Extech 380803 Appliance Tester/Power Analyzer Extech 380803

actoolsupply.com
User's Guide
Power Analyzer Model 380801
Power Analyzer Datalogger Model 380803
Extech 380803 Appliance Tester/Power Analyzer
Extech 380803 True RMS Power Analyzer Data Logger
Extech 380803-NIST True RMS Power Analyzer Data Logger
1
actoolsupply.com
380801-380803 V7.2 07/13
actoolsupply.com
Introduction
Congratulations on your purchase of the Extech 380801 or 380803 Power Analyzer Datalogger.
This device offers the following features:







Convenient front panel plug-in and testing
Four displays for Watts, PF/VA, V/KHz, Amperes
True power, true RMS for AC Voltage (V) and Current (A)
Datalogger stores over 1000 readings (Model 380803)
Auto Range for Watts and Volts
RS-232 PC Interface
Windows™ Application Software
Careful use of this meter will provide years of reliable service.
Specifications
WATT (Auto Range, AC+DC, Crest Factor < 5)
Range
Resolution
Accuracy
Input
200W
0.1W
±(0.9% reading + 5digts) (50/60Hz)
0-300V, 0-20A,
2000W
1W
±(5% reading + 9digts) (40 to 400Hz)
PF=0.5 to 1
VOLTAGE (True RMS, Auto Range, AC+DC, Crest Factor < 5)
Range
Resolution
Accuracy
200V
0.1V
±(0.5% reading + 5digts) (40 to
Overload Protection
750V
1V
400Hz)
1000VDC/750VAC
CURRENT (True RMS, AC+DC, Crest Factor < 5)
Range
Resolution
2
0.001A
20
0.01A
Accuracy (40 to 400Hz)
Overload Protection
±(0.5% reading + 5digts)
20A, fused
PF (Direct Calculation from W, V, A): PF = Watt / (V * A)
FREQUENCY (Sensitivity 5V)
Range
40Hz to 20kHz
Memory Size (380803)
Resolution
Accuracy
1Hz-10Hz
±(0.5% of rdg ±2digts
1012 x 4 readings (non-volatile)
Memory Life (380803)
100,000 memory writes
Display
2000 count LCD displays
Over Range Indication
‘OL’ displayed on LCD
Sampling Rate
2.5 times per second
Power Source
Eight 1.5V ‘AA’ batteries or AC adaptor
Power Consumption
22 mA approx.
Operating conditions
32 to 122 F (0 to 40 C); Less than 80%
Dimension
13.9"(L) x 11.8"(W) x 3.9" (H)
Weight
3.6 lbs (1.637 Kg) approx.
o
o
352(L) x 300(W) x 100(H)mm
2
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Meter Description
1. Watts display
2. PF or VA display
3. V or KHz display
4. A display
5. 20A fuse
6. Input Receptacle
7. Input Terminal
8. Output Terminal
9. Output Receptacle
10. RS-232 Terminal
11. DC 12V Adaptor Input
12. Hold
13. MAX button
14. PF/VA Select Button
15. REC button (380803)
16. KHz (frequency)
17. On/Off Button
18. Battery Compartment Cover
19. Carrying Handle
20. Storage Space for Accessories
3
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Basic Operation
Warning: If a power source of 220V is connected to the input voltage terminal/receptacle,
do not connect a110V device to the output load terminal/receptacle.
Using Receptacles
1. Plug one end of the power cord into the input receptacle and plug the other end into the wall
outlet.
2. Plug the device to be tested into the output load receptacle. The display will show the W, PF, V,
and A for the device under test.
Note 2: W= VA, 1KW = 1KVA = 1000W = 1000VA, when PF = 1.
Warning: The input receptacle and terminal are connected in parallel (as are the outputs).
To avoid electrical shock, do not touch any metal part of the receptacle or terminal.
Using Terminals
1. Plug one end of the power
leads into the input voltage
terminal (left) and connect
the other end of the test
leads to the power source.
2. Plug the device power
leads into the output load
terminals. W, PF, V, and A
will display for the device
under test.
Note 2: W=VA, 1KW = 1KVA = 1000W = 1000VA, when PF =1 at DC
Warning: The input and output receptacle and terminal are connected in parallel Do not
touch any metal part of the receptacle or terminal to avoid electrical shock.
4
actoolsupply.com
380801-380803 V7.2 07/13
actoolsupply.com
Using a Current Transformer
Warning: Only personnel well trained in the principles of Current Transformers (CT)
should attempt this test connection. When connecting a CT, follow the wiring diagrams
and instructions below.
1 2W
Power Line
K
K
I
L
Motor
1. Connect the CT’s k terminal (entering the CT) to the power line that passes through the CT, and
connect this k terminal to the input voltage black terminal (ground).
2. Connect the other power line to the input voltage red terminal.
3. Connect the CT’s l terminal (leaving the CT) to the output load black terminal (ground).
4. The Watt reading and Amp reading should be multiplied by the CT ratio. The V and PF readings
do not need to be multiplied by the CT ratio.
Warning: The input receptacles and terminals are connected in parallel (as are the
outputs). Do not touch any metal part of the receptacle or terminal.
5
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
PC Interface for Data Acquisition & Datalogging Features
Data Acquisition
Models 380801 and 380803 can be connected to a PC where readings can be logged in real-time as
they are taken. Transferred reading data can be viewed, plotted, statistically analyzed, printed, saved,
and imported in spreadsheet, database, word processing, and other software programs. Instructions
for Data Acquisition are included in the separate Data Acquisition and Datalogging Manual on the
software disc.
Datalogging (Model 380803 only)
The Model 380803 has built-in memory where over one thousand readings can be stored for later
transfer to PC. Once transferred, data can be viewed, plotted, statistically analyzed, printed, saved as
a text file, and imported in spreadsheet, database, word processing, and other software programs
Instructions for Datalogging are included in the separate Data Acquisition and Datalogging Manual.
Note: A “Leading and Trailing bytes” error message can be caused by a RS232 COM port voltage
incompatibility. Use a Serial to USB adaptor to resolve the problem.
6
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Replacement of Batteries and 20A Fuse
Battery Replacement
When the low battery symbol is displayed on any of
the LCDs, replace the eight (8) 1.5V ‘AA’ batteries.
1. Turn off the power analyzer.
2. Open the battery compartment by using a screw
driver (see diagram).
3. Replace the batteries.
4. Replace the battery compartment.
20A Fuse Replacement
To replace the 20A fuse, remove the fuse cover as
indicated in item (5) in the Meter Description section
earlier in this manual and replace the fuse if
necessary.
Warning: Do not replace the blown fuse with a fuse rating greater than 20A.
Measurement of 3-Phase 3-Wire Power
Using One Power Analyzer
Measure WRS first (RST phases must be
correctly identified)
1. Connect the R-phase of the power
source to the black terminal of the
input voltage
2. Connect the S-phase of the power
source to the red terminal of the
input voltage
3. Plug the R-phase of the device to be
tested to the black terminal of the
output load. Do not short the Rphase of the device to be tested to
the R-phase of the input power
source.
4. Record the reading of WRS displayed
on the ‘W’ LCD.
Measure WTS secondly (RST phases must
be correctly identified)
1. Connect the T-phase of the power
source to the black terminal of the
input voltage
2. Connect S-phase of the power
source to the red terminal of the input voltage
3. Plug the T-phase of the device to be tested to the black terminal of the output load. Do
not short the T-phase of the device to be tested to the T-phase of the input power
source.
4. Record the reading of WTS displayed on the ‘W’ LCD.
7
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Using Two Power Analyzers
Measure WRS and WTS (RST phases must be correctly identified)
1.
Connect the R-phase of the power source to the black terminal of the input voltage of
power analyzer 1.
2.
Connect the S-phase of the power source to the red terminal of the input voltage of
power analyzer 1.
3.
Plug the R-phase of the device to be tested to the black terminal of the output load of
power analyzer 1. Do not short the R-phase of the load to the R-phase of the input
power source.
4.
5.
Record the reading of WRS displayed on the ‘W’ LCD of power analyzer 1.
Connect the T-phase of the power source to the black terminal of the input voltage of
power analyzer 2.
6.
Connect the S-phase of the power source to the red terminal of the input voltage of
power analyzer 2.
7.
Plug the T-phase of the device to be tested to the black terminal of the output load. Do
not short the T-phase of the device to be tested to the T-phase of the input power
source.
8.
Record the reading of WTS displayed on the Watt LCD of power analyzer 2.
8
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Using Current Transformers (CT) with 2 Power Analyzers
Measure WRS and WTS (RST phases must be correctly identified)
1.
Connect the R-Phase to the black terminal of the input voltage of power analyzer 1.
2.
Connect the S-phase to the red terminal of the input voltage of power analyzer 1.
3.
Connect the k terminal of CT1 to the R-phase.
4.
Connect the l terminal of CT1 to the black terminal of the output load of power
analyzer 1.
5.
The Watt reading of the power analyzer 1 is WRS
6.
Connect the T-phase to the black terminal of the input voltage of power analyzer 2.
7.
Connect the S-phase to the red terminal of the input voltage of power analyzer 2.
8.
Connect the k terminal of CT2 to the R-phase.
9.
Connect the l terminal of CT2 with the black terminal of the output load of power
analyzer 1.
10. The Watt reading of the power analyzer 2 is WTS
9
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Glossary of Terms
W
PF
V
A
Phase angle
True Watt
Power Factor
True RMS Voltage
True RMS Ampere
Time difference between V and A calculated by
cos-1 (Power Factor)
VA
VAR
IR
Req
IL
XL
Leq
CAP
CR
LF
EPS
EPE
W3
Apparent Power (V * A)
2
2
Reactive Power (SQRT [VA – W ])
Equivalent current (through equivalent resistance)
Equivalent resistance
Equivalent current (through equivalent inductance)
Equivalent impedance of equivalent inductance
Equivalent inductance
Required capacitance
Carriage Return
Line Feed
Datalogger Memory Self-test
Erasing Datalogger Memory
True Power (3 3W)
WRS
Power of R phase with respect to S phase
WTS
Power of T phase with respect to S phase
VA3
Apparent Power (3 3W and Balanced Load)
VAR3
PF3
Reactive Power (3 3W and Balanced Load)
Mean
Std Dev
Best Fit
Mean Value
Standard Deviation
A line drawn to fit a curve with minimum error
Power Factor (3 3W and Balanced Load)
10
actoolsupply.com
380801-380803-EN v7.2 07/13
actoolsupply.com
Warranty FLIR Systems, Inc. warrants this Extech Instruments brand device to be free of defects in parts and workmanship for one year from date of shipment (a six month limited warranty applies to sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department for authorization.
A Return Authorization (RA) number must be issued before any product is returned. The sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. FLIR Systems, Inc. specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or consequential damages. FLIR’s total liability is limited to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied. Calibration, Repair, and Customer Care Services FLIR Systems, Inc. offers repair and calibration services for the Extech Instruments products we sell. NIST certification for most products is also provided. Call the Customer Service Department for information on calibration services available for this product. Annual calibrations should be performed to verify meter performance and accuracy. Technical support and general customer service is also provided, refer to the contact information provided below. 11
actoolsupply.com
380801-380803-EN v7.2 07/13

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project