MODEL OZSD-3000A OZONE GENERATOR

MODEL OZSD-3000A OZONE GENERATOR
EOP-P62-100-7-001-01E/a
MODEL OZSD-3000A
OZONE GENERATOR
INSTRUCTION MANUAL
Published on July 28, 2011
EBARA JITSUGYO CO., LTD.
MEASURING INSTRUMENT
AND MEDICAL DIVISION
MEASURING INSTRUMENT SALES DEPARTMENT
EAST JAPAN SALES BRANCH
: 3-12, Kurigi 2-Chome, Asao-ku,
Kawasaki-shi, Kanagawa, 215-0033 Japan
Tel. +81-44-981-0560
Fax. +81-44-981-0561
E-mail ej-ozone@ejk.co.jp
WEST JAPAN SALES BRANCH
: 2-13, Hiranocho 3-Chome, Chuo-ku,
Osaka-shi, Osaka, 541-0046 Japan
Tel. +81-6-6231-3528
Fax. +81-6-6231-2929
E-mail ozon-osaka@ejk.co.jp
TECHNICAL ENGINEERING DEPARTMENT
3-12, Kurigi 2-Chome, Asao-ku,
Kawasaki-shi, Kanagawa, 215-0033 Japan
Tel. +81-44-981-0560
Fax. +81-44-981-0561
E-mail ejozndsn1@ejk.co.jp
E.J.OZONE PRODUCTS
EOP-P62-100-7-001-01E/a
SAFETY MESSAGE:
Please read this instruction manual before working with the products.
For personal and system safety, and for optimum product performance, make sure you thoroughly understand
the contents before installing, using, or maintaining the product.
Especially the following safety messages and marks are the most important information for human bodies.
Please ensure the safety of all users for our products by reviewing this information.
Important Safety Message
The following safety massages and marks are dangerous items in case of handling the monitor.
Please ensure the safety of all users for our products by reviewing this information.
Mark
Description
DANGER
Call your attention to serious dangerous items.
WARNING
Call your attention to middle dangerous items.
CAUTION
Call your attention to slight dangerous items.
Dangerous Characteristics for Ozone Treatment
Warning
Ozone gas is an injurious material and it may sometimes cause in death when directly breathed it.
And also it affects to accelerate the burning material explosively.
Requirements for precautions to use Ozone generator safety are described in this instruction manual, but in
this section, it is shown to treat Ozone gas as important safety messages.
E.J.OZONE PRODUCTS
-1-
EOP-P62-100-7-001-01E/a
WARNING
1. Prohibition to exhaust ozone gas in atmosphere.
Do not discharge ozone gas in the room, and also do check and maintain loosened points,
deteriorations and damage for piping as they do not make it to have a leakage.
When discharged it, dissolve and exhaust the ozone gas using deozonizer or commercial
base catalyst.
2. Ventilation equipment
Ventilate room air sufficiently, as it dose not cause in serious injury when ozone gas is
leaked.
3. Installation for ozone gas defector or gas alarm
We recommend you to install ozone gas detector or gas alarm, because the gas is dangerous.
4. Prohibition for using fire
Do complete to prohibit works with a fire in the room on which ozone generator is installed.
When work using a fire such as welding is happened, do not use this generator.
5. Shelter
When smelled the ozone gas, based on the leakage, take shelter outside of the room as soon as
possible after the power is turned OFF.
6. Administrator
Decide an a administrator for controlling the ozone gas, and make him to manage the room
i n order to avoid the mistreatment and a dangerous accident.
INTRODUCTION:
Thank you for purchasing the ozone generator Model OZSD-3000A called as "LABO OZONIZER."
We, Ebara Jitsugyo Co., LTD. is producing and selling the ozone generator giving attention to it, as the
performance can be full used.
However, if you have only a mistake for the treatment, the generator will not give a plenty of the performance,
but also it may sometimes cause in trouble.
This instruction manual provides the latest information in order to install and to use correctly and safety, so
that their important messages are described in this manual.
CAUTION
・Read this instruction manual before you begin working with product.
・Do not operate this generator when used a fire, such as welding work.
When required more information on the operation or detailed technical information regarding this instruction,
please consult us them.
Ebara Jitsugyo Co., Ltd. has two assistance number's
Tell : +81-44-981-0560
Fax : +81-44-981-0561
E.J.OZONE PRODUCTS
-2-
EOP-P62-100-7-001-01E/a
List of Contents
1. Unpacking and checking the ozone generator ・・・・・・・・・・ 4
2. Outline of the generator ・・・・・・・・・・・・・・・・・・
2.1 Characteristics ・・・・・・・・・・・・・・・・・・・・・
2.2 Specifications ・・・・・・・・・・・・・・・・・・・・・・
2.3 Outline and function parts ・・・・・・・・・・・・・・・・
4
4
4
5
3. Installation ・・・・・・・・・・・・・・・・・・・・・・・・
3.1 Requirements for installation ・・・・・・・・・・・・・・・
3.2 Pipings ・・・・・・・・・・・・・・・・・・・・・・・・
3.3 Specification of ozone gas line ・・・・・・・・・・・・・・・
3.4 Accessory parts for pipings ・・・・・・・・・・・・・・・・
3.5 How to connect the piping joints ・・・・・・・・・・・・・・
6
6
7
7
7
8
4. Operation ・・・・・・・・・・・・・・・・・・・・・・・・
4.1 Procedure for manual operation ・・・・・・・・・・・・・・
4.2 Procedure for automatic operation ・・・・・・・・・・・・・
4.3 Stopping operation of the monitor ・・・・・・・・・・・・・
10
10
10
10
5. Inspection and maintenance
・・・・・・・・・・・・・・・・・ 11
6. Warranty ・・・・・・・・・・・・・・・・・・・・・・・・・ 11
List of Illustrations and Table
Figure - 1 The front panel and the rear panel ・・・・・・・・・・
Figure - 2 Flow diagram for the ozone generator
・・・・・・・・・ 6
Figure - 3 Controlling ozone concentration in constant
・・・・・・
10
・・・・・・・・・・・・・・・・ 7
Table - 1
Piping specifications
Table - 2
Accessory parts for pipings
Table - 3
Abnormal phenomena and the countermeasures
E.J.OZONE PRODUCTS
5
・・・・・・・・・・・・・
-3-
・・・・
8
11
EOP-P62-100-7-001-01E/a
1. Unpacking and checking the ozone generator
(1) Unpack and check the ozone generator whether it has a damage or not under shipping.
(2) Check the generator whether it is the same one of which you specified or not, when you ordering.
(3) Confirm that screws and bolts installed on this generator are not loose.
2. Outline of the generator
2.1 Characteristics
This ozone generator is designed for the purpose of generating a small amount of ozone and it has some
characteristics as follows.
① It is possible to adjust extensively ozone generation in the range, because pulse counting system is adopted
to control the power for ozone generator.
② It is possible to control ozone concentration by using external signal. (4 ~ 20 mA).
③ Ozone concentration in steady state is obtained from this generator, because the generator unit is controlled
with constant temperature.
2.2 Specifications
(1) Performances
Model
Control method
Material gas
Ozone generation
Concentration
Air to ozonize
Power supply
Power consumption
Dimensions
Weight
OZSD-3000A
silent discharge
dry air which has dew-drop at temperature lower than -40℃ (oxygen is suitable)
3.0 g/h
10.0 g/m3
5
L/min
100 V AC, 50/60 Hz
200 W
480 W×360 D×199 H mm
approx. 18.5 kg
(2) Environment conditions
The environment conditions for this generator are as follows, and it must be used in accordance with this
condition.
1) This equipment is only used indoors. Do not use it outdoors.
2) Temperature
5~35℃
3) Relative humidity
less than 80 % RH
E.J.OZONE PRODUCTS
-4-
EOP-P62-100-7-001-01E/a
2.3 Outline and function parts
Refer to the following illustrations of the front panel and the rear panel.
Figure - 1 The front panel and the rear panel
Front panel
⑤ Flow meter
LABO OZONIZER
④ Output adjusting
trimmer
CONTROL. ADJ
FLOW
② Pilot lamp
P.L
AUTO
① Power switch
POWER
MANUAL
③ Auto/Manual switch
⑥ Joints
Rear panel
OUT
IN
⑨ Terminal
block
AC-100V FUSE
⑦ Fuse holder
⑧ Socket for power cable
① Power switch
② Pilot lamp
③ Auto / Manual switch
Manual
④
⑤
⑥
⑦
⑧
⑨
: This is used when electric power turned on and off.
: This lamp will light up when power switched on.
: It is possible to change the operation to Auto mode or to Manual mode
: It is able to adjust ozone concentration, turning output adjusting
trimmer.
Auto
: This mode controls ozone concentration with external control signal
of 4~20 mA.
Output adjusting trimmer : This trimmer is used to adjust ozone concentration produced from
(CONTROL ADJ)
the generator.
Flow meter
: It is used to adjust flow rate of ozone gas.
Joints
: In ・・・・・ inlet for material gas
Out ・・・ outlet for ozone gas
Fuse / holder
: 100V, 3A / φ6×20 mm
Socket for power cable
: This is used to connect the power cable.
Terminal block
: These terminals are used to connect external control signal of
4 ~ 20 mA as follows.
(1) ・・・・・・・・・・・≈ Polarity
(2) ・・・・・・・・・・・¬ Polarity
E.J.OZONE PRODUCTS
-5-
EOP-P62-100-7-001-01E/a
Figure - 2 Flow diagram for the ozone generator
flow meter
inlet for material gas
supply pressure
0~0.5 MPa
electric poles of ozone
generator
outlet for ozone gas
3. Installation
3.1 Requirements for installation
The ozone gas generator must be installed on the position which is even level with ground, and the material
gas should be kept in dry condition excepting the following precaution.
In order to use the generator in steady stale, and to protect in from any damage, proper considerations for
installation, piping for material gas, power supply and etc., are required to refer to well the following
paragraphs (1) through (5).
(1) Prohibition places for installation.
Install the generator on the places excepting the followings in order to avoid damage and failure and also to
keep safety operation.
① As this generator is designed as one of indoor type enclosure, it is not used where exposed to the water.
② Dusty place and environments where such corrosive gas as hydrogen nitride gas, sulfurous gas, or halogen
gas is flowing around the generator.
③ Environments where is in high temperature and high humidity, and place of radical temperature changes.
④ Places where strong vibration may be happed, or place of which is receiving continuos vibration.
⑤ Place under direct sun shine.
⑥ Places under or near strong magnetic field and electric field, and close to high frequency source.
⑦ Places which have not sufficient spaces to maintain and / or inspect the generator.
⑧ Process plant where explosive gas may be made up in the environment.
DANGER
・Explosion could result in death or serious injury.
Do not use the ozone generator in explosive environments.
・Do not apply sampling gas or water with over pressure than 98kPa to the
generator.
It may have a chance to make the generator to be broken or to have a
burst the encloser or the parts, and also this may cause ozone leakage.
Notice: This product is a precision instrument, so it should be free from shock or vibration.
E.J.OZONE PRODUCTS
-6-
EOP-P62-100-7-001-01E/a
(2) Power supply
When supplying the power source to the generator, use the power source recommended to instrumentation.
If an inductive load and / or a large capacities load are connected to the power line, it can sometimes cause
a surge problem for disturbing the measurement.
(3) Wiring for external control input signal
It is acceptable that a shielded wire is not always used for this signal wiring, but at last, twist pair wire
should be usually used for this wiring.
However, do not use these twisted wires without shielding with power cable in conduit or open tray, and
also avoid to wire it near heavy electric machine.
CAUTION
・In order to avoid dangerous and to protect the generator, install a no-fuse breaker at power line
outdoors.
3.2 Pipings
In this section, requirements for pipings are described.
To prevent an ozone leakage, is required to do carefully the pipings for its gas line, and take care full the
following items.
WARNING
・ As ozone is poisonous to human bodies, install the pipings as it may not have a leakage.
・ If water or liquid will flow backward, the generator may be failed in discharge unit, and it is
dangerous.
3.3 Specifications of ozone gas line
Regarding above specification, refer to Table - 1 below.
CAUTION
・Use ozone resistant materials surely regarding pipings for ozone gas line.
Table - 1 Piping Specifications
Usage
Recommended Materials
tubes, joints pickings,
reaction vessel
Teflon
Pipes, joints, reaction
vessel
stainless steel
(SUS 304, SUS 316)
Pressure limit (absolute)
490.3 kPa
(5 kgf / cm2)
3.4 Accessory parts for pipings
The pillowing parts is attached to this device, as it is materials of the pipings.
E.J.OZONE PRODUCTS
-7-
Table -2 Accessory parts for pipings
Usage
Pipings of inlet and
outlet for ozone gas
Parts
EOP-P62-100-7-001-01E/a
Quantities
Straight joints for tubes
2 PC
Teflon tube φ× 6
5m
3.5 How to connect the piping joints
(1) Stainless joint
Perform to connect a joint, referring the following sketches
・Names of each part
PTFE tube
Cap nut
rear ferrule
insert
body
front ferrule
① Arrange parts as a cap nut (LR), a rear ferrule, a front ferrule and a insert in due order.
② Insert PTFE tube till inner end of body, and connect the cap screw to body, after the parts are moved
toward body.
Drive the cap nut by fingers till it is not moved.
・Tighting method
When tighting the cap nut finally, tighten it more 3/4 turn from position by fingers, using spanner.
E.J.OZONE PRODUCTS
-8-
EOP-P62-100-7-001-01E/a
(2) Teflon (PTFE) joint
Perform to connect a joint in accordance with the procedure with reference of the following sketches.
・ Names of each part
① Insert tube into body and nut cap nut by fingers.
② Tighten the cap nut more 1/4 turn from position which is driven by fingers.
③ After tightening the cap nut, pull the tube slightly and confirm whether it is surely fixed without
looseness.
cap nut
tube
(a)
(b)
(c)
CAUTION
・After connecting the joint, it must be checked for a leakage.
E.J.OZONE PRODUCTS
-9-
EOP-P62-100-7-001-01E/a
4. Operation
4.1 Procedure for manual operation
Operate the generator in accordance with the following procedure.
(1)
(2)
(3)
(4)
(5)
Connect power plug cap to the socket for 100 V AC.
Supply material gas into the generator and adjust flow rate to the specified one.
Set Auto / Manual switch at "MANUAL."
Rotate output adjusting trimmer (CONTROL ADJ.) to end of left side, and turn on the power switch.
Adjust ozone concentration, using the trimmer. Regarding the position and ozone generation, refer to the
performance curve on the ozonizer (ozonizer).
Note : The performance curve is only in reference of the concentration, it is affected by conditions for
Temperature Humidity and Material gas, and also is much changed itself.
4.2 Procedure for automatic operation
This automatic operation mode is used for performing the local operation of the ozone concentration or for
controlling it to constant value, using the controller.
(1) Make wirings between controller output (4~20 mA) terminals and the input terminals on rear panel of the
generator.
(2) Connect analog output (0~5V) of ozone monitor and the input of controller with cable.
(3) Set auto / manual switch at MANUAL position and turn output trimmer to zero.
(4) Adjust concentrations to required value, using ozone monitor and the controller.
(5) Supply material gas at flow rate of 5L/min, using attached air drier.
(6) Reset Auto / Manual switch at AUTO position and turn on the power.
This will make the generator to begin controlling the ozone concentration.
Figure - 3 Controlling ozone concentration in constant
ozone gas
material air
ozone generator
tester
off gas treatment
4 ~ 20 mA DC
controller
ozone monitor
4.3 Stopping operation of the generator
(1) Under when manual operation, turn Output adjusting trimmer to zero position, and switch off the power.
(2) When automatic operation, Auto / Manual switch should be set at MANUAL position, and switch off the
power.
Note : After when used the ozone generator, purge full an ozone gas in it (about 5 minutes) and have the
custody of it.
After above performing, the ozone generator will soon stop its operation.
E.J.OZONE PRODUCTS
- 10 -
EOP-P62-100-7-001-01E/a
5. Inspection and maintenance
In order to use this device for long time without trouble, inspect and maintain the followings.
(1) Routine inspection
① Do not small ozone.
② Check the generator whether it has an abnormal sound and/or a vibration, or not.
③ Check and confirm that the earth terminal is connected to the ground surely.
④ Needs to check air flow rate and the pressure.
(2) Inspection every month
① Check a loose points and a defected points on the pipings
(3) Countermeasure of the generator when has the failure, please consult us.
WARNING
・ As high voltage of 1000V is used for circuit inside of this generator.
・ Disconnect power cable from the plug socket when inspect inside of it.
Table -3 Abnormal phenomena and the countermeasure
Phenomena
Abnormal sound
Countermeasure
When this generator has an abnormal sound, stop the work as soon possible.
Abnormal vibration If the generator begins to vibrate itself, stop the work as soon as possible.
Ozone smell
(an offensive)
(1) By turning off no-fuse breaker outside, stop working the generator soon.
(2) Confirm there is not a fire, and open the windows in order to ventilate it.
6. Warranty
WARRANTY: We warrant the ozone generator as follows.
(1) Warranty period
・12 months after customers acceptance inspection.
(2) Condition
・The ozone generator should be operated under the specified condition described in this instruction
manual.
(3) Limitation of warranty
・Liability and obligations are limited to the supply of parts for replacements.
E.J.OZONE PRODUCTS
- 11 -
EOP-P62-100-7-001-01E/a
MEMO
E.J.OZONE PRODUCTS
- 12 -
荏 原 実 業 株 式 会 社
計測器・医療本部
計測器営業部
■東日本営業課:〒215-0033
神奈川県川崎市麻生区栗木2丁目3番12号
TEL 044-981-0560 FAX 044-981-0561
E-mail ej-ozone@ejk.co.jp
■西日本営業課:〒541-0046
大阪市中央区平野町3丁目2番13号
平野町中央ビル5階
TEL 06-6231-3528 FAX 06-6231-2929
E-mail ozon-osaka@ejk.co.jp
技
術
部
:〒215-0033
神奈川県川崎市麻生区栗木2丁目3番12号
TEL 044-981-0560 FAX 044-981-0561
E-mail ejozndsn1@ejk.co.jp
取扱店:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising