Recording Animation Troubleshooting Power Supply

Recording Animation Troubleshooting Power Supply
Recording Animation
Recording Animation
The PicoBoo JR can record up to 4 minutes of animation.
REC
1
2
TAP RECORD TO
START RECORDING
REC
1
2
REC
1
2
TAP RECORD TO
STOP RECORDING
ANIMATE THE RELAYS
USING THE 1 & 2 BUTTONS
Quick-Start Guide
PicoBoo JR
Previewing your Scare
REC
1
2
TAP 2 TO START
PLAYING THE SCARE
REC
1
2
THE REC LIGHT WILL BLINK
AS YOUR SCARE PLAYS
REC
1
2
NEED HELP?
There are videos, a full manual, and more diagrams available online.
TAP 2 TO CANCEL
PLAYBACK
Write-Protecting Your Audio and Animation
The write-protect setting can be toggled on or off by powering up the PicoBoo while holding the 2 button. When
the red light flashes a few times the write-protect has been toggled.
Power Supply
POWER CAN BE SUPPLIED USING
THE BARREL CONNECTOR OR THE TRIGGER
TERMINAL BLOCK.
Troubleshooting
Factory Reset
If at any point you want to start from scratch, power up while holding the REC button for 10 seconds to factory reset.
Add up the wattage of all the devices that will
be used at the same time and make sure your
power supply’s wattage is equal to or higher
than that number. Use 2 watts for the PicoBoo.
Don’t see your problem here? Check our website for more information.
PWR
-
IN
2
10A./125V MAX EACH
RELAY OUTPUTS
+
9-12V
+
C
N.O.
1
N.C.
C
N.O.
N.C.
The yellow IN light is flashing or throbbing and the PicoBoo won’t trigger.
The PicoBoo is currently ignoring the trigger. It does this at startup to allow a PIR motion sensor to warm up, or
anytime a triggered scene is cancelled by pressing the 2 button. It will resume normal operation shortly.
The REC button is not responding. Can’t record animation.
• The PicoBoo may be write-protected. See Write-Protecting Your Audio and Animation above.
Sizing your Power Supply
Your PicoBoo’s power supply must be 12 volts
DC. The wattage you’ll need will vary if you’re
trying to power other devices from the same
supply.
TRIGGER
Example:
2 watts
+ 6 watts
= 8 watts
PicoBoo
1 x 12VDC 6 watt solenoids
Total - Need at least 8 watts
Trigger Input Wiring
SENSOR WIRES
BLACK
GND (-)
RED
12VDC (+)
WHITE
RELAY C
GREEN RELAY N.O.
-
RELAY OUTPUTS
TRIGGER
ANY 12 VDC DEVICE
IN
+
TRIGGER
IN
2
10A./125V MAX EACH
+
C
N.O.
N.C.
C
N.O.
N.C.
1
-
PRESSURE MAT
NOTE: PIR SENSORS CAN TAKE UP TO A
MINUTE TO “WARM UP”. DURING THIS TIME
THE PICOBOO’S YELLOW INPUT LIGHT WILL
FLASH.
PUSH BUTTON
-
TRIGGER
PIR MOTION SENSOR
TRIGGER
PRESSURE MAT OR PUSHBUTTON
TWO 12 VDC DEVICES
LOOPED WITH
ON/OFF OPTION
ANY VOLTAGE
DEVICE
RELAY OUTPUTS
ANY 110 VOLT LOAD
ANY DEVICE THAT’S NOT 12 VDC
BLUE = FAST
GREEN = SLOW
C
N.O.
BLUE = FAST
GREEN = SLOW
-
RELAY OUTPUTS
RELAY OUTPUTS
TRIGGER
12 VDC MOTOR FORWARD AND REVERSE
TO WALL
OUTLET
SEE OUR WEBSITE FOR A COMPATIBLE
FOG MACHINE CABLE SO YOU DON’T HAVE
TO HACK YOUR REMOTE.
12 VDC
DEVICE
HIGH
VOLTAGE
RELAY OUTPUTS
FOG MACHINE
RELAY OUTPUTS
-
IN
2
10A./125V MAX EACH
+
C
N.O.
1
N.C.
C
N.O.
2
10A./125V MAX EACH
N.C.
C
N.O.
1
N.C.
C
N.O.
OR
1. UNPLUG FOG MACHINE
2. OPEN REMOTE
3. LOCATE FOG BUTTON PINS
4. SOLDER A WIRE TO EACH PIN
5. CONNECT THOSE WIRES AS
SHOWN
TRIGGER
ONE 110 VOLT DEVICE, ONE 12 VDC DEVICE
+
IN
+
IN
TRIGGER
CONTINUOUS PLAY (LOOPED)
RELAY
OUTPUT
TO TRIGGER
POWER
CONNECT THESE ONLY
IF THE BASE RUNS ON
12 VDC AND DOES NOT
HAVE ITS OWN POWER
SUPPLY CONNECTED.
WIRELESS TRIGGER
IN
-
+
N.O.
C
N.C.
C
N.O.
2
-
TRIGGER
FOG
MACHINE
FOG
N.C.
1
10A./125V MAX EACH
TRIGGER
12 VDC MOTOR ON/OFF IN ONE DIRECTION
HIGH
VOLTAGE
N.C.
-
IN
2
+
N.O.
C
N.C.
N.O.
C
N.C.
1
10A./125V MAX EACH
USE A 12V 5A POWER
SUPPLY FOR THE
PICOBOO.
IN
+
USE A 12V 5A POWER
SUPPLY FOR THE
PICOBOO.
TRIGGER
BEAM SENSOR
10A./125V MAX EACH
-
+
IN
TRIGGER
-
BASE STATION
-
TRIGGER
REMOTE
ADDITIONAL
PICOBOO
-
IN
2
+
N.O.
C
N.C.
C
N.O.
1
10A./125V MAX EACH
RELAY OUTPUTS
-
SENSOR WIRES
BLUE
GND (-)
BROWN 12VDC (+)
WHITE
RELAY C
BLACK RELAY N.O.
+
C
N.C.
!
N.O.
N.C.
C
N.O.
N.C.
2
TAKE APPROPRIATE
SAFETY PRECAUTIONS
WHEN WIRING HIGH
VOLTAGES.
TO WALL
OUTLET
IN
HIGH
VOLTAGE
TO POWER SUPPLY
APPROPRIATE
FOR DEVICE
1
SWITCH
LOOPED
+
RELAY OUTPUTS
-
IN
2
12 VDC
DEVICE
A 12V 2A OR HIGHER
POWER SUPPLY MAY
BE REQUIRED IF THE
AMPLIFIER IS USED.
+
C
N.O.
N.C.
C
N.O.
N.C.
1
10A./125V MAX EACH
12 VDC
DEVICE
IN
EXAMPLES OF 12 VDC
DEVICES: LED LIGHTS,
SOLENOIDS, HORNS,
CAR ACCESSORIES, ETC.
12 VDC
DEVICE
+
Relay Output Wiring
TRIGGER
CONNECT THE TRIGGER AS
SHOWN IN ONE OF THE
OTHER DIAGRAMS.
CONNECT ADDITIONAL
PICOBOOS TO THE FIRST
PICOBOO AS SHOWN.
FIRST
PICOBOO
MULTIPLE PICOBOOS WITH ONE TRIGGER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising