Output interfaces

Output interfaces
EN
Output interfaces
TDS13620
DALI - DSI - DMX interface
TDS13620 is a TELETASK- AUTOBUS interface for DALI / DSI / DMX. It can be configured
to integrate up to 64 DALI ballasts or 1 DSI output or 64 DMX compliant channels in
combination with the TELETASK domotics system.
The interface is suited for controlling monochrome and multicolour ballasts and lighting units
with DALI, DSI or DMX control input. The interface supports ramp speeds up to 1 hour, also
for DALI/DSI.
The TDS13620 interface has a manual override button and an external override input which
can be used in case of emergency/evacuation.
Advantage of DSI over DALI: In case of failure or replacement of DSI electronic ballast, the
unit replaced does not need to be re-addressed/configured.
Advantage of DALI/DSI over 1-10V: It dims to off, so no mains switching equipment is
required to turn them off.
Advantage of DALI: individual (addressable) and grouped control, including
feed-back to the TDS system when ballast or lamp is defect.
APPLICATION
Output interface to control 64 DALI or 1 DSI or 64 DMX
compliant channels
A: Recommended: Use DALISOFT together with the
TDS20620V2 DALI-address configuration tool:
1. Disconnect the TDS13620 from the DALI-bus.
2. Connect the TDS20620V2 (see datasheet TDS20620V2).
3. Use DALISOFT within the PROSOFT suite, to assign the
DALI-addresses.
CHARACTERISTICS
Outputs
DALI output: up to 64 DALI ballasts/addresses.
DSI output: 1 DSI output / up to 100 ballasts.
DMX output: up to 64 DMX addresses.
The DALI / DSI / DMX bus is 1500V galvanic isolated from the
AUTOBUS (higher available on request).
Build-in DALI/DSI power supply (power is taken from the
AUTOBUS for both galvanic sides). No external power supply
is needed.
B:
1.
2.
3.
4.
5.
6.
Override
Manual override button: When pressed, the output alters to
40% (LED blinking) to 100% (LED ON) to normal/OFF (LED
OFF). As soon as an AUTOBUS command is received, the
manual override will get ignored until pushed again.
External override contact: Must be a voltage free contact within
100m away from the interface. When the external contact is
closed, all connected DALI/DSI/DMX devices will go to 100%
(LED ON). If this contact is used, it may be necessary to
implement this feature into the emergency evacuation
procedures of the concerned area/building.
7.
8.
DSI address
Not applicable
DMX address
0 to 255 (max. 64 addresses can be defined).
Follow the supplier instructions of the used DMX devices for
address configuration.
DALI feedback features
Touch panel LED will blink on lamp/ballast defect.
Full status information of every individual lamp/ballast address
is available in PROSOFT-Diagnostics.
INSTALLATION
DIN-rail mounting
4 modules wide
SETTINGS
AUTOBUS address
Via two rotary switches ‘Tens’ and ‘Units’.
CONNECTION
AUTOBUS
AUTOBUS connector set + patch cable supplied with this unit
Configuration
Via PROSOFT Suite 3.3 or higher (to be set as DALI- or DSIor DMX-mode).
DALI / DSI / DMX
Screw terminals for wires max. 1.5mm² (solid or stranded).
DMX: Always use shielded cable with twisted pair wires (1 pair
for DMX data and 1 wire for 0V signal)
DALI/DSI wire sections:
0.5mm² for total cable length 0-100m
0.75mm² for total cable length 100m-150m
1.5mm² for total cable length 150m-300m
Jumpers
Terminating resistor (supplied with the interface). To be used
when the interface is at the physical end of the AUTOBUS
cable.
DALI address
The ballast must be addressed before connecting. Groups are
simply configured within PROSOFT.
External override
Override input: voltage free contact
0.34mm² for total cable length 0-100m
Two methods (A or B) for ballast address configuration are
possible:
©, TELETASK, GENT, 2017
Physical address allocation mode:
Close external override input.
Press manual override button for 10sec.
Indication led will start blinking 3 times in repeat. All ballasts
go to 100%. Configuration mode will be terminated after
15min.
Decouple lamp at first ballast to assign address 1.
Reinsert lamp. Ballast will go to 50%. If not repeat step 4.
Repeat step 4 to 5 to assign the rest of the addresses for
the remaining ballasts.
Press manual override button to terminate configuration.
Indication LED will blink fast and all the ballasts will go to
100% > 0% > 100% > 0% > 100%.
Open the external override input.
105
Version March 2017
TELETASK can’t be responsible for potential errors in the data sheets and technical documentation. Changes in the product features can be made at any time, without prior notice
EN
Output interfaces
POWER CONSUMPTION
AUTOBUS
Min. 140mA (DMX or 1 DSI / DALI ballast connected)
+ 2.5mA for every DSI / DALI ballast connected
DALI = Max. 300mA
DSI = Max. 390mA
DMX = Max. 140mA
DIMENSIONS NET | PACKED
72W x 90H x 60D | 180W x 84H x 107D (mm)
WEIGHT NET | PACKED
0.139kg | 0.227kg
ERROR PREVIEW
In Diagnostics
 Lamp defect
 Ballast defect
 Power failure (230V missing)
 Ballast not found
 DALI bus error message (not a single ballast found)
On the interface
 AUTOBUS voltage
 Interface malfunction (+additional information)
 Interface error message (eg. to hot)
 External contact (only with DALI)
 Interface warning (eg. voltage to low)
PACKAGING CONTENT
TDS13620 interface
AUTOBUS connector set + terminating resistor
AUTOBUS Patch cable
STORAGE
Temperature
-20°C to +65°C
Relative humidity
15% to 85%
IP PROTECTION RATE
IP20
OPERATING RANGE
Temperature
0°C to +50°C max.
Relative humidity
5% to 80% at 25°C (no humidity/condense)
©, TELETASK, GENT, 2017
106
Version March 2017
TELETASK can’t be responsible for potential errors in the data sheets and technical documentation. Changes in the product features can be made at any time, without prior notice
EN
Output interfaces
SCHEMATIC DRAWING
©, TELETASK, GENT, 2017
107
Version March 2017
TELETASK can’t be responsible for potential errors in the data sheets and technical documentation. Changes in the product features can be made at any time, without prior notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising