Features • Premium CREE XP-L HI V3 LED • Maximum output of

Features • Premium CREE XP-L HI V3 LED • Maximum output of
Features
• Premium CREE XP-L HI V3 LED
• Maximum output of 1100 lumens
• Max beam distance up to 257 meters
• High efficiency circuit provides runtime up to 192 hours
• Intelligent charging circuit with voltage detection charges safely and rapidly
• USB rechargeable, onboard USB charging port is water, dust and impact resistant
• Intelligent memory function stores preferred brightness setting
• Broad voltage circuit accepts both rechargeable and non-rechargeable Lithium batteries
• Optimized ultra-precise reflector offers a longer beam distance than competing products
• Waterproof in accordance with IPX-8 (submersible to two meters)
• Toughened ultra-clear mineral glass with anti-reflective coating
• Constructed from aerospace-grade aluminum alloy 6061-T6
• HAIII military grade hard-anodized
• Reverse polarity protection
• Stainless steel titanium-plated clip
• Anti-rolling design
Dimensions
Length: 140mm (5.51”)
Head Diameter: 25mm (0.98”)
Tail Diameter: 24.2mm (0.95”)
Weight: 75.5grams (2.66oz)(without battery)
Accessories
Rofis 18650 Li-ion battery(3400mAh) ×1
Holster ×1
USB cable ×1
Lanyard ×1
Spare O-ring ×2
Spare USB port cover ×1
Clip ×1
Battery Options
Battery
Type
Nominal voltage
Compatible
The protected 18650 Rechargeable
Li-ion battery
18650
3.6V
Yes (Compatible and can be
recharged)
Primary Lithium battery
CR123
3V
Yes (Compatible but can NOT
be recharged)
Rechargeable Li-ion battery
RCR123
3.7V
Yes (Compatible but can NOT
be recharged)
*Warning: Charge protected 18650 rechargeable Li-ion batteries only, do not attempt to charge
non-rechargeable batteries, CR123 or RCR123 batteries.
Brightness & Runtime
Mode
Specification
Strobe/
Moon
Ultra-low
Low
Medium
High
Turbo
Beacon
/SOS
ANSI lumens
(LM)(1*18650)
Runtime(h)
(1*18650)
5
14
65
160
350
1100
192
112
31
11.5
4.5
1.7
1100
Peak beam
intensity (candela
16528cd
units)
Max beam
distance(m)
Impact
resistance(m)
Waterproof
257m
1.5m
IPX8(under water 2m)
NOTICE
Stated data has been measured according to the international flashlight testing standards ANSI/NEMA
FL1 using a quality 1×Rofis 18650(3400mAh 3.6V) battery under laboratory conditions. The data may
vary due to individual usage habits and environmental conditions.
Operation instructions
Battery Installation
1. Unscrew the tail cap in counter-clockwise direction.
2. Insert one 18650 battery or two CR123 batteries with the positive pole pointing forward
(toward the light head).
NOTE: Ensure batteries are inserted with the positive (+) end pointing to the head. The KR10 will
not operate with incorrectly inserted batteries.
Tactical Setting
1. Momentary Illumination: Momentary illumination mode is accessed by pressing the tail
switch partway down and holding with the flashlight in standby. Release the switch to turn
the light off (The flashlight will return to memorized mode when next turned on).
2. Tactical Strode: When light off, lightly pressing the tail switch partway down twice in
succession to activate strobe mode, release the switch to turn the light off, long depress to
keep strobe.
3. To switch ON: Press the button on the tailcap until a “click” is heard, the flashlight on and
keep the brightness level last used (The brightness level mode has memory function to
memorize the mode last used).
4. To switch OFF: Press the button on the tailcap a second time until a “click” is heard, the
flashlight off.
Outdoor Setting
1. Switching ON/OFF
To switch ON: Press the tailcap switch until a “click” is heard.
To switch OFF: Press the tailcap switch a second time until a “click” is heard.
2. General Operations
Brightness Level: With the light turned on, press the mode switch repeatedly to cycle through
brightness levels of ultra-low, low, medium, high and turbo. This mode has memory effect ensure
direct access to the brightness level last used.
3. Special Modes
Strobe/Location Beacon/SOS mode: With the light turned on, press and hold the side switch
for over one second to activate Strobe mode. Press and hold once again to access Location
Beacon mode and repeat once more for SOS mode.
Moon mode: First to press the side switch and press the tailcap switch to activate and keep
moon mode.
Positioning function
With the light turned on, press the mode switch repeatedly to cycle through brightness levels of
ultra-low, low, medium, high and turbo, then press the mode switch to activate the positioning
function, with the light off, the green power indicator to blink twice every three seconds.
Power Tips
After the light turned on or switched the mode(the special modes are excluding) 3 seconds, the
power indicator built into the switch will illuminate 3 seconds to indicate remaining battery
power:
The green power indicator will illuminates when battery power is over 50%.
The red power indicator will illuminates when battery power is less than 50%.
The red power indicator will blink quickly when battery power is going to run out. Please charge
or replace the battery as soon as possible.
Charging Function
Caution: The KR10 needs to be turned on in order to enter charging mode.
The KR10 is capable of charging a protected 18650 Li-ion battery via the included USB cable.
Simply install a protected 18650 Li-ion cell, plugging one end of the USB cable into the flashlight
and the other end into a universal USB port / adaptor and the KR10 will take care of the rest.
Charging indicator light
1. Connect the charging cable to the flashlight and the A/C power adapter to the wall outlet. Fully
charging a depleted 18650 battery takes approximately 6 hours.
2. Under normal charging conditions, the green indicator light near the charging port will blink
twice every three seconds.
3. During charge: The indicator light on the switch is red.
Charging is complete: The indicator turns green(To prevents excessive charging the charger
should stops charging when the indicator turns green).
Changing / Charging Battery
Batteries should be replaced or recharged when output appears to be dim or the flashlight
becomes unresponsive.
Maintenance
Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of
silicon-based lubricant.
Warranty Details
Our authorized dealers and distributors are responsible for warranty service. Should any problem
covered under warranty occurs, customers can contact their dealers or distributors in regards to
their warranty claims, as long as the product was purchased from an authorized dealer or
distributor. ROFIS’s Warranty is provided only for products purchased from an authorized source.
This applies to all ROFIS products. Any DOA / defective product can be exchanged for a
replacement through a local distributor/dealer within the 15 days of purchase. After 15 days, all
defective / malfunctioning ROFIS® products can be repaired free of charge for a period of 60
months (5 years) from the date of purchase. Beyond 60 months (5 years), a limited warranty
applies, covering the cost of labor and maintenance, but not the cost of accessories or
replacement parts. The warranty is nullified if the product(s) is/are broken down, reconstructed
and/or modified by unauthorized parties, or damaged by batteries leakage. For the latest
information on ROFIS® products and services, please contact a local ROFIS® distributor or send an
email to rofisinfo@rofislight.com
※All images, text and statements specified herein this user manual are for reference purpose
only. Should any discrepancy occurs between this manual and information specified on
www.rofislight.com information on our official website shall prevail. Rofis Technology Co., Ltd.
reserves the rights to interpret and amend the content of this document at any time without
prior notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising