ALTV1224C AC/DC Dual Output Power Supply

ALTV1224C AC/DC Dual Output Power Supply
ALTV1224C
AC/DC Dual Output Power Supply
Overview:
Altronix ALTV1224C AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC outputs where
a combination of both AC and DC outputs is required. It provides eight (8) 12VDC outputs with a total current of 3.5A and
eight (8) 24VAC outputs with a total current of 3.5A.
Fig. 1
Specifications:
Input:
+ DC INPUT -
DC
AC
- BAT +
• 115VAC, 50/60 Hz, 1.52A.
Electrical:
• Operating temperature: --- 20º C to 49º C ambient.
• System AC input VA requirement: 174.8VA.
XFMR
AC
MAIN FUSE
MAIN FUSE
Black
Lead
5 6 7 8
P
D1
D1
FUSED
POWER
OUTPUTS
N
R1
POWER
OUTPUTS
DC Outputs
FUSED
LED
INPUT
COMMON
115VAC,
50/60 Hz
1.52A
Input
OFF
1 2 3 4
White
Lead
ON
5 6 7 8
OFF
1 2 3 4
P
ON
• Eight (8) 12VDC @ 3.5A fuse protected outputs.
• Eight (8) 24VAC @ 3.5A fuse protected outputs.
• 7A total output current:
3.5A @ 12VDC;
3.5A @ 24VAC.
• Output fuses are rated @ 3.5A/250VAC.
• Main fuses are rated at 5A/250VAC.
• Filtered and electronically regulated outputs (DC outputs).
• Surge suppression (AC outputs).
AC
Output:
POWER
OUTPUTS
N
R1
LED
INPUT
COMMON
POWER
OUTPUTS
AC Outputs
Features:
• AC/DC power LED indicators.
• Unit maintains camera synchronization.
• Ease of installation saves time & eliminates costly labor.
Enclosure Dimensions (H x W x D):
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
Optional: Available with 220VAC input. Order model # ALTV1224C220.
Installation Instructions:
Wiring methods should be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 2).
Secure enclosure to earth ground.
2. Connect the AC (115 VAC 50/60 Hz) to the two black and white flying leads of the transformers (Fig 1).
3. Measure output voltage before connecting devices. This helps avoiding potential damage.
4. Connect devices to the output terminals using the following procedure (Fig. 1):
Connect each DC device to the terminal pairs on DC output board 1 through 8, marked [P (+) and N (-)],
carefully observing correct polarity.
Connect each AC device to the terminal pairs on AC output board 1 through 8, marked [P (+) and N (-)].
5. Green LED on the PD8s will illuminate when power is present.
6. Upon completion of the wiring secure enclosure door with the screws (supplied).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This
installation should be made by qualified service personnel and should conform to the National Electrical
Code and all local codes.
Terminal Identification:
SMP5BC (Power Supply)
Terminal Legend
AC/ AC
+ DC ----- BAT +
Function/Description
Low voltage AC input (24VAC / 175VA). Altronix part # T24175.
12VDC @ 3.5A total supply current.
N/A.
PD8 (DC Output)
Terminal Legend
1P - 8P
1N - 8N
Function/Description
Positive DC power outputs.
Negative DC power outputs.
PD8 (AC Output)
Terminal Legend
1P - 8P
1N - 8N
Function/Description
AC power outputs.
AC power outputs.
Enclosure Dimensions (H x W x D approximate):
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
1.75”
(44.45mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
1.25”
(31.75mm)
4.5”
(114.3mm)
12.23”
(310.64mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
1.5”
(38.1mm)
4.5”
(114.3mm)
1.1”
(27.94mm)
1.25”
(31.75mm)
0.91”
(23.114mm)
2.0”
(50.8mm)
1.5”
(38.1mm)
15.5”
(393.7mm)
2.0”
(50.8mm)
5.0”
(127.0mm)
5.0”
(127.0mm)
1.1”
(27.94mm)
1.25”
(31.75mm)
0.79”
(20.06mm)
1.25”
(31.75mm)
1.75”
(44.45mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
web site: www.altronix.com, e-mail: info@altronix.com. Lifetime Warranty, Made in U.S.A.
IIALTV1224C - Rev. 113004
A27P
MEMBER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising