Product Catalogue - Platform lifts

Product Catalogue - Platform lifts
Product catalogue
Aritco Platform Lifts
Aritco 7000, Aritco 9000
2015
Aritco Platform Lifts
-accessibility lifts for all needs.
This catalogue is primarily made for all our partners
around the world. The purpose is to show what
Aritco can offer in terms of products, options and
possible combinations.
Product summary.................................................. 4
Carrier.................................................................... 6
Landing door.......................................................... 22
Shaft....................................................................... 34
Communication..................................................... 38
Drive....................................................................... 39
Outdoor execution................................................ 40
Flexi........................................................................ 42
Drawings................................................................ 4 4
FAQ......................................................................... 54
Features and benefits........................................... 57
Order information................................................. 58
Overview of the lifts.............................................. 59
Due to continuous product development, specifications are
subject to change without notice. With reservations for misprint
and articles out of stock.
Product summary - Aritco 7000
Aritco 7000
- our bestselling platform lift
The lift is designed to meet all requirements for quality, safety and service
life. It is a perfect fit for tough and demanding environments such as
schools, shops and residential buildings.
Aritco 7000
Technical compliance:
European Machine directive 2006/42/EC
European standard EN 81-41
Lift type:
Platform lift
Drive system:
Patented screw/nut system
Rated speed (max):
0,15 m/s
Travel height:
1)
Number of stops:
Max. 6 stops per lift
Number of doors:
Max. 6 doors per lift
Number of doors per
floor:
Max. 2 doors per floor
Pit:
50 mm (no pit is required when there is a ramp)
Entry:
One, two or three sides
Top height:
Minimum 2240 mm
(1100-1600 mm with half height door)
Platform control:
”Hold to run”, the destination button must be
kept pressed down during the whole ride
Landing control (on
door):
One-touch call
Environment:
Indoor/outdoor
Emergency lowering:
Battery operated emergency lowering
Control voltage:
24V
Motor:
2,2kW
Power supply:
1-phase 230V 50 Hz/9 A/16 A slow
3-phase 230V 50 Hz/9 A/16 A slow
3-phase 400V 50 Hz/5.2 A/16 A slow
Rated load:
250, 410 or 500 kg (depending on platform size)
250 -13 0001) mm
Travel height when having a half door is maximum 3 000
mm (inside EU)
Platform
Aritco 7000 is available in 8 different platform sizes. The rated load
depends on the platform size.
Platform floor
area A/C x B
(mm)
Load
(kg)
900 x 1040
250
900 x 1280
410
900 x 1480
410, 500
1000 x 1280
410
Load limits
per power supply
400V
3-phase
50Hz
400V
3-phase
60Hz
230V
3-phase
50Hz
230V
3-phase
60Hz
230V
1-phase
50/60Hz
250 kg
1000 x 1480
410, 500
l
l
l
l
l
410 kg
1000 x 1980
500
l
l
l
l
l
500 kg
1100 x 1480
410, 500
l
1100 x 1580
500
l
4
Product summary - Aritco 9000
Aritco 9000
- our platform lift with cabin
Aritco 9000 is our cabin lift for the accessibility market. The lift is
designed to meet all requirement for quality, safety and service.
It is a perfect fit for tough and demanding environments such as
schools, shops and residential buildings.
Aritco 9000
Technical compliance:
European Machine directive 2006/42/EC
Lift type:
Cabin lift
Drive system:
Patented screw/nut system
Rated speed (max):
0,15 m/s
21501) -13 000 mm
Travel height:
1)
Opposite entry: min 2 150 mm
Single entry : 2 300 mm for 2000 mm door opening
height
Number of stops:
Max. 6 stops per lift
Number of landing
doors:
Max. 6 doors per lift
Pit:
75 mm (no pit is required when there is
a ramp)
Entry:
Single entry: A, B or C-side
Opposite: A and C-side
Top height:
Minimum 2400 mm
Cabin control:
Automatic ”one-touch” with cabin doors
Landing control (on
door):
One-touch call
Environment:
Indoor
Emergency lowering:
Battery operated emergency lowering
Control voltage:
24V
Motor:
3 kW
Power supply:
3-phase 400V 50 Hz/5.2 A/16 A slow
Rated load:
400 kg
Cabin
Aritco 9000 is available in 2 different cabin sizes (cabin floor area).
Cabin floor area
A/C xB (mm)
Max load
(kg)
Power supply
1000 x 1400
400
400 V 3-phase
1100 x 1400
400
400 V 3-phase
Frequency 50 or 60 Hz.
5
Carrier
Aritco 7000, Aritco 9000
6
Carrier - Aritco 7000
Platform
Half height wall
The platform is in its basic execution delivered with a side wall
(half height) including the destination panel. Panels under the
destination panel are painted in RAL 7042 (grey) as standard,
but can be painted in any RAL colour as an option.
Height 1100 mm.
C
D
B
A
A,B,C and D-side of platform.
Full height wall
As an option the platform can be delivered with a full height wall
(2100 mm high) with a mirror.
The full height wall is in RAL 7042 (grey) as standard, but can be
painted in any RAL colour as an option.
The full height wall is available for D-side of 1480 mm, i.e for platform sizes 900x1480 mm, 1000x1480 mm and 1100x1480 mm.
Note also that full height wall is not possible if you have a lower
door opening height than 2000 mm or having a half height door.
Fold down seat
In solid birch and with chromed brackets. The seat
has to be folded back manually after use.
Can be ordered as an option.
Size: 320 x 400 mm
Not available for 900x1040.
7
Overview Aritco 7000
900 x 1040
900 x 1280
%
900 x 1480
â
â
ø
%
1000 x 1280
â
ø%
1000 x 1480
1000 x 1980
ø%
1100 x 1480
For more detailed drawings see page 44.
ø%
"%
1100 x 1580
8
9
Carrier - Aritco 7000
Destination panel
The destination panel is always placed on the machine side (D-side) of the
platform. It contains the destination buttons, emergency stop, alarm button,
autodialer (option), landing indicator (option), Aritco logo, max weight and
number of persons allowed.
All text and logos are screen printed to ensure good quality. The location of
the platform buttons and the handrail are according to E81-41.
• Anodized aluminium - standard
• Stainless steel - option
Destination buttons
Faceplate panel
The faceplate panel is painted in grey, anodic
color Natura which has an Aluminum look.
To prevent any trapping, a safety list is mounted
behind the faceplate panel which cuts off the
security circuit when pressed down.
Destination buttons are according to EN 81-41 and EN81-70
for disabled. The location of the buttons are within the
limits in the standard, i.e. height between platform floor and
the center line of the buttons is between 900-1100 mm.
Standard buttons are engraved with braille. The buttons are
of polycarbonate plastic. Following buttons are available:
-2, -1, 0, 1, 2, 3, 4, 5, 6, B, BG, BV, G, K, KV, P, U, E. Individual
special characters can also be ordered as an option.
Maximum 2 characters per button. These buttons will also
be engraved. If a lift is ordered with any button that is not 0,
1, 2, 3 all buttons will be engraved.
42
44 131-0
44 131-1
44 131-2
44 131-3
44 131-ALARM
31
67
Active area 2800 mm2
0.5 mm braille
0.8 mm relief
Braille and relief profile for best
tactile feeling
Black/white for best contrast
Polycarbonate plastic
Alarm button
A standard alarm button is always
delivered with the lift. When it is
pressed a buzzer sounds. This is only
a signal to the user that the button
is pressed. The alarm button may
be connected to an external alarm
sounder or an autodialer.
Buttons 0, 1, 2, 3 can also be molded with braille.
The buttons are of anodized aluminum with
2- component paint. If a lift is ordered with only
buttons 0, 1, 2, 3 molded buttons will be delivered.
42
44 131-xx-F
0.8 mm relief
31
67
Active area 2800 mm2
0.5 mm braille
Anodized aluminum with
2-component paint
External alarm sounder
External alarm sounder mounted outside
the lift. It is connected to the alarm button
and when the alarm button is pressed the
external alarm sounder will give a loud
signal outside the lift to attract attention in
case of emergency.
Can be ordered as an option.
Handrail
A handrail is mandatory according to EN81-41
and delivered as a standard. Height of handrail
is 875 mm from the platform floor. Handrail
diameter is 36 mm. The ends of the handrail
are closed and turned the platform.
• Anodized aluminum (standard)
• Stainless steel (option)
10
Light
LED lights are installed over
the destination panel.
Remote control for operation of platform
A remote control is connected to the destination buttons on the platform. Instead of pressing the destination button on the platform the button on the
remote control can be pressed (hold to run). Remote control with 2 to 6 buttons, with
numbers 2-6. One remote control per lift. One receiver per two floors.
Can be ordered as an option.
Emergency stop button
Button in “mushroom” type for
emergency situations.
Is always included as standard.
ASSA
Landing indicator
Telemecanique
Digital display positioned at the destination panel. It
shows which floor the lift is on at the moment. The
indicator can also be fitted with a voice announcer
available in Danish, Dutch, English, Finnish, French,
German, Norwegian, Polish, Russian and Swedish.
Voice: Basement, Ground floor, Floor 1-6
Key switch on platform
Key switch placed on destination panel. The key switch locks
the platform functions and prohibits unauthorized use. One
key switch per platform can be provided. The key switch
can be serial connected to all destination buttons or the key
switch is connected to one destination button.
The landing indicator can also show information from
the system.
•Warning if the batteries are low.
Two brands to choose from:
• ASSA (Nordic markets only). Aritco only delivers the
housing, Aritco does not deliver the locking cylinder.
• Telemecanique
•A bell when the alarm button has been pressed.
•Number of starts and total run time since installation
or since last reset.
•A weight symbol will appear if the lift is overloaded.
Can be ordered as option.
•If connected to the buildings fire alarm a “Fire”
symbol will be shown when alarm is activated.
Can be ordered as an option.
11
Carrier - Aritco 9000
Cabin
The cabin is a light weight cabin made of wood and the walls are covered with laminate. The height of the cabin (floor to roof) is 2100 mm.
Destination panel
The destination panel is placed on the machine side (D-side) of the cabin.
Mirror
Mirrors on the machine side (D-side, same side as destination panel) can be
ordered as an option. Two mirrors will then be delivered, one on each side of the
destination panel. As an option it is also possible to order a mirror on the A or C
side (on the opposite side of the door). This will help a wheelchair user who can´t
turn around to observe obstacles behind them when moving backwards out of the
cabin. When a mirror is ordered on A or C side a handrail on this side is mandatory
to prevent the mirror to get damaged. The handrail on A or C side is connected to
the handrail on the D-side with a bend.
Handrail
As standard the cabin comes with a handrail on the machine side (D-side) in stainless
steel. The diameter of the handrail is 32 mm and it is placed/mounted 890 mm
above the cabin floor. The handrail has a straight shape and goes along the machine
side. It ends with a black plastic plug. Handrail brackets (fixings to the wall) made in
brushed stainless steel are delivered with the handrail.
As an option the handrail can be delivered in oak. The handrail in oak has a diamater
of 38 mm. The handrail bracket (fixings to the wall) are in stainless steel as when
ordering a stainess steel handrail.
Panel for lift information
A plate in stainless steel is placed on the machine side of the lift. On the panel
the CE -marking is placed. Extra space is also available for other liftinformation
of your choice.
Bump rail
To protect the cabin from getting damaged
when using it for goods bump rails in brushed
stainless steel can be ordered as an option.
The bump rail is a rectangualar tube mounted
on the walls where there are no doors/openings in the cabin. The stainless steel bump
rail ends with black plastic ends. The size of
the bump rails is 20x60 mm. The bump rails
can also be delivered in solid oak, 70x20 mm.
Kick plate
Kick plate protecting the bottom part of the cabin. Surface mounted polished stainless steel 100 mm high. Delivered as standard.
12
Cabin ceiling
Standard cabin ceiling laminate is white grey (same laminate as used as standard for cabin walls, for
all sides except for machine side). The celing always comes with four white LED spotlights (each LED
with 3x1W, warm white). The LEDs comes with a dimmer (placed on roof) which allows you to set
the brightness of the LED lights.
Emergency light (Diod, 1 W, white) is also installed in the cabin roof as standard. The emergency
lights is only lit when there is a power failure. Illuminates the cabin panel.
Cabin walls
Standard wall laminate for machine side is black with small embossed dots. For the other walls,
where there are no doors standard laminate is white grey. As an option you can chose from a range
of different laminates in different colours. Choose the same colour for all cabin walls or choose
one colour for the machine side and another colour for the remaining walls. Not valid for option
Stainless steel plates 1 mm.
Standard for other sides than machin side:
Standard for machine side:
Black embossed dots
White grey
Options:
Light green
Orange
Red
Purple
White grey
White beige
Grey
Turquoise
Blue
Navy blue
Light grey city plan
pattern
Dark grey city plan
pattern
White stained wood
Birch
Light oak
Oak
Walnut
White embossed dots
Black embossed dots
Silver (looks like polished
steel)
Stainless steel plates
1 mm
13
Stainless steel metal foil
(polished appearance)
Carrier - Aritco 9000
Destination panel
The destination panel is placed on the machine side (D-side) of the cabin. It contains the destination buttons, alarm button, autodialer (option), landing indicator
(option), door ”re-open” button, door close button, Aritco logo, max weight and
number of persons allowed. The cabin panel is made of stainless steel.
Destination buttons
Destination buttons are according to EN81-70 and EN81-41 for disabled.
The locations of the buttons are within the limits in the standard, i.e. height
between cabin floor and the center line of the buttons is within 1000-1200 mm.
1600 - 1800 mm
Buttons are square 28x28 mm. It is a stainless steel touch plate with black background and signs in stainless steel. Signs and braille are embossing (brightened).
Height of signs is 15 mm. The button comes with a background lit frame which
indicates if the destination button is pressed.
Following buttons are available: -2, -1, 0, 1, 2, 3, 4, 5, 6, B, G, K, P, U, E.
15 mm
“Re-open button” and “door close buttons”
Max 1200 mm
1000 mm
970 mm
“Re-open button” and “door close button” according to EN81-70 are included as standard.
Re-open button: identified by the symbol < I >
Close button : identified by the symbol > I <
14
Landing indicator
Remote control for operation of carrier
A remote control is connected to the destination buttons
on the platform. Instead of pressing the destination button
on the platform the button on the remote control can be
pressed (hold to run).
Remote control with 2 to 6 buttons, with numbers 2-6.
One remote control per lift. One receiver per two floors.
Can be ordered as an option.
Digital display positioned at the destination panel. It shows which
floor the lift is on at the moment. The indicator can also be
fitted with a voice announcer available in Danish, Dutch, English,
Finnish, French, German, Norwegian, Polish, Russian and Swedish.
Voice: Basement, Ground floor, Floor 1-6
The landing indicator can also show information from the system.
• Warning if the batteries are low.
• A bell when the alarm button has been pressed.
• Number of starts and total run time since installation or since
last reset.
• A weight symbol will appear if the lift is overloaded.
• If connected to the buildings fire alarm a “Fire” symbol will be
shown when alarm is activated.
Can be ordered as an option.
External alarm sounder
External alarm sounder mounted outside the lift. It is
connected to the alarm button and when the alarm
button is pressed the external alarm sounder will give
a loud signal outside the lift to attract attention in
case of emergency.
Can be ordered as an option.
ASSA
Telemecanique
Key switch on carrier
Key switch placed on destination panel. The key switch locks
the platform functions and prohibits unauthorized use. One
key switch per platform can be provided. The key switch
can be serial connected to all destination buttons or the key
switch is connected to one destination button.
Two brands to choose from:
• ASSA (Nordic markets only). Aritco only delivers the
housing, Aritco does not deliver the locking cylinder.
• Telemecanique
Alarm button
Can be ordered as option.
A standard alarm button is always delivered with the
lift. When it is pressed a buzzer sounds. This is only
a signal to the user that the button is pressed. The
alarm button may be connected to an external alarm
sounder or an autodialer.
15
Carrier - Aritco 9000
Cabin doors
The cabin will be delivered with cabin doors. The cabin doors will be automatic folding doors, bus-type.
Doors can be installed on A, B or C side or both A and C side.
Landing doors (installed in shaft) will always have door opening width 900 mm, independently of which
side of the shaft the door is installed. The standard opening height of the landing door is 2000 mm. As
option landing doors can be delivered with opening height 1800 and 1900 mm.
The opening height of the cabin folding door is always 2000 mm (independently of the landing door
opening height). The door width of the cabin folding door depends on which side of the cabin the door
is installed and on the size of the cabin. For A- and C-side 1100 mm and B-side 1400 mm the folding
door is 950 mm wide. The cabin folding door is made a little bit wider than the landing door, that is
900 mm wide. This is to reduce the risk of having the folding door damaged. On A/C side of the 1000
mm cabin there is no place to make the cabin door wider than 900 mm.
There are two options to choose from:
• Vision panel – steel door with small vision panels
• Aluminum profile - aluminum door with big vision panels
A/C side
Aluminum profile
B-side
Cabin size (mm)
1000
1100
1400
Cabin folding door width (mm)
900
950
950
Landing door width (mm)
900
900
900
Vision panel
Overview Aritco 9000
1000x1400
1100x1400
ø
ø
For more detailed drawings see page 52.
16
17
Carrier - Aritco 9000
D
Cabin entry
A
C
Aritco 9000 can be delivered with single entry or opposite entry.
B
Single entry: with one cabin door and all landing doors on the
same side of the shaft;
• A – side or,
• B – side or,
• C – side
Opposite entry: with two cabin doors and landing doors on two
sides of the shaft;
• A and C - side
Roof height on bottom floor and service hatch
For cabins with opposite entry (landing door and cabin door on both A and C side) the following is valid:
• For sides where you have only one landing door and the landing door is placed on the bottom floor, a
service hatch is mandatory over the landing door so that you can reach the door machinery on the cabin
door. This service hatch is placed on top of the landing door frame, which leads to that the minimum floor
height on the bottom floor is 2532 mm (without a pit) and 2457 mm (with a pit). On other floors than the
bottom floor there will be no need for a service hatch. Note that on these lifts it is not possible to have a
fire proof door, EI60 door, on sides where you only have one door and this door is placed on the bottom
floor. This is since the service hatch is not fire proof.
• For sides where you have more than one landing door there will be no need for a service hatch, since the
door machinery of the cabin door can be reached from above landing door.
Travel height
Travel height: 2 150*-13 000 mm.
Minimum travel height:
•*2 150 mm when not having landing doors on the same side. E.g. When having opposite entry A and
C side. The minimum travel height is due to the fact that you need to get up on the cabin roof to make
service.
•*2300 mm when having landing doors on the same side. E.g. when having two doors on the same side;
A, B or C side. Due to the height of the door frame and threshold on the landing doors.
18
19
Carrier - Aritco 7000 and Aritco 9000
Flooring
Choose between the following options for vinyl, rubber and aluminum floorings:
Standard:
Beige
Vinyl
Blue
Vinyl
Sand
Vinyl
Grey
Vinyl
European oak
Vinyl
Classic Beech
Vinyl
20
Option:
Checker Stud – Blue
Rubber
Checker Stud – Black
Rubber
*Aluminum flooring is not available for Aritco 7000 platform 900x1040 mm or for Aritco 9000.
21
Aluminum*
s possible
News. New door profileur.
to paint in any RAL-colo
Landing door
Aritco 7000, Aritco 9000
22
Door
Landing door - Aritco 7000 and Aritco 9000
General information
The landing doors installed at each landing are made of toughened
galvanized steel and laminated and toughened glass, 8 mm thick.
All doors are painted in RAL 9003 (Aritco white) but can be painted in any
RAL colour as an option. The door frame and door blade can be painted
in same colour or the frame in one colour and the blade in another
colour. For the same lift all doors must be painted in the same colour.
A glassed area according to EN81-41 is standard for all doors. Standard is
with clear glass (JT0). Optional is to have tinted (JT16), dark tinted (JT5)
or frosted glass (JT23).
The profiles around the glass are made of aluminium. The profiles can be
painted in any RAL colour. If the door blade is in RAL 9003 (Aritco white)
the profiles can be painted in the same colour as an option. If the door
blade is painted in another RAL colour, the profiles will be in aluminium
as standard, but can be painted in the same RAL colour as the door blade
as an option. Note that aluminium profiles are standard and that painted
profiles are an option.
All doors can be left- or right hinged. Doors are always delivered with
door frame. It is not possible to order the door or the frame separately.
Large glass door
Large glass door with one glass window.
Opening widths: • Aritco 7000: 800, 900, 1000 mm
• Aritco 9000: 900 mm
Opening heights:
• Aritco 7000: • Aritco 9000: 1800, 1900, 2000, 2100 mm
1800, 1900, 2000 mm
The actual height of the door is 40 mm higher since a plate that covers the joint between the door and the frame is mounted on the door.
Glass window (vision):
• Aritco 7000: 612x1472 mm (800 mm wide door)
712x1472 mm (900 mm wide door)
812x1472 mm (1000 mm wide door)
• Aritco 9000:
712x1472 mm (900 mm wide door)
Standard:
• Door blade and door frame in RAL 9003 (Aritco white)
• Glass window: clear glass (JT0)
Options:
• Door blade and /or door frame in other RAL colour
• Glass window: tinted (JT16), dark tinted (JT5), frosted (JT23)
Aritco 7000:
1)
Door opening
width (mm)
Door opening height
(mm)
Available for B-side
(mm)
Available for A/C
side (mm)
800
18001)/1900/2000
1040
900
900
18001)/1900/2000/2100
1280/1480/1580
1000/1100
10001)
2000/2100
1280/1480/1580
1100
Not available for outdoor lifts.
Aritco 9000:
1)
Door opening
width (mm)
Door opening height
(mm)
Available for B-side
(mm)
Available for A/C
side (mm)
900
18001)/19001)/2000
1400
1000/1100
Note that when having a landing door with door opening height of 1800 or 1900 mm, the cabin
door opening height is still 2000 mm.
23
Landing door - Aritco 7000 and Aritco 9000
EI60 – Fire & smoke proof door
EI60 – Fire & smoke proof door complies with the lift directive 95/16/EC and EN
81-58. As standard the EI60 door is delivered with a frame.
Opening width:
•Aritco 7000: 800, 900, 1000 mm
•Artico 9000: 900 mm
Opening height: •Aritco 7000: 1900, 2000, 2100 mm
•Aritco 9000: 1900, 2000 mm
The actual height of the door is 20 mm higher since a plate that covers the joint
between the door and the frame is mounted on the door.
Installation: For indoor and outdoor lifts. Not in combination with half height door.
Standard:
• Door blade and door frame in RAL 9003 (Aritco white)
• Glass window: clear glass (JT0)
Options:
• Door blade and /or door frame in other RAL colour
Note that for Aritco 9000 it is not possible to have a fire door, EI60 door, on sides
where you have only one door and this door is placed on the bottom floor. This is
since the service hatch is not fire proof.
24
Landing door - Aritco 7000 and Aritco 9000
Aritco 7000:
Door opening width
(mm)
Door opening height (mm) Available for B-side (mm)
Available for A/C side
(mm)
800
1900/2000/2100
1040
900
900
1900/2000/2100
1280/1480/1580
1000/1100
1000
2000/2100
1280/1480
1100
Aritco 9000:
Door opening width
(mm)
900
1)
Door opening height (mm) Available for B-side (mm)
19001)/2000
Available for A/C side
(mm)
1400
1000/1100
Note that when haveing a landingdoor with door opening height of 1900 mm, the cabin door opening height is still 2000 mm.
EI60 – Fire & smoke proof door frame
A door frame is always delivered with the door. The size of the frame depends on platform or cabin size and the door
opening width and height. The height of the frame is always 220 mm higher than the door opening height.
Aritco 7000:
A/C-side
B-side
Door opening height
(mm)
Frame height
(mm)
Platform side
(mm)
Frame size (mm)
Platform side
(mm)
Frame size (mm)
1900
2120
900
1060
1040
1060
2000
2220
1000
1160
1280
1300
2100
2320
1100
1260
1480
1500
1580
1600
For B-side 1980 mm fire doors are not available.
Aritco 9000:
A/C-side
Door opening height
(mm)
Frame height
(mm)
1900
2120
2000
2220
B-side
Cabin side (mm)
Frame size (mm)
Cabin side (mm)
Frame size (mm)
1000
1160
1400
1500
1100
1260
Widening panel for A and C side - Aritco 7000
As an option a widening panel for the A- and C -side can be ordered to cover the machine side part. The
widening panel is available with or without a hatch for the electrical cabinet. The widening panel is available
for door opening height 1900, 2000 and 2100 mm and has the same height as the door frame.
25
Landing door - Aritco 7000
Half height door with glass
Half height door with one glass window. If you require an open shaft
or if the head space is low, the use of a half height door may be a good
solution. According to EN81-41 the half height door is only allowed for
lifts with a travel height up to 3 meters (within EU). The half height door
can not be combined with EI60 fire & smoke proof doors.
Opening widths : Opening heights: Glass windows: (vision)
800, 900 mm
1100-1600 mm
612x670 mm (800 mm wide door)
712x670 mm (900 mm wide door)
Installation: Not for outdoor lifts
Standard:
• Door blade and door frame in RAL 9003 (Aritco white)
• Glass window: clear glass (JT0)
Options:
• Door blade and /or door frame in other RAL colour
• Glass window: tinted (JT16), dark tinted (JT5), frosted (JT23)
Note that when using a half height door 1100-1600 mm the shaft and
the half height door will end at the same height. It is not possible to
have a higher shaft than the half door.
1)
Door opening width
(mm)
Door opening height
(mm)
Available for
B-side (mm)
Available for
A/C-side (mm)
800
1100/1101-16001)
1040
900
900
1100/1101-1600
1280/1480
1000/1100
1)
Custom height
A half height door can be used in the following cases:
•1100 mm high half height door: When you have an open shaft and a top height of 1100 mm (even shaft).
•1101-1600 mm high half height door: When you have a low travel height with a standard door on the bottom
floor and a custom height half height door is needed to get an even shaft (see page 27 for details).
When you have a higher travel height, but a standard door on second top floor and a custom height half door is
needed to get an even shaft.
•It is not possible to have a lower half height door than the top height of the shaft – this means that you can´t
have a 1100 mm height door on a lift with shaft height of for example 1400 mm.
•Note that it is not possible to have two half height doors on the same lift.
26
Landing door - Aritco 7000
For large glass door, double glass door and double
hinged glass door.
690-1190
2240
640 -1140
1100 -160 0
When using a customed height half door, consider the following criteria
regarding travel height. Note that the travel height is depending on if the lift is
installed with or without a pit.
1)
50
Example with door opening height 2000 mm.
27
Door opening
height (mm)1)
Travel height
when a ramp on
first level (mm)
Travel height
with a pit on
first level (mm)
1800
490 – 990
440 – 940
1900
590 – 1090
540 – 1040
2000
690 – 1190
640 – 1140
2100
790 – 1290
740 – 1240
The height of the frame is always 240 mm higher than the
door opening height.
Landing door - Aritco 7000 and Aritco 9000
90 0
A door frame is always delivered with the door. The size
of the frame depends on the platform/cabin size and the
door opening width and height.
The height of the frame is always 240 mm higher than the
door opening height.
2240
Example with door
opening height 2000 mm.
2040
2000
Door frame
Door opening height
The actual height of the door is 40 mm higher since a
plate that covers the joint between the door and the
frame is mounted on the door. For door opening height
2000 mm the actual door height is 2040 mm.
Example with door
opening height 2000 mm.
Frame size:
Aritco 7000:
B -side
A/C -side
Door opening
height (mm)
Frame height
(mm)
Platform side (mm)
Frame size
(mm)
Platform side (mm)
Frame size
(mm)
1800
2040
900
1060
1040
1060
1900
2140
1000
1160
1280
1300
2000
2240
1100
1260
1480
1500
1580
1600
Cabin side (mm)
Frame size
(mm)
2100
2340
Aritco 9000:
A/C -side
B -side
Door opening
height (mm)
Frame height
(mm)
Cabin side (mm)
Frame size
(mm)
1800
2040
1000
1160
1000
1160
1900
2140
1100
1260
1100
1260
2000
2240
28
Landing door - Aritco 7000
Displacement of door on B-side
If it is not possible to fit the door on the B-side in the standard location, it is possible to
place the door to the left or to the right. This is only possible for doors with door opening
width 900 and 1000 and for doors on B-side; 1280, 1480 and 1580 mm. Large glass doors
and half height doors for indoor installations can be displaced. It is not possible to displace
EI60 fire & smoke proof doors or double hinged glass doors or for outdoor lifts.
Door opening 900 mm.
Platform size on
B-side (mm)
Frame size (mm)
Standard frame (mm)
Displaced to the left
(mm)
Displaced to the right
(mm)
Left / Right side of door
Left / Right side of door
Left / Right side of door
1280
1300
200 / 200
130 / 270
270 / 130
1480
1500
300 / 300
130 / 470
470 / 130
1580
1600
350 / 350
130 / 570
570 / 130
Frame size (mm)
Standard frame (mm)
Displaced to the left
(mm)
Displaced to the right
(mm)
Left / Right side of door
Left / Right side of door
Left / Right side of door
Door opening 1000 mm.
Platform size on
B-side (mm)
1280
1300
150 / 150
130 / 170
170 / 130
1480
1500
250 / 250
130 / 370
370 / 130
1580
1600
300 / 300
130 / 470
470 / 130
Examples of possible displacement of door on B-side (door opening 900
mm , platform size on B-side 1480 mm, frame 1500 mm) :
D
C
B
!
â
D
ø%
A
C
A
ø%
C
D
B
!
!
â
A
ø%
B
ø$
ø$
â
!
"
"
"
Standard frame
Displaced to the left
Displaced to the right
29
Landing door - Aritco 7000 and Aritco 9000
Door control
The door control is either placed on the door frame of each landing door and/or
placed away from the lift as an external control.
Door control on door frame
Door control placed on the door frame on the lift.
External door control
– placed away from lift
Door control placed away from the lift in an external
call station box connected to the lift via a cable or as a
radio controlled call button without any cable.
Note that for double hinged glass doors there is no
place for door control in the door frame. External door
control must be used.
Door faceplate
The door faceplate can be placed directly on
the door frame or externally in an external call
station box. The door faceplate is in standard
painted in grey, anodic color Natura which
has an Aluminum look. As an option it can be
delivered in stainless steel.
The door faceplate can hold:
•Call button
Call button
•Key switch Telemecanique/School locking
Call button
+ ASSA
•Key switch prepared for Assa/School locking
Call button
+ Telemecanique
•Key switch prepared for EUR/School locking
•Call button and key switch with
Telemecanique/School locking
•Call button and key switch prepared for ASSA/
School locking
•Call button and key switch prepared for EUR/
School locking
EUR
ASSA
•Call button and sensor - with remote control
Telemecanique
30
Landing door - Aritco 7000 and Aritco 9000
ASSA
Call button
The call button comes with a background lit frame which
indicates the status of the lift.
• Green light indicates that the lift is at your floor. Lit
only on the floor where the platform is at the moment.
• Red light indicates that the lift is occupied. It is busy
and you can’t call for it.
• The flashing light indicates that the security circuit
is broken, e.g. that the emergency button is pressed,
the door is open on another floor for more than one
minute, the door is blocked or the safety frame is
pressed down. The flashing light can also be activated
by a sum alarm, more information is then available in
the service memory.
EUR
Telemecanique
Key switch / School locking
Instead of having a normal call button on the door faceplate you
can have a key switch. You then need to have the key to be able
to call for the lift and to access the lift.
Includes school locking function which automatically locks the
door 10 seconds after it is closed.
Two brands to choose from:
• ASSA (Nordic markets only). Aritco only delivers the housing,
Aritco does not deliver the locking cylinder.
• EUR. Aritco only delivers the housing, Aritco does not deliver
the locking cylinder.
• Telemecanique
Aritco can provide one key switch per door.
The same call button is used when the door control
is placed on the door frame, externally or as a radio
controlled call button.
Radio controlled call button
The radio controlled button, placed in a white plastic box,
gives the customer the freedom to place the call button
wherever they would like within 10 meters from the lift.
The radio controlled call button runs on batteries and
provides remote controlled access to the lift.
The radio controlled call button doesn´t indicate the
status of the lift.
Can be ordered as an option.
External call station box
The door faceplate can be placed away from the lift and will then
be placed in an external call station box. The colour of the external
call station box is RAL 9003 (Aritco white) . The box can either be
mounted exterior on a wall (wall mounted) or in the wall so that you
only see the door faceplate (flush mounted). The length of the cable
delivered with the external call station box is 1,5 m as standard. As
an option a 10 m long cable can be ordered.
Size flush mount: 82x150x50 mm
Size wall mount: 95x185x50 mm
31
Landing door - Aritco 7000 and Aritco 9000
Door machinery
The landing doors are always delivered with either a door opener
or a door closer. Depending on the door type you can either have it
mounted internally (in the door frame so that you can’t see it from
the outside) or externally (in a box visible from the outside).
Internal
door
closer
External
door
closer
External
door
opener
Large glass door
Standard
l
l
l
Half height glass
door
l
l
EI60 – fire & smoke
proof door
l
l
Outdoor lifts
l
Door type
Door opener: Opens and closes the door automatically. Door open
time and the opening speed are adjustable.
Door closer: Door is opened manually. The door is closed
automatically after a preset time.
All openers and closers are available for both left and right hinged
doors.
l
l
When having two doors on the same landing, both doors will be
opened at the same time when having door openers.
Internal door closer
Closes the door automatically after a preset time.
It is built into the door frame and is invisible form the outside.
Includes function to keep door open until the user manually
closes the door. Standard for all doors except large glass
doors with 50 mm frametop.
External door opener
Opens and closes the door automatically after a preset time.
Can be ordered as option. Cover and sides painted in RAL
9003 (Aritco white) as standard. If the door blade is painted
in another color, the cover will be painted in the same color.
The sides will still be in Aritco white.
External door closer
Closes the door automatically after a preset time.
Can be ordered as an option.
Hold open arm
Keeps the door open until the user manually closes the door.
Can be combined with external door closer only.
Can be ordered as an option.
32
Landing door - Aritco 7000 and Aritco 9000
Landing indicator on door
Digital display positioned at the door frame. It shows which floor
the lift is on at the moment.
The landing indicator can also show following system information:
• Warning if the lift batteries are low.
• A bell when the alarm button has been pressed.
• Number of starts and total run time since installation or
since last reset.
• A weight symbol will appear if the lift is overloaded.
• If connected to the buildings fire alarm a “Fire” symbol will be
shown when alarm is activated.
Ramp
If the lift is installed
without a pit a ramp is
mandatory according to EN81.41.
The ramp is made of galvanized steel
covered with corrugated aluminum to prevent slipping. The
vertical rise of the ramp is less than 1:4. The ramp can be
ordered as an option for lifts installed without a pit.
Ramp dimensions for Aritco 7000: Height 50 mm, width
420 mm, length 1160 mm.
Ramp dimensions for Aritco 9000: 75 mm height.
Door handle
Door handle with a diameter of 30 mm is delivered as
standard to all doors (except for double hinged glass doors,
where no door handle is needed). The ends of the handrail
are closed and turned towards the door blade.
• Anodized aluminum (standard)
• Stainless steel (option)
Cover plate
If the door control is placed externally and not on the
door frame a cover plate that covers the hole in the
door frame is delivered with the lift. The cover plate is
always delivered with the lift in the same colour as the
door frame. Standard colour is RAL 9003 (Aritco white).
Arrival gong
The arrival gong gives an audible signal (ding dong) when
the platform arrives at each landing. It is placed in the door
frame on each landing.
Can be ordered as an option.
33
s possible to paint
News. New shaft profile
in any RAL colour.
Shaft
Aritco 7000, Aritco 9000
34
Shaft - Aritco 7000
Shaft
The lift is always delivered with a self supporting shaft. The lift always
comes with cladding panels on the inside of the shaft on the machine
side. If the lift is not installed against a wall, machine side cladding can be
added on the outside of the lift to cover the machine side. For all sides
except for the machine side you can choose to have shaft panels in steel
or glass.
The top height of the shaft for Aritco 7000 is not fixed. When having a
standard door on the top floor, the minimum top height depends on the
door opening height and the frame height. For a door opening height of
2000 mm the standard frame height is 2 240 mm, which is the lowest top
height. Higher top height can be ordered.
Shaft panels
Standard is 25 mm thick shaft panels with
EPS (polystyrene) core and steel plates.
The panels are painted in RAL 9003 (Aritco
white) as standard. If the shaft is painted
in another colour the shaft panels will be
painted in the same colour and the shaft
panels will have a rock-wool core.
The height of the shaft panel is 575 mm.
Cladding panels
Cladding panels covering the
inside of the machine side
are delivered as standard. As
standard the panels are in RAL
9003 (Aritco white), but if shaft
is painted in another colour the
panels will be painted in the
same colour.
(JT5)
(JT23)
(JT16)
(JT0)
Machine side cladding
The machine side cladding in steel covers
the backside of the machine side if the lift
is not mounted against a wall. The machine
side cladding can be ordered as an option
and can run from bottom to top height. It
can also be ordered partly if the lift is partly
mounted to a wall. The cladding is painted
in same colour as shaft panels.
Size: Travel height plus top height.
Shaft inner ceiling
For a closed shaft you can add a shaft
inner ceiling as an option. The inner ceiling
is painted in RAL 9003 (Aritco white) as
standard, but will be painted in the same
colour as the shaft if the shaft is painted
in another colour. Choose between the
following options, which complies with LUX
regulations:
• LED lights or with fluorescent lamp
• Fluorescent lamp (not for 900x1040 mm
platform)
Glass
As an option glass panels with laminated and toghened
glass can be ordered. Standard is clear glass (JT0). Option with
tinted (JT16), dark tinted (JT5) or frosted (JT23) glass.
The glass panels are 8 or 10 mm thick depending on the size of the glass.
Glasses which are higher than 1000 mm is always 10 mm.
The glasses are fitted in aluminium profiles. These profiles are in aluminium
as standard, but can be painted in a RAL colour as an option. For a shaft
painted in the RAL 9003 (Aritco white) the profiles can be painted in the
same colour. For a shaft painted in another RAL colour the profiles are as
standard aluminium. As an option the profiles can be painted in the same
RAL colour. Note that this has to be ordered separately.
Shaft panels / glass with aluminium profile:
1)
Height (mm)
Clear glass
(JT0)
Dark
tinted
glass (JT5)
Tinted
glass
(JT16)
Frosted
glass
(JT23)
736
l
l
l
l
1472
l
l
l
l
2208
l
l
l
l
Customized 1)
l
l
l
l
Additional cost per mm. Maximum height per glass panel is 2500 mm
35
Shaft - Aritco 9000
Shaft
Inner ceiling
The lift is always delivered with a self supporting shaft. The lift
always comes with side cladding panels on the inside of the shaft
on the machine side. For all sides except for the machine side you
can choose to have shaft panels in steel or glass.
The top height of the shaft for Aritco 9000 is not fixed. The
minimum top height is 2400 mm, which is the lowest top height.
Higher top height can be ordered.
To have a closed shaft you can add an inner ceiling as an
option. The inner ceiling is painted in RAL 9003 (Aritco
white) as standard, but will be painted in the same
colour as the shaft if the shaft is painted in another
colour. The inner ceiling is delivered without light. The
ceiling must have a lighting that gives minimum 50
lux at the cabin roof. If the lighting is not provided in
the shipping, it is the owner’s responsibility to mount
lighting with correct capacity.
When using an inner ceiling for the shaft the minimum
top height is 2440 mm.
Cladding panels
Side cladding panels, for the inside of the machine
side are delivered as standard. Middle cladding
panels are not available, since there is no space for
them. That means that you will see the screw from
outside the shaft. This is especially the case when
having a glass shaft, but the screw can also be
seen through the glass in the landing doors. The
screw is thus not visible from inside the cabin. As
standard the panels are in RAL 9003 (Aritco white),
but if shaft is painted in another colour the panels
will be painted in the same colour.
Machine side cladding
The machine side cladding in steel covers the
backside of the machine side. The machine
side cladding can be ordered as an option and
can run from bottom to top height. It can also
be ordered partly if the lift is partly mounted
to a wall. The cladding is painted in the same
colour as the shaft panels.
Size: Travel height plus top height.
Glass
As an option glass panels with laminated and toghened glass
can be ordered. Standard is clear glass (JT0). Option with tinted
(JT16), dark tinted (JT5) or frosted (JT23) glass.
The glass panels are 8 or 10 mm thick depending on the size of the
glass. Glasses which are higher than 1000 mm is always 10 mm.
The glasses are fitted in aluminium profiles. These profiles are in
aluminium as standard, but can be painted in a RAL colour as an
option. For a shaft painted in the RAL 9003 (Aritco white) the profiles
can be painted in the same colour. For a shaft painted in another
RAL colour the profiles are as standard aluminium. As an option the
profiles can be painted in the same RAL colour. Note that this has to
be ordered separately.
Shaft panels
Standard is 25 mm thick shaft panels with
EPS (polystyrene) core and steel plates.
The panels are painted in RAL 9003 (Aritco
white) as standard. If the shaft is painted
in another colour the shaft panels will be
painted in the same colour and the shaft
panels will have a rock-wool core.
The height of the shaft panel is 575 mm.
Shaft panels / glass with aluminium profile:
Height (mm)
Clear glass
(JT0)
Dark
tinted
glass (JT5)
Tinted
glass
(JT16)
Frosted
glass
(JT23)
736
l
l
l
l
1472
l
l
l
l
l
l
l
l
l
l
l
l
2208
Customized
1)
1)
(JT5)
(JT23)
(JT16)
(JT0)
Additional cost per mm. Maximum height per glass panel is 2500 mm
36
Shaft - Aritco 7000 and Aritco 9000
Electrical cabinet
Mast
The standard position of the electrical cabinet is in
the shaft, at the upper floor where the landing door is
located. If the standard position of the electrical cabinet
proves difficult we offer the option to move it to another
landing or to place it externally in a locable casing.
For Aritco 7000 with platform size 900 x 1040 mm the
electrical cabinet is mounted behind the platform panel
and in the top of the shaft.
Size of standard electrical cabinet (placed in shaft):
180 x 880 mm.
Size of external electrical cabinet (placed in an external
box): Height 500 mm, depth: 160 mm, width: 400 mm.
Stativ2008-02-11
For Aritco 7000 and Aritco 9000 the lift can be delivered in
different ways, depending on the length of the lift.
•For travel heights 2 465 -13 000 mm the mast is always
delivered in parts.
•For travel heights 1 720 – 2 464 mm the mast is delivered in
parts as standard, but can be delivered in one part if required.
•For travel heights up to 1 720 mm the mast is always delivered
in one part.
•For travel heights up to 2 464 mm it is possible to have the
mast prepared for splitting.
External service panel
A service panel is always placed in the electrical cabinet.
It is used to run tests etc., and for emergency running the
lift. An external service panel is available for mounting
outside the lift as an option. In this case a wire connects it
with the service panel in the electrical cabinet.
For Aritco 7000 with platform size 900 x 1040 the electrical
cabinet and the standard service panel is mounted in the
top part of the shaft and can´t be reached from outside.
Therefore it is connected to an external service panel which
is mounted in a wall mounted box. The external service panel
must be activated with a 3-edge key before it can be used.
The faceplate is in standard painted in grey, anodic color
Natura which has an Aluminum look.
Size: 95 x 185 mm.
Shaft support bracket / L-bracket
Installed to stabilize the shaft when it is not mounted against a
wall. One shaft support bracket shall be used per floor, except
the bottom floor. The shaft support bracket/L-bracket is fixed
on the lift on the machine side and in the building on A/C-side
(under door). Not possible to fix on B-side.
The shaft support bracket /L-bracket is painted in RAL 9003
(Aritco white) as standard. If the shaft is painted in another color
the shaft support bracket is painted in the same color.
Aritco 7000: The shaft support bracket / L-bracket is available for
platform sizes 1040, 1280, 1480, 1580 and 1980 mm.
Aritco 9000: The machine side of Aritco 9000 must be installed to
a wall and shaft support bracket can´t be used for installation.
Extra anti-rust protection
In order to protect the lift when exposed to humid
environments, e.g. when sea transport or when the
packed lift is exposed to humid conditions during
transport or at the installation site, the lift is delivered
with guides (corrosion class C5).
Can be ordered as an option.
37
Communication - Aritco 7000 and Aritco 9000
Two way communicaion is mandatory according to EN81-41. Choose from
one of the following options or install your own phone.
Autodialer
Equipment for emergency calls. Integrated on the
destination panel. Dials automatically when the
alarm button is pressed.
When unanswered after a predefined time, the call
is automatically forwarded to the next number.
The autodialer can be equipped with a GSM
module. Aritco does not supply SIM card.
DC converter
When more autodialers are connected in series on one
phone line the power on the phone line is not enough to
drive more than one autodialer. In this case, a DC-converter
is needed for each lift. The DC-converter 12-24 V is used as
external power supply for the autodialer.
Phone
The telephone works as a standard telephone but is
intended for emergency calls. The phone is mounted
on the platform panel. Equipped with redial memory,
mute button and a lamp indicator for on/off.
Can be equipped with a GSM module. Aritco does not
supply SIM card.
38
Drive - Aritco 7000 and Aritco 9000
Lubrication
The screw must be oiled at regular intervals.
Manual Lubrication. A brush fixed to the platform oils the
screw when using the lift (a tray with lubrication oil in the
bottom of the shaft). Standard for Aritco 7000.
Automatic Lubrication. Oils the driving screw at regulated time
intervals even if the lift is not in use. The lubrication frequency
is adjustable. Standard for Aritco 9000. Option for Aritco
7000. Standard for lifts with a travel height of over 8000 mm.
Recommended for lifts that are seldom used or that are not
used regularly to travel from ground to top floor.
Power supply
For Aritco 7000 you have the following options:
3-phase 400V / 5.2 A / 16 A slow
•Standard for all lifts (50 Hz)
•Frequency 50 or 60 Hz
•Frequency converter, with build in soft start and stop
(option).
1-phase 230V / 9 A / 16 A slow
•Option when building doesn´t support 400V 3-phase
•Frequency converter, with built in soft start and stop
•Frequency 50 or 60 Hz
3-phase 230V / 9 A / 16 A slow
•Option
•Note that this is rarely used except for example in Norway
and Saudi Arabia
•Frequency 50 or 60 Hz
For Aritco 9000 the following is valid:
3-phase 400V / 5.2 A / 16 A slow
•Frequency converter with built in soft start and soft stop
•Frequency 50 or 60 Hz
Battery operated emergency lowering
All Aritco lifts have battery operated emergency lowering as
standard. You can lower yourself from inside the lift and get out
by yourself when there is a power failure. Possible to run the lift
to nearest level from the platform/cabin (possible to go down)
- Executed when pressing a platform/cabin button. Can also be
run externally from the call button (hold to run) or service box.
Soft start
It provides a smoother start when pressing a destination
button. For Aritco 7000 3-phase lifts, soft start can be
ordered as an option. It is not available for 1-phase lifts,
as they come with a frequency control as standard which
includes both soft start and stop. For 500 kg lifts soft start
is included as standard.
Battery Guard
The battery guard ensures that the batteries are not
damaged and that there is enough power so that you can
run the lift in the case where the power to the lift is cut. It
ensures that the lift is turned off (all power consumers are
turned off) when the power of the batteries reaches 22 V.
This means that even if the power on site is turned off the
batteries in the lift will not be discharged and you can still
run the lift. The battery guard can be order as an option.
Phase sequence relay
Extra protection and to secure that the lift does not run in the
wrong direction when the phases are connected incorrectly.
Option introduced for 3-phase lifts.
39
Outdoor execution - Aritco 7000
Outdoor execution
Aritco 7000 for outdoor execution is designed for outside use and equally suited to cold
northern conditions as well as hot sunny climates. All outdoor lifts are delivered with guides
(corrosion class C5) to avoid corrosion. The outdoor execution consists of different options that
enable an outdoor installation. Depending on the installation environment different options
must be added and the installation conditions are specified below must be followed.
Outdoor execution available for platform size 1100x1480 mm.
Conditions for installation:
Environment temperature max + 40° down to -5°C. If the lift
is going to be installed in colder climate than -5°C, an externally
insulated and heated shaft must be built around the lift.
Options to be ordered depending on installation:
•If the lift is installed outside and rain can reach the machine
side, a machine side cladding must be used.
•If the lift is not installed in an external shaft an outer roof
must be used. Inner ceiling with light (LED or fluorescent
lamp) – must be ordered for outdoor lifts when ordering a
roof.
Windload up to 10 m/s. Protection against wind loads over 10
m/s is required. In areas where it can be expected to be more
wind load than 10 m/s, Aritco recommends a windshield or
an external building around the shaft. An option for wind load
25m/s is also available (Eurocode 1991-1-4:2005).
•Heater installed in bottom of the shaft, with bottom panel
with ventilation holes – option recommended for cold
climates.
Snow load max 2kN/m2. Snow load zone according to EN
1991-1-3. For higher snow loads an external shaft / roof must
be installed.
•Seal of machine side cladding / outdoor roof with a a tape/
strip.
•If the lift is installed outdoor and there is no roof over the
doors, door canopies must be installed over the doors. –
Option recommended for outdoor lifts.
Installation above ground level and with a drained pit. The
lift must be installed above ground level and water should be
directed away from the lift. The lift pit must be drained and the
pit shall also be protected from freezing. The lift is not water
tight and water can leak into the lift via landing doors or shaft.
Aritco reserves the right to deny warranty claims if the lift is not
installed in the right environment and if necessary equipment
is not used.
Installation is not recommended in salt or chlorine enhanced
environment. For example the lift must not be installed close
to see or close to a swimming pool.
Installation only outdoor. The lift must be installed only
outdoor, i.e. with all landing doors towards the outside. The
lift must not be installed with landing doors that go into the
building. Otherwise the lift can be subjected to downdraughts
with condensation problems as a consequence.
Limitations for outdoor lifts:
Limitations for wind load up to 10m/s:
•Maximum Travel height: 10m
•Shaft panels on EPS only (Rock wool not available) or glass
shaft panels.
Included in standard when ordering an outdoor lift:
•Guides (corrosion class C5) to avoid corrosion
•Lift in default color only. Shaft / doors in RAL 9003 (Aritco
white) platform panels on RAL 7042 (grey).
•Electrical cabinet cover sealed
•Possible to fix lift with L-bracket (specially developed for
outdoor usage).
•Screw sprayed with oil
•A special oil, aimed for outdoor usage must be used (lower
temperature grading)
Additional limitations for wind load up to 25m/s:
•Shaft only with shaft panels in EPS. Glass shaft panels not
available. Shaft is glued.
• To avoid water leakage, all joints on top roof are to be sealed
after installation.
•Ventilation fan in top of shaft, with upper panel with fan
holes and lower panel with ventilation holes are mandatory
for all outdoor lifts.
•Lift must be fixed against a wall. Fixing with L-brackets are not
possible.
•Call buttons protected against water, resistant to weather and
condensation)
Please note that the following are not possible for outdoor lifts:
•Large glass doors with width 1000 mm
•Large glass door with height 1800 mm
•Half height doors – all sizes
•Displacement of door on B-side
•Fixing elements better protected against rust (Zink Nickel)
•Sealing of doors: A brush stripe for doors thar reduces the
dirt (and in some extent water) to come into the lift.
•All painted parts have corrosion class C3.
40
Roof
Roof for outdoor execution. If the lift
is not installed in an external shaft an
outer roof must be used. One roof
corner is left open for water outlet.
The roof is made of galvanized steel
and painted in RAL 9003 (Aritco white)
as standard. An inner ceiling with light
(LED or fluorescent lamp) must be
ordered for outdoor lifts when ordering
a roof.
Door canopy
A sloping roof placed above the landing
doors to protect them from rain and
snow etc. The door canopy is made
of galvanized steel and painted in RAL
9003 (Aritco white) as standard.
Width: 1160 mm
Slope angle: 23°
Heater
Ventilation fans
A heater placed in the bottom of the shaft is
recommended for cold climates. Can be ordered as an
option .The heater of 2000 W must be connected to an
external power socket. Note that for colder climates than
-5°the lift must be installed in an external heated shaft.
Ventilation fans mounted in top of the shaft. Two axial
fans 230 V, 12 W. The fans are connected to an external
power socket, 230 V.
The fans are mandatory for outdoor lifts.
41
Aritco 7000 Flexi
Aritco 7000 Flexi
Aritco 7000 Flexi is a version of the Aritco 7000 lift that is intended for both persons and goods. A risk assessment has
been conducted to assess the additional risk that will come when using the platform for both persons as well as for
goods (Lighter goods transport max 500 kg). Measures to reduce these risks have been taken and they are now implemented for Aritco 7000 Flexi. Aritco 7000 Flexi has its own certificate, which is available on the partner desktop. Aritco
7000 Flexi is available for all platform sizes.
The following is included when ordering an Aritco 7000 Flexi:
•Platform with safety edge painted in yellow (RAL 1018).
•Platform with security list mounted behind the platform faceplate painted in yellow (RAL 1018). Valid when having a
half height wall.
•Loading information label - warning sign placed on the platform panel.
•User manual is updated with the Aritco 7000 Flexi option and its informs the user of where to place the goods and
what size of goods that can be transported with the lift.
•Certificate for persons and goods.
Loading information label
A loading information label is placed on the platform with
pictograms warning for the following:
•Do not load any goods on or outside the yellow border of the
platform (safety edges). Prevents the goods to get in contact with
the lift walls and get stuck between shaft wall and platform.
•Do not load any goods that are higher than 2 m on the platform.
The minimum requirement for free space on top floor is 2 m, the
goods will then always have free space upwards.
≤ 2 Meter
> 2 Meter
More information in Aritco 7000 User manual.
Safety edge in RAL 1018
42
Safety list in RAL 1018
Steel kerb
For extra protection of the platform and the shaft walls a steel
kerb can be ordered as an option for Aritco 7000 Flexi. The steel
kerb is a 90 mm high steel frame placed on all sided on the
platform, except for door sides. It is recommended when using
the lift also for goods. The safety edge will be specially made to
fit the steel kerb.
43
Drawings - Aritco 7000
Platform 900 × 1040
+15
Hole through floor = 1190 –0
900 × 1040
130
Platform = 1040 including safety list
+15
Hole through floor = 1305 –0
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1160
800
+15
Hole through floor = 1190 –0
130
Platform = 1040 including safety list
800
130
800
130
44
+15
Hole through floor = 1330 –0
900 × 1040
Shaft width = 1300
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1160
Drawings - Aritco 7000
Platform 900 × 1280
+15
Hole through floor = 1430 –0
900 × 1280
130
Platform = 1280 including safety list
+15
Hole through floor = 1305 –0
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1400
800
+15
Hole through floor = 1430 –0
130
Platform = 1280 including safety list
800
200
900
200
45
+15
Hole through floor = 1330 –0
900 × 1280
Shaft width = 1300
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1400
Drawings - Aritco 7000
Platform 900 × 1480
+15
Hole through floor = 1630 –0
900 × 1480
130
Platform = 1480 including safety list
+15
Hole through floor = 1305 –0
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1600
800
+15
Hole through floor = 1630 –0
130
Platform = 1480 including safety list
800
300
900
300
46
Shaft width = 1300
900 × 1480
+15
Hole through floor = 1330 –0
Door opening width = 800
Platform = 900 including safety list
130
215
Shaft length = 1600
Drawings - Aritco 7000
Platform 1000 × 1280
+15
Hole through floor = 1430 –0
Door opening width = 900
1000 × 1280
130
Platform = 1280 including safety list
+15
Hole through floor = 1405 –0
Platform = 1000 including safety list
130
215
Shaft length = 1400
900
+15
Hole through floor = 1430 –0
130
Platform = 1280 including safety list
900
200
900
200
47
+15
Hole through floor = 1430 –0
Door opening width = 900
1000 × 1280
Shaft width = 1400
Platform = 1000 including safety list
130
215
Shaft length = 1400
Drawings - Aritco 7000
Platform 1000 × 1480
+15
Hole through floor = 1630 –0
Door opening width = 900
1000 × 1480
130
Platform = 1480 including safety list
+15
Hole through floor = 1405 –0
Platform = 1000 including safety list
130
215
Shaft length = 1600
900
+15
Hole through floor = 1630 –0
130
Platform = 1480 including safety list
900
300
900
300
48
+15
Hole through floor = 1430 –0
Door opening width = 900
Platform = 1000 including safety list
1000 × 1480
Shaft width = 1400
130
215
Shaft length = 1600
Drawings - Aritco 7000
Platform 1000 × 1980
+15
Hole through floor = 2130 –0
130
Platform = 1980 including safety list
900
49
+15
Hole through floor = 1405 –0
1000 × 1980
Door opening width = 900
Platform = 1000 including safety list
130
215
Shaft length = 2100
Drawings - Aritco 7000
Platform 1100 × 1480
+15
Hole through floor = 1630 –0
Door opening width = 900
Platform = 1100 including safety list
1100 × 1480
180
Platform = 1480 including safety list
+15
Hole through floor = 1505 –0
180
215
Shaft length = 1600
900
+15
Hole through floor = 1630 –0
180
Platform = 1480 including safety list
900
300
900
300
50
+15
Hole through floor = 1530 –0
Door opening width = 900
Platform = 1100 including safety list
1100 × 1480
Shaft width = 1500
180
215
Shaft length = 1600
Drawings - Aritco 7000
Platform 1100 × 1580
+15
Hole through floor = 1730 –0
Door opening width = 900
Platform = 1100 including safety list
1100 × 1580
180
Platform = 1580 including safety list
+15
Hole through floor = 1505 –0
180
215
Shaft length = 1700
900
+15
Hole through floor = 1730 –0
180
Platform = 1580 including safety list
900
350
900
350
51
+15
Hole through floor = 1530 –0
Door opening width = 900
Platform = 1100 including safety list
1100 × 1580
Shaft width = 1500
180
215
Shaft length = 1700
Drawings - Aritco 9000
Cabin 1000 × 1400
+15
Hole through floor = 1630 –0
130
Cabin = 1400
+15
Hole through floor = 1465 –0
Door opening width = 900
Cabin = 1000
1000 x 1400
Shaft width = 1435
130
275
Shaft length = 1600
900
+15
Hole through floor = 1630 –0
130
Cabin = 1400
900
300
900
300
52
+15
Hole through floor = 1490 –0
Door opening width = 900
Cabin = 1000
1000 x 1400
Shaft width = 1460
130
275
Shaft length = 1600
Drawings - Aritco 9000
Cabin 1100 × 1400
+15
Hole through floor = 1630 –0
180
Cabin = 1400
+15
Hole through floor = 1565 –0
Cabin = 1100
1100 x 1400
Shaft width = 1535
Door opening width = 900
180
275
Shaft length = 1600
900
+15
Hole through floor = 1630 –0
180
Cabin = 1400
900
300
900
300
53
+15
Hole through floor = 1590 –0
Cabin = 1100
1100 x 1400
Shaft width = 1560
Door opening width = 900
180
275
Shaft length = 1600
FAQ
FAQ
1. Can I have the lift painted in any colour?
Both Aritco 7000 and Aritco 9000 can be painted in any RAL colour or in Metallic colour Silver.
Following choices are available:
Whole lift painted in standard colour RAL 9003 (Aritco white):
•Whole lift painted in RAL 9003 ( For Aritco 7000 the platform panels are painted in RAL 7042 (Grey).
Whole lift painted in other colour:
•Whole lift painted in optional colour (Incl. shaft, doors and platform
panels for Aritco 7000.)
Lift partially painted in different colours:
•Shaft in one colour (Incl. shaft panels, corner profiles, Architraves, etc.)
•All door blades in one colour.
•All door frames in one colour (Also includes the door faceplate.)
•Platform panels in one colour - valid for Aritco 7000 only.
•One of the above choices or a combination of them.
Note that all doors must be painted in the same way. It is not possible to paint them
differently.
Definition of Aritco white is RAL 9003 structure with gloss 20 (i.e. it is a matte colour). When ordering
another RAL colour on the lift it will be with structure and with gloss 12.
Any RAL colour means in this case any RAL color from the 213 colur RAL chart K7 classic.
Common colours:
RAL 1015
RAL 3020
RAL 5002
RAL 7012
RAL 7016
RAL 7045
RAL 7047
RAL 8017
RAL 9005
RAL 9006
RAL 9007
RAL 9010
RAL 9016
Shorter lead time and lower price
Other colours:
Rest of the colours from RAL chart K7 classic. Longer lead time and higher price.
Note that only Metallic colour silver, gloss 100+/-5% is available for sale.
2. To which standards do the lifts comply?:
Aritco 7000 and Aritco 9000 comply with the Machine Directive 2006/42/EC, Arico 7000 by following the harmonized
standard EN81-41. The lifts are also compliant with the Electromagnetic compatibility (EMC) – 2004 and Low voltage
Directive 2006/95/EC. The lifts are type approved, CE marked. EI60 – Fire & smoke proof door complies with the lift
directive 95/16/EC and EN 81-58. A certificate for respective lift is available on partner desktop.
54
FAQ
3. What kind of wheelchair can be fitted in the lift?
Aritco 7000:
Both Aritco 7000 and Aritco 9000 follows the requirements
stated for lifts regarding the possibility to fit a wheelchair with or
without attendent. Depending on the size of the platform / cabin
you can fit either a wheelchair or a wheelchair with an attendent:
Platform size
Type A and B wheelchairs are defined in :
EN 12183 Manual wheelchairs – requirements and test methods
EN 12184 Electrically powered wheelchairs, scooters and their
charges – Requirements and test methods
Dimensions of
wheelchair
Class A
Class B
Total length
1200
1400
Total width
700
700
900x1040
-
900x1280
Lone user, or type A wheelchair
900x1480
Type A and B wheelchair with attendent
1000x1280
Lone user, or type A wheelchair
1000x1480
Type A and B wheelchair with attendent
1000x1980
Type A and B wheelchair with attendent
1100x1480
Type A and B wheelchair with attendent
and adjacent entries
1100x1580
Type A and B wheelchair with attendent
and adjacent entries
Aritco 9000:
Cabin size
EN81-41 and EN81-70 defines the sizes of the platform / cabin
and what type of wheelchair it is intended for.
1000x1400
Type A and B wheelchair with attendent
1100x1400
Type A and B wheelchair with attendent
and adjacent entries
4. What are the reaction forces on the building and force on fixings to support frame to wall?
Details regarding the forces are available in the installation manual for Aritco 7000 and Aritco 9000.
Aritco 7000
Reaction forces from the lift to the building:
Travel
height (m)
Area “A” F(kN)
Area “B” Shaft
panels F(kN)
Area “B” Glass
Shaft F(kN)
1
7,8
2,55
3,30
2
8,5
3,40
4,40
3
9,2
4,25
5,50
4
9,9
5,10
6,60
5
10,7
5,95
7,70
6
11,5
6,80
8,80
7
12,0
7,65
9,90
• Maximum force as a function of the lift´s travel.
The force is distributed to the floor through the
mast bottom with the area “A” and to the shaft
bottom with the area “B”.
Mast
Area “A”
Shaft
Area “B”
Force on fixing to to support frame (mast) to wall:
8
12,8
8,50
11,00
9
13,4
9,35
12,10
10
14,2
10,20
13,20
11
14,9
11,05
14,30
12
15,6
11,90
15,40
max 1,2 m
• The miniumum distance between lower floor
and the highest fixing is 2,0 m.
F
max 4,0 m
max 4,0 m
• c -t = distance from the top of the mast to the
highest fixing into the wall.
max 4,0 m
min 2,0 m
• The maximum distance between the top of the
mast and highest fixing is 1,2 m
55
c-c
• The maximum distance between two fixings or
lower floor and the lowest fixing is 4,0m.
c-t
• c -c = distance (height) from the floor to the
highest fixing into the wall.
c -c (m)
F(kN) 410
kg load
F(kN) 500
kg load
2
1.5
2.2
3
1.0
1.5
4
0.8
1.1
5
0.6
0.9
6
0.5
0.7
7
0.4
0.6
8
0.5
0.5
9
0.3
0.5
10
0.3
0.4
FAQ
Aritco 9000
Travel
height (m)
Reaction forces from the lift to the building:
• Maximum force as a function of the lift´s travel.
The force is distributed to the floor through
the mast bottom with the area “A” and to the
shaft bottom with the area “B”.
Mast
Area “A”
Shaft
Area “B”
Area “A” F(kN)
Area “B” Shaft
panels F(kN)
Area “B” Glass
Shaft F(kN)
1
10,6
2,55
3,30
2
11,3
3,40
4,40
3
12,0
4,25
5,50
4
12,7
5,10
6,60
5
13,5
5,95
7,70
6
14,3
6,80
8,80
7
14,8
7,65
9,90
8
15,6
8,50
11,00
9
16,2
9,35
12,10
10
17,0
10,20
13,20
11
17,7
11,05
14,30
12
18,4
11,90
15,40
13
19,1
12,75
16,50
max 1,2 m
• The maximum distance between two fixings or
lower floor and the lowest fixing is 3,0m.
F
• The miniumum distance between lower floor
and the highest fixing is 2,0 m.
max 3,0 m
max 3,0 m
• c -t = distance from the top of the mast to the
highest fixing into the wall.
max 3,0 m
min 2,0 m
• The maximum distance between the top of the
mast and highest fixing is 1,2 m
56
c-c
• c -c = distance (height) from the floor to the
highest fixing into the wall.
c-t
Force on fixing to to support frame (mast) to wall:
c -c (m)
F(kN) 400
kg load
2
1.5
3
1.0
4
0.8
5
0.6
6
0.5
7
0.4
8
0.4
9
0.3
10
0.3
Features and benefits
You can always get out of the lift by yourself
• If there is a power failure, you can always get out of
the lift by yourself with battery operated emergency
lowering. Use the platform buttons and the lift will
take you to the closest lower floor and you can open
the door and get out by yourself.
The lift can´t fall down
• With the self locking concept, i.e the
friction between screw and nut will
prevent the lift from falling down. No
additional brake system is needed.
Easy installation
• Means that the lift
is both easy and fast
to install. A normal
installation only takes
two days .
Minimum builders work
and small footprint
• The lift can be installed
without a pit, with a
ramp (or with a 50 mm
pit for Aritco 7000 and
75 mm pit for Aritco
9000, without ramp).
• All parts are included
in the shaft - no extra
machine room or head
room needed.
Low operation and
maintenance cost.
• Lowest on the
market.
No hydraulics, which
mean no leakage or smell
• No additional space
needed for hydraulic unit.
Robust shaft
• 25 mm shaft panels. Robust and
resistant to damage.
• Good noise and acoustical isolation.
Environmental Product Declaration
•We are the first lift manufacturer with an
Environmental Product Declaration
Low energy consumption
• Minimum stand-by power
consumption 15 W – not more
than a computer or a TV.
• Energy class A as per VDI 4707.
•More than 95% of the parts are recyclable.
Energy
More efficient
A
A
B
C
D
E
Less efficient
57
F
G
Order information
PRODUCT RANGE:
The purpose of this product catalogue is to show what Aritco can offer in terms of products, options and
possible combinations. We have no possibility to deliver options that are not in the product catalogue.
Some highlights:
LEAD-TIME
Normal lead time for a standard Aritco 7000 is less than 3
weeks. For a standard Aritco 9000 the normal lead time is
less than 6 weeks. During July and August, the lead-time
can be slightly higher. Some options have a longer lead
time – which is clearly communicated in the ordering system
AOS and the price list. Note that it is always the order
confirmation that states the final delivery time.
Transport of several lifts at the same time:
•When you already know from the time that you order
the lifts that you like to transport several lifts together,
you must request the lifts to be produced in the same
production week. Choose the production week for the lift
with the longest lead time.
•If you don´t know at the time of ordering the lift that you
like to transport several lifts at the same time, you need to
let us know latest 10 days before planned production week
that you like to transport several lifts together. We will
then look on the feasibility of doing this, and it is of course
easier to make changes the sooner we get this request.
95% DELIVERY ACCURACY OF PRODUCTS
During more than 4 years, we have had a delivery accuracy
of more than 95%, i.e. we have delivered within the agreed
delivery week.
DELIVERY ACCURACY OF SPARE PARTS
If the spare part order is received before 2.00 p.m. the aim
is to deliver the same day. Again – for more than 4 years we
have had an accuracy of more than 95%.
ARITCO PARTNER DESKTOP
Our web site www.aritco.com is the centre for all our
information and communication. Make sure you have a
log-in to the Partner Desktop. If you do not have one, just
contact your sales representative. On the Partner Desktop
you will find, among others, this product catalogue, pricelists,
technical documentation, picture gallery, news etc – always
up to date.
TRANSPORT, PACKAGING AND STORAGE
You have two options when it comes to shipping carrier;
•By Aritco, due to agreement – (we book the shipping)
•Not by Aritco – (you take care of the shipping yourself)
Depending on how you are going to transport your lift, the
lift can be packed in different ways.
Packing for shipping method:
•By trailer (worldwide)
We have no room to store finished lifts. Thus when placing
your order you must be sure of the delivery date so that you
can ship the lift as soon as it leaves our production line. After
that they will be shipped to you. Storage cost according to
the price list will be added.
ORDER AND CANCELLATION
It is only possible to order a complete lift in the AOS. If
additional parts are needed they can be ordered as spare
parts (such as shaft panels, keys etc.).
Orders with more than 10 days left until the start of promised
production week:
These orders can be changed. The procedure is that you
cancel the order and then place a new one. The downside is
that you get a new order number and we cannot guarantee
that you get the same slot. Since the material has already
been ordered there will be a cancellation fee depending on
the material involved.
Orders with less than 10 days left until the start of the
promised production week:
For these orders, it is unfortunately too late to make changes.
Too many processes are by then already initiated, and we
have no time to fill this slot with another lift. If your customer
wants to change the travel height or to change a door hinge,
you should contact our After Sales Dept who may be able to
help you.
•By boat in container without crate FCL1)
•By boat and container with crate LCL1)
•By air-freight in crate
1)
FCL means Full Container Load and LCL means Less
Container Load.
58
Overview Aritco 7000
900 x 1040
900 x 1480
900 x 1280
â
á!
ø!
Hole through floor:1405x2130 mm
Plattform: 1000x1980 mm
Load: 500 kg
Wheelchair: A or B with attendent
$!
"!
"!
ø%
Hole through floor: 1430x1630 mm
(No door on B-side: 1405x1630)
Platform: 1000x1480 mm
Load: 410, 500 kg
Wheelchair: A or B with attendent
1100 x 1580
á!
!!
1100 x 1480
ø!
ø%
Hole through floor: 1430x1430 mm
(No door on B-side: 1405x1430)
Platform: 1000x1280 mm
Load: 410 kg
Wheelchair: Lone user or type A
Hole through floor: 1330x1630 mm
(No door on B-side: 1305x1630)
Platform: 900x1480 mm
Load: 410, 500 kg
Wheelchair: A or B with attendent
1000 x 1980
á!
ø!
%
ø%
Hole through floor: 1330x1430 mm
(No door on B-side: 1305x1430)
Platform: 900x1280 mm
Load: 410 kg
Wheelchair: Lone user or type A
1000 x 1480
ø!
â
%
Hole through floor: 1330x1190 mm
(No door on B-side: 1305x1190)
Platform: 900x1040 mm
Load: 250 kg
Wheelchair: -
1000 x 1280
!!
â
!!
â
ø
"%
Hole through floor: 1530x1730 mm
(No door on B-side: 1505x1730)
Platform: 1100x1580 mm
Load: 500 kg
Wheelchair: A or B with attendent,
adjacent entry.
Hole through floor: 1530x1630 mm
(No door on B-side: 1505x1630)
Platform: 1100x1480 mm
Load: 410, 500 kg
Wheelchair: A or B with attendent, adjacent entry.
Overview Aritco 9000
1000 x 1400
1100 x 1400
á!
á!
59
ø
"â
Hole through floor: 1490x1630 mm
(No door on B-side: 1465x1630 mm)
Cabin size: 1000x1400 mm
Load: 400 kg
Wheelchair: A or B with attendent
øâ
ø
Hole through floor : 1590x1630 mm
(No door on B-side: 1565x1630 mm)
Cabin size: 1100x1400 mm
Load: 400 kg
Wheelchair: A or B with attendent,
adjacent entry.
ARITCO LIFT AUGUST 2015 -EN
Aritco is a world-leading manufacturer of platform lifts and home lifts. It has around 90 employees
and sales of approximately SEK 300 million. Aritco produces two types of lifts; home lifts for the
private residential market and platform lifts for the public accessibility market.
Read more at www.aritco.com, www.aritcohomelifts.com or www.aritcoplatformlifts.com
Certified partner:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising