//Wireless data logger with analog inputs (±5V or ±10V) AN

//Wireless data logger with analog inputs (±5V or ±10V) AN
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
Wireless analog data acquisition System with analog inputs (±5V or ±10V)
//APPLICATIONS
Featured Video
BeanDevice® AN-V Main presentation Video
BeanDevice® AN-V Configuration Video
BeanDevice® AN-V Wireless Range Video
User Manual
BeanDevice® ProcessSensor user manual
Selection Guide
14,6 cm
BeanDevice® ProcessSensor selection guide
6,5 cm
550g
3,35 cm
Mechanical Drawing
BeanDevice® AN-V drawing
// MAIN FEATURES
Analog inputs ±5V or ±10V
( 4 channels )
Integrated rechargeable Lithium-Ion
battery
Wireless transmission IEEE 802.15.4 with
antenna diversity
Embedded data logger up to 1 million
data points
Integrated sensor power supply, software
configurable 4.5V to 20V
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
//EMBEDDED DATA LOGGER UP TO 1 MILLION DATA POINTS
The BeanDevice® AN-V integrates an embedded data logger, which can be used to log data when a Wireless Sensor Networks
can not be easily deployed on your site. All the data acquisitions are stored on the embedded flash and then transmitted to the
BeanGateway® whenever a Wireless Sensor Network is established.
The Datalogger function is compatible with all the data acquisition mode available on your BeanDevice® AN-V :
• LowDutyCycle Data Acquisition
• Survey
• Streaming packet
EXAMPLE : DATA ACQUISITION SYSTEM FOR TECHNICAL BUILDING MANAGEMENT
• The BeanDevice® AN-V is configured with its Datalogger feature. A standalone installation of the BeanDevice® AN-V will be
done (mounted on the walls), without the necessity for any connection to the BeanGateway®.
• Once the sensors are connected, each data is recorded on the embedded flash.
• When needed a technician working on the site can send a request for a log transmission. Then the BeanDevice® AN-V starts
sending all its logs. If all the logs are sucessfully transmitted to the BeanGateway®, the flash memory is erased and new logs
will be recorded.
AN-V
For further information about the Datalogger, please read the following technical note :
TN_RF_007 – “BeanDevice® DataLogger User Guide ”
«rethinking sensing technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
// REMOTE CONFIGURATION & MONITORING
BeanScape® Basic
The BeanScape® application allows the user to view all the data measurements transmitted by the BeanDevice® AN-V.
With the OTAC (Over-the-Air configuration) feature, the user can remotely configure the BeanDevice® AN-V.
SEVERAL DATA ACQUISITION MODES ARE AVAILABLE ON THE BEANDEVICE® AN-V :
• Low Duty Cycle Data Acquisition mode (LDCDA) : the data acquisition is immediately transmitted by radio. The transmission
frequency can be configured from 1s to 24h.
• Survey Mode : the measured value is transmitted by radio whenever an alarm threshold (fixed by the user) is detected (4
alarms threshold levels High/Low). Meanwhile, the device sends frequently a beacon frame informing its current status.
• Streaming Packet Mode : All measured values are transmitted by packet within a continuous flow at 400 samples per second
maximum.
BeanScape ® Premium+ Add-on
The BeanScape® Premium+ integrates an OPC DA server (Data Access). OPC DA is particularly well suited for real time
measurement and data sharing. Each data/measurement can be associated to a tag or its attributes and shared with one or
many OPC clients.
AN-V
For further information about the different data acquisition modes:
TN_RF_008 – “Data acquisition modes available on the BeanDevice®”
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
//CONFIGURABLE SENSOR POWER SUPPLY
The sensor is directly powered by a high accuracy and adjustable DC/
DC converter integrated inside the device. The excitation voltage is
remotely configurable through the BeanScape® (4.5 to 20V).
Product Reference
BND-ANV-NCH-MR
N - Number of data acquisition channels:
4 : 4 channels
MR - Measurement Range
- 5 : ±5V measurement range , - 10 : ±10V measurement range
Example : BND-ANV-4CH-5 , BeanDevice® AN-V with four channels , measurement range: ±5V
Analog data acquisition block specifications
Signal Conditionning
Analog low voltage measurement
Number of channels
4 Channels
A/D Converter
16 bits - SAR Architecture (Successive Approximation Register) with temperature
compensation
Measurement range (analog polarity
is configurable from the BeanScape®)
BND-ANV-NCH-5 - IEEE-BT: ±5V (bipolar) or 0-10 V (unipolar)
Non-linearity error
± 0.5 LSB
Measurement accuracy(@25°C)
Sensor Connector
BND-ANV-NCH-10 - IEEE-BT: ±10V (bipolar) or 0-20 V (unipolar)
< 0,1% when plugged on external power supply
< 0,08% when operating on battery power
M12-5Pins coming with an IP rating IP67 | Nema 6
Sensor wiring code
Sensor wiring code (M12 Socket)
Caption
1 : Pwr+
Pwr+ : sensor power supply (4.5 to 20
Volts)
2 : Sens5 : Not
connected
Gnd : electrical ground
Sens+ : sensor signal + input
4 : Sens+
Sens- : Not used
3 : Gnd
Sensor Power Supply specifications
Excitation voltage range
4.5 Volts to 20Volts , configurable from the BeanScape® software
Excitation voltage accuracy on full
scale range(@25°C)
±0.1%
Maximum Output Power (@25°C)
2 Watts
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
Over-the-air configuration (OTAC) parameters
Data Acquisition mode
•
•
•
Sampling Rate (SPS = samples per
second)
Minimum: 1 SPS
Alarm Threshold
2 high levels alarms & 2 low levels alarms
Sensor power supply
4.5 to 20 Volts
Analog Input polarity
Bipolar or Unipolar
Power Mode
Sleeping with Network Listening & Active
TX Power
18 dBm
Wireless Protocol Stack
IEEE 802.15.4 (2006 version)
WSN Topology
Point-to-Point / Star
Data Rate
250 Kbits/s
RF Characteristics
ISM 2.4GHz - 16 Channels
TX Power
18 dBm
Receiver Sensitivity
-95.5 dBm to -104 dBm
Maximum Radio Range
1 Km (L.O.S)
Antenna diversity
2 omnidirectional N-Type antenna , gain of 2.2 dBi , IP67 | Nema 6
Low Duty Cycle Data Acquisition (LDCDA) Mode: 1s to 24 hour
Survey mode: 1s to 24 hour
Streaming Packet Mode: 400 SPS maximum
Maximum: 400 SPS maximum on each channel
RF Specifications
Embedded Data Logger
Storage Capacity
up to 1 million data points
Wireless data dowloading
3 minutes to download the full memory (average time)
Environmental and Mechanical
Enclosure
Aluminium, Watertight IP65 – Fire Protection : ULV94/Getex
Enclosure dimensions (without antenna) L x W x H : 146.05 mm x 65.5mm x 33.5
mm
Shock Resistance
10g during 50ms
Operating Temperature
-20 °C to +65 °C
Norms
CE Labelling Directive R&TTE (Radio) ETSI EN 300 328
ROHS - Directive 2002/95/EC
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
Power Supply
Integrated battery charger
Integrated Lithium-ion battery charger with high precision battery monitoring :
· Overvoltage Protection
· Battery Temperature monitoring
· Current accumulation measurement
Current consumption @ 3,3V
· During data acquisition : 70mA to 130mA (depends on external sensor power
supply)
· During Radio transmission : 60 mA @ 0dBm
· During sleeping: < 30 µA
External power supply
External power supply : +8v to +28v
Rechargeable battery
Lithium-Ion high density rechargeable battery capacity of 950 mAh
Power-supply bloc
Wall plug-in, Switchmode power Supply 12V @ 1,25A with sealed M8 Plug (IP67 |
Nema 6)
Option(s)
//GETTING STARTING WITH A WIRELESS SENSOR NETWORK
DESCRIPTION
STARTERKIT REFERENCE
Starterkit Wireless System acquisition BeanDevice AN-mV
1 x BeanGateway Ethernet (Indoor version), Ref. : BGTW-ETH-IND
1 x BeanDevice AN-V, Ref. : BND-AN-MV-4CH-IEEE
1 x Beanscape Basic, Ref. : BNSC_BASIC
SK_BND_ANV_4CH_IND
Starterkit Wireless System acquisition BeanDevice AN-mV
1 x BeanGateway Ethernet (Outdoor version), Ref. : BGTW-ETH-OUT
1 x BeanDevice AN-V, Ref. : BND-AN-MV-4CH-IEEE
1 x Beanscape Basic, Ref. : BNSC_BASIC
SK_BND_ANV_4CH_OUT
The BeanDevice® AN-V operates only on our Wireless Sensor Networks, you will need the BeanGateway® and the
BeanScape® for starting a wireless sensor networks.
Product specifications are subject to change without notice. Contact Beanair for latest specifications.
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
AN-V
//product overview
On/Off push
button
Radio Antenna
push button
BeanDevice® Activity
M8-3 Contacts
Socket for external
/Failure led
power supply
Eyelet for wall
mounting
M12-5 Pins female
socket for sensor
interface
«Rethinking Sensing Technology»
Network Context
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
//product overview
Power Supply | Ref: M8-PWR-12V
. Power Supply bloc 12V with M8-3Pins plug
. Watertight - IP67
Molded Cable with M8 | Ref: CBL-M8-2M
. 3POLE - MALE, PVC
. Length : 2meters
. Watertight - IP67
Omnidirectiona antenna 5dBi for outdoor use | Ref: HG_OMNI_5_OUT_DBI
. Waterproof design
. Outoor use
. Professional N-type design reduces stress
. N-type, Male, Reverse Polarity,
. VSWR < 2.0 / Length=95mm
. Wind survival: up to 180Mph / Watertight IP65
N-Type cable (Male/Male) | Ref: CBL_ANT_XXM
. length: 1 meter / 2 meters / 5 meters
. Cable type: RF-5/H155
M12-5 Pins plug for sensor interface | Ref: M12-PL-SENSOR
watertight IP67 - Material: Plastic ABS
M12-5 Pins plug for sensor interface | Ref: M12-AL-SENSOR
watertight IP67 - Material: Aluminum case
«Rethinking Sensing Technology»
AN-V Version
//Wireless data logger with analog inputs (±5V or ±10V)
//CONTACT US
FOR MORE INFORMATION :
sales@beanair.com
Visit our website : www.beanair.com
Visit our blog : www.industrial-wsn.com
OUR YOUTUBE CHANNEL :
Watch our featured videos on Youtube
VISIT OUR WEBSITES
VISIT US !
«Rethinking Sensing Technology»
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising