SDPro 3D Pedometer

AUSSIE FIT SPORT SCIENCE
SD-PRO 3D MOTION SENSOR PEDOMETER
USER’S INSTRUCTION
Thank you for your purchase of this Aussie Fit Sport Science 3D Motion Sensing Pedometer.
The utmost care has gone into the design and manufacture.
Please read the manual carefully and keep it for further reference.
FEATURES:
•
•
•
•
•
•
•
•
HOW TO INPUT USER SETTINGS
Step and Kcal 7 days memory
10 step filter to eliminate non-step
movements
Suitable for walking / jogging / running
Step counting up 1 to 99,999
Calculates the total distance, speed and Kcal
Exercise Event Timer
Real time clock and date
Metric/Imperial: to switch, press MODE &
DISPLAY Keys together & hold down 5 secs.
PRODUCT DESCRIPTION
1. LCD display
2. MODE button
3. DISPLAY button
4. START/STOP button
5. SPLIT/CLEAR button
1. Set Weight, Walk and Run stride length, Time and
Date. In “today mode”, press and hold MODE button
for 2 seconds until the weight digit flashes.
2. Press SPLIT/CLEAR to decrease value or
START/STOP button to increase value. Press and
hold either button to advance quickly.
3. Press MODE button again to move through the
settings, see diagram below.
4. Press MODE button after last setting to exit and save
the settings or let it exit automatically in 30 seconds
without pressing any button.
6. Removable Clip
7. Battery door
8. RESET button
9. Lanyard position if
required
FUNCTION MODES
Note: To measure your stride length, walk or run 10
steps. The distance from the first step’s toe to the
tenth step’s toe is your total step distance. Divide the
total step distance by 10 to get your average stride
length eg. Total step distance of 700cm divided by 10
steps equals a distance of 70cm per stride.
TODAY MODE
Press the MODE button to switch between modes.
This mode displays total steps and time.
In this mode press either the START/STOP or
SPLIT/CLEAR button to switch between time and date
display.
Press DISPLAY button to check step/distance/Kcal/
time/speed records.
EXERCISE MODE
To record a separate exercise event, press
START/STOP button in this mode to start the
counting function, press it again to stop the
counting.
To record split times in a separate exercise event,
press SPLIT/CLEAR button in this mode to start the
counting function, press again, to pause the display
(counting continues in the background), and press
again to continue counting.
Press the DISPLAY button to check step/distance/
Kcal/time/speed records.
Press SPLIT/CLEAR button again to reset to zero in
this mode.
HOW TO REMOVE CLIP AND BATTERY SAVING
INSULATOR
1. Push the clip and the tiny fastener at the same
time to slide off the clip.
2. Loosen the screw by using a screwdriver.
3. Pull the insulator out in right direction – see
diagram.
4. If needed, you may unscrew the screw to open
the battery door, and place a lanyard in it.
5. Replace the battery door and tighten the screw.
6. Replace the clip if required to clip onto a belt or
waistband.
Note: This total movement is still being registered in
total steps, time, distance, speed and Kcal.
MEMORY MODE
In memory mode, press SPLIT/CLEAR button to
check the records upwards, press START/STOP
button to check the records downwards.
Press DISPLAY button to switch between step and
Kcal records.
Note:
1. The pedometer will have the memory of nearest
7 days’ records
2. The maximum counting is 99,999 steps.
3. Steps below 10 will not trigger to show on the
display. When steps above 10 continuously it
will be added to the total.
RESET BUTTON
In case of malfunction, insert a paper clip wire &
press to reset to default values.
HOW TO WEAR THE PEDOMETER
Pedometer can be worn in any position either
clipped to waist, wrist or watch band; or without clip
in a pocket or carried in a waist bag/bum bag.
BATTERY SAVING
To save battery power, when no movement is
sensed for 3 minutes, the display will turn off
automatically. Data will not be lost in this sleep
mode. Pedometer movement will automatically turn
the display on.
BATTERY REPLACEMENT
When the low battery icon
appears in the display,
this indicates the battery requires replacing. Remove
the clip, loosen and remove the screw on the battery
door, replace with one CR2032 lithium battery.
Attention! Please dispose the used battery in an
ecologically safe manner.
Aussie Fit Sport Science - Warranty against Defects
In certain circumstances Aussie Fit Sport Science provides a warranty to repair or replace certain of its goods, where they are defective, other than
resulting from abnormal use, misuse or where the goods have been subject to any other external factors outside of Aussie Fit Sport Science’s control.
The benefits under any of Aussie fit Sport Science’s warranties are in addition to other rights and remedies you may have at law.
If you are a consumer as defined in the Australian Consumer law, our goods come with a guarantee that cannot be excluded under the Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
If your good is defective and it is within the specified warranty period, as indicated on the goods packaging, and with a receipt of purchase you should
contact Aussie Fit Sport Science. Once you have contacted us in some instances reasonable expenses incurred by you in making the claim may be
reimbursed, eg postage but you must first contact us for authorization. Goods presented for repair may be replaced by refurbished goods of the same
type rather than being repaired. Refurbished parts may be used to repair the goods.
Aussie Fit Sport Science
PO Box 3727
Burleigh Town Centre
Burleigh Heads QLD 4220
Ph/Fax: 07 55763688
sales@aussiefitsport.com.au
www.aussiefitsport.com.au

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project