EVolight Colours 408-412-416 - ETC

EVolight Colours 408-412-416 - ETC
1
408 - 412 - 416 - 424
OWNER’S MANUAL
INDEX
EVOLIGHT
2
____________________________________
Warning:
Control Panel :
Main Menu:
• Address
• Setup
• Dmx in
• Dmx out
• Master Dmx out
• Program Selection
• Master Program
• Info
• Exit
Technical Specifications:
Note:
Warning:
After opening package please make sure the product is in perfect condition.
Gently remove fixture from its packaging and make sure the product has not
been damaged in any way. If you find that the case of the fixture has received
damage, DO NOT CONTINUE UNPACKING AND DO NOT ATTEMPT TO
REPAIR the fixture. Not complying with this recommendation it will void the
warranty. Instead please contact your local agent or the manufacturer. Texts,
specifications of the products can be changed, altered at any time without
notice. For product upgrades and other specifications please click on
www.evolight.it. www.coloursledlight.eu
EVOLIGHT
3
Main Menu
Fixtures ‘ Listings Menu & sub+menues:
_Address
_Setup:
• Temperat
• Max Temp
• DmxSetup
• Defaults
• Sw Vers
• SerNum
• FanSetup
• CalibRed
• CalibGrn
• CalibBlu
• CalibWhi
• SmoothDM
• StBy Col
• Exit
•
_DMX in
_DMX out
_MstDmxO
_ProgrSel:
• Prg 1
• Prg 2
• Prg 3
• Prg 4
•
_MstProg;
• Prg 1
• Prg 2
• Prg 3
• Prg 4
_Info
_Exit
EVOLIGHT
4
Control panel
There are 5 keys available on the Menu to allow for programming
Red “ENTER” key (1) to engage and confirm selection(s)
Yellow “UP” key (2) to move upwards within the Menu
Yellow “UP” key (3) to move downwards within the Menu
Yellow “LEFT” key (4) to move leftwards within the menu
Yellow “RIGHT” key (5) to move rightwards within the menu
Address Menu
DMX ADDRESS:
To change fixture‘s DMX address use UP/Down keys to increase/decrease
DMX value. When required value is displayed, press enter to confirm. Display
backlit goes automatically off after a few seconds.
EVOLIGHT
5
Setup Menu
There are 13 sub-menus in the Setup Menu which give information and other
data about the configuration and the status of Evolight fixture.
TEMPERAT
______________________________________________________
Display shows fixture’s current working temperature
MAX TEMP
Display shows Maximum reached temperature in C° of Evolight fixture
DMXSETUP
Setting DMX value of Evolight fixture
Use keys “Enter, up, down, right, left, to browse through menu. The LCD,
graphic display will guide you to the other lists of options. When entered the
required menu/sub-menu use “UP” “DOUN” key to select mode (“5c
RGBWD” “4c RGBW”
“8c CTO” “3c RGB” “5c HSVW” “14c 16B” “7c RGBW” “4c HSVS”).
Press enter to engage selection. (Dmx table(s) available to show all Evolight
fixtures’ DMX channels)
DEFAULTS
Defaults” menu to reset Evolight fixture to original default factory’s status
Use keys “Enter, up, down, right, left, to browse through menu. When
“Defaults” is located press “Enter” to access sub-menu. Browse through subEVOLIGHT
6
menu using UP/Down key to locate “NONE” & FACT” modes. Select one of
the two modes then press enter to confirm selection.
“Fact” mode brings Evolight fixture to original default factory’s status. None
mode brings you out of the mode without changes.
SW VERS
SW VERS LCD: to check current software version.
Use UP/Down keys to browse through menues. Select SW VERS sub-menu
by shifting the UP/Down keys. When SW VERS is displayed, press enter to
confirm selection. To quit menu press enter again.
SER NUM
“Serial Number” displays fixture’s serial number
Use UP/Down keys to browse through menues. Select “SerNum” sub-menu
by shifting the UP/Down keys. When SerNum is displayed, press enter to
confirm selection. To quit menu press enter again.
FAN SETUP
“Fan Setup” menu to adjust fan speed
Use UP/Down keys to browse through menus. Select “FanSetup in the submenu by shifting the UP/Down keys. When Fansetup is displayed, press
enter to confirm selection. Move the UP/Down keys to “000” and “001”, the
first 000 digits keep fan off at all times unless temperatures reach 40°C, the
latter 001 engages fan on at all times even with low temperature. To confirm
selection press enter.
CALIBRED
Calibred menu allows calibration to tune colours on each individual Red
Green Blue White. This useful mode permits also to tweak and balance slight
differences in the shades of the whites, if ever different LED-binning were
EVOLIGHT
7
used.
Use UP/Down keys to browse through menus. Select “CalibRed” in the submenu by shifting the UP/Down keys. When CalibRed” is displayed, press
enter to confirm selection. Move the UP/Down keys to change any value from
”000 to 255”; when new value is set press enter to confirm selection
CALIBGREEN
Use UP/Down keys to browse through menus. Select “CalibGreen” in the
sub-menu by shifting the UP/Down keys. When CalibRed” is displayed, press
enter to confirm selection. Move the UP/Down keys to change any value from
”000 to 255”; when new value is set press enter to confirm selection
CALIBBLUE
Use UP/Down keys to browse through menus. Select “CalibBlue” in the submenu by shifting the UP/Down keys. When CalibRed” is displayed, press
enter to confirm selection. Move the UP/Down keys to change any value from
”000 to 255”; when new value is set press enter to confirm selection
CALIBWHITE
Use UP/Down keys to browse through menus. Select “CalibWhite” in the
sub-menu by shifting the UP/Down keys. When CalibRed” is displayed, press
enter to confirm selection. Move the UP/Down keys to change any value from
”000 to 255”; when new value is set press enter to confirm selection
SMOOTDIM
“Smoot Dimmer” menu allows for value corrections on the sinusoidal curve
to early on or delay LED starting.
EVOLIGHT
8
Use UP/Down keys to browse through menus. Select “SmootDimm” in the
sub-menu by shifting the UP/Down keys. When SmootDimm” is displayed,
press enter to confirm selection. Move the UP/Down keys to change any
value from ”000 to 255”; when new curve value is set press enter to confirm
selection
STBYCOL
“StBy Color” menu allows for LED zero value corrections on each individual
colour.
Use UP/Down keys to browse through menus. Select “STBCOL” in the submenu by shifting the UP/Down keys. When STBCOL” is displayed, press
enter to confirm selection. Move the UP/Down keys to change any value from
”000 to 255”; To move from one colour to another use the LEFT/RIGHT keys.
When new value is set press enter to confirm selection
EXIT
Press Enter to exit Setup menu.
DMX IN Menu
“DmxIn” Menu allows to view DMX Channels and the IN values of the
Evolight Fixture
Use UP/Down keys to browse through menus. Select “DMXIn” in the submenu by shifting the UP/Down keys. When DMXIn” is displayed, press enter
to confirm selection. Display shows DMX value VL (Value) and CH (Channel).
Move the Right/Left keys to allocate a new DMX value. Press Enter to confirm
and to exit menu.
DMX OUT Menu
EVOLIGHT
9
“DmxOut” allows for DMX, channel operations and to generate a dmx signal
within the fixture; it also generates output DMX signal which can also be used
for other Evolight fixture connected on the same DMX line.
Use UP/Down keys to browse through menus. Select “DmxOut” in the submenu by shifting the UP/Down keys. When DmxOut” is displayed, press enter
to confirm selection. Display shows DMX value VL (Value) and CH (Channel)
Move the Right/Left keys to allocate a new DMX value. Press Enter to exit
menu. (This control system allows for the display to be used as small controldesk)
MST DMX O MENU
Master Dmx Out” allows fort the view of Dmx channels as well to generate
one dmx channel within the fixture,; The selected menu also generates output
DMX signal which can in addition be used for other Evolight fixture
connected on the same DMX line. This feature allows for the first unit to be
used as a master while all the other will act in cascade. When all DMX
channels have been set to their values and show(s) recorded, the Master
Dmx out mode will store and retain configuration(s).
Use UP/Down keys to browse through menus. Select “MstDmxOut” in the
sub-menu by shifting the UP/Down keys. When DmxOut” is displayed, press
enter to confirm selection. Display shows DMX value VL (Value) and CH
(Channel) Move the Right/Left keys to allocate a new DMX value. Press Enter
to exit menu. (This control system allows for the display to be used as small
control-desk). To keep this Master function available, do not exit this menu
when switching the fixture(s) off. When fixture(s) is turned on, Master Menu
will be immediately available in its menu.
PROG SEL Menu
“Program Selection” menu allows for the Evolight fixture to be installed with
pre-sets programs with or without DMX signal.
EVOLIGHT
10
Use UP/Down keys to browse through menus. Select ““ProgSel” in the submenu by shifting the UP/Down keys then press enter. “PRG 01” is then
displayed (01 is program n 1). Use UP/Down keys to scroll list then press
enter to confirm selection. Use Right/Left keys to PLAY PAUSE or STOP. If
Evolight fixture is turned off on “Program Selection, when rebooted it retains
the same configuration. To exit press enter to confirm selection.
MST PROG MENU
Use “Master Program Selection” to pre-store or modify preset programs.
Use UP/Down Keys to scroll through menus. Select “ProSel” then press enter
to confirm selection. PRG 01 (01 = program n 1) will be displayed; scroll
through using UP/Down keys to select program to be modified, press now
enter to confirm selection. Display shows S 01 (S 01= first step of the
program) on the first line while of the second line shows channel and value
“Red 000”. Use the UP/Down keys to change DMX values and use the
Right/Left keys to change dmx channel(s), and time mode, to confirm
selection and to go to step two, press enter to confirm selection. Repeat the
same operation as many time as it is needed to complete your programs. TO
CONFIRM AND CONCLUDE YOUR FINAL SELECTIONS PRESS
RIGHT/LEFT KEY SIMULTANIEOSULY. To review your programs enter
“ProgramSelection” menu.
INFO MENU
Info Menu shows EVOLIGHT Fixture latest software release
Use “UP” e “DOWN” scroll through menu then “Info” . Press enter to view
software reference,
EVOLIGHT
11
DMX TABLE
Setup 3c
RGB
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Greeb
0->255
0->100
3
Blue
0->255
0->100
Setup 4c RGBW
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Green
0->255
0->100
3
Blue
0->255
0->100
4
White
0->255
0->100
Setup 7c RGBW
EVOLIGHT
12
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Green
0->255
0->100
3
Blue
0->255
0->100
4
White
0->255
0->100
Stobe
0->5 off - 6->255
strobe
0->1,9 off - 2->100
strobe
6
Macro
0->5 off - 6->255
rainbow
0->1,9 off - 2->100
rainbow
7
Dimmer
0->255
0->100
5
Setup 8c
CTO
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Green
0->255
0->100
3
Blue
0->255
0->100
4
White
0->255
0->100
Stobe
0->1,9 off - 2->100
0->5 off - 6->255 strobe strobe
6
Macro
0->5 off - 6->255
rainbow
0->1,9 off - 2->100
rainbow
7
Dimmer
0->255
0->100
CTO
0->5 off - 6->255
cto>ctb
0->1,9 off - 2->100
cto>ctb
5
8
Setup 5c RGBWD
EVOLIGHT
13
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Green
0->255
0->100
3
Blue
0->255
0->100
4
White
0->255
0->100
5
Dimmer
0->255
0->100
Setup 4c
HSVS
Channel
Function
DMX
%
1
Colour
0->255
0->100
2
Saturation
0->255
0->100
3
Dimmer
0->255
0->100
Strobe
0->5 off - 6->255
strobe
0->1,9 off - 2->100
strobe
4
Setup 5c HSVW
Channel
Function
DMX
%
1
Color
0->255
0->100
2
Saturation
0->255
0->100
3
Dimmer
0->255
0->100
4
Strobe
0->5 off - 6->255
0->1,9 off - 2->100
EVOLIGHT
14
5
White
saturation
strobe
strobe
0->255
0->100
Setup 14 c
16B
Channel
Function
DMX
%
1
Red
0->255
0->100
2
Red 16B
0->255
0->100
3
Green
0->255
0->100
4
Green
16B
0->255
0->100
5
Blue
0->255
0->100
6
Blu e16B
0->255
0->100
7
White
0->255
0->100
8
White 16B
0->255
0->100
9
Stobe
0->5 off - 6->255
strobe
0->1,9 off - 2->100
strobe
10
Dimmer
0->255
0->100
11
Dimmer 16B 0->255
0->100
12
Reserved
0->255
0->100
13
Frequence
0->255
0->100
14
Freq. 16B
0->255
0->100
Colours 408 Physical dimensions
EVOLIGHT
15
Colours 416 Physical dimensions
EVOLIGHT
16
Colours 412 Physical dimensions
EVOLIGHT
17
Colours 424 Physical dimensions
EVOLIGHT
18
NOTE
EVOLIGHT
19
NOTE
EVOLIGHT
20
Technical specifications
Powered @:
Electrical Input:
90----240V ac
Colours
Colours
Colours
Colours
408
416
412
424
Protection rating:
0,4
0,7
0,6
1,1
A
A
A
A
230V
230V
230V
230V
IP 22
DMX Connector:
Weight:
50-60Hz
5 Pins
Colours
Colours
Colours
Colours
408
416
412
424
EVOLIGHT
3,9
7,2
4,2
7,4
Kg
Kg
Kg
Kg
21
EVOlight srl
Via D. Pesenti 78/17
46046 Medole (MN) Italy
Tel: +39 0376 86 91 07
Fax: +39 0376 89 90 99
e-mail: info@evolight.it
www.evolight.it
EVOLIGHT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising