EFXPW= Wall Bracket Mount TYPE: CATALOG #: NOTES: INDUSTRIAL EFXP Series Explosion-Proof Remote Exit Signs Standard Features • Available with 6, 12 and 24 volt lamps for DC operation or 120 volt AC fixtures • Exits shown are explosion-proof fixtures of heavy cast aluminum construction with Pyrex® lenses. Exit housing is an 18 gauge fabricated steel box with a baked enamel finish. Stenciled exit lettering is available on one or two faces. All EFXP Series have extra large downlight openings • EFXP units are designed for mounting in locations that are remote from the power source. If the power source is installed outside hazardous areas, the length of the connection wires should be carefully considered to ensure that the voltage of the emergency power unit and the wire size of the connecting circuit are adequate to offset the voltage drop in the circuit • Sealed test switch • Complies with NEC, OSHA and NEMA specifications for the following Classes and Groups: Class I, Division 1 & 2, Groups C & D (300W PS-25 max) Class II, Division 1 & 2, Groups E, F & G (60W max) Class III, Division 1 & 2 (150W max) UL924 Listed for use in Paint Spray Areas (75W max) Suitable for Wet Locations • 3-year limited warranty Detailed warranty terms located at: www.emergi-lite.com/usa/files/EL_Warranty.pdf EFXPP= Adjustable Pendant Mount EFXPC= Ceiling Mount Dimensions Dimensions are approximate and subject to change. AC-Only and AC/DC Exit Signs 6” 6”cm] [15.24 9-1/8” 9-1/8” 23.17 cm] 16-7/8” 16-7/8” [42.86 cm] 17-3/4” 17-3/4” [45.08 cm] Pyrex® is a registered trademark of Corning Glass. Output Voltage: Must be identical to DC Input Voltage 23-3/8” [59.2 cm] 30-5/8” [77.8 cm] 30-5/8” 23-3/4” Lamp Selection Lamp Type Unit Warranty* Entire unit (excluding lamps) carries a 3-year Full Warranty. Quartz Bi-Pin *Subject to proper installation and maintenance. Medium Base Power Consumption Chart 120/277VAC, 60Hz maximum 0.3/0.15A LED Lamp, Red How to Order SERIES 20-1/8” [51.0 cm] 23-3/4” [60.4 cm] Wattage: Panel oversized 10-20% greater than total connected load. EFXP= Exit series 23-3/8” To Lighting Loads AC - Normal Operation DC - Emergency Operation 20-1/8” TS Transfer Panel Output Input Voltage: From AC - 120 Volt, 60Hz, 1 phase (other voltages available). From DC - 6, 12, 24 or 120 Volt (select). 16-7/8” 16-7/8” [42.86 cm] Combination Units 23-3/4” Electrical Specifications for Transfer Panel Self-Powered Exit Sign DC Output 34-1/8” 34-1/8” [86.67 cm] 17” 17” [43.18 cm] Emergency Lighting Unit AC Input assigned to same breaker and/or phase 23-3/4” [60.4 cm] The transfer circuit is not designed for use in hazardous or explosive areas. The transfer circuit is to be mounted remotely from hazardous areas. 6” 6”cm] [15.24 12-3/8” 12-3/8” [31.43 cm] 12-3/8” 12-3/8” [31.43 cm] Mounting Pendant Mount Wall Mount Ceiling Mount 5-3/4” 5-3/4” [14.6 cm] MOUTING C= Ceiling mount P= Pendant W= Wall Voltage Lamp Type Suffix 6V 15W JC-6V15W 2,000 XX6 25W 25A-12 1,000 XX12 24V 25W 143A 1,000 XX24 120V 25W A19 2,500 AC/20 120V 5W – 100,000 XX120 # OF FACES AC120= 120V-25W (AC only) XX120= 120V-5W LED Average Life (hours) 12V LAMP TYPE XX6= 6V-15W (DC only) XX12= 12V-25W (DC only) XX24= 24V-25W (DC only) Power 1= Single face 2= Double face 3= Triple face LETTERS -R= Red -G= Green Example: EFXPC(XX6)-2R AC VOLTAGE 120= 120VAC 277= 277VAC DC VOLTAGE -6= 6VDC -12= 12VDC -24= 24VDC SERIES -TS= Transfer circuit LOAD WATTAGE -25= 25W -50= 50W -75= 75W -100= 100W Example: 120-6-TS-25 All information and specifications contained in this specsheet are subject to change due to engineer design, errors and omissions. Illustrations and diagrams within this specsheet may vary from actual products. 2016© Thomas & Betts Limited. All rights reserved.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project