, non condensing
Atmospheric
pressure
86 kPa (860 mbar) to
106 kPa (1.060 mbar)
MAINS
Supply voltage
OPTIONAL SOFTWARE FOR MODELS NETWAVE 7.X
3 x 400V (3P, N, PE);
3 x 480V (3P, N, PE);
3 x 208V (3P, N, PE) with option
MT-Netwave (NetWave 7) or
NetWave 7.x
Input current
32A (Phase 16A, Neutral 27A)
Line frequency
45Hz - 65Hz
Connector
CEE type 32A
DIMENSIONS
NetWave 3 /
NetWave 7
19", 9HU,
417mm x 449mm x 500mm,
45kg
NetWave 7.3
Minirack, 25HU,
600mm x 800mm x 1250mm,
120kg
www.emtest.com
Lic-1 NetIndustry
Software license for industrial
standards IEC 61000-4-13, -4-14,
-4-17, -4-27, -4-28
Lic-1
NetHarmonics
Software license for harmonics
analysis as per IEC 61000-3-2,
-3-12
and ECE-R10
Lic-1 NetFlicker
Software license for flicker analysis
as per IEC 61000-3-3 and -3-11
Lic-1 NetAircraft
DO
Software license for DO-160
standard
(only for models NetWave 7.3)
Lic-1 Net Military
Software license for MIL-STD-704
standard
(only for models NetWave 7.3),
requires filter Box
F-Box 1 for LDC / HDC 103
Lic-1 NetAircraft
Airbus
Software license for AIRBUS
standards
(only for models NetWave 7.3)
Lic-1 NetAircraft
Boeing
Software license for BOEING
standards
(only for models NetWave 7.3)
Lic-1 NetAmpHigh
Software license for AMP 200N1.x
for extended frequencies up to
500kHz
© EM TEST > PAGE 6/8
DATA SHEET > NetWave Series 1-phase > 20170523
TECHNICAL DETAILS
OPTIONS (ALL MODELS)
OTHER SOLUTIONS
NW-BOARD MEASURING MODULE
OTHER MODELS
Voltage
25V, 50V, 100V, 250V and 500V,
unipolar or bipolar
NetWave Series
(3-phase)
Current
7A, 15A, 30A, 70A and 150A,
unipolar or bipolar
Resolution
16 Bit
OTHER EQUIPMENT
Accuracy
Voltage: better than 0.2%
Current: better than 0.5%
DPA 500N1
Frequency range
DC - 50kHz
Sample rate
5Hz - 100kHz, selectable
Memory
Min. 40GB on hard disk,
File size max. 1GB
Three-phase Multifunction AC/DC
power sources, up to 90,000VA AC
and 108,000W DC
1-phase Harmonics and Flicker
analyzer with built-in Flicker
impedance
ACCESSORIES
FILTER BOX F-BOX 1
Application
Lowpass filter for smoothing the dc
voltage for very low ripple
application < 500 mV
Standard
MIL-HDBK-704-7 HDC 103
MIL-HDBK-704-8 LDC 103
other applications with low ripple
signals
Application
MIL-HDBK
Test condition A (10 Hz)
Test condition B (25 Hz)
Voltage
AC: 230 V
DC: 500 V
Current
32 A
Frequency
max. 60 Hz
Dimension
(LxWxH)
190 x 72 x 110 mm,
plug +24 mm
Weight
0.83 kg
FILTER BOX L-BOX 1-32A
Application
50 µH decoupling coils with
integrated 10 µF capacitor for
MIL-STD-704 LDC
Max EUT Voltage
500 VDC / 360 VAC
Max EUT current
32 A
www.emtest.com
© EM TEST > PAGE 7/8
DATA SHEET > NetWave Series 1-phase > 20170523
COMPETENCE WHEREVER
YOU ARE
CONTACT EM TEST DIRECTLY
Switzerland
USA / Canada
EM TEST (Switzerland) GmbH > Sternenhofstraße 15 > 4153 Reinach >
Switzerland
Phone +41 (0)61/7179191 > Fax +41 (0)61/7179199
Internet: www.emtest.ch > E-mail: sales.emtest@ametek.com
AMETEK Compliance Test Solutions > 52 Mayfield Ave. > Edison > NJ 08837
Phone +1 (732) 417-0501
Internet: www.emtest.com > E-mail: sales.emtest@ametek.com
Germany
AMETEK CTS Germany GmbH > Lünener Straße 211 > 59174 Kamen >
Deutschland
Phone +49 (0)2307/26070-0 > Fax +49 (0)2307/17050
Internet: www.emtest.com > E-mail: info.cts@ametek.de
France
EM TEST FRANCE > Le Trident - Parc des Collines > Immeuble B1 - Etage 3 >
36, rue Paul Cézanne > 68200 Mulhouse > France
Phone +33 (0)389 31 23 50 > Fax +33 (0)389 31 23 55
Internet: www.emtest.fr > E-mail: info@emtest.fr
P.R. China
E & S Test Technology Limited > Rm 913, Leftbank >
No. 68 Bei Si Huan Xi Lu > Haidian District > Beijing 100080 > P.R. China
Phone +86 (0)10 82 67 60 27 > Fax +86 (0)10 82 67 62 38
Internet: www.emtest.com > E-mail: info@emtest.com.cn
Republic of Korea
EM TEST Korea Limited > #405 > WooYeon Plaza > #986-8 > YoungDeok-dong >
Giheung-gu > Yongin-si > Gyeonggi-do > Korea
Phone +82 (31) 216 8616 > Fax +82 (31) 216 8616
Internet: www.emtest.co.kr > E-mail: sales@emtest.co.kr
Poland
EM TEST Polska > ul. Ogrodowa 31/35, 00-893 Warszawa > Polska
Phone +48 (0)518 64 35 12
Internet: www.emtest.com/pl > E-mail: infopolska.emtest@ametek.com
Information about scope of delivery, visual design and technical data correspond with the state of development at time of release. Subject to
change without further notice.
www.emtest.com
© EM TEST > PAGE 8/8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising