Ergoline Esprit 770 - Tanning-Bed

Ergoline Esprit 770 - Tanning-Bed
1002479_00_TB_Esprit_USA_070906.qxd
06.09.2007
10:46 Uhr
Seite 1
1002479
ESPRIT 770
OPERATING INSTRUCTIONS
SUN ERGOLINE, A DIVISION OF JK-PRODUCTS & SERVICES, INC.
1 Walter Kratz Drive . Jonesboro, AR 72401
Phone: 800.643.0086 (Toll-free) · Email: ergoline@sunergoline.com
Fax: 870.935.3618 · Website: www.sunergoline.com
Ergoline ESPRIT
OPERATING INSTRUCTIONS
1002479-00- / us / 09.2007
ESPRIT 770 Dynamic Power Temptronic
VHP 10
15046
/0
Identify your tanning device . . . . . . . . . . . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
Identify your tanning device
Customer Service
For contact with Customer Services, please write down
the device number of your tanning device.
5
16054 / 0
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
(800) 445-0624
(870) 935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
3
Skin types
Skin types
Tanning times
For the recommended exposure schedule (see page 5).
Skin type I (Sensitive):
Invariably gets sunburn, accepts little natural sunlight and does not tan.
Skin type II (Fair):
This is the individual that usually burns easily and severely, tans
minimally or lightly and peels.
Skin type III (Average):
Often referred to as “Average” complexion, burns moderately and tans
about average.
Skin type IV (Brown):
This individual burns minimally, tans easily and above average with each
exposure.
Skin type V (Dark Brown):
This individual rarely burns, tans easily and substantially.
4
Tanning times
Tanning times
Note:
Description of skin types see
Page 4.
16050 / 0
“This product is in conformity with performance standards for sunlamp products under CFR21 Part 1040.”
5
Foreword
Foreword
Dear Customer,
The Ergoline device you have purchased is a technically advanced and
powerful product. Your device was manufactured with the greatest care
and precision. It went through numerous quality and safety checks in order to guarantee trouble-free, safe operation. Nonetheless, you can also
make a significant contribution to your long-term satisfaction with your
device. Following the tips and instructions in the instruction manual will
ensure you enjoyment and pleasure with your device.
If you have any questions, we are always available to answer them.
Yours sincerely
JK-Products, Inc.
1) (800) 643-0086
6
1)
• Read and observe the information in this instruction manual. This will
enable you to prevent accidents and provide you with a reliable device ready for use.
• Always observe current legal and other regulations and legal requirements as well as the applicable environmental protection regulations.
Note:
We reserve the right to make technical changes to the illustrations and specifications in this instruction manual.
Reprinting and reproduction, in whole or in part, of this manual is only permitted with our previous written approval and
with the source specified.
Table of Contents
Skin types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tanning times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Important safety notes and information. . . . . . . . . . . . . . . . . 9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Obligations of the salon operator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Instructions pertaining to a risk of fire, electric shock, or injury . . . . . . 11
Instructions pertaining to a risk of damage to the machine . . . . . . . . . 13
Meaning of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Environmental protection information . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Use the sunbed – but use it properly! . . . . . . . . . . . . . . . . . . . . . . . . . 21
Operation at a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Operation buttons and display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operation / Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Operating structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Tanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Interrupt or end tanning session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Running time of accent lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Regulating facial tanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Switching the shoulder tanner off and on . . . . . . . . . . . . . . . . . . . . . . 35
Temptronic – Adjust coolness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Regulating body cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Regulating facial cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Activating AQUA MIST Impulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Switching AQUA MIST comfort program on and off . . . . . . . . . . . . . . 44
Switching AQUA MIST head nozzle off and on . . . . . . . . . . . . . . . . . 46
Switching AQUA MIST body nozzle off and on . . . . . . . . . . . . . . . . . 48
Switching AROMA off and on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7
Table of Contents
Table of Contents
Table of Contents
Table of Contents
Voice Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning/replacing accent lights, canopy . . . . . . . . . . . . . . . . . . . . . . 93
Selecting audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning/replacing accent lights, front panel . . . . . . . . . . . . . . . . . . . 95
Adjusting volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Cleaning filters, sunbed base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Changing music track or studio music channel . . . . . . . . . . . . . . . . . . 57
Cleaning/replacing filter mats, canopy . . . . . . . . . . . . . . . . . . . . . . . 100
Connecting an MP3 player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Temptronic: Emptying condensate tank,
cleaning/replacing the filter mats, cleaning the cooling fins . . . . . . . 101
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Replacing AROMA container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Maintenance instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
AQUA MIST SYSTEM: Replacing canister. . . . . . . . . . . . . . . . . . . . 106
Power Off device and secure against being switched on again. . . . . . 64
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Maintenance: overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Cleaning intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
JK-Products, Inc. – Limited Warranty . . . . . . . . . . . . . . . . 110
Maintenance intervals, installed lamps and order numbers. . . . . . . . . 68
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Relamping / maintenance instructions. . . . . . . . . . . . . . . . . . . . . . . . . 76
Inserting the chip card for the new set of lamps . . . . . . . . . . . . . . . . . 77
Cleaning/replacing UV low-pressure lamps, sunbed base . . . . . . . . . 79
Cleaning/replacing UV low-pressure lamps, side section . . . . . . . . . . 81
Cleaning/replacing UV low-pressure lamps, canopy . . . . . . . . . . . . . . 83
Cleaning/replacing interior lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Cleaning/replacing UV high-pressure lamps/filter panels, canopy
and side section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
8
Timerration – see manual “Intellitan Remote Timer”,
Order no. 801129-..
Please read and observe ...
Important safety notes and information
Description of warning signs
Danger notices, damage to persons:
Type and source of danger, e.g. “DANGER – High voltage!”
Description of the consequences, e.g. “You can be killed or
DANGER! injured by an electric shock!”
Countermeasures:
– Disconnect device from power supply before opening.
Caution notices, damage to property:
Caution!
The word “Caution” with this label points out that danger for
devices, materials and the environment can be expected
here.
Important information:
Note:
This symbol does not identify safety notices, but states information for a better understanding of the processes.
– Do not reach into the inside with the device switched on.
Warning notices, damage to persons:
Type and source of danger, e.g. “Warning – hot surface!”
Description of the consequences, e.g. “You can burn your
WARNING! hand (skin, face)!”
Countermeasures:
– Do not touch hot parts and nearby surfaces.
– Wait until hot parts and surfaces have cooled down.
9
Safety notes
Safety notices
Safety notes
Please read and observe ...
Intended use
Obligations of the salon operator
The tanning device is intended exclusively for cosmetic tanning of the human skin.
• As the operator you are responsible for informing users on possible
risks during tanning.
• The device is meant for commercial use only, not for home use.
• This device is used for tanning one adult person at a time.
• All danger and safety labels attached to the device must be observed!
Do not remove them!
• The user must wear suitable eye protection that blocks UV radiation
during tanning.
• No safety equipment (e.g. panel switch) may be removed or deactivated which can impair the safe operation of the device!
Any other use shall be considered improper. The manufacturer cannot be
held liable for damage or injuries resulting from this. The operator bears
the sole risk for this.
• The device may only be operated in a serviceable condition!
The proper use also includes compliance with the manufacturer’s instructions, operating and maintenance conditions. This device may only be
operated, maintained and repaired by persons familiar with these tasks
and who have been informed of the dangers involved.
10
• The operator is bound to ensure that the equipment is handled correctly.
Please read and observe ...
Instructions pertaining to a risk of fire, electric shock, or injury
You can be killed or injured by an electric shock!
Assembly and electrical connection must comply with naDANGER!
tional and local regulations.
– The device may only be assembled, installed, upgraded
or repaired by specially trained and instructed personnel.
WARNING – ultraviolet radiation!
WARNING!
Unprotected tanning may result in eye injury and eye diseases.
The unprotected eye can become inflamed on the surface,
and in certain cases the retina can be damaged by excessive radiation. Cataracts can form after frequently repeated
exposure to radiation.
– Inform users to use the included protective goggles
that block UV (Order No. 84592-..).
WARNING – ultraviolet radiation! Follow instructions!
Failure to use protective eyewear may result in severe
burns or other eye injury. If discomfort develops, discontinWARNING! ue use and consult a physician.
– A person who does not tan in the sun most likely will not
tan from the use of this device. Persons with very sensitive skins (skin type I) must not use the unit, as with this
skin type tanning is impossible without damaging the
skin (e.g. sunburn).
– Individuals with acute sunburn, individuals who have
had or have skin cancer, or individuals who are at increased risk of skin cancer, must not use the system.
– Seek medical advice if unexpected effects, such as itching, occur within 48 hours of the first session.
– The sunbed must never be used if a filter panel is missing or damaged, or the timer is defective!
– UV light from the sun or UV systems can cause injuries
to the skin or eyes. This biological effect is dependent
on the sensitivity of the individual's skin and on the type
and amount of UV light.
– As with natural sunlight, overexposure can cause eye
and skin injury, sunburn, and allergic reactions.
11
Safety notes
DANGER – High voltage!
Please read and observe ...
Safety notes
– Repeated exposure may cause premature aging of the
skin and skin cancer.
– Medications or cosmetics applied to the skin, may inWARNING!
crease sensitivity to ultraviolet light.
– A person having a history of skin problems should consult a physician before use.
WARNING – ultraviolet radiation!
Danger of long-term consequences.
WARNING! – Overexposure should be avoided.
– The elderly should not use this equipment.
– Nursing infants and small children through age 7 years
may not use this device.
– The following applies to minors under the age of
18 years: Only use tanning devices in agreement with a
parent or guardian, or after consulting a physician.
– While there is no immediate clinical evidence related to
UVA exposure and its effects upon expectant mothers,
it is strongly advised that expectant mothers be discouraged from using the tanning unit.
12
WARNING – risk of infection!
Infections can be transferred through skin contact.
WARNING! All items/equipment components, with which the user can
come into contact during tanning, must be disinfected after
every tanning session:
• Protective goggles
• Headrest
• Sunbed acrylic
• Handles and control panel
Please read and observe ...
Occasionally, persons using the tanning device will experience a slight reddening of the skin – usually in small patches – after the second or third session. This redness is often
accompanied by an itching sensation. This may be nothing
more than a heat “rash” caused by heat from the lamps
within the device. It is generally very limited and caused by
constant contact of the skin with the acrylic surface. It
should go away within approximately 24 hours and should
not reappear. This rashing can be lessened or prevented by
applying moisturizing lotion to the affected area after the
tanning session is completed.
– Follow instructions.
Instructions pertaining to a risk of damage to the
machine
CAUTION – danger of overheating!
Danger of overheating by obstruction of the air routing.
– Do not change, obstruct or block the air inflow and outflow area to the device or make any unauthorized
changes to the device. The manufacturer shall bear no
liability for damage or injuries resulting from such actions.
– Before putting a tanning device into operation, the transport pallet must be removed from under the device.
Danger of overheating by obstruction of the air routing.
– The time between the first two tanning sessions must be
at least 24 hours.
– Increasing tanning also requires an extension of the exposure time (= radiation time) or after a certain degree
of tanning has been achieved, a further intensification is
not possible. However, the radiation time may not be extended as desired within the scope of the permissible radiation doses! Therefore, only a certain degree of final
tanning dependent on the skin type can be achieved
without endangering your health.
– Inform users about proper tanning.
13
Safety notes
Note:
Please read and observe ...
Meaning of symbols
Symbols
General symbols
Filter panels
Contact Customer Service
Cleaning and disinfectant agents
Ergoline key
Part/item number (for orders)
Do not touch, hot surface!
14
Operation
Suction cup
Display of tanning time
Low-pressure lamp(s)
Display of run-on time (fan run-on)
UV low-pressure lamp(s)
Fault display (example)
Starter for low-pressure lamp(s)
Display of Music Channel 1 (Channel 1)
Factory setting: 1 channel
Customer service can set up to 7 channels
UV high-pressure lamp(s)
Display when adjusting volume
e.g.
2s
0-3 min
Description
MP3 player connection
Accent lights
see separate manual
Body cooling by
AQUA SOLAR WITH SKIN+ ADDITIVE
Technical Data
Aroma “Relax”, “Cabin”
Maintenance
Press button
Caution, safety switch!
Press button for 2 seconds
Unscrew/release screw
Duration: 3 minutes
Tighten/lock screw
Speaker
Cleaning
Headphone connection
Replacing
Symbols
Please read and observe ...
15
Please read and observe ...
Clean or replace depending on soiling
Symbols
Draining
Visual inspection
Temptronic
Filter/filter mat
Filter and filter mats must not be damp.
Chipcard of lamp set
...
Continuation of work steps on next page
End of work step
16
Presettings
Guidelines
Product information
This device was built conforming to UL STD 482, and is certified to CAN/
CSA STD C22.2 2 No. 224.
Acrylic glass panels
Export
We would like to point out that these devices are exclusively intended for
use in the USA and Canada and may not be exported to other countries
and operated there! The manufacturer assumes no liability whatsoever
in the event of non-compliance! We explicitly emphasize that high liability
risks may occur for the exporter and/or the operator in the event of noncompliance.
Accessories
Some accessory parts are taken into account in the maintenance schedule beginning on Page 65, however this does not automatically mean that
your device is provided with this equipment.
An overview of the possible accessories is provided in the sales documentation and the planning manual. See page 24 for a selection of these.
The acrylic glass panels for the tanning devices are produced from acrylic plastic developed especially for this application. The acrylics used are
characterized by a particularly high UV permeability and resistance, as
well as an easy-care, hygienic surface that is gentle to the skin.
The acrylic glass panels are formed to their shapes for the specific devices in a technically complex production process. Despite state-of-the-art
production know-how, the presence of minor spots, air bubbles or
streaks in the acrylic panels is unavoidable. In addition, microfine hairline
cracks can occur on the acrylic surface during operation.
These occurrences are material-dependent and are unavoidable in processing, however have no significant effect on the use or value and can
therefore not be recognized as defects.
CAUTION!
Cosmetics or sun screen products must be removed prior to
using the sunbed as they can cause damage (e.g. fine
cracks on the surface) when used continuously.
17
Guidelines / Export / …
Please read and observe ...
Please read and observe ...
Product information
MP3 music (optional) - Advice for the studio owner
If an MP3 player is used privately during tanning, then this does not constitute a public performance in the sense of copyright law, so that no reporting or fee obligation to the corresponding copyright owning company
in respect of copyright exists on the part of the studio operator.
The same regulations apply to the public use of MP3 music files as to all
other music sources. As a studio operator/studio owner, you may only
play original Audio-CDs, MCs, audio-DVDs etc., on your premises and/
or play music via the “MP3-music modules” which are provided in the
professional sunbeds in the Ergoline range, if you have acquired the necessary stage rights1).
Copy-protected audio CDs, MCs, audio DVDs etc., as well as the tracks
included on these media, are not allowed to be converted to MP3 format
and / or stored on hard discs, audio CDs, MCs, audio DVDs etc. when
software and / or computer programs are used for this purpose which
cancel or avoid the copy-protection included on the storage media.
At the request of the external staff or any other controlling body of the responsible company, you must always be in a position to prove that you
have purchased the performance rights by showing the relevant authorisation.
As long you follow the advice given above and have gained of the necessary rights, you may convert your original audio CDs, MCs, audio
DVDs etc. to the MP3 format required for the player. However, you may
1) from the company responsible for granting commercial performance rights
in your country (in Germany: GEMA/GVL)
18
only create one copy (either a duplicate or a conversion to MP3 format)
for each audio CD, MC, audio DVD etc. for which you have obtained the
legal rights. The original sound storage medium must be stored and is
not allowed to be used at the same time.
Please read and observe ...
Maintenance and care
Environmental Declaration – The JK Corporate Group
Extreme danger! High voltage!
The JK corporate group is subject to the strict regulations of EC Directive
761/2001 and the ISO 14001 standard, and undergoes regular internal
and external environment audits performed by trained auditors.
During maintenance work there is a risk of touching live
parts and receiving a fatal electric shock.
Environmental regulations – disposal of lamps
UV-low pressure lamps and UV high-pressure lamps contain fluorescent
materials and other waste containing mercury.
According to the national waste disposal laws and in accordance with the
municipal waste regulations, proof must be provided of the proper disposal of UV lamps.
Your local environmental agency will be happy to assist you with the disposal of UV lamps.
Packaging
All packaging consists of 100 % recyclable materials.
DANGER!
– Disconnect device from power supply before opening –
also see Page 64.
– Do not reach behind covers and do not open the device
with the device switched on.
– Refit any safety devices (e.g. switches) after the work
has been completed.
Maintenance and care play a major role in deciding whether the device
meets the requirements placed on it in a satisfactory manner. The compliance with the specified maintenance intervals and the careful conducting of the maintenance and care work are therefore absolutely necessary
– see Page 65.
The current operating hours of the parts requiring maintenance can be
displayed in the Presetting mode.
Disposal of recyclable materials
CAUTION!
The device has been produced of recyclable materials. When being permanently removed from operation, the device must be disposed of properly. Sun Ergoline will provide you with information on the content or
potential hazards of the materials used.
Only use genuine spare parts of the same type!
The use of other parts may limit or void your manufacturer’s
warranty!
Any liability is excluded in case of damage or injury proven
to be the result of the use of non-genuine spare parts.
19
Environmental protection
information / …
Environmental protection information
Please read and observe ...
Cleaning
Acrylic glass surfaces
Cleaning
CAUTION!
Do not rub with a dry cloth – danger of scratching!
For fast, hygienic proper cleaning of acrylic glass surfaces,
use a specially developed fast disinfectant cleaner.
Other cleaning agents, especially concentrated disinfectants or solvents (e.g. Lysoform, ethyl alcohol or other liquids containing alcohol) must never be used for cleaning.
Failure to observe this voids all warranty claims.
Plastic surfaces
For cleaning the other plastic surfaces, it is best to use warm water and
a leather cloth. Never use aggressive cleaning agents containing alcohol
or essential oils. These may lead, in the long run, to damage not covered
by the warranty.
During cleaning, a slight discoloration of the leather cloth by the rubber
seals must be expected for production-related reasons.
Note:
Prevent damage to plastic surfaces. Remove rings, watches, bracelets etc. before the start of cleaning work.
02756 / 0
20
Please read and observe ...
A few things need to be noted to get maximum enjoyment from a sunbed.
Here are the answers to some frequently asked questions.
Make-up on the sunbed?
Please remove make-up or don't use make-up while tanning. Clean skin
absorbs UV light better.
A wide variety of ingredients are found in cosmetics. Again, whether
these are emulsifiers, greases, or so-called scents – in conjunction with
UV radiation, these can cause allergic reactions of the skin.
Accordingly, a must before using a sunbed is: Remove all make-up. This
is essential. Make-up clogs the pores in the face. The UV light from a
sunbed re-opens these clogged pores so that not only does the light penetrate the skin, but also the allergenic components of the make-up.
A further negative consequence of make-up is that the appearance of the
skin deteriorates irreversibly over a period of time. However good a decent make-up might be – in conjunction with UV light, it causes more
harm than good. Therefore: Remove all make-up before a session on
your sunbed – it will be much better applied afterwards.
Are medications and the sunbed compatible?
It is known that some medications increase the skin's sensitivity to UV
light. This probability is particularly high with antibiotics, sulphonamides,
psychiatric drugs, tranquillizers, anti-diabetes treatments and diuretics.
Sun creams which contain psorale or kumarin also increase skin sensitivity. If you are in any doubt, first ask your doctor – then you can enjoy
the sun at no risk.
Contact lenses on the sunbed?
The answer is: Yes! Like any other sunbed user, contact lens wearers
should also wear special protective goggles which protect the eyes
against UV radiation. To guarantee better protection, wearers of spectacles and contact lenses can ask their optician for exchange contact lenses with UV protection. The UV-A and UV-B filters built into exchange
contact lenses will protect the cornea and the internal parts of the eye
against almost 100% of the energy in UV radiation.
This will benefit sunbed users not only in the open air, but on the sunbed
itself. For more information, ask your optician or optometrist.
Showering after leaving the sunbed?
The browning is in the skin, not on the surface. Therefore you cannot
wash it off. Treat your skin to a moisturizing cream after showering.
21
Use the sunbed properly
Use the sunbed – but use it properly!
Operation
Mandatory reading
Note:
Always read and follow all instructions for proper usage prior to allow
anybody using a tanning device. The operating instructions included with
this device must always be followed to prevent possible injuries or to
reduce them to a minimum.
When describing the operation, the tanning device is often
shown with the canopy open. During tanning the canopy
must always be closed.
Operation
Inform users
• to use provided UV-blocking protective eyewear whenever the
equipment is energized.
• to follow the exposure schedule in accordance with their skin type.
Failure to do so may result in overexposure.
A tanning system is not a toy. You cannot vary the strength of the lamps
in your unit.
Should you have any questions regarding the proper use of your tanning
system, contact Global Service USA at:
(800) 445-0624
7:00 a.m. to 7:00 p.m. (CT)
Warning – ultraviolet radiation!
Danger of skin injuries and skin diseases!
• The sunbed must never be used when a filter panel is
WARNING! missing or damaged, or the timer is defective!
22
Proper operation is not possible with the canopy open.
Device description
1. Facial cooling: air nozzles
16
2. Facial tanner (UV high-pressure lamps)
17
18
3. Shoulder tanner with sound system
12
4. Headphone jack and MP3 connection
6. Acrylic glass panel, sunbed base
13
14
12
15
11
7. Intermediate panel
8. UV low-pressure lamps: sunbed base
9. Body cooling: air nozzles at feet end
10
20
19
10. UV low-pressure lamps: side section
11. UV low-pressure lamps: canopy
2
1
12. AQUA MIST AROMA System nozzles
3
13. Body cooling: air nozzles
4
14. Operating handle
15. Display unit
16. Accent lights: interior
17. Central exhaust air connection (optional)
18. Accent lights: canopy
5
19. Illuminated text
20. Accent lights: front panel
9
8
7
6
07951 / 0
23
Operation
5. Infrared interface
Accessories
3. Shoulder tanner with sound system
17. Central exhaust air connection
3
Operation
17
16014 / 0
24
Operation
Operation at a glance
see separate instructions “Presettings”,
Order no. 1001971
07710 / 0
25
Operation
Operation buttons and display unit
07700 / 0
26
Operation / Navigation
Switch tanning on and off, pause.
Confirm function.
Whether this button is available depends on the function
selected and is shown in the display.
All pictograms on the display unit are illuminated in default mode after
starting up the sunbed.
After selecting a function, the corresponding pictogram flashes and the
setting or selection options for the chosen function are shown in the display. (See “Operating structure” Page 28.)
Note:
If a button is not pressed within 8 seconds, the settings return to
default mode.
Select device function
(go to pictogram)
Select sub-function (if available)
Change setting (progress bar display)
Change music track or studio channel (in default mode)
Whether this button is available depends on the function
selected and is shown in the display.
27
Operation
The sunbed is operated with the buttons on the operating handle in the
canopy.
Operating structure
Operation
Voice Guide
Aqua Mist
Impulse
Own music
Comfort prog.
Track selection
Head nozzle
Studio channels
Body nozzle
Shoulder tanner
Facial fan
Facial tanner
Body fan
Aroma
Volume
28
Temptronic
Tanning
Start of tanning
The device is started automatically with an internal or external timer.
Note:
Timer instructions: see separate manual1).
Operation
Preparation time
Before the UV lamps turn on, you have a few minutes to prepare yourself.
During the preparation time you can switch on the UV lamps at any time
by pressing the START/STOP button.
– Remove your clothes and all jewelry.
– Remove make-up and other cosmetics.
– Remove glasses. Contact lenses can be worn under the protective
goggles.
– Put on the protective goggles.
– Lie down on the bed surface.
– Close the canopy.
– Press the START/STOP button.
07704 / 1
...
1) Order no 801129-..
29
Tanning
Interrupt or end tanning session
Settings on start-up
The tanning session ends automatically after the preset time has run
down. The internal fan continues to run for approx. three (3) minutes to
sufficiently cool the device.
– To interrupt a tanning session, press button START/STOP anytime
during a session.
Operation
– Press START/STOP again to restart the lamps.
07705 / 1
30
Running time of accent lights
The accent lights are automatically switched
on at the end of the tanning session after the
set operating time and are switched off again at
the beginning of the next tanning session.
Stand-by
IR Function
Operation
The running time of the accent lights in the
Standby mode can be changed with the
presettings.
IR Function
07966 / 0
07967 / 0
07812 / 0
see separate instructions
“Presettings”, Order no. 1001971
31
Regulating facial tanners
– Press the up or down button to adjust the intensity of the facial tanners.
– Press the down and OK button to switch the facial tanners off.
Operation
– Press the up button to switch the facial tanners on again.
It takes approx. one (1) minute until the facial tanners reach their full
output.
07889 / 0
1
Facial tanner
Facial tanner
07890 / 0
32
...
Regulating facial tanners
Operation
2
Facial tanner
Facial tanner
07891 / 0
STOP
3
Facial tanner
Facial tanner
Off?
OK
Tanning time
01:26 min.
07892 / 0
33
...
Regulating facial tanners
START
Operation
4
1 min.
Facial tanner
34
Tanning time
03:26 min.
07893 / 0
Switching the shoulder tanner off and on
Operation
– Press the OK button to switch the shoulder tanner off and on.
After switching on again, it takes approx. one (1) minute until the
shoulder tanner reaches its full output.
07878 / 0
STOP
1
Shoulder tanner
Off?
OK
Tanning time
01:13 min.
07879 / 0
35
...
Switching the shoulder tanner off and on
START
Operation
2
1 min.
Shoulder tanner
On?
OK
36
Tanning time
03:26 min.
07880 / 0
Temptronic – Adjust coolness
– Press the up or down button to change the cooling intensity.
Note:
Operation
If the automatic air conditioning (Temptronic) fails, the acrylic
glass panel is cooled without adjustment control. In this event,
the user can only switch the cooling system on or off.
07974 / 0
1
Temptronic 72°F
Temptronic 79°F
07976 / 0
37
...
Temptronic – Adjust coolness
Operation
2
Temptronic 79°F
Temptronic 72°F
07977 / 0
38
Regulating body cooling
Operation
– Press the up or down button to change the intensity of the air stream.
07875 / 0
1
Body fan
Body fan
07876 / 0
39
...
Regulating body cooling
Operation
2
Body fan
Body fan
07877 / 0
40
Regulating facial cooling
Operation
– Press the up or down button to change the intensity of the air stream.
07888 / 0
1
Facial fan
Facial fan
07886 / 0
41
...
Regulating facial cooling
Operation
2
Facial fan
Facial fan
07887 / 0
3
07973 / 0
42
Activating AQUA MIST Impulse
The AQUA MIST function sprays a fine mist of AQUA SOLAR WITH
SKIN+ ADDITIVE in the interior of the sunbed for face and body cooling.
The AQUA MIST AROMA system includes an aroma with the scent “Relax”, which is distributed via the head nozzles.
Operation
– Press the OK button to activate an AQUA MIST impulse.
07984 / 0
1
1X
AQUA MIST
Impulse on? OK
Tanning time
02:35 min.
07986 / 0
43
Switching AQUA MIST comfort program on and off
The AQUA MIST function sprays a fine mist of AQUA SOLAR WITH
SKIN+ ADDITIVE in the interior of the sunbed for face and body cooling.
The AQUA MIST AROMA system includes an aroma with the scent “Relax”, which is distributed via the head nozzles.
Operation
– Press the OK button to switch the AQUA MIST comfort program on
and off.
07984 / 0
1
Comfort prog.
On?
OK
44
Tanning time
02:35 min.
07987 / 0
...
Switching AQUA MIST comfort program on and off
Operation
2
Comfort prog.
Off?
OK
Tanning time
02:55 min.
07988 / 0
45
Switching AQUA MIST head nozzle off and on
Operation
– Press the OK button to switch the AQUA MIST head nozzle off and
on.
07995 / 0
1
Head nozzle
Off?
OK
46
Tanning time
02:55 min.
07989 / 0
...
Switching AQUA MIST head nozzle off and on
Operation
2
Head nozzle
On?
OK
Tanning time
02:55 min.
07990 / 0
47
Switching AQUA MIST body nozzle off and on
Operation
– Press the OK button to switch the AQUA MIST body nozzle off and
on.
07997 / 0
1
Body nozzle
Off?
OK
48
Tanning time
02:55 min.
07991 / 0
...
Switching AQUA MIST body nozzle off and on
Operation
2
Body nozzle
On?
OK
Tanning time
02:55 min.
07992 / 0
49
Switching AROMA off and on
Operation
– Press the OK button to switch AROMA off and on.
07999 / 0
1
Aroma
Off?
50
OK
Tanning time
02:55 min.
07993 / 0
...
Switching AROMA off and on
Operation
2
Aroma
On?
OK
Tanning time
02:55 min.
07994 / 0
51
Voice Guide
Voice Guide gives acoustic guidance when operating the device and is
only available in conjunction with the audio system.
Voice Guide is activated by default during both stand-by and a tanning
session.
Operation
– Press the OK button to switch Voice Guide off and on.
15025 / 0
1
Voice Guide
Off?
OK
52
Tanning time
02:55 min.
15038 / 0
...
Voice Guide
Operation
2
Voice Guide
On?
OK
Tanning time
02:55 min.
15039 / 0
53
Selecting audio system
A
B
Own music
Track selection
C Studio channels
MP3 player
Music SD card
Externally connected systems (e.g. CD
players)
Example:
Operation
Selecting studio channels as audio system
Note:
Selecting an audio system automatically deactivates the others.
– Press the OK button to select the audio system.
15025 / 0
1
A/B/C
Studio channels
On?
OK
54
Tanning time
02:55 min.
15042 / 0
Adjusting volume
Risk of hearing loss!
WARNING!
– With time, the human ear becomes accustomed to high
sound levels.
– The higher you adjust the volume, the quicker the hearing can be damaged.
Operation
– The use of ear pieces and headphones at high volume
can lead to permanent hearing loss.
– Press the up or down button to change the volume.
15025 / 0
1
Volume
Volume
15028 / 0
55
...
Adjusting volume
Operation
2
Volume
Volume
15027 / 0
56
Changing music track or studio music channel
Operation
– Press the up or down button to change the music track or studio music channel.
15025 / 0
1
Change
music track
Track 2
15040 / 0
57
...
Changing music track or studio music channel
Operation
2
Change
music track
58
Track 1
15041 / 0
Connecting an MP3 player
Studio customers can connect their own MP3 player to the device when
the “Audio System” accessory is available.
1
2
Operation
1
2
c
d
15710 / 0
15711 / 0
3.5 mm stereo jack plug.
Connection for an MP3 player: see manufacturer’s instructions.
Loud music might disturb other studio users!
– Use headphones whenever necessary.
...
59
Connecting an MP3 player
Caution!
3
Heat can damage your MP3 player
Operation
– Do not place the MP3 player on the irradiated area.
Cable may be torn off, connectors may be damaged.
– Do not pull cable when unplugging MP3 player.
15712 / 0
60
Technical data
Rated power consumption:
Ergoline Esprit 770
Dynamic Power
Temptronic
–
Rated voltage:
230V
Rated frequency:
60 Hz
Rated fusing:
Powerinput 3-pole
(max. 80 amp)
230V AC 60 Hz
Powerinput 1-pole
(max. 90 amp)
230V AC 60 Hz
80 amp 3-pole
Technical
Data
Model:
Conformity mark:
04045 / 2
61
B
A
Bed tolerance in room
TK
Technical
Data
C1
C
07694 / 1
BK
15222 / 0
max. 135 kg
max. 300 lb
F
D
E1 E2
07695 / 0
62
16049 / 0
A
B
=
=
77 3/8 in
1,965 mm
7
57 /8 in
1,470 mm
C
=
60 13/16 in
1,545 mm
C1 =
D =
54 /16 in
1,380 mm
86 5/8 in
2,200 mm
E1
E2
87 15/16 in
2,234 mm
93 /16 in
33 1/4 in
8 ft
2,380 mm
=
=
F
=
BK =
TK =
5
11
7 1/2 ft
845 mm
2,400 mm
2,300 mm
Acoustic level during tanning
< 81 dB (A)
1m
Technical
Data
Maximum room temperature / Humidity
07393 / 0
LpA
1m
62.9 dB (A)
08587 / 0
07394 / 0
63
Maintenance instructions
Power Off device and secure against being switched on again
Extreme danger!
• A strip of adhesive tape with the wording
“DANGER do not switch ON!” may be applied
over the actuation levers of circuit breakers
which cannot be removed.
If work is to be performed on the devices,
they must be powered off. That means that
DANGER!
all live lines must be switched off.
Switching off the device alone is insufficient,
as certain points may remain energized.
Therefore, switch off and lockout circuit
breakers before performing any work.
01510 / 1
04049 / 0
Maintenance
Extreme danger!
Severe accidents can occur if the device is mistakenly
switched on again.
DANGER!
Immediately after powering off, secure all switches or fuses
used for power against being switched on again.
A prohibition sign with the text:
“Work in progress!”
• “Place: ..............................”
• “Sign may only be removed by: ............”
must always be securely mounted immediately.
01511 / 1
Extreme danger!
DANGER!
64
Prohibition signs must not be hung on or touch live parts.
Maintenance: overview
13
14
15
13
16
17
12
11 2x
1
2
3
9
4
Maintenance
10
5
20
8a
8b
7
see separate instructions “Presettings”,
Order no. 1001971
6
19
18
16058 / 0
65
Scheduled cleaning
15
16
22
1
–

Note:
Clean after every use.
21
Maintenance
4
25
23
07785 / 1

,
–
WARNING – risk of eye
irritation!
Protective goggles may
WARNING! only be cleaned with an
approved disinfectant.

Note:
Confirm cleaning by holding down the START/STOP button (when the follow-up time of the fan in the sunbed has finished).
66
Scheduled cleaning
12
13
14
15
13
16
–
1

4
5

Note:
Clean/drain if necessary!
Maintenance
10

17
20
16057 / 0
67
Scheduled cleaning – filters, filter mats
/50 h
11 2x
Maintenance
6
19
68
18
07783 / 0
 4x
52104-..
98
 2x
843150-..
100
 1x
51975-..
101
 1x
51937-..
101
Scheduled maintenance – AROMA, AQUA MIST

6,000 ml
3652603-..
104
Intervals 1)

1)

8a
8b
7
07782 / 0
100 ml
a) b)
a) Relax:
b) Cabin:
3652003-..
3652203-..
Maintenance
300 h
106
1) Intervals, see “AQUA SYSTEM PRODUCT INFORMATION” (Order no. 801610).
69
Scheduled replacement – accent lights, starters (Design Silverpearl Red)
g
k
g)
1x
white
58 W
1002089-..
93
1x
red
58 W
1002110-..
93
h)
1x
white
8W
11839-..
95
i)
1x
white
58 W
1002089-..
95
1500717-..
95
15 W
1002111-..
85
38 W
1002554-..
85
10047-..
85, 93,
95
h
Maintenance
with 1 x
i
07780 / 1
Makrolon tube red
k) with AQUA MIST AROMA SYSTEM
2x
white
k) without AQUA MIST AROMA SYSTEM
1x
white
6x
S10
1000 h
g) - k)
70
Scheduled replacement – accent lights, starters (Design Candy Orange)
g
g)
2x
with 2 x
h
07780 / 1
58 W
Makrolon tube magenta
1002089-..
93
1500712-..
93
h)
1x
white
8W
11839-..
95
i)
1x
white
58 W
1002089-..
95
1500712-..
95
15 W
1002105-..
85
38 W
1002554-..
85
10047-..
85, 93,
95
with 1 x
i
white
Makrolon tube magenta
Maintenance
k
k) with AQUA MIST AROMA SYSTEM
2x
white
k) without AQUA MIST AROMA SYSTEM
1x
white
6x
S10
1000 h
g) - k)
71
Scheduled replacement – accent lights, starters (Design Ice Blue)
g
k
h
g)
2x
white
58 W
1002089-..
93
h)
1x
white
8W
11839-..
95
i)
1x
white
58 W
1002089-..
95
15 W
1002111-..
85
38 W
1002555-..
85
1002556-..
85
10047-..
85, 93,
95
k) with AQUA MIST AROMA SYSTEM
Maintenance
2x
white
k) without AQUA MIST AROMA SYSTEM
i
07780 / 1
1x
with 1 x
white
Makrolon tube blue
1000 h
g) - k)
72
6x
S10
Scheduled replacement – UV lamps
500 h
a
d
b
f
a), b)
4x
Ergoline Ultra
520 W
12645-..
88
f)
2x
Ergoline Ultra
250 W
1500384-..
–
c)
18 x
Ergoline
VHP10 Dynamic Power
200 W
1004452-..
79
d)
8x
Ergoline
VHP10 Dynamic Power
200 W
1004452-..
81
e)
22 x
Ergoline
VHP10 Dynamic Power
200 W
1004452-..
83
1000 h
c
Maintenance
e
07779 / 2
c), d), e)
Chipcard of lamp set
77
Note:
The UV high-pressure lamps used can be
operated with different wattages.
UV low-pressure lamps: Clean with plain
water (damp cloth).
73
Scheduled replacement – filter panels, acrylic glass panels
1500 h
b
 1x
a
79
1500339-..
79
3000 h
f
4
Maintenance
735377-..
5
 1x
a)
2x
Ultra Performance 512s
1004523-..
88
b)
2x
Ultra Performance 512s
1004522-..
88
f)
2x
Ultra Performance 912
1500635-..
–
2x
uncoated
1500160-..
–
16052 / 0
Filter panels: Clean with plain water
(damp cloth).
74
Scheduled maintenance – fan
40000 h

Body ventilator (head end)
735326-..
–

Facial ventilator
735326-..
–

Intermediate panel ventilator
735326-..
–

Main ventilator
12873-..
–

Body ventilator (feet end)
13010-..
–
26
27
30
29
07778 / 1
Maintenance
28
75
Relamping / maintenance instructions
It is imperative that you, the owner and/or operator, check all components for any signs of wear which may occur through normal use.
CAUTION – Damage due to improper maintenance!
Observe the cleaning and maintenance schedule specified in the maintenance table on Page 66 to 75.
Improper maintenance can cause the device to be damaged or to become unusable.
Only replace UV low-pressure lamps with the original lamp type or with
compatible lamps.
Only replace UV high-pressure lamps with the original lamp type or with
compatible lamps.
Risk of burning!
Maintenance
When changing the UV low pressure lamps, the enclosed
chip card must always be used! The UV low pressure
WARNING!
lamps can only be operated at the correct power if the
lamp set and chip card are exchanged simultaneously.
If the old chip card is left in the unit, the new lamp set is
operated at too high power and the user may suffer heavy
burns!
Should you require any assistance or need additional information, please
call Global Service USA at (800) 445-0624, Monday through Friday
7:00 a.m. - 7:00 p.m. CT, Saturday 8:00 a.m. to 3:00 p.m.
– Always comply with the specified maintenance intervals.
– Follow the cleaning instructions.
– If the maintenance intervals for the UV lamps are exceeded or incompatible UV lamps are installed, the share of harmful UVB radiation
may increase. Sunburn and other skin damage may result.
Danger: of burns from hot lamps and device parts!
If the tanning device was operated before being switched
WARNING! off and opened, lamps and housing parts may be hot.
– Before replacing lamps or other spare parts, wait until
lamps and metal parts of the device have cooled down
sufficiently.
Danger of pinching!
When opening and closing the tray, panels and covers, you
can pinch your fingers.
76
Inserting the chip card for the new set of lamps
Power Off!
1
3
2
1001417-
1
15033 / 0
Maintenance
07750 / 0
16047 / 0
2
16018 / 0
...
07751 / 0
77
Inserting the chip card for the new set of lamps
4
Maintenance
15034 / 0
5
07752 / 0
78
Cleaning/replacing UV low-pressure lamps, sunbed base
4
07723 / 0
07712 / 0
07715 / 0
Maintenance
2
Power Off!
3
1
07713 / 0
5
07714 / 0
1
2
03108 / 0
79
...
Cleaning/replacing UV low-pressure lamps, sunbed base
6
7
9
1
2
Maintenance
03099 / 0
Note!
07716 / 0
8
Inserting the chip card for the new
set of lamps, see Page 77.
07717 / 0
80
07718 / 0
Cleaning/replacing UV low-pressure lamps, side section
2
4
2
03108 / 0
Maintenance
16024 / 0
07719 / 0
1
Power Off!
1
3
2
1
07720 / 0
...
07721 / 0
81
Cleaning/replacing UV low-pressure lamps, side section
5
6
16025 / 0
Maintenance
03099 / 0
Close:
Note!
Inserting the chip card for the new
set of lamps, see Page 77.
7
1
2
07722 / 0
82
Cleaning/replacing UV low-pressure lamps, canopy
2
Caution!
The canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
acrylic glass panel. Such failure is
not covered by manufacturer's
warranty.
07726 / 1
Maintenance
07724 / 0
Power Off!
Danger of injury from the canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
3
1
2
3
1
1
– Support canopy panel.
2
– Loosen screws in the specified order.
1 2 3
07725 / 0
07770 / 0
83
...
Cleaning/replacing UV low-pressure lamps, side section
4
1
7
Note!
2
Inserting the chip card for the new
set of lamps, see Page 77.
3
1
1 2 3
Maintenance
03108 / 0
07727 / 0
6
5
2
1
03099 / 0
84
2
07771 / 0
Cleaning/replacing interior lighting
2
Caution!
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
acrylic glass panel. Such failure is
not covered by manufacturer's
warranty.
07726 / 1
Maintenance
07728 / 0
Power Off!
Danger of injury from the canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
3
1
2
3
1
1
– Support canopy panel.
2
– Loosen screws in the specified order.
1 2 3
07725 / 0
07770 / 0
85
...
Cleaning/replacing interior lighting
if available
4
6
1
8
2
3
4
Maintenance
07772 / 0
5
1
3
2
2
4
07773 / 0
86
9
7
1
07162 / 0
07774 / 0
07769 / 0
...
Cleaning/replacing interior lighting
if available
Close:
12
14
1
2
2
4
3
07165 / 0
1
07775 / 0
07771 / 0
Maintenance
10
Close:
13
11
15
3
4
2
1
3
2
1
1 2 3
07166 / 0
07776 / 0
07727 / 0
87
Cleaning/replacing UV high-pressure lamps/filter panels, canopy and side section
Open: side section panel:
Danger of injury from the canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
1
2
– Support canopy panel.
– Loosen screws in the specified order.
Maintenance
15229 / 0
Power Off!
Caution! Risk of breakage and
scratching!
Do not open canopy and side section at the same time otherwise
the panels scratch against each
other. Replace one after the other.
1
Caution!
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
acrylic glass panel. Such failure is
not covered by manufacturer's
warranty.
07720 / 0
2
16024 / 0
88
...
Cleaning/replacing UV high-pressure lamps/filter panels, canopy and side section
Clean/replace: UV high-pressure lamps
and filter panels
3
2
07721 / 0
07726 / 1
1
3
Maintenance
Open: canopy panel:
1
2
3
1
1
2
1 2 3
07725 / 0
07770 / 0
07730 / 0
89
...
Cleaning/replacing UV high-pressure lamps/filter panels, canopy and side section
DANGER! Fire hazard!
4
2
1
JK csc vbvbrnfci
3
2
– Only fit high pressure lamps
recommended by Ergoline.
Maintenance
5
3
07732 / 0
– Clean the inside of the device
regularly. Foreign materials
could be flammable!
07733 / 0
07731 / 0
90
High pressure lamps that have
not been approved by Ergoline
DANGER!
can explode. Hot lamp components can set other parts on fire.
People can be killed or severely
injured due to smoke and fume inhalation.
6
04044 / 1
...
Cleaning/replacing UV high-pressure lamps/filter panels, canopy and side section
– Check safety switch.
8
10
– Only touch new UV high-pressure lamp on the gripping surface – see Figures 6 and 7.
2
07735 / 0
9
1
07736 / 0
Maintenance
7
3
JK csc vbvbrnfci
CAUTION!
Do not touch the glass bulbs of
the UV high-pressure lamps with
your bare fingers! Remove soiling
thoroughly.
11
JK csc vbvbrnfci sdsx dsef
07734 / 0
07738 / 0
07737 / 0
91
...
Cleaning/replacing UV high-pressure lamps/filter panels, canopy and side section
Close: side section:
Close: canopy:
1
1
2
1
Maintenance
16025 / 0
Close:
07771 / 0
Close:
2
2
3
1
1
2
2
1 2 3
07722 / 0
92
07727 / 0
Cleaning/replacing accent lights, canopy
2
4
1
07740 / 0
2
07769 / 0
07742 / 0
Maintenance
1
2
3
if available
Power Off!
1
3
1
5
2
07741 / 0
07745 / 0
07162 / 0
93
...
Cleaning/replacing accent lights, canopy
6
8
10
2
Maintenance
07166 / 0
if available
9
7
3
1
07165 / 0
94
2
07743 / 0
1
07744 / 0
Cleaning/replacing accent lights, front panel
2
4
07751 / 0
07748 / 0
Maintenance
07746 / 0
Power Off!
1
5
3
1
1
2
07750 / 0
07747 / 0
2
03350 / 0
95
...
Cleaning/replacing accent lights, front panel
6
8
10
2
1
1
Maintenance
07749 / 0
07754 / 0
if available
7
9
03099 / 0
96
11
07753 / 0
07162 / 0
...
Cleaning/replacing accent lights, front panel
14
16
07756 / 0
07755 / 0
Maintenance
12
if available
15
13
07165 / 0
17
07166 / 0
07752 / 0
97
Cleaning filters, sunbed base
Hand-wipe lightly, dry or with water,
or use a vacuum cleaner.
4
2
07751 / 0
Maintenance
07757 / 0
07759 / 0
Power Off!
1
1
When re-assembling, the cleaned
filter mats must be dry.
2
07750 / 0
98
Attention! The system can be
damaged by moisture!
3
07758 / 0
...
Cleaning filters, sunbed base
5
Maintenance
07760 / 0
6
07752 / 0
99
Cleaning/replacing filter mats, canopy
Rinse with water or replace.
2
Maintenance
07761 / 0
1
04047 / 0
Attention! The system can be
damaged by moisture!
2
When re-assembling, the cleaned
filter mats must be dry.
1
07762 / 0
100
3
07763 / 0
Temptronic: Emptying condensate tank, cleaning/replacing the filter mats,
cleaning the cooling fins
Attention! Risk of damage to
the system!
2
Check the filter mats and the cooling fins on the air conditioner regularly and clean as necessary.
Maintenance
07751 / 0
Power Off!
1
3
1
07764 / 0
2
3
1
2
07750 / 0
04043 / 0
101
...
Temptronic: Emptying condensate tank, cleaning/replacing the filter mats, cleaning the cooling fins
Clean carefully (vacuum or
wash) or replace.
4
6
8
03244 / 4
Maintenance
Clean carefully.
08101 / 1
Hand-wipe lightly, dry or with water,
or use a vacuum cleaner.
5
Attention! The system can be
damaged by moisture!
7
When re-assembling, the cleaned
filter mats must be dry.
07464 / 0
102
03319 / 0
...
Temptronic: Emptying condensate tank, cleaning/replacing the filter mats, cleaning the cooling fins
9
11
2
1
07752 / 0
Maintenance
07465 / 0
10
04841 / 2
103
Replacing AROMA container
2
4
2
2
1
1
BIS
AR RE
LTB EFO
HAST B
BE 007
02
Maintenance
OPE
07751 / 0
07765 / 0
/2
ON
NED
03354 / 2
Power Off!
1
3
1
5
2
2
1
1
BIS
AR RE
LTB EFO
HAST B
BE 007
02
/2
NE
N
DO
OPE
07750 / 0
104
07766 / 0
3/2
08/0
06488 / 0
...
Replacing AROMA container
6
2
1
2
Maintenance
07767 / 0
7
07752 / 0
105
AQUA MIST SYSTEM: Replacing canister
3
2
07751 / 0
Maintenance
16053 / 0
Power Off!
1
Health hazard!
1
WARNING!
2
4
Impurities in the AQUA MIST can
present a health hazard.
– Use only original Sun Ergoline
AQUA MIST!
– Replace the entire canister.
– Do not top up or mix with tap
water or other liquids!
07750 / 0
106
– Do not swallow!
...
AQUA MIST SYSTEM: Replacing canister
5
9
7
6
60 sec
6
8
07788 / 0
Note:
For venting after canister replacement you must enter presetting
mode and choose function 231
(see separate instructions “Presettings”, Order no.: 100 1971)
07787 / 0
107
Maintenance
07752 / 0
Index
Index
Index
A
Accent lights
Cleaning/replacing ....................... 93, 95
Maintenance schedule ........... 70, 71, 72
Accessories .......................................... 17, 24
Acoustic level.............................................. 63
Acrylic glass, cleaning ................................ 20
Activating AQUA MIST Impulse.................. 43
Air conditioning unit, filter mats................. 101
Allergies ...................................................... 21
AQUA MIST
Body nozzle ....................................... 48
Head nozzle ....................................... 46
Replacing canister ........................... 106
AQUA MIST comfort program,
switching on and off .................................... 44
AROMA
Replacing container ......................... 104
Switching on and off........................... 50
B
Bed tolerance in room................................. 62
Body cooling, regulating ............................. 39
108
C
Canopy
Interior lighting.................................... 85
Replacing UV-lamps........................... 83
Care ............................................................ 19
Changing music track.................................. 57
Changing studio music channel .................. 57
Chip card of lamp set ............................ 76, 77
Cleaning ...................................................... 20
Cleaning schedule....................................... 66
Conformity mark.......................................... 61
Connecting an MP3 player.......................... 59
Contact lenses ............................................ 21
Container AROMA .................................... 104
Cooling fins, air condition .......................... 101
D
Description of tanning device...................... 23
Disinfection.................................................. 20
Disposal of lamps........................................ 19
E
Ending tanning session............................... 30
Environmental protection ............................ 19
Error codes................................................ 114
F
Facial cooling, regulating.............................41
Facial tanner
Regulating ..........................................32
Replacing high-pressure lamps ..........88
Fault codes................................................114
Filter in sunbed base ...................................98
Filter mats
Air conditioning unit ..........................101
Canopy .............................................100
Filter panels, maintenance schedule.....73, 74
Filters in sunbed base .................................98
Frequency ...................................................61
Fusing..........................................................61
G
Glasses .......................................................21
Global Service USA, address........................3
Guidelines ...................................................17
H
Humidity ......................................................63
Index
L
Lamps, disposal.......................................... 19
Load, maximum .......................................... 62
M
Maintenance ............................................... 65
Maintenance and care ....................... 19
Maintenance schedule ........... 68, 69, 75
Overview ............................................ 65
Safety information .............................. 76
Make-up...................................................... 21
Medication .................................................. 21
MP3 music, product information ................. 18
O
Operating controls ...................................... 26
Operation at a glance ................................. 25
Operator commitments ............................... 10
P
Packaging ................................................... 19
Plastic surfaces........................................... 20
Power consumption .................................... 61
Power, switching off.................................... 64
Preparation time.......................................... 29
Proper use................................................... 10
Protective goggles................................. 21, 29
R
Relamping ................................................... 76
Replacing the chip card for the new set of
lamps........................................................... 77
Room temperature, maximum..................... 63
Running time of accent lights ...................... 31
S
Safety information, maintenance................. 76
Scheduled cleaning..................................... 66
Scheduled maintenance.................. 68, 69, 75
Selecting an audio system .......................... 54
Shoulder tanner, switching on and off......... 35
Showering ................................................... 21
Side section
Replacing high-pressure lamps.......... 88
Replacing UV lamps........................... 81
Skin sensitivity............................................. 21
Skin types...................................................... 4
Spare parts.................................................. 19
Starting tanning........................................... 29
Sunbed base, replacing UV lamps.............. 79
Sunbed, how to use it.................................. 29
T
Tanning .......................................................29
Tanning instructions ....................................21
Technical data .............................................61
Temptronic, adjust coolness........................37
Timer ...........................................................29
Troubleshooting.........................................114
U
Using the sunbed ........................................29
UV high-pressure lamps
Canopy ...............................................88
Side section ........................................88
UV lamps, maintenance schedule...............73
UV low-pressure lamps
Canopy ...............................................83
Side section ........................................81
Sunbed base ......................................79
V
Voice Guide.................................................52
Voltage ........................................................61
Volume ........................................................55
109
Index
I
Intended use ............................................... 10
Interior lighting, replacing............................ 85
Interrupting tanning session........................ 30
Warranty
JK-Products, Inc. – Limited Warranty
JK-Products, Inc. warrants its products to be free from defects in materials and workmanship under intended normal use as described in the
unit's Operation and Instruction Manual, for a period of three (3) years
from date of sale.
This Limited Warranty applies only to the original purchaser of the equipment through JK-Products, Inc. or its authorized dealer or distributor, and
is not transferable.
Global Service USA obligations under this warranty are limited to repair
or replacement of any defective part without charge for that part to the
original purchaser, with the following exceptions:
A Fluorescent lamps are warranted against defects for a period of thirty
(30) days from date of sale.
Limited warranty
B Only parts obtained through JK-Products, Inc., its authorized dealers
or distributors may be used. Transportation costs for parts shipped to
the consumer and the return of defective parts to Global Service USA
are not included.
C Labor will be furnished without charge for ninety (90) days from date
of purchase only. All labor and related charges must be authorized by
Global Service USA prior to start of repairs, and must coincide with
Global Service USA established rates and time allotment policy.
D Acrylic: Refer to Manufacturer's Acrylic Warranty Policy.
It is imperative that the original customer completes and returns the enclosed warranty card within 10 days after purchase to insure valid registration and coverage for potential claims.
110
If the warranty card is not registered, proof of purchase from JK-Products, Inc. or its authorized dealer or distributor will be required prior to any
consideration on warranty claims. This could result in service delays.
This warranty is extended to the individual or legal entity, whose name
appears on the warranty registration card filed with Global Service USA,
or whose name appears on the original sale document and may not be
transferred to any other individual or legal entity.
This warranty does not apply to any failure of the product, or any parts of
the product due to alterations, modifications, misuse, abuse, accident,
improper maintenance, improper installation, acts of God or if the serial
number on the product has been removed, altered or defaced. Adequate
packaging must be used for returned goods to prevent freight damage.
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
of merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
No person, firm or corporation is authorized to obligate JK-Products, Inc.
for any liability in connection with the sale or use of these goods.
Warranty
Limited Acrylic Warranty
JK Products, Inc. warrants its acrylic sheets to be free from defects in material and workmanship, under intended normal use, for a period of one
(1) year from date of sale of the tanning bed. Due to the tanning lotions,
cosmetics, disinfectant and improper cleaners used on tanning surfaces
that cannot be controlled by JK Products, Inc., after the first thirty (30)
days of warranty period acrylic will be subject to a prorated cost to the
consumer.
JK Products, Inc. obligations do not include transportation charges on replacement acrylic.
JK Products, Inc. assumes no liability for the cost of removing defective
sheets or installing replacement sheets, nor for damage to persons or
property.
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
To make a claim, contact an authorized dealer or distributor of JK-Products, Inc. or Global Service USA with the model number, the serial number, and the date of purchase of the bed in which the acrylic will be used.
Limited warranty
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
111
Warranty
Warranty Claims
Policy & Procedures
1. When to file a Warranty Claim:
In the event that your tanning system is not functioning properly under intended normal use as described in the unit's Operation an Instruction
Manual, you may then have established cause to file a Warranty Claim.
NOTE:
Both the tanning system and legal registered owner must
meet the criteria established under JK Products, Inc. Limited Warranty as described in this manual before any Warranty Claim will be considered.
2. Where to call to place a Warranty Claim:
Warranty Claims
JK-Products, Inc. is supported nationwide by an extensive dealer/distributor network through whom the majority of our units are sold. These dealers/distributors are required by contract to stock sufficient parts to meet
the various warranty and nonwarranty needs of their customers.
Therefore, in order for you to properly file a Warranty Claim, you must locate the name and phone number of the dealer/distributor through whom
you purchased your unit. Normally this information can be easily located
either on your paid invoice or other proof of purchase documentation that
you received when taking delivery of the unit.
Next, notify the dealer/distributor of the serial number, model number and
date unit was purchased. This will initiate the Warranty Claim process.
112
Upon determination of the problem, your dealer/distributor can then supply you with the part(s) and proper instructions to return your unit to working order.
Each dealer/distributor has their own internal procedure for handling
Warranty Claims and credits.
NOTE:
JK-Products, Inc., the manufacturer, does not involve itself
in the direct handling of a Warranty Claim except where mitigating circumstances apply and where required by law.
NOTE:
If part returned to Global Service USA proves to be operational and not defective, or if product code numbers on part
do not correspond with individual unit date on file with Global Service USA, then a 30% restocking fee will be charged
in addition to the retail purchase price of part.
Acknowledgment of the Agreement is not required for acceptance of the
foregoing stipulations.
Labor Warranty Claim/Credit Procedures
Global Service USA furnishes labor without charge for a period of 90
days from date of purchase. All labor and related charges must be authorized by Global Service USA prior to start or repairs, and must coincide
with Global Service USA established rates and time allotment policy.
Please contact our Service Department for authorization and billing procedures.
Warranty
Global Service USA warrants specific individual components of the tanning system against defects in materials and workmanship for the life of
the product. Coverage is limited to units purchased after November 1,
1994.
This warranty is restricted by the following components only:
• Steel Back Panels
• Structural Steel Frame Components
• Exterior Steel Body.
NOTE:
Components are warranted on an individual basis and not
as they may effect the complete product.
Warranty coverage does not include cosmetic abnormalities such as
scratches, nicks, dents, rust, oxidation of paint or other cosmetic changes that do not interfere with the designed function of the unit.
This warranty does not include failure of the product due to alteration,
modifications, misuse, abuse, improper maintenance, improper installation or repair.
fective components of the manufacturer. All freight charges must be paid
by the customer.
There are no warranties which extend beyond the description on the face
hereof. There is no express or implied warranty of fitness or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are provided
in substitution of all other remedies. Consequential and incidental damages are excluded.
NOTE:
Any misuse, abuse, modification, alteration, improper maintenance, improper installation, etc. of this product or its intended use will subject said party to direct responsibility and
liabilities for any and all consequences resulting from such
action. Furthermore, such actions will void all warranties
and may relieve Global Service USA of any liabilities relating to said product.
Warranty Claims
Limited Lifetime Warranty
This warranty is not transferable and is only applicable to the original purchaser named on a completed and registered warranty record at JKProducts, Inc. headquarters.
JK Products, Inc. obligations do not include transportation charged on
the shipping of new components to the customer or on the return of de-
113
Appendix
Troubleshooting
In the case of a fault, a fault code1) appears on the display to simplify localizing of the fault cause:
• If a fault occurs, the fault code flashes in the display.
• If several faults occur, the fault messages are displayed alternately.
• The fault remedy is acknowledged by pressing the
If the fault cannot be eliminated, contact Customer Service:
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
(800) 445-0624
(870) 935-9046
e-mail: support@jkamerica.com
Appendix
http://support.jkamerica.com
1) see separate instructions “Error codes”, Order no. 800 751
114
button.
1002479_00_TB_Esprit_USA_070906.qxd
06.09.2007
10:46 Uhr
Seite 1
1002479
ESPRIT 770
OPERATING INSTRUCTIONS
SUN ERGOLINE, A DIVISION OF JK-PRODUCTS & SERVICES, INC.
1 Walter Kratz Drive . Jonesboro, AR 72401
Phone: 800.643.0086 (Toll-free) · Email: ergoline@sunergoline.com
Fax: 870.935.3618 · Website: www.sunergoline.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising