HID EntryProxTM Keypad Reader/Door Access Control

HID EntryProxTM Keypad Reader/Door Access Control
HID EntryProxTM
Keypad Reader/Door
Access Control
KEYPAD
CONTROLLER
ANTENNA
INSERT
SS
PRE XIT
E
TO
FILLER
PIECE
CONTROLLER
BACKPLATE
PROX
MOUNTING
PLATE
4 WIRE HARNESSES
(2) 4 CONDUCTORS
(1) 5 CONDUCTORS
(1) 6 CONDUCTORS
Installation/Programming Manual
www.hidcorp.com
 Copyright 1999
HID, Corp.
EntryProx Installation/Programming Manual
Model Number 4045AGN00, Rev. 1.0
For more information, contact:
HID Corporation
9292 Jeronimo Road
Irvine, CA 92618-1905.
© Copyright 1999
HID Corporation
All Rights Reserved
Published in U.S.A.
Telephone:
Fax:
949-598-1600
800-237-PROX (toll free in U.S.)
949-598-1690 (tech support fax)
949-598-1690 (main fax)
Table of Contents
Foreword
F.1 About this Manual................................................ ix
F.2 Safety Warnings and Cautions........................... ix
F.3 Design Change Disclaimer ................................. ix
F.4 Reproduction Disclaimer .................................... ix
F.5 Technical Support ................................................. ix
F.6 Warranty ................................................................ x
F.7 Items Supplied from the Factory....................... xi
F.8 Items the Installer Must Supply ........................ xi
Chapter 1: Description
1.1 General Description............................................. 1-1
1.1.1 Design Function ............................................ 1-1
1.2 Uses and Installation Configurations............... 1-2
1.3 Inputs/Outputs ..................................................... 1-2
1.4 Unit Capacity........................................................ 1-2
1.5 Operating Modes ................................................ 1-3
1.6 Alarm Output Selection...................................... 1-3
1.7 EntryProx Operation........................................... 1-4
Chapter 2: Installation
2.1 Installation Configurations................................. 2-1
2.2 Other Installation Considerations..................... 2-2
2.2.1 Power Supply/Current Requirements ....... 2-2
2.2.2 Gang Box and Mounting ............................. 2-2
2.2.3 Mounting the Unit on Metal....................... 2-3
2.2.4 RF Interference .............................................. 2-3
EntryProx Installation/Programming Manual
iii
Table of Contents
2.2.5 Wiegand Operation.......................................2-4
2.3 Checking the Cables ............................................2-6
2.4 Mounting the EntryProx Unit............................2-10
2.4.1 Performing a Wall Mounted Installation ...2-10
2.4.2 Performing a Glass Mounted Installation .2-12
2.4.3 Performing a Secure Installation.................2-14
2.5 Wiring the EntryProx Unit..................................2-18
2.5.1 Wiring the AUX Relay for Use as Alarm
Shunt .........................................................................2-18
Wiring the Alarm Shunt Relay ........................2-18
2.5.2 Wiring the AUX Relay for Use as Forced
Door...........................................................................2-20
Wiring the Forced Door Relay.........................2-20
2.5.3 Wiring the AUX Relay for Use as
Propped Door ..........................................................2-22
Wiring the Propped Door Relay .....................2-22
2.5.4 Wiring the Door Contact Input...................2-24
2.5.5 Wiring the REX Switch .................................2-26
2.5.6 Wiring the Main Relay..................................2-28
2.5.7 Removing/Inserting Circuit Boards ............2-30
2.6 Testing the EntryProx...........................................2-31
2.6.1 Testing the Controller/Keypad.....................2-31
Chapter 3: Programming
3.1 Programming from the Keypad.........................3-1
3.1.1 Master Code....................................................3-1
3.1.2 EntryProx Default Settings...........................3-2
3.2 Changing the Main Relay Time.........................3-4
3.3 Resetting the Master Code and System
Defaults Only ..............................................................3-4
3.4 Erasing Entire Memory/Resetting System
Defaults.........................................................................3-5
3.5 Turning Audio Keypress Feedback ON/OFF ...3-5
iv
EntryProx Installation/Programming Manual
Table of Contents
3.6 Turning Visual LED/Keypress Indicator
ON/OFF ....................................................................... 3-6
3.7 Adding New or Changing Existing
Codes/Cards ................................................................ 3-7
3.8 Adding Cards via Batch Entry........................... 3-8
3.9 Programming for BOTH Code and Card........ 3-9
3.9.1 Code/Card Users ........................................... 3-9
3.9.2 Programming User Data,
Command 50, Full Format.................................... 3-10
3.9.3 Quick Program Feature................................ 3-10
3.9.4 Programming Code ONLY Use.................. 3-10
3.9.5 Programming Code AND Card Use.......... 3-11
3.9.6 Programming Card ONLY Use ................. 3-11
3.9.7 Programming Code OR Card ..................... 3-11
3.10 Programming a Toggle User ............................ 3-12
3.11 Programming User Types ................................. 3-13
3.12 Deleting Users .................................................... 3-14
3.13 Using the Printing Features ............................. 3-15
3.13.1 Selecting Transaction Log Information ... 3-15
3.13.2 Printing a Transaction Log......................... 3-16
A. Programming a Transaction Dump
Code .................................................................... 3-17
B. Printing a Transaction Log Manually........ 3-17
3.13.3 Erasing a Transaction Log.......................... 3-19
3.13.4 Printing a Programmed Users List........... 3-19
3.14 Defaulting EntryProx Memory........................ 3-21
3.15 Programming Codes ......................................... 3-23
EntryProx Installation/Programming Manual
v
Table of Contents
Chapter 4: Troubleshooting
4.1
4.2
4.3
4.4
Before Calling HID...............................................4-1
Flow Charts ...........................................................4-4
Performing Power Supply Integrity Test ..........4-7
Correcting Possible Water Problems..................4-10
A. Silicone............................................................4-10
B. Wire Run.........................................................4-10
Chapter 5: Miscellaneous
Information
5. 1. Customer Service Policy....................................5-1
5.2 RMA Policy ............................................................5-2
Appendix A: Users Chart
Index
vi
EntryProx Installation/Programming Manual
List of Illustrations
Figure 2-1
Wiegand Operation Wiring ..............2-5
Figure 2-2
EntryProx Wiring Harness................2-6
Figure 2-3
Figure 2-4
Identifying Pin Connectors ..............2-7
Performing a Wall Mounted
Installation ...........................................2-11
Figure 2-5
Performing a Glass Mounted
Installation ...........................................2-13
Figure 2-6
Performing a Secure Installation .....2-15
Figure 2-7
Wiring the Alarm Shunt Relay ........2-19
Figure 2-8
Wiring the Forced Door Relay .........2-21
Figure 2-9
Wiring the Propped Door Relay......2-23
Figure 2-10 Wiring the Door Contact Input .......2-25
Figure 2-11 Wiring the REX Switch......................2-27
Figure 2-12 Electric Strike (Fail Secure) Wiring
Diagram................................................2-28
Figure 2-13 MagLock (Fail Safe) Wiring
Diagram................................................2-29
Figure 2-14 Removing/Inserting Printed
Circuit Board .......................................2-30
Figure 3-1
Transaction Log...................................3-18
Figure 3-2
Figure 3-3
Programmed User List ......................3-20
Program Button Location on
Main Circuit Board.............................3-21
EntryProx Installation/Programming Manual
vii
List of Illustrations/List of Tables
List of Tables
viii
Table 1-1
EntryProx Specifications ................... 1-5
Table 2-1
EntryProx Pin Connectors................ 2-8
Table 3-1
EntryProx Default Settings............... 3-2
Table 3-2
Table 3-3
EntryProx LED Indicators/
Sounder Operations .......................... 3-3
EntryProx User Types ........................ 3-13
Table 3-4
Program Codes ................................... 3-23
Table 4-1
Troubleshooting Chart....................... 4-2
EntryProx Installation/Programming Manual
Foreword
F.1 About this
Manual
This manual is designed for installers of the HID
EntryProx Standalone Proximity Reader. All installation, wiring, programming, and troubleshooting instructions, illustrations, and other relevant information is contained in this manual.
F.2 Safety
Warnings and
Cautions
When handling the main printed circuit board, to
guard against possible static discharges, touch a
grounded object BEFORE touching the EntryProx
unit. Static shock can render the product unusable.
F.3 Design
Change
Disclaimer
Due to design changes and product improvements,
information in this manual is subject to change without
notice. HID Corporation reserves the right to change
product design at any time, which may subsequently
affect the contents of this manual.
HID assumes no responsibility for any errors that may
appear in this manual. HID will make every reasonable
effort to ensure that this Installation/Programming
Manual is up to date and corresponds with your
shipped EntryProx unit.
F.4 Reproduction
Disclaimer
Neither this manual nor any part of it may be reproduced, photocopied, or electronically transmitted in
any way without the written permission of HID.
F.5 Technical
Support
Should you experience any difficulty installing the
EntryProx unit, please contact your HID representative, or HID at the number listed on page ii.
Before calling HID for installation assistance, refer
to Chapter 4, Troubleshooting. This chapter includes a list
of common system problems, possible causes, and corrective actions plus easy-to-use diagnostic flow charts.
EntryProx Installation/Programming Manual
ix
Foreword
To contact HID’s Technical Support department, call
1-800-237-PROX between 8:00 a.m. - 7:00 p.m. (Pacific
Coast Time), Monday through Friday. Questions can
a l so b e s ubm itte d thro ug h our w e bsite at
www.prox.com.
F.6 Warranty
HID warrants its products to be free from defects in
material and workmanship, when they have been installed in accordance with the manufacturer ’s instructions, and have not been modified or tampered with.
HID does not assume any responsibility for damage or
injury to person or property due to improper care,
storage handling, abuse, misuse, normal wear and tear,
or an act of God.
HID’s sole responsibility is limited to the repair (at
HID’s option) or the replacement of the defective
product or part when sent to HID’s facility (freight
and insurance charges prepaid), after obtaining HID’s
Return Merchandise Authorization. HID will not be
liable to the purchaser or any one else for incidental
or consequential damages arising from any defect in,
or malfunction of, its products.
This warranty shall expire two years after shipping
date for EntryProx Keypads. Except as stated above,
HID makes no warranties, either expressed or implied,
as to any matter whatsoever, including, without limitation to, the condition of its products, their merchantability, or fitness for any particular application.
x
EntryProx Installation/Programming Manual
Foreword
F.7 Items Supplied The following items are supplied from the factory with
the initial EntryProx shipment.
from the Factory
•
F.8 Items the
Installer Must
Supply
Controller with Keypad, Faceplate, Request to Exit
(REX) button (also called the “Filler Piece”), three
Wire Harnesses, and various installation Screws.
For each initial EntryProx unit installation, the installer must supply the following items:
•
•
•
•
•
•
•
•
•
The EntryProx unit works with these four types
of cards:
– Prox Card II
– IsoProx II
– Duo Prox II
– Proxkey FOB
an appropriately rated DC Power Supply (12 VDC)
(filtered and regulated recommended)
the appropriate installation electrical tools
the recommended remote antenna cable
[ALPHA 1174C (22AWG) 4-wire, stranded, unshielded] (this is required ONLY if you choose to
remote the antenna 10 feet away from the keypad/controller)
the Wiegand interface cable [ALPHA 1295C
(22AWG) 5-conductor, stranded, either overall
shield or equivalent] (this is required ONLY if
using a separate Wiegand control panel)
power supply cable (18AWG-22AWG) 2-wire
stranded, shielded (choose heavier gauge as required for long cable run length, or if sharing
power cable with other devices)
door lock cable (18AWG-22AWG) 2-wire stranded,
unshielded
door monitor cable (18AWG-22AWG) 2-wire
stranded, unshielded
REX cable (if using remote switch) 2-wire
stranded, unshielded
EntryProx Installation/Programming Manual
xi
Foreword
F.9 FCC Warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID Number: JQ64045
xii
EntryProx Installation/Programming Manual
Chapter 1:
Description
Chapter 1 provides a general description of the HID
EntryProx Proximity Reader/Keypad Door Access Control.
1.1 General
Description
1.1.1 Design
Function
The HID EntryProx Proximity Reader/Keypad Door
Access Control provides card and/or keypad access
control for a single door. The unit can be installed in
a one-stage configuration (which is typical for most
users) or a higher security, two-stage (or “remote”)
configuration.
In the “secure” (or remote) configuration, the antenna
can be detached and mullion-mounted up to a maximum of 10 feet away from the controller/keypad. For
installation details, see Chapter 2.
The EntryProx unit is compatible with all HID proximity cards, with up to 37 bits. Batch programming can
be done only with 26-bit HID cards. All programming
is performed using the built-in keypad.
These four specific types of users can be programmed
with the EntryProx unit:
•
•
•
•
0-Toggle/latch strike
1-Normal access
2-log Dump
3-Lockout
For convenience, proximity cards can be programmed
efficiently in a “batch” mode. A user-programmable
EntryProx Installation/Programming Manual
1-1
Chapter 1: Description
1.2 Uses and Installation Configurations
strike time of 1-99 seconds plus a “latch/toggle” mode
are included.
1.2 Uses and
Installation
Configurations
The HID EntryProx Proximity Reader/Keypad Door
Access Control is designed specifically for standalone
installations, or for remote locations in conjunction
with a separate on-line Wiegand system. The unit can
be installed either indoors or outdoors; for installation
details, see Chapter 2.
1.3 Inputs/Outputs Two monitor inputs, “Door Position” [Normally Closed
(N.C) dry contact] and “Request to Exit” [REX, Normally Open (N.O.) dry contact] are supplied.
Additionally, these two relay outputs are supplied,
“Strike Relay - Form C,” which switches up to 4A
(Main), and “Aux Relay - Form C,” which switches up
to 1A (Aux).
Data output to an optional Infrared (IR) printer via the
IR interface and Wiegand output for use with a separate central access control panel are also provided onboard the EntryProx unit.
1.4 Unit Capacity
The EntryProx unit can accommodate up to 2,000 users. Each user can have a card/tag, a PIN code, or a
card/tag plus a PIN code. The specific four user access
configurations include (for details, see section 3.9):
•
•
•
•
(1) Code ONLY (command 50)
(2) Code AND Card (command 50 plus present
card to proximity reader)
(3) Card ONLY (via manual programming, command 51)
(4) Code OR Card (command 52)
A maximum of 1,000 time-stamped transactions can be
stored in the EntryProx unit. Each transaction includes
these parameters: Time, Date, User “slot number,” and
event. A complete Transaction Log can be printed to
1-2
EntryProx Installation/Programming Manual
1.5 Operating Modes
Chapter 1: Description
an optional IR printer via the built-in IR interface. For
printing details, see section 3.13. The type of Transaction Log is “First In, First Out.” The oldest transaction
gets deleted when the new one is added.
1.5 Operating
Modes
During initial installation, the installer programs the
Entr yProx unit for EITHER “Standalone” OR
“Wiegand” mode operation. Only ONE operating
mode can be selected at any one time. If you desire
Standalone mode (the default, out-of-the-box, mode),
no programming is required.
•
In “Standalone” mode, all decisions to open the
door remain with the EntryProx unit, and Wiegand
output is turned OFF.
•
In “Wiegand” mode, the card data is sent to the
separate Wiegand central panel. This panel then
make s all d oor open/ clo se d e cisions and
lights/turns off the EntryProx LEDs accordingly.
In both operating modes, the EntryProx unit maintains
programmability so that EntryProx system parameters
can be set. The default factory setting during programming is for the unit to “time out” after 45 seconds of
inactivity.
1.6 Alarm Output
Selection
During initial installation, the EntryProx unit’s AUX
relay output is wired to trigger ONE of three events.
Consequently, the installer must know which of these
events is appropriate for each installation.
•
Alarm Shunt Relay
•
Forced Door Relay
•
Propped Door Relay
Separate instructions and wiring diagrams for each of
the above applications are provided in Chapter 2.
EntryProx Installation/Programming Manual
1-3
Chapter 1: Description
1.7 EntryProx Operation
NOTE: The capability provided by the internal local
sounder (an audible alarm) is separate from the 1A
AUX relay. The sounder can trigger regardless of
how the AUX relay is programmed.
1.7 EntryProx
Operation
Once installed and programmed successfully, in standalone mode, the EntryProx controller stores all transactions and controls all outputs. The controller receives
data sent to it from the proximity reader, decides if
access should be provided or not, and then energizes
the door lock or not, locking or unlocking the door. (If
the EntryProx unit is programmed for “Wiegand”
mode, the Wiegand panel makes the access decision
and controls the lock relays, all relay outputs on the
EntryProx unit are disabled.)
The EntryProx includes three relay outputs (two are
located internally), an internal clock, programming
keypad, and memory chips to store user information
and a transaction data log.
An external IR (infrared) LED/port/transmitter at the
top right of the EntryProx controller allows for printing
of the Transaction Log and the Programmed User List
to an optional hand-held IR printer. Section 3.13 discusses printing reports.
1-4
EntryProx Installation/Programming Manual
1.7 EntryProx Operation
Chapter 1: Description
Table 1-1. EntryProx Specifications
ELECTRICAL
Power Supply/Current
Requirements
10-15 VDC, linear filtered and regulated power supply
recommended (not including door locking device or
peripherals); 500 mA
WIRING
Remote Antenna Cable
ALPHA 1174C (22AWG) 4-wire, stranded, unshielded
(this is required ONLY if you choose to remote the
antenna 10 feet away from the keypad/controller)
Wiegand Interface Cable
ALPHA 1295C (22AWG) 5-conductor, stranded, either
overall shield or equivalent (this is required ONLY if
using a separate Wiegand control panel)
Power Supply Cable
18AWG - 22AWG 2-wire stranded, shielded (depends
upon distance)
Door Lock Cable
18AWG - 22AWG 2-wire stranded, unshielded
(depends upon distance)
Door Monitor Cable
18AWG - 22AWG 2-wire stranded, unshielded
(depends upon distance)
REX Cable
(if using remote switch) 2-wire stranded, unshielded
MECHANICAL
Height
5.25 in (13.3 cm)
Width
2.75 in (7 cm)
Depth
1.375 in (3.5 cm)
RELAY OUTPUTS
Main Relay - Form C (switches up to 4A)
Aux Relay - Form C (switches up to 1A)
MONITOR INPUTS
Door Position (Normally Closed, dry contact)
Request to Exit (REX, Normally Open, dry contact)
EntryProx Installation/Programming Manual
1-5
Chapter 1: Description
1.7 EntryProx Operation
OTHER OUTPUTS
Infrared output to optional IR printer
Wiegand output to separate control panel
SOUNDER
4000 Hz, defeatable
LEDs
Bi-Color (red/green)
Amber
COMPATIBLE
PROXIMITY CARDS
All HID cards up to 37 bits, including the following:
Prox Card II
IsoProx II
Duo Prox II
Proxkey FOB
UNIT CAPACITY
Users
2,000 users maximum; each user can have a
card/tag, a PIN code, or a card/tag PLUS a PIN code
Transactions
1,000 transactions maximum; each transaction
includes time, date, user “slot number,” and event
Strike Time
1-99 seconds
Strike Mode
Access Time or Toggle/Latch
ALARM OUTPUT
One of three functions can be wired: Alarm Shunt
Relay, Forced Door Relay, or Propped Door Relay
1-6
EntryProx Installation/Programming Manual
Chapter 2: Installation
Chapter 2 contains detailed installation procedures
and wiring diagrams for the HID EntryProx Proximity
Reader/Keypad Door Access Control.
NOTE: HID recommends that first-time installers
test the EntryProx unit BEFORE actually mounting
and wiring the unit to become familiar with its operation (see section 2.6).
2.1 Installation
Configurations
It is the installer ’s responsibility to determine the appropriate EntryProx installation configuration, which
differs from installation to installation. These three
installation configurations are possible:
•
Wall mounted installation (exterior to the room to
be accessed). In this configuration, a single gang
electrical box can be used. Typically, the EntryProx
unit is wall mounted (surface mounted) outside
the access area on the unsecured side.
•
Glass mounted installation, using the four HIDsupplied pressure-sensitive adhesive pads. In this
configuration, the EntryProx unit is affixed with
the adhesive pads to the glass door or the window
adjacent to the door being accessed, on the interior
side of the glass. The side cut-out on the unit is
used to bring the wires out of the side of the EntryProx case.
•
Secure installation (or “two-stage” configuration),
for higher security. In this configuration, the EntryProx antenna is located a maximum of 10 feet
away from the controller/keypad; the controller/keypad is located on the secure side of the door.
EntryProx Installation/Programming Manual
2-1
Chapter 2: Installation
2.2 Other
Installation
Considerations
2.2.1 Power
Supply/Current
Requirements
2.2 Other Installation Considerations
Sections 2.2.1 - 2.2.5 describe important considerations the installer must decide upon before actually
starting to install and wire the EntryProx unit.
Power for the EntryProx unit must be from a minimum
10-15 volt DC linear, filtered and regulated power supply. It is typical for the chosen power supply to power
BOTH the EntryProx unit and the selected locking
device. When using one power supply for both the
EntryProx unit and locking device, be sure to include
both devices in your current requirements calculations.
NOTE: HID recommends that you ground the
power supply to earth ground.
2.2.2 Gang Box
and Mounting
2-2
For the wall mounted installation configuration, a single gang electrical box can be used. (Typically, the EntryProx unit is wall mounted outside the access area
on the unsecure side of the door.)
EntryProx Installation/Programming Manual
2.2 Other Installation Considerations
2.2.3 Mounting the
Unit on Metal
2.2.4 RF Interference
Chapter 2: Installation
The EntryProx unit uses radio frequency to transfer
power to and communicate with the proximity card
or keytag. If the antenna is mounted directly on a metal
building or wall, some of the energy is absorbed by
the metal, resulting in less power being transmitted to
the keytag; this causes reduced read range. If you must
mount the EntryProx unit on metal, test the unit in
place before permanently installing it. If read range
distance distance is not adequate, a non-metallic spacer
can be fabricated and installed between the unit’s antenna and the metal mounting surface.
The EntryProx unit should not cause interference to
other equipment as it is designed to meet FCC guidelines. However, other devices can interfere with EntryProx operation.
Avoid locating the EntryProx unit closer than 3 feet (1
meter) to a computer monitor or television or another
EntryProx unit. If you believe you are experiencing
reduced read range due to interference, try repositioning the EntryProx unit, remoting the antenna, or relocating other nearby electrical equipment.
EntryProx Installation/Programming Manual
2-3
Chapter 2: Installation
2.2.5 Wiegand
Operation
2.2 Other Installation Considerations
If the EntryProx unit is to be operated in conjunction
with a separate Wiegand central access panel, the following features are not accessible:
•
the EntryProx unit does not make any decisions
about unlocking or locking the door
•
the main relay (on the P1 Pin connector) is turned
OFF and inoperable; it does not function, for example, when a code is entered
•
the auxiliary relay (on the P2 Pin connector) is
turned OFF and inoperable
•
the ability of the EntryProx unit to store codes in
memory is turned OFF and inoperable; the EntryProx unit sends card data ONLY to the Wiegand
panel, not code data; it sends the exact data from
the card without any processing of the data; the
PIN keypad does not transmit data to the Wiegand
output
During Wiegand operation, only Pin connector P3 is
used; this is the top, middle, 4-pin connector as shown
in Figure 2-1. Pin connector P2 (a 6-pin connector) is
not used. Figure 2-3 shows all the Pin connectors.
A label on Pin connector P3 specifies which Wiegand
panel terminals to use for the P3 wires. (The BROWN
wire is for Wiegand LED control, the WHITE wire is
for Data 1, and the GREEN wire for Data 0; the BLUE
wire is not used.)
Pin connector P4 at the bottom of the main circuit
board is a 4-pin connector that controls the bi-colored
LED and the antenna on the unit.
2-4
EntryProx Installation/Programming Manual
2.2 Other Installation Considerations
Chapter 2: Installation
WIEGAND OPERATION
BLUE
BROWN
WHITE
+V
GND
GREEN
P1
P3
P2
P4
Figure 2-1 Wiegand Operation Wiring
EntryProx Installation/Programming Manual
2-5
Chapter 2: Installation
2.3 Checking the
Cables
2.3 Checking the Cables
Figure 2-2 below provides a detailed illustration of the
EntryProx’s wiring harness. Figure 2-3 illustrates the
Pin connectors on the main circuit board; Table 2-1
describes these four Pin connectors, P1, P2, P3, and P4.
WIRING HARNESS/
CABLE CROSS-SECTION
P1
1-GREEN
2-GRAY
3-BLUE
4-BROWN
5-ORANGE
6-WHITE
P2
1-GRAY
2-GREEN
3-BLUE
4-BLACK
5-RED
Figure 2-2 EntryProx Wiring Harness
2-6
EntryProx Installation/Programming Manual
2.3 Checking the Cables
Chapter 2: Installation
1-BLUE (NOT USED)
2-BROWN (WIEGAND LED CONTROL)
3-WHITE (WIEGAND DATA 1)
4-GREEN (WIEGAND DATA 0)
IDENTIFYING Pins
1-GREEN (AUX RELAY N/O)
2-GRAY (AUX RELAY N/C)
3-BLUE (AUX RELAY C)
4-BROWN (REX LOOP)
5-ORANGE (DOOR LOOP)
6-WHITE (LOOP COMMON)
1-GRAY (MAIN RELAY N/C)
2-GREEN (MAIN RELAY N/O)
3-BLUE (MAIN RELAY C)
4-BLACK (-V OUT)
5-RED (+V IN)
P1
P3
P2
P4
1-RED (BI COLOR LED)
2-BLACK (BI COLOR LED)
3-WHITE (ANTENNA +)
4-WHITE (ANTENNA -)
Figure 2-3 Identifying Pin Connectors
EntryProx Installation/Programming Manual
2-7
Chapter 2: Installation
2.3 Checking the Cables
Table 2-1. EntryProx Pin Connectors
Pin Connector (on
main circuit board)
Description/Use
P1 (5-pin connector, top
left-most location)
Pin
1
Wire Color
GRAY
2
GREEN
3
4
5
BLUE
BLACK
RED
Use
Main Relay, Normally
Closed (N.C.)
Main Relay, Normally
Open (N.O.)
Main Relay, Common
Ground
Power In, +12 VDC
P3 (4-pin connector,
Wiegand operation, top
middle location)
Pin
1
2
3
4
Wire Color
BLUE
BROWN
WHITE
GREEN
Use
Not used
Wiegand LED Control
Wiegand Data 1
Wiegand Data 0
P2 (6-pin connector, top
right-most location)
Pin
1
2
3
4
5
6
Wire Color
GREEN
GRAY
BLUE
BROWN
ORANGE
WHITE
Use
Aux Relay N.O.
Aux Relay N.C.
Aux Relay Common
REX Loop (if used)
Door Loop Contact
Loop Common (shared by
REX and door loop)
NOTE: Pins 1, 2, 3 can be wired at the installer’s
option for one of the following alarm outputs, Alarm
Shunt, Forced Door, or Propped Door.
P4 (4-pin connector,
bottom location)
Pin
1
2
3
4
Wire Color
RED
BLACK
WHITE
WHITE
2-8
Use
Bi-Color LED (Red +)
Bi-Color LED (Green +)
Antenna +
Antenna -
EntryProx Installation/Programming Manual
2.3 Checking the Cables
Chapter 2: Installation
This page is left blank intentionally.
EntryProx Installation/Programming Manual
2-9
Chapter 2: Installation
2.4 Mounting the EntryProx Unit
2.4 Mounting the
EntryProx Unit
Select one of these three installation configurations,
wall mount, glass mount, or secure as appropriate for
this installation. Then refer to sections 2.4.1 - 2.4.3.
2.4.1 Performing a
Wall Mounted
Installation
This section provides general considerations when
performing a wall mounted installation. Typically, the
EntryProx unit is mounted on a flat, level surface (drywall, masonry, wood, etc.) exterior to the room to be
accessed. A single-gang electrical box (or “back box”)
can be used. Typically, the EntryProx unit is wall
mounted outside the access area on the unsecure side
of the door.
Figure 2-4 illustrates the components on the EntryProx
unit used for wall mounting. Two “single-gang box”
holes align with two corresponding holes in the single-gang box. A “wire” exit knockout is supplied
through which the EntryProx wiring is pulled. A typical wall mounted installation proceeds as follows:
1.
2.
3.
4.
5.
6
7.
2-10
Secure a single-gang box to the desired location.
“Punch out” the two single-gang box connectors
on the controller backplate of the EntryProx unit.
Disconnect the controller backplate of the EntryProx unit from the front keypad/controller.
Align the two single-gang box connectors on the
controller backplate over the two corresponding
holes on the single-gang box, previously secured
at step 1.
Secure the backplate to the single-gang box by
inserting/tightening two screws into the two single-gang box holes.
Connect the front keypad/controller to the back
housing.
Pull the EntryProx wiring through the wiring exit
as appropriate.
Install the tamper screw into the hole at the bottom
front of the enclosure using a #6 spanner bit (not
included, but available from HID).
EntryProx Installation/Programming Manual
2.4 Mounting the EntryProx Unit
Chapter 2: Installation
WALL MOUNT INSTALLATION
3
WIRING
EXITS
SINGLE
GANG BOX
HOLES
CONTROLLER
BACKPLATE
Figure 2-4 Performing a Wall Mounted
Installation
EntryProx Installation/Programming Manual
2-11
Chapter 2: Installation
2.4.2 Performing a
Glass Mounted
Installation
2.4 Mounting the EntryProx Unit
Figure 2-5 shows the four HID-supplied pressure-sensitive adhesive pads and the two side cut-outs used
for this installation. In this configuration, the EntryProx
unit is affixed with the four self-adhesive pads to the
glass or the glass window adjacent to the controlled
door being accessed, on the interior side of the glass.
One of the two side cut-outs is used to bring the wires
out of the side of the EntryProx case.
A typical glass mounted installation proceeds as follows:
1.
2.
3.
4.
5.
6.
2-12
Disconnect the back housing from the front keypad/controller. Remove the tape from the four
self-adhesive pads on the back housing and apply
the pads to the four corners of the backplate.
Affix the back housing to the glass door or the
glass window adjacent to the controlled door being accessed, on the interior side of the glass.
Determine which of the two side cut-outs on the
back housing to use for the wiring and “cut out”
that cut-out using the appropriate cutting tool.
Pull the wiring through the selected side cut-out
as required.
Connect the front keypad/controller to the back
housing.
Install the tamper screw into the hole at the bottom
front of the enclosure using a #6 spanner bit (not
included, but available from HID).
EntryProx Installation/Programming Manual
2.4 Mounting the EntryProx Unit
Chapter 2: Installation
GLASS MOUNT INSTALLATION
4
PRESSURESENSITIVE
PADS ON THE
BACKSIDE OF
BACKPLATE
2
SIDE
CUT-OUTS
Figure 2-5 Performing a Glass Mounted
Installation
EntryProx Installation/Programming Manual
2-13
Chapter 2: Installation
2.4.3 Performing a
Secure Installation
2.4 Mounting the EntryProx Unit
In this configuration, the EntryProx sensor housing is
removed from the keypad/controller and located a
maximum of 10 feet away. The controller/keypad is
located inside a secure area.
1.
•
•
When handling the main printed circuit board, to
guard against possible static discharges, touch a
grounded object BEFORE touching the EntryProx
unit. Remove the main printed circuit board by
pressing the two spring tabs in the direction of the
arrows as shown in Figure 2-13. Be careful with
the wires.
•
Fold up the main circuit board and remove Pin
connector P4 (a 4-pin connector) from the bottom
of the main board. A ribbon cable now holds the
main board to the keypad board. DO NOT pull
this ribbon cable out of its connector! Once the
main board is removed, you can access the interior
of the antenna.
•
Remove the antenna housing from the keypad/controller by pressing the labeled four secure
tabs inward (see Figure 2-6) until the sensor housing “pops out.”
2.
Prepare the wiring and extension wiring as follows:
Cut off the plastic end of the EntryProx sensor
housing harness.
•
•
2-14
Remove the antenna from the EntryProx keypad/controller as described below:
Disconnect the backplate of the EntryProx unit
from the front keypad/controller.
Splice the recommended remote antenna cable Alpha 1174C (22AWG), 10-foot maximum length, to
the properly cut antenna cable using standard electrical techniques.
EntryProx Installation/Programming Manual
2.4 Mounting the EntryProx Unit
Chapter 2: Installation
REMOTE INSTALLATION SITE
SECURE INSTALLATION SITE
MAX. 10 FEET
FROM KEYPAD/
CONTROLLER
REMOVE ANTENNA FROM
KEYPAD/CONTROLLER BY
PRESSING FOUR SECURE
TABS INWARD UNTIL
ANTENNA POPS OUT
2 WIRING
EXITS
ANTENNA
BACKPLATE
4 EXTERNAL
CUT-OUTS
(MATCH SPRINGLOADED TABS)
4 SPRINGLOADED TABS
2 SCREW
HOLES
PROX
SENSOR
HOUSING
2 OPTIONAL
SIDE BREAK-OUTS
2 WEEP HOLES
REVERSE
VIEW OF
FILLER
PIECE
FILLER PIECE/
REX OPERATION
DOGBONE
2 TABS
REMOVED
FOR REX
OPERATION
FILLER
PIECE
DECIDE BETWEEN
REPLACING WITH
FILLER PIECE AND
REX OPERATION
"PRESS TO EXIT"
LABEL (APPLIED
AFTER INSTALLATION)
IF USED AS A REX
BUTTON
Figure 2-6 Performing a Secure Installation
EntryProx Installation/Programming Manual
2-15
Chapter 2: Installation
2.4 Mounting the EntryProx Unit
3.
•
Mount the antenna backplate in a vertical orientation and secure it to the wall through the two
screw holes using two HID-provided screws. Ensure that the two “weep holes,” provided to remove possible moisture, are positioned on the
bottom. “Punch out” one or both wiring exits on
the front of the antenna backplate and pull the
antenna wire through as required. (Four external
cut-outs on the antenna backplate match the four
spring-loaded tabs on the antenna.)
NOTE: Two side cut-outs are furnished on the
antenna backplate for the wiring, if the installation
does not permit the wiring to run through the
wall. These must be “cut out” to be used.
Once the antenna backplate is mounted properly,
align the antenna to the backplate and connect the
antenna to the antenna backplate. The large tab in
the center of the antenna assembly must be broken
off before being attached to the antenna backplate.
4.
Run the antenna wiring back to the secure keypad/controller and connect it to the main circuit
board, using the 10-inch 4-wire harness (red, black
and white) that you plug into connector P4 on the
controller board. Connect the red of the antenna
to the red of the P4 harness, etc. Seal the wire
holes with silicone.
5. Select “Filler” or “Request to Exit” (REX) operation
as follows:
• If you elect to use the filler piece as a REX switch,
return to the keypad/controller and break off two
tabs on the filler piece as illustrated in Figure 2-6.
The filler piece replaces the antenna on the front
of the keypad/controller for secure installations.
•
2-16
If the filler piece is not be be used as a REX switch,
DO NOT remove the two tabs.
EntryProx Installation/Programming Manual
2.4 Mounting the EntryProx Unit
Chapter 2: Installation
•
Select “Filler or “REX” operation and affix the appropriate HID-provided label to the filler piece.
For Filler operation, no tabs are broken off the filler
piece, which merely sits in place of the remotely
located antenna, once the main circuit board and
cabling are replaced.
For REX operation, break off the labeled tabs,
which allows a spring-loaded tab to engage the
REX switch on the main circuit board and open
the door.
•
Replace the main circuit board into the keypad/controller and Pin connector P4 to the main
circuit board.
•
Connect the front keypad/controller of the unit to
the back housing.
•
Secure with a tamper screw.
EntryProx Installation/Programming Manual
2-17
Chapter 2: Installation
2.5 Wiring the
EntryProx Unit
2.5.1 Wiring the AUX
Relay for Use as
Alarm Shunt
2.5 Wiring the EntryProx Unit
Select one of these three wiring options, Alarm Shunt,
Forced Door, or Propped Door, depending on how the
EntryProx’s alarm output is to be employed for this
installation. Then refer to sections 2.5.1 - 2.5.3 as appropriate.
The Alarm Shunt Relay function may be necessary
when a separate existing security system is in place.
The Alarm Shunt Relay keeps an alarm panel zone
from going into alarm when the door is opened, after
a valid code is entered. No programming is required
for a new unit out-of-box, or if the unit is ever defaulted
using programming commands 40# and 46#. The EntryProx controller assigns the AUX relay to the Alarm
Shunt Relay automatically upon any valid access or
egress. To incorporate this feature, follow the steps
below; see Figure 2-7.
Wiring the Alarm Shunt Relay
1.
2.
3.
4.
5.
6.
2-18
Turn OFF power to the EntryProx unit, and then
unlatch the keypad from the plastic housing.
Locate connector P2 (the 6-pin connector) on the
main circuit board and plug on the 6-pin harness.
(The 2-pin jumper on pins 5 and 6 of connector
P2 must be removed first.)
Connect the 6-conductor harness to connector P2
as shown in Figure 2-7.
Connect the green wire to the “Common” side of
the door contact.
Connect the blue wire to the “Normally Open”
side of the door contact.
Make a parallel connection to the green and blue
wires and run the leads to the alarm panel. NOTE:
This feature requires that you use the “Door Contact” input as shown in Figure 2-7.
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
ALARM SHUNT RELAY
TO ALARM PANEL
DOOR
CONTACT
GOING BACK
TO ALARM
PANEL
BLUE (C)
TO ALARM PANEL
ORANGE
GREEN
(N/O)
P1
P3
P2
SEPARATE DOOR
CONTACT BEING
MONITORED BY
PROX PAD
WHITE
P4
Figure 2-7 Wiring the Alarm Shunt Relay
EntryProx Installation/Programming Manual
2-19
Chapter 2: Installation
2.5.2 Wiring the AUX
Relay for Use as
Forced Door
2.5 Wiring the EntryProx Unit
The Forced Door output function informs personnel
that the door has been opened without authorization.
The Aux relay is rated to handle one amp of current
at 12 VDC, and can turn ON or OFF one leg of the
power to a warning device. (Warning device not included with the HID unit.) To incorporate this feature,
follow the steps below; see Figure 2-8.
Wiring the Forced Door Relay
1.
2.
3.
4.
5.
6.
Turn OFF power to the EntryProx unit, and then
unlatch the keypad from the plastic housing.
Locate connector P2 (the 6-pin connector) on the
main circuit board.
Connect the 6-conductor harness to connector P2.
(The 2-pin jumper on pins 5 and 6 of connector
P2 must be removed first.)
Connect the green wire to V+ on the warning
device.
Connect the blue wire to V+ on the power supply.
Connect V- from the power supply to V- on the
sounder. The gray wire is not used.
NOTE: To use the default 10-second Forced Door
Relay time, no programming is necessary. To change
this default (from 10 to 900 seconds), enter the appropriate programming after the unit is installed
successfully; for details, see Chapter 3.
NOTE: PROGRAMMING FOR FORCED DOOR
To program for Forced Door, enter the following
on the keypad: 15 # 2 # 0 # **
2-20
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
FORCED DOOR RELAY
TO POWER SUPPLY
V+
V+
V+
BLUE
(C)
GREEN
(NO)
P1
P3
P2
P4
Figure 2-8 Wiring the Forced Door Relay
EntryProx Installation/Programming Manual
2-21
Chapter 2: Installation
2.5.3 Wiring the AUX
Relay for Use as
Propped Door
2.5 Wiring the EntryProx Unit
The Propped Door Relay output function informs personnel that the door is being held open, or “propped”
open, after a valid entry. The Aux relay is rated to
handle one amp of current at 12 VDC, and turns ON
or OFF one leg of the power to a warning device.
(Warning device not included with the HID unit.) To
incorporate this feature, follow the steps below; see
Figure 2-9.
Wiring the Propped Door Relay
1.
2.
3.
4.
5.
6.
Turn OFF power to the EntryProx unit, and then
unlatch the keypad from the plastic housing.
Locate connector P2 (the 6-pin connector) on the
main circuit board.
Connect the 6-conductor harness to connector P2.
(The 2-pin jumper on pins 5 and 6 of connector
P2 must be removed first.)
Connect the green wire to V+ on the sounder.
Connect the blue wire to V+ on the power supply.
Connect V- from the power supply to V- on the
sounder. The gray wire is not used.
NOTE: To use the default 10-second Propped Door
Relay time, no programming is necessary. To change
this default (from 10 to 900 seconds), enter the appropriate programming after the unit is installed
successfully; for details, see Chapter 3.
NOTE: PROGRAMMING FOR PROPPED
DOORTo program for Propped Door, enter the
following on the keypad: 15 # 3 # 0 # **
2-22
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
PROPPED DOOR RELAY
TO POWER SUPPLY
V+
V+
V+
BLUE
(C)
GREEN
(NO)
P1
P3
P2
P4
Figure 2-9 Wiring the Propped Door Relay
EntryProx Installation/Programming Manual
2-23
Chapter 2: Installation
2.5.4 Wiring the Door
Contact Input
2.5 Wiring the EntryProx Unit
To solve the problem of people “tailgating” in behind
personnel using valid access protocol, the Auto ReLock feature is provided. With Auto Re-Lock, a long
door open time can be programmed. Auto Re-Lock
overrides the main relay timer, resetting the door open
time as soon as the EntryProx unit senses that the door
is open. A long door open time allows people sufficient
time to carry packages from the proximity reader/keypad to the door and open it before the timer runs out.
No programming is required to implement this feature.
After a valid access or egress, the EntryProx unit senses
that the door switch is open and drops the main relay
immediately. This disengages the lock, which locks
behind the person regardless of how long it takes that
person to get through the door.
NOTE: This feature requires that you use the “Door
Contact” input as shown in Figure 2-10.
2-24
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
DOOR CONTACT
ORANGE
DOOR
CONTACT
P1
P3
P2
WHITE
P4
Figure 2-10 Wiring the Door Contact Input
EntryProx Installation/Programming Manual
2-25
Chapter 2: Installation
2.5.5 Wiring the REX
Switch
2.5 Wiring the EntryProx Unit
The EntryProx unit can be wired to monitor a remote
switching device, which is intended to be installed on
the “safe” side of a door. The Request to Exit (REX)
switch is a momentary input that engages the main
relay for the same length of time for which the main
relay is programmed. This feature can be stored in the
Transaction Log for viewing.
If you elect to perform a secure installation where the
controller is mounted on the secure side of the door,
you can use the filler piece as a REX switch, thereby
decreasing the cost of the installation. For other installations, a separate REX switch must be purchased.
Other REX devices include a remote button placed at
a receptionist’s desk, a press-to-exit switch on the inside of a door, or a passive infrared detector, allowing
free and convenient egress. The REX feature requires
no programming; simply wire the unit as illustrated
in Figure 2-11. To incorporate this feature, follow the
steps below:
1.
2.
3.
4.
Turn OFF power to the EntryProx unit, and then
unlatch the keypad from the plastic housing.
Locate connector P2 on the main circuit board.
Plug the 6-conductor harness into connector P2.
(The 2-pin jumper on pins 5 and 6 of connector
P2 must be removed first.)
If you do not wish to install the door contacts per
Figure 2-11, twist the white wire and the orange
wires together; this is mandatory. If this is not
done, the REX input will not function.
NOTE: The door contact MUST be closed for the
REX feature to work properly.
2-26
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
REQUEST TO EXIT
(WITH DOOR CONTACT)
REQUEST TO EXIT
(NO DOOR CONTACT)
ORANGE
BROWN
P1
P3
P2
ORANGE
NORMALLY
OPEN
SWITCH
WHITE
BROWN
P1
P3
P2
WHITE
NORMALLY
OPEN
SWITCH
DOOR
CONTACT
P4
P4
Figure 2-11 Wiring the REX Switch
EntryProx Installation/Programming Manual
2-27
Chapter 2: Installation
2.5.6 Wiring the Main
Relay
2.5 Wiring the EntryProx Unit
The door lock is wired to connector P1 on the EntryProx main circuit board. Wiring for this 5-pin connector is described in Table 2-1, Figure 2-12 provides
an Electric Strike (Fail Secure) wiring diagram, Figure
2-13 a MagLock (Fail Safe) wiring diagram. Refer to
the power supply recommendations in section 2.2.1 if
necessary.
LOCK WIRING DIAGRAM
STRIKE
(FAIL-SECURE)
VV+
BLACK
(V- )
POWER
SUPPLY
BLUE
(MAIN RELAY C)
GREEN
(MAIN RELAY N/O)
RED
(V+ IN)
P1
P3
P2
P4
Figure 2-12 Electric Strike (Fail Secure) Wiring
Diagram
2-28
EntryProx Installation/Programming Manual
2.5 Wiring the EntryProx Unit
Chapter 2: Installation
MAGLOCK
(FAIL SAFE)
VV+
BLACK
(V- )
POWER
SUPPLY
BLUE
(MAIN RELAY C)
GRAY
(MAIN RELAY N/C)
RED
(V+ IN)
P1
P3
P2
P4
Figure 2-13 MagLock (Fail Safe) Wiring Diagram
EntryProx Installation/Programming Manual
2-29
Chapter 2: Installation
2.5 Wiring the EntryProx Unit
2.5.7
Removing/Inserting
Circuit Boards
If it proves necessary to remove or insert the main
circuit board from/into the EntryProx controller/keypad, follow the steps below.
1.
2.
Disconnect the back housing of the EntryProx unit
from the front keypad/controller.
(When handling the main printed circuit board,
to guard against possible static discharges, hold
the board by its edges with one hand and then
touch a grounded object BEFORE touching the
EntryProx unit.) Remove the main printed circuit
board by pressing the two spring tabs in the direction of the arrows as shown in Figure 2-14. Be
careful with the wires.
REMOVE/INSERTING PCB
FRONT
HOUSING
ASSEMBLY
PUSH TABS IN
DIRECTION OF
ARROWS TO REMOVE
REVERSE
TO RE-INSERT
Figure 2-14 Removing/Inserting Printed Circuit
Board
3.
2-30
Fold up the main circuit board and remove the P4
connector (a 4-conductor harness) from the bottom of the board.
EntryProx Installation/Programming Manual
2.6 Testing the EntryProx
Chapter 2: Installation
4.
5.
2.6 Testing the
EntryProx
To re-insert, replace the main circuit board into
the keypad/controller and the P4 connector to the
main circuit board.
Connect the keypad/controller to the back housing.
At this point in a typical installation, it is assumed that
the EntryProx unit has been mounted and wired successfully as described earlier and that testing can begin.
HID recommends, however, that first-time installers
test the EntryProx unit BEFORE actually mounting
and wiring the unit to become familiar with its operation.
2.6.1 Testing the
Controller/Keypad
1.
2.
3.
4.
5.
6.
Connect the positive (+) lead of the power supply
to the V+ input on the controller/keypad.
Connect the negative (-) lead of the power supply
to the V- input on the controller/keypad.
Turn ON the power supply.
Ensure that the bi-color LED (red and green) on
the EntryProx unit lights red.
On the EntryProx controller/keypad, press:
7890 # 123456 *
If all 12 key presses are verified, the EntryProx
unit enters the self-test mode. The bi-color LED
turns green. The red LED blinks alternately with
the yellow LED and then both turn OFF. Next, the
sounder beeps three times, pauses, and then beeps
once more. If this does not occur, attempt to enter
the self-test mode again by repeating step 5.
Enter the master code on the keypad by pressing:
99 # Master Code * (default is 1234)
The red LED turns OFF and the green LED turns
ON for five seconds while the main relay energizes. To program the unit, see Chapter 3.
EntryProx Installation/Programming Manual
2-31
Chapter 3:
Programming
Chapter 3 provides information about programming
the HID EntryProx unit. Certain parameters must be
programmed upon initial installation, such as changing the default Master Code (section 3.20.) Section
3.14 describes how to default the memory, to recover
from possible static discharges, which may be required.
3.1 Programming
from the Keypad
3.1.1 Master Code
The first step in programming the EntryProx unit is to
place it into program mode. You can verify that the
unit is in program mode as the yellow LED blinks
slowly; when the yellow LED stops blinking and is
OFF completely, the unit is no longer in program
mode. If the desired programming is not understood
by the unit or is entered incorrectly, the yellow LED
remains steadily lighted; this signals that you should
press * to clear the error condition and then re-enter
the code. If the unit does not go into program mode,
refer to the Troubleshooting Chart in Chapter 4.
To place the unit in program mode, you must first enter
99 # followed by the “master code,” which is the code
that is stored in the user slot. (If you forget the master
code, pressing the SW 1 or Program button on the main
circuit board accomplishes the same thing. See the
second problem/solution in Table 4-1 for details.)
To place the EntryProx unit in program mode, press:
99 # Master Code *
NOTE: 1234 is the default master code, which HID
recommends you change right away.
EntryProx Installation/Programming Manual
3-1
Chapter 3: Programming
3.1 Programming from the Keypad
A slow blinking yellow LED indicates that the unit is
in program mode. A steady yellow LED, in contrast,
means that errors were detected during programming.
Error states can be cleared by pressing the asterisk *
key.
EntryProx user codes consist of a minimum of one digit
and a maximum of six digits. A complete list of program commands is supplied in Table 3-4. Attempting
to enter a user code into memory that had been entered
previously into a different register, causes the yellow
LED to stop blinking and remain steadily lighted. If
this occurs, try entering a different user code. Repeating digits in the same code is acceptable.
It may be necessary to change the default main relay
time upon initial installation. This would allow personnel sufficient time to get from the proximity reader
to the door before the main relay re-locks the door. For
details, see section 3.2.
Table 3-1 lists the default settings for the EntryProx unit
as shipped from the factory. Subsequent sections in
this chapter explain how to change these default settings or program additional functions.
3.1.2 EntryProx
Default Settings
Table 3-1. EntryProx Default Settings
Parameter
Default Setting
Master Code (user one)
1234*
Main Relay energizes for
Five (5) seconds
Audible Keypress Feedback
ON
Local Propped Door Sounder activates after
Thirty (30) seconds
Local Forced Door Sounder activates for
Ten (10) seconds
Printer Output Port
IR (infrared) port
3-2
EntryProx Installation/Programming Manual
3.1 Programming from the Keypad
Chapter 3: Programming
Table 3-2. EntryProx LED Indicators/Sounder Operations
LED or
Sounder
Visual/Audible
Condition
Description
Yellow LED
Slow blink
Unit is in Program mode
Rapid blink
Verify mode is active (checking that the last
two values in sequence match)
Steady
Program error; to clear, press *
Very rapid blink
Memory (eeprom) erase is in progress
(commands 40/46, loop-back)
Steady red
Strike is locked
Steady green
Strike is energized (timed or latched)
Solid green with red
flicker
Strike toggle is unlocked and user lockout
active
Red/green
alternating
Awaiting second PIN during “Card AND
Code” access attempt
Red blink
User lockout is active and strike locked; red
LED drops out for 100 ms every second;
normal users cannot change the state of
the relay
Short beep (100
ms) every 2 seconds
Propped door is active
Sounder 1/2 sec on,
1/2 sec off
Forced door is active
3 rapid beeps after
code entered or
card presented
Code or Card is not found
3 slow beeps (250
ms), then single
beep
Self-test is complete
1 short beep
Valid card access
Bi-color LED
Sounder
EntryProx Installation/Programming Manual
3-3
Chapter 3: Programming
3.2 Changing the
Main Relay Time
3.2 Changing the Main Relay Time
Setting the main relay time for the master code simultaneously sets the time for users in register one through
register two-thousand. The factory default main relay
time is five (5) seconds. Main relay time can be set in
one-second increments from one (1) second to ninety
(99) seconds using command 11.
1.
2.
3.
3.3 Resetting the
Master Code and
System Defaults
Only
Entering command 40 erases everything from the EntryProx memory except the user list and transaction
log and restores the default settings. This is useful if
the EntryProx unit has experienced programming
problems, or wish to delete earlier programming.
1.
2.
3.
3-4
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Enter the new main relay time, in seconds (from
1 to 99). For example, to enter 10 seconds, press:
11 # 10 # 0 # **
The yellow LED continues to blink slowly.
Press * to exit program mode.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Press:
40 # 00000 # 00000 # **
The yellow LED continues to blink slowly.
Press * to exit program mode.
EntryProx Installation/Programming Manual
3.4 Erasing Entire Memory/Resetting System Defaults
3.4 Erasing Entire
Memory/Resetting
System Defaults
Entering command 46 deletes everything from the
EntryProx memory including the user list but not the
transaction log and restores the default settings. This
is used as a last resort if you need to erase a specific
user and could not retrieve the Programmed User List.
1.
2.
3.
3.5 Turning Audio
Keypress
Feedback ON/OFF
Chapter 3: Programming
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Press:
46 # 00000 # 00000 # **
The yellow LED continues to blink slowly.
Press * to exit program mode.
The Audio Keypress Feedback command enables the
sounder to beep once for each key press. This feature
provides an audio acknowledgment that a particular
key was pressed hard enough for the unit to understand. The factory-shipped default setting is ON, but
it can be toggled ON and OFF as desired using command 30. NOTE: A common reason to turn this feature
OFF is to prevent an unauthorized user from hearing
the audio feedback emitted when an authorized user
enters his/her code.
1.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
EntryProx Installation/Programming Manual
3-5
Chapter 3: Programming
3.6 Turning Visual LED/Keypress Indicator ON/OFF
2.
3.
4.
3.6 Turning Visual
LED/Keypress
Indicator ON/OFF
This visual LED/keypress indicator lights the visual
LED once for each key press. This feature provides a
visual acknowledgment that a particular key was
pressed hard enough for the unit to understand. The
factory-shipped default setting is ON, but it can be
toggled ON and OFF as desired. NOTE: A common
reason to turn this feature OFF is to prevent an unauthorized user from viewing visual feedback produced when an authorized user enters his/her code.
1.
2.
3.
4.
3-6
To enable this feature, press:
30 # 0 # 1 # **
The yellow LED continues to blink slowly.
To disable this feature, press:
30 # 0 # 0 # **
The yellow LED continues to blink slowly.
Press * to exit program mode.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
To enable this feature, press:
30 # 1 # 1 # **
The yellow LED continues to blink slowly.
To disable this feature, press:
30 # 1 # 0 # **
The yellow LED continues to blink slowly.
Press * to exit program mode.
EntryProx Installation/Programming Manual
3.7 Adding New or Changing Existing Codes/Cards
3.7 Adding New or
Changing Existing
Codes/Cards
Chapter 3: Programming
The most basic EntryProx programming is adding new
codes or cards (users), or modifying existing codes or
cards (users). Each user entry consists of three or four
data values: a user type, a location and a keypad-PIN,
and/or card.
Two methods can be used for adding new or changing
existing codes/cards, (1) keypress sequences (manual
entry), and (2) card presentations. Keypad PINs can
be programmed only through a keypad sequence,
while card PINs can be programmed manually or by
presenting the card to the proximity reader at a specified time during programming. These four specific
types of users can be programmed with the EntryProx
unit:
•
Toggle/latch strike (0)
•
Normal access (1)
•
log Dump (2)
•
Lockout (3)
NOTE: When 26-bit cards are used and you choose
to add new cards manually, the facility code must
be entered into the unit first. For the programming
sequence used to enter the 3-digit facility code, see
Table 3-4, item 8.
The following procedure adds a new code/card, or lets
you change an existing code/card.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
2. Press the user location number that represents the
user to be added or changed followed by a pound
EntryProx Installation/Programming Manual
3-7
Chapter 3: Programming
3.8 Adding Cards via Batch Entry
3.
3.
4.
3.8 Adding Cards
via Batch Entry
symbol #. For example, user number two would
be entered as 2 #, user two-thousand as 2000 #.
CODE: Enter the one- to six-digit code and an
asterisk *, for example, 5* or 532346*. The yellow
LED blinks rapidly, indicating that you should
verify the new code by entering it again (along
with an asterisk). If the unit accepts the code, the
yellow LED begins blinking slowly.
CARD: Press ** on the keypad and then go to the
proximity reader and present the card.
To add more card or change more cards, return to
step 2.
Press * to exit program mode.
“Batch entry” allows you to enter multiple, sequential
26-bit HID cards into the EntryProx unit’s memory at
one time. (Keeping HID proximity cards in order is
easy as the code is printed on the front of each card.)
NOTE: The facility code must be programmed into
the unit before any batch entry can occur. The facility
code must be programmed only once. For the programming sequence used to enter the 3-digit facility
code, see Table 3-4, item 8.
To add several users from the proximity reader, follow
this procedure:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
3-8
EntryProx Installation/Programming Manual
3.9 Programming for BOTH Code and Card
2.
Chapter 3: Programming
On the EntryProx keypad, press:
56 # (total number of cards to be added) #
(starting user location) # card number *
repeat card number *
NOTE: Never enter one (1) as the starting user
location since it is reserved for the master code.
3.
3.9 Programming
for BOTH Code
and Card
On the EntryProx keypad, press * to exit program
mode.
Up to 1,999 users can be added this way at one
time. (User 1 is reserved for the Master code.)
The EntryProx unit can be programmed to accept the
four code/card combinations listed below.
•
(1) Code ONLY (command 50)
•
(2) Code AND Card (command 50 plus present
card to proximity reader)
(3) Card ONLY (command 50 or command 51)
(4) Code OR Card (command 52)
•
•
NOTE: No user can have the same card and/or code
PIN as another user.
3.9.1 Code/Card
Users
When a combination code/card user employs the EntryProx unit, that user can present the proximity card
first at the proximity reader, or enter the code first at
the EntryProx keypad as desired.
After the code/card user either presents the card at the
reader or enters the code on the keypad, the red and
green LEDs alternate. This indicates that the unit is
awaiting the second part of the transaction before
granting access. After the second part of the transaction
is completed successfully, the bi-color LED turns solid
green and the door opens.
EntryProx Installation/Programming Manual
3-9
Chapter 3: Programming
3.9.2 Programming
User Data, Command
50, Full Format
3.9 Programming for BOTH Code and Card
The full format of command 50 for programming user
data is as follows:
50 # user-type # user location # keypad PIN
* keypad PIN *
Programming a user ’s card with command 50 requires
that you present the card to the proximity reader after
entering the final asterisk *.
A single beep from the sounder indicates that the card
has been read and the data added to the user ’s entry.
If the yellow LED lights steadily after the card is presented, it usually indicates one of two problems: (1)
an improper keypress (correct by entering properly),
or (2) the number entered is in use by another user
(correct by employing an unused PIN and card).
3.9.3 Quick Program
Feature
A “quick program” feature has been implemented for
user data, however. You only need to enter the user ’s
location and the keypad PIN (or present card), in the
format noted below. Employing the quick feature automatically selects a “Normal” user access type.
loc # PIN * PIN *
OR
loc # ** <present card>
3.9.4 Programming
Code ONLY Use
You can program a user Code ONLY use with command 50. The program sequence is as follows:
50 # user-type # user location # keypad PIN
* keypad PIN *
3-10
EntryProx Installation/Programming Manual
3.9 Programming for BOTH Code and Card
3.9.5 Programming
Code AND Card Use
Chapter 3: Programming
The format for programming a user for both Code
AND Card use is as follows:
50 # user-type # user location # keypad PIN
* keypad PIN * <present card>
3.9.6 Programming
Card ONLY Use
Card ONLY use can be programmed with command
50, with the keypad PIN values omitted from the sequence. For instance, to program user 200 as a “Normal” access user with Card ONLY, press:
50 # user-type # user location # **
<present card>
3.9.7 Programming
Code OR Card
Finally, you can program a user for either Code OR
Card use as follows:
52 # user-type # user location # keypad PIN
* keypad PIN * <present card>
EntryProx Installation/Programming Manual
3-11
Chapter 3: Programming
3.10 Programming a Toggle User
3.10 Programming A user can be programmed as a toggle code and/or
card, which provides that user the ability to unlock the
a Toggle User
door for an indefinite period. When a toggle user then
enters the toggle code or card, the EntryProx unit
toggles the relay ON; entering a toggle code again
toggles the relay OFF.
If the main relay is toggled ON/OFF, the event is stored
in the Transaction Log; when printed, the log shows
“TGL ON” or “TGL OFF” as appropriate; also shown
is the time, date, door number, and user. To program
a toggle user, follow the steps below.
1.
2.
3.
4.
5.
3-12
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the
unit is in program mode. A steady yellow LED,
in contrast, means that errors were detected
during programming. Error states can be
cleared by pressing the asterisk * key.
CARD: On the EntryProx keypad, enter:
0 # user location # ** <present card>
where 0 (zero) is the user type.
CODE: on the Proximity keypad, enter:
0 # user location # code * code *
CARD and CODE: enter:
0 # user location # code * code *
<present card>
Press * on the EntryProx keypad to exit program
mode.
EntryProx Installation/Programming Manual
3.11 Programming User Types
Chapter 3: Programming
3.11 Programming Table 3-3 identifies and describes the four user types
supported by the EntryProx unit. NOTE: All examples
User Types
show programming the four user types as card only
users. All four user types can also be programmed as
code only, code and card, and code or card.
Table 3-3. EntryProx User Types
User Type
User-Type
Description
Toggle/latch
strike
00
For this user-type, the door opens for an
indefinite period, until that or another toggle
code is entered (this is useful for deliveries,
for example). Example:
50 # 0 # user location # ** <present card>
Normal access
01
This is the default user type. Opens the door
for the duration of the Main Relay time.
Example:
50 # 1 # user location # ** <present card>
Log Dump
02
For this user-type, the door remains locked
and the Transaction Log is dumped to an
optional IR printer via the IR port when the
appropriate code is entered. This code cannot
be used to gain access through the door. This
log is not erased, only printed. Example:
50 # 2 # user location # ** <present card>
Lockout
03
For this user-type, the keypad “freezes,”
disallowing all other codes plus the door
remains in the current state. During a lockout
state, card access does not continue to work.
If it is locked, it remains locked. If it is
unlocked, it remains unlocked until another
Lockout code is entered, releasing it from
Lockout mode. NOTE: This user-type should
be reserved as a supervisor or override
function. Example:
50 # 3 # user location # ** <present card>
EntryProx Installation/Programming Manual
3-13
Chapter 3: Programming
Users
3.12 Deleting
Users
3.12 Deleting
To delete a user from the EntryProx unit’s memory,
you must know the memory register in which the
information is stored. Printing a Programmed Users
List (as described in section 3.13.4) helps you determine this, if your system is equipped with an optional
IR printer. If not, the programmer should have filled
out a paper chart listing the memory location or register in which all users are stored. For a blank chart
that you can photocopy, see Appendix A.
To delete a user, follow the steps below.
1.
2.
3.
3-14
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
On the EntryProx keypad, enter the user number
you wish to delete and a pound symbol #. To
delete user 100, for example, press:
100 # **
The yellow LED blinks slowly.
Press * to exit program mode.
EntryProx Installation/Programming Manual
3.13 Using the Printing Features
3.13 Using the
Printing Features
3.13.1 Selecting
Transaction Log
Information
Chapter 3: Programming
The EntryProx unit in conjunction with an optional IR
(infrared) hand-held printer can print a Transaction
Log and a Programmed User List via the IR port. The
Log Dump command is 70 # 0 # 0 # **.
You can selectively program specific transaction events
to print or not on the Transaction Log. By “masking”
out certain events, you direct the unit not to save those
events in memory and thus not be available for the
log. The factory default is for all transaction events to
be saved in memory and printed on the log.
To turn OFF an event (keep it from being logged),
enter:
73 # Event Code # 0 # **
To turn an event ON, enter:
73 # Event Code # 1 # **
The following transaction events can be set/cleared
(saved/not saved) and therefore printed/not printed.
Event Code
01
02
03
04
05
06
07
08
09
16
17
20
21
24
25
27
EntryProx Installation/Programming Manual
Transaction Event
Access Denied
Program Denied
Program Mode
REX (Request to Exit)
Door Ajar
Door Closed
Forced Door
Log Erased
Facility Access
Print
Access
TGL ON (Toggle ON)
TGL OFF (Toggle OFF)
Lo ON (Lockout ON)
Lo OFF (Lockout OFF)
MSMTCH (Mismatch on Card and
Code entry)
3-15
Chapter 3: Programming
3.13 Using the Printing Features
1.
2.
3.
3.13.2 Printing a
Transaction Log
3-16
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Press:
73 # event # 0/1 # **
“0/1” in the command syntax is the ON/OFF instruction for the unit. Pressing 0 at a certain event
means that that event is not logged and is not
available to be printed. Pressing 1, in contrast,
restores logging and printing for a particular
event. “Event” is a two-digit number that represents a specific transaction as listed on the previous page.
A steady yellow LED indicates an error; if this
occurs, start again.
Press * to exit program mode.
The yellow LED stops blinking.
If you have an optional IR printer, you can print a
Transaction Log on it via the EntryProx’s IR port. Transaction Logs can be printed using two different methods, (1) by programming a “dump” code into memory
and (2) by placing the EntryProx unit into program
mode and manually entering the print Transaction Log
command. For details, see the sub-sections A and B on
the next page.
EntryProx Installation/Programming Manual
3.13 Using the Printing Features
Chapter 3: Programming
A. Programming a Transaction Dump Code
1.
2.
3.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
For a CODE DUMP, press:
50 # 2 # user location # code * code *
For a CARD DUMP, press:
50 # 2 # user location # ** <present card>
and then present the card at the proximity reader.
Press * to exit program mode.
NOTE: Entering the programmed dump code or card
again subsequently causes the unit to print a Transaction Log to the optional IR printer.
B. Printing a Transaction Log Manually
1.
2.
3.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Hold the optional IR printer up to the EntryProx
IR port steadily (about one or two inches away;
the IR port is located to the right of the yellow
LED) and then press:
70 # 0 # 0 # **
Press * to exit program mode.
The 70 command is logged in the transaction buffer (in memory), providing a reference as to when
EntryProx Installation/Programming Manual
3-17
Chapter 3: Programming
3.13 Using the Printing Features
the log was printed. Figure 3-1 shows a sample
Transaction Log.
Figure 3-1 Transaction Log
The top line of the Transaction Log is the self-explanatory DATE. The second line contains the three column
headings, #, Time, and Action.
The first left-most column (#) is an event line number,
which increments from 1 to 0 (actually 10) and repeats.
The second column is the event TIME in 24-hour format.
The third column is the ACTION that describes a particular event, USER, REX, FORCED DOOR, etc. Page 3-15
contains a complete list of transaction events.
The column to the right of action is the EntryProx-generated, four-digit USER LOCATION. This is the location in
memory where the user data is stored.
The right-most column describes the type of EVENT,
Print, Access, LO ON, etc.
3-18
EntryProx Installation/Programming Manual
3.13 Using the Printing Features
3.13.3 Erasing a
Transaction Log
Chapter 3: Programming
The Transaction Log should be erased from memory
after being printed to prevent conflicting logs. To
erase the log, enter the following sequence:
99 # Master Code * 76 # 00000 # 00000 # **
Then press * to exit program mode.
3.13.4 Printing a
Programmed Users
List
The Programmed Users List showing all user access
information can be printed to an optional IR printer
via the unit’s IR port. The Print Programmed Users
List command is 25.
The EntryProx unit can store up to 2,000 user IDs in
memory at one time. Each user ID can be a card, a PIN
code, or a combination card/PIN code. User data is
stored in numbered registers, with register one being
known as “user one,” register two “user two,” etc. User
data is stored in the available memory registers automatically by the unit; you do not have to place data in
any particular order.
You can store codes or cards in the first five registers
and skip some registers, leaving them empty on purpose; you can then continue programming from registers that are out of sequence. This is an important
concept since the printed list identifies the memory
register (location) for each user ’s data. It does not print
user locations that are not programmed.
1.
2.
Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)]
A slow blinking yellow LED indicates that the unit
is in program mode. A steady yellow LED, in
contrast, means that errors were detected during
programming. Error states can be cleared by pressing the asterisk * key.
Hold the optional IR printer up to the EntryProx
IR port steadily (about one or two inches away;
EntryProx Installation/Programming Manual
3-19
Chapter 3: Programming
3.13 Using the Printing Features
3.
the IR port is located to the right of the yellow
LED) and then press:
25 # 0 # 0 # **
When the list is complete, press * to exit program
mode. Figure 3-2 shows a sample Programmed
Users List. To maintain a more detailed record,
simply write down each user ’s name beside the
corresponding line number.
Figure 3-2 Programmed User List
The top line of the Programmed User List is the DOOR
NUMBER on which the EntryProx unit is installed. The
second line is the TITLE of the list. The list proper is composed of four columns, oriented from left to right. The
first, left-most column is the four-digit USER NUMBER.
The second column is the two-digit USER TYPE. The
first letter denotes the access modes (S, B, E), the second letter the user type (T, N, D, L).
S = Single PIN
B = BOTH code and card
E = EITHER code OR card
T = Toggle function is allowed for this user
N = Normal user
D = Print dump feature is allowed for this user
L = Lockout feature is allowed for this user
The third column is the CODE NUMBER.
The right-most and fourth column is the combination
SITE CODE/CARD NUMBER. (The Site Code is not entered manually; it is embedded on the proximity card.
011 is the default for HID cards.)
3-20
EntryProx Installation/Programming Manual
3.14 Defaulting EntryProx Memory
Chapter 3: Programming
If necessary, the EntryProx main memory can be de3.14 Defaulting
EntryProx Memory faulted. This procedure explains how to do this; see
Figure 3-3 below. You would default the memory, if,
for instance, static discharges have corrupted the EntryProx unit, during shipping or installation. You can
also do this if you have simply forgotten the Master
Code and you need to enter program mode.
With the power ON, remove the case from the EntryProx front controller/keypad to access the main circuit board. (For a visual reference of the main printed
circuit board and the related pin connectors, see Figure
2-3. Table 2-1 describes these pins in detail.) (When
handling the main printed circuit board, to guard
against possible static discharges, touch a grounded
object BEFORE touching the EntryProx unit.)
FORGET MASTER CODE
PCB
MASTER
CODE
SWITCH
(PROGRAM
SWITCH)
(ON REAR SIDE
OF PC BOARD)
CONTROLLER
HOUSING
Figure 3-3 Program Button Location on Main
Circuit Board
EntryProx Installation/Programming Manual
3-21
Chapter 3: Programming
3.14 Defaulting EntryProx Memory
2.
With the power ON, press and hold the Program
button (located on the rear side of the main printed
circuit board) for two seconds.
The yellow LED flashes slowly.
3. Enter the following on the keypad:
46 # 00000 # 00000 # **
The yellow LED flickers for 10 seconds and then
blinks slowly.
4. Once the memory set-up is complete, re-assemble
the unit.
NOTE: CONNECTING DOOR LOOP INPUTBefore powering up the EntryProx unit, connect the Door Loops input to the “Loop Common.”
This prevents “Forced Door” or “Propped Door”
conditions from developing upon power-up.
3-22
EntryProx Installation/Programming Manual
3.15 Programming Codes
Chapter 3: Programming
3.15 Programming If you need to change any of the program default
values or wish to add functions, first enter program
Codes
mode and then enter the desired program code. Defaults are in bold.
Table 3-4. Program Codes
Action Desired
Press
Details
To enter program
mode
99 # (Master Code)
yellow LED blinks
slowly
1. Change master
code
Code-only
operation
(example, 4321
master code)
2. Set main relay
time
1 # (new code) * (repeat code) *
1 # 4321 * 4321 *
11 # tt # 0 # **
tt=1-99 seconds
3. Set AUX relay
output
15 # output # 0 # **
0=disabled,
1=shunt,
2=forced door,
3=propped door
4. Delete users
user-location # **
see section 3.12
5. Print a
transaction log
70 # 0 # 0 # **
6. Set/clear
standard option
30 # option # s/c # **
Option
0, audio keypress feature
1, visual keypress feature
2, auto entry enable
3, standalone/wiegand
operation
4, facility code access
5, forced door audio alert
6, propped door audio alert
EntryProx Installation/Programming Manual
see below
Set/Clear
0=OFF, 1=ON
0=OFF, 1=ON
0=OFF, 1-ON
0=standalone
1=wiegand
0=OFF, 1=ON
0=OFF, 1=ON
0=OFF, 1=ON
3-23
Chapter 3: Programming
3.15 Programming Codes
Table 3-4. Program Codes (continued)
Action Desired
Press
Details
Option
7, internal rex switch
8, US/EU date format
9, wiegand red LED enable
10, wiegand red led active
state
11, wiegand green led
enable
12, wiegand green led
active
13, daylight savings time
7a. Print
programmed user list
25 # 0 # 0 # **
7b. Print
programmed user
list (starting at a
certain user)
25 # 0 # start user # **
8. Change Wiegand
parameters
32 # parameter # value # **
Set/Clear
0=OFF, 1=ON
0=US,
1=European
0=OFF, 1=ON
0=LOW,
1=HIGH
0=OFF, 1=ON
0=LOW,
1=HIGH
0=OFF, 1=ON
see section 3.13.4
Parameter
0, wiegand pulse count
1, wiegand interpulse
2, facility code
see below
Value
1-255
(8-160µs)
1-255
(spacing
32-640µs)
0-255
(defaults to 0)
9. Set system time
41 # hhmm # 0 # **
hhmm=hour/minute,
24-hr format
10. Set system date
42 # mmddyy # dow # **
mmddyy=month,
date, year; dow=day
of week, 1=Sunday
11. Set door number
43 # nnnn # 0 # **
nnnn=door number
3-24
EntryProx Installation/Programming Manual
3.15 Programming Codes
Chapter 3: Programming
Table 3-4. Program Codes (continued)
Action Desired
Press
Details
44 # ttt # 0 # **
ttt=propped door
time, to nearest 10’s
seconds, entered as
10-990; default=30
secs
13. Set forced door
time (this sets time
for both Aux Relay
and local sounder
45 # ttt # 0 # **
ttt=propped door
time, to nearest 10’s
seconds, entered as
10-990;
default=10 secs
14. Delete memory
except user list
and restore system
defaults (also see
command 46)
40 # 00000 # 00000 # **
see section 3.3
15. Delete all
memory and reset
system defaults
46 # 00000 # 00000 # **
see section 3.4
16. Program user:
Code ONLY
50 # user-type # user location # code *
repeat code *
NOTE: You can program the four types of
users shown to the right (refers to items
16-19).
17a. Program user:
Code AND Card
50 # user-type # user location # code *
repeat code * <present card>
17b. Program user:
Card ONLY
50 # user-type # user location # **
<present card>
12. Set propped
door time (this sets
time for both Aux
Relay and local
sounder
18. Program user
manually: Card
ONLY (26-bit cards
ONLY)
51 # user-type # user location #
card PIN * card PIN *
EntryProx Installation/Programming Manual
0-Toggle/latch strike,
1-Normal access,
2-log Dump, and
3-Lockout.
the card PIN
appears on the card
(facility code must
be entered first; see
32 # 2 # command)
3-25
Chapter 3: Programming
3.15 Programming Codes
Table 3-4. Program Codes (continued)
Details
Action Desired
Press
19. Program user:
Code OR Card
52 # user-type # user location # code *
repeat code * <present card>
20. Perform batch
entry of users
(26-bit cards ONLY)
53 # total count # start card # card PIN *
the card PIN
appears on the
card; see section 3.8
21. Print Transaction
Log via IR port
70 # 0 # 0 **
see section 3.13.2
73 # event # set/clear # **
see section 3.13.1;
see below
22. Set transaction
log mask (set/clear
event logging)
Code
01
02
03
04
05
06
07
08
09
16
17
20
21
24
25
27
23. Reset/erase
transaction log
3-26
Transaction Event
Access Denied
Program Denied
Program Mode
REX (Request to Exit)
Door Ajar
Door Closed
Forced Door
Log Erased
Facility Access
Print
Access
TGL ON (Toggle ON)
TGL OFF
Lo ON (Lockout ON)
Lo OFF
MSMTCH (Mismatch)
76 # 00000 # 00000 # **
see section 3.13.3
EntryProx Installation/Programming Manual
Chapter 4:
Troubleshooting
Chapter 4 furnishes a Troubleshooting Chart, diagnostic flow charts, a power supply integrity test, and information to correct possible water problems.
4.1 Before Calling
HID
Whenever your EntryProx unit experiences difficulty,
before calling HID for help, first refer to the Troubleshooting Chart for answers. If the Troubleshooting
Chart does not help, perform the following:
1.
2.
3.
4.
5.
6.
Write down the time and date that the problem
occurred, or the time and date when you first
noticed the problem. Also note what the unit was
doing when the problem occurred or was first
noticed.
Note all other relevant information, paying particular attention to recent updates, new or inexperienced installers/programmers, or any recent
hardware changes to the optional IR printer or
separate Wiegand panel or central access control
panel.
Attempt to isolate the problem.
Refer to the “Troubleshooting Chart” and flow
charts in this chapter. They are designed such that
many common problems can be easily diagnosed
and corrected by users without HID assistance.
Contact your supervisor or the “technical subject
expert” at your facility for assistance for help if
you cannot diagnose and correct the problem
yourself using steps 1-4 above
Contact HID for help only if using steps 1-5 above
fails to resolve the problem. Make sure that you
EntryProx Installation/Programming Manual
4-1
Chapter 4: Troubleshooting
4.1 Before Calling HID
have a written description of the problem (and
any steps you may have taken attempting to remedy the problem) before calling for help. Write
down the version number of your EntryProx unit
before calling HID for help.
Table 4-1. Troubleshooting Chart
Problem
Probable Cause
Solution
Red LED turns
green when access
accepted, but door
does not open
Various: power
supply voltage
problems, locking
device power supply
not set correctly
1. Check power supply voltage.
2. Monitor voltage at unit’s V+ and
V- terminals (on P1) with meter,
enter a valid code, and ensure
that voltage remains constant
while locking device attempts to
unlock and relock. If voltage
varies 1/4 volt or more during this
test, this is a problem you must
correct; look for the following:
-verify that power supply is rated
sufficiently for all equipment being
powered
-verify that locking device, if on
same power supply, is set up for
current being drawn (example: if a
lock draws 300mA at 24VDC,
same lock may draw 600mA at
12VDC, especially if the unit
requires that jumpers be placed in
a different configuration
-place meter across lock power
wires at lock and ensure the lock
is receiving proper voltage
EntryProx unit
experiences reduced
read range problems
Various: unit is
mounted on a metal
surface, or other
equipment producing
RF interference
For metal surface problems, see
section 2.2.3; for RF interference
problems, see section 2.2.4.
4-2
EntryProx Installation/Programming Manual
4.1 Before Calling HID
Chapter 4: Troubleshooting
Table 4-1. Troubleshooting Chart (continued)
Problem
Probable Cause
Solution
EntryProx unit not
entering program
mode when 99 #
Master code * is
pressed on the
EntryProx keypad or
installer/programmer
forgets the “master
code"
Various: master code
has been changed,
is incorrect, or new
code not
programmed correctly
1. With power to the EntryProx
unit turned ON, remove the main
circuit board from the unit as
described in section 2.5.6.
2. Locate the “Program” button
(SW1) underneath the main
circuit board and press it for
about 2 seconds. Take care if you
must pull the circuit board out of
the plastic housing. Handle the
board by its edges, otherwise,
your fingers can short the solder
points. Figure 3-2 illustrates the
location of this button. (When
handling the main printed
circuit board, to guard against
possible static discharges,
touch a grounded object
BEFORE touching the
EntryProx unit.) (The yellow LED
blinks slowly, indicating that
program mode is active.)
3. To program a new master code,
press:
1# new-code * repeat-code *
The code can be 1-6 digits, with
repeated numbers acceptable.
4. To exit program mode, press * .
5. Continue programming as
described in Chapter 3.
EntryProx Installation/Programming Manual
4-3
Chapter 4: Troubleshooting
4.2 Flow Charts
4.2 Flow Charts
EntryProx Indicates "Acceptance," But No
Main Relay Action Occurs
1. Meter and verify correct keypad voltage. 2. Reference
EntryProx instructions.
NO
YES
Perform power
integrity test
(section 4.3).
PASS
1. Resolve issue, then erase
EntryProx memory to elminate
problem. 2. Enter default code,
1234* .
FAIL
FAIL
PASS
1. Set meter to read continuity,
remove power from Main relay
common of EntryProx. 2. Enter
code 1234* to verify that relay
activates.
Persistent?
Revert to above
step.
1. Reprogram EntryProx
and re-test. 2. See "Note" at
bottom of page.
Troubleshoot per
instructions in Table 4-1.
PASS
FAIL
Bad EntryProx
The EntryProx is working
properly, the problem may
reside with the locking device.
Meter voltage at lock and
enter 1234* .
Meter show
change?
NO
Change not occurring
YES
Power is getting to lock
Ring out wires between
EntryProx and lock.
Bad lock
NOTE: A glitch in the EntryProx program might result from using a
power supply that is not filtered and regulated properly. For extra
filtering suggestions, call HID technical support.
4-4
EntryProx Installation/Programming Manual
4.2 Flow Charts
Chapter 4: Troubleshooting
Programmed Codes Stop Working;
Keypad Buttons Not Working
1. Meter and verify correct keypad voltage. 2. Verify keypad power
selection jumper is selecting the same voltage provided by the
power supply. 3. Reference keypad instructions. 4. Verify that kick
back protection installed to specifications.
YES
NO
Confirm that each keypad button is not damaged by
using the Keypress Feedback feature. (A damaged
button will cause a digit to be read more than once
or not at all, resulting in denied access.)
1. Resolve issue. 2. Erase keypad memory to
erase any program glitch. 3. Enter default
code, 1234* .
PASS
FAIL
FAIL
PASS
Verify that the asterisk button (*) is being
used like the <Enter> key. (This may be
turned ON/OFF in programming.)
1. Reprogram keypad
and re-test. 2. See "Note"
at bottom of page.
1. Erase entire keypad memory to erase any
program glitch. 2. Enter default code, 1234* .
PASS
1. Reprogram keypad
and re-test. 2. See "Note"
at bottom of page.
Perform power
integrity test
(section 4.3).
FAIL
PASS
If using mullion style keypad, verify that
mounting hardware and cables are
installed per specifications. Xtremepad,
check cable specifications.
1. Set meter to read continuity. 2.
Remove power from common terminal
of keypad. 3. Enter 1234* to verify that
relay activates.
Troubleshoot per instructions
in Chapter 4 in this manual).
FAIL
Bad
keypad
PASS
Device used to prevent electric kick
back conflicts with existing device built
into lock. Remove and test.
NOTE: A glitch in the keypad program might result from using a power
supply that is not filtered and regulated properly. For extra filtering
suggestions, call HID technical support.
EntryProx Installation/Programming Manual
4-5
Chapter 4: Troubleshooting
4.2 Flow Charts
External Request to Exit Input Not
Activating EntryProx
1. Meter and verify correct EntryProx voltage. 2. Reference
EntryProx instructions.
YES
NO
Perform power integrity test
(section 4.3).
1. Resolve issue. 2. Erase EntryProx memory
to erase any program glitch.
PASS
FAIL
Troubleshoot per instructions
in Table 4-1.
1. Verify that door position switch closed before
attempting to engage the REX. (EntryProx ignores
this input when door is open.) 2. If no door
contacts are used, jumper input together with a
piece of wire and try again.
1. Disconnect any devices connected to white,
orange, and brown. 2. Short the W and
O wires together and maintain connection. 3.
Momentarily short the O and B/R terminals to
activate the egress input. Does the EntryProx
work?
PASS
Solved! Shut the
door.
FAIL
YES
NO
Bad
EntryProx
PASS
1. With the door contacts closed, meter continuity
between exit switch and wires from EntryProx.
(Meter should read an open and then a closed
circuit when exit device is activated.) 2. Reconnect
exit switch. 3. With door contact input closed, try
the switch again.
FAIL
1. Verify that no other equipment is monitoring
same door contacts as EntryProx. 2. If so,
disconnect all other devices on that set of
contacts, except the EntryProx. 3. Try again.
1. Verify that exit device is "dry contact"
and no induced voltages, A/C or D/C, are
being applied to input. 2. More than one
volt?
YES
If problem persists,
see Note at bottom.
NO
Locate source and
eliminate. (Circuit requires
a dry switch.)
NOTE: A glitch in the EntryProx program might result from using a
power supply that is not filtered and regulated properly. For extra
filtering suggestions, call HID technical support.
4-6
EntryProx Installation/Programming Manual
4.3 Performing Power Supply Integrity Test
4.3 Performing
Power Supply
Integrity Test
Chapter 4: Troubleshooting
This test confirms whether or not the power source is
providing sufficient amperage to support all the equipment. It indicates whether or not a stable electrical
environment exists by revealing fluctuating voltages
during operations. A fluctuation in voltage exists when
the equipment draws more amperage than the power
supply offers.
As the EntryProx unit cycles the equipment ON and
OFF, power must remain constant. If a voltage fluctuation of one-quarter volt or more occurs during testing,
in either the positive or negative direction, the test
results indicates a “fail” response. If the voltage retains
proper amplitude (remains constant), the test indicates
a “pass” response.
1.
2.
3.
Set the meter to read voltage and place meter
probes on the red and black wires of P1, located
on the EntryProx unit. You may have to reference
Figure 2-3 for details. If the EntryProx unit consists
of two parts, a reader and a controller, the terminals are located on the controller.
The voltage reading is monitored throughout the
entire test.
With power being applied to the entire EntryProx
unit, enter a valid code on the EntryProx keypad.
The REX input can be used in place of a valid
code; the test results remain the same. Reference
the keypad circuits diagram for REX input, located
in Chapter 2 of this manual.
Observe the meter as the keypad cycles the system
ON and OFF. The voltage should remain constant
during this operation, indicating that the electrical
system is stable and adequate.
EntryProx Installation/Programming Manual
4-7
Chapter 4: Troubleshooting
4.
4-8
4.3 Performing Power Supply Integrity Test
Constant voltage during the test indicates a
“PASS” response. If the voltage changes more than
one-quarter of a volt (.25), the test indicates a
“FAIL” response.
If the test indicates a “FAIL” response, refer to the
“Power Supply Integrity Test Indicating Fluctuating Voltage” flow chart on the next page to troubleshoot the unit. If the test indicates a “PASS”
response, return to the “External Request to Exit
Input Not Activating EntryProx” flow chart and
resume your work.
EntryProx Installation/Programming Manual
4.3 Performing Power Supply Integrity Test
Chapter 4: Troubleshooting
Power Supply Integrity Test Indicating Fluctuating Voltage
Fluctuating voltage encountered while performing the test in section 4.3 is the result of
defect in the electrical system. This flow chart pertains to units consisting of one power
supply providing for one EntryProx, one electric lock, and any accessories (for example,
motion egress detector).
YES
Meter and verify that voltage from electrical outlet
is in tolerance.
NO
Check circuit breaker, or obtain assistance of a
licensed electrician.
1. Acquire an alternative power supply that matches
unit voltage, battery preferred. 2. Disconnect
EntryProx power by removing wires from the (+) and
(-) wires at EntryProx. 3. Connect alternative power
to EntryProx and re-test per section 4.2.
FAIL
Resolve and re-test per instructions in
section 4.3.
PASS
FAIL
Ensure power supply donates ample power by
adding the max. current draw of each device.
(Total AMPs should be less than provided by
power supply.)
1. Disconnect all accessories and lock from
EntryProx. 2. Re-connect original power
supply. 3. Re-test per instructions in section
4.3.
PASS
A larger power
supply is required.
PASS
FAIL
Bad
EntryProx
If applicable, ensure the lock's power selection
jumper is selecting proper voltage setting. (In
wrong position, current draw doubles.)
Problem is prior to
the EntryProx.
The following are possible causes for negative
test results. To resolve, try and isolate each
device by swapping or removing from the circuit
one part at a time.
-Defective power supply not producing rated amount.
-Defective power supply no longer producing rated amount.
-Defective battery loading down the unit.
-Nick or crack in conductor acting like an in-line resistor.
-Return to step 3 in section 4.3 and continue.
NOTE: A glitch in the EntryProx program might result from using a power
supply that is not filtered and regulated properly. For extra filtering
suggestions, call HID technical support.
EntryProx Installation/Programming Manual
4-9
Chapter 4: Troubleshooting
4.4 Correcting
Possible Water
Problems
4.4 Correcting Possible Water Problems
Approximately 3% of all returns (RMAs) are caused by
water damage. EntryProx units that are mounted outdoors require certain preventive steps to avoid being
damaged by water. This section discusses the reasons
water can accumulate in keypads and the steps to
prevent this.
A. Silicone
1.
2.
Use silicone to seal wire runs and mounting holes.
Do NOT seal the cover and base together.
Keypads are designed to direct any water that
enters the two constituent pieces, base and cover,
towards the bottom and out a drain or weep hole.
B. Wire Run
Bend the wires before they enter the case to form a
drip loop. Often water follows the wires to the connection point of the circuit board and shorts out the
terminals to which the wires are connected.
4-10
EntryProx Installation/Programming Manual
Chapter 5:
Miscellaneous
Information
Chapter 5 contains miscellaneous information, such as
HID’s customer service policy, returned merchandise
authorization policy, and consumables information.
5.1 Customer
Service Policy
HID has a Customer Service department to meet the
varied service needs of its customers. Examples of department functions include:
•
•
Telephone troubleshooting with technical experts
Technical assistance to solve specific application
questions is handled by the Sales department
HID’s Customer Service department can help customers expedite shipments, contact the proper personnel,
or help with special customer requests. To contact
HID’s Customer Service department, call (800) 237PROX. A Customer Service Representative is available
from 8:00 a.m. to 7:00 p.m. (Pacific Coast Time) to:
•
•
•
•
check on installation
request technical assistance
report a problem
return products
EntryProx Installation/Programming Manual
5-1
Chapter 5: Miscellaneous Information
5.2 RMA Policy
“RMA” stands for Returned Merchandise Authorization.
1.
2.
3.
4.
5.
5-2
5.2 RMA Policy
A warranty claim must be made promptly and
must be received during the applicable warranty
period by HID or your authorized HID distributor.
If it becomes necessary to return a product for
repair and/or adjustment, prior authorization
from HID or your HID-authorized distributor
must be obtained. Instructions as to how and
where these products should be shipped will be
provided by HID or your HID-authorized distributor.
Any product or component returned for examination and/or warranty repair shall be sent to HID
in Irvine, California, or any of their authorized
representatives. All items must be returned at the
customer ’s cost (freight prepaid), quoting a return
authorization number which is available from the
Service department. All products or components
repaired or replaced under warranty will be returned to the customer at HID’s cost using UPS
(United Parcel Service) or an equivalent service.
In all cases, HID or your HID-authorized distributor has sole responsibility for determining the
cause and nature of failure, and HID’s or the distributor ’s determination with regard thereto shall
be final.
All parts that are replaced under warranty will
become the property of HID.
EntryProx Installation/Programming Manual
Appendix A: Users
Chart
User
Type Code
Location
Card
AND
EntryProx Installation/Programming Manual
OR
Last
Name
First
Name
Other
A-1
Index
A
About this Manual, ix
Adding Cards via Batch Entry, 3-8
Adding New or Changing Existing
Codes/Cards, 3-7
Alarm Output Selection, 1-3
B
E
EntryProx Default Settings, 3-2
EntryProx LED Indicators/Sounder
Operation, 3-3
EntryProx Operation, 1-4 - 1-6
EntryProx User Types, 3-13
Erasing a Transaction Log, 3-19
Erasing Entire Memory/Resetting
System Defaults, 3-5
Batch Entry, 3-8
Before Calling HID, 4-1 - 4-3
C
Card Presentations, 3-7
Changing the Main Relay Time, 3-4
Checking the Cables, 2-6 - 2-9
Code/Card Users, 3-9
Correcting Possible Water Problems,
4-10
Customer Service Policy, 5-1
D
Defaulting EntryProx Memory, 3-21 3-22
Deleting Users, 3-14
Design Change Disclaimer, ix
Design Function, 1-1
F
FCC Warning, xii
Filler operation, 2-17
Filler or REX operation, 2-17
Flow Charts, 4-4 - 4-6
FOREWORD, Chapter
about this manual, ix
design change disclaimer, ix
fcc warning, xii
items supplied from the factory, xi
items the installer must supply, xi
reproduction disclaimer, ix
safety warnings and cautions, ix
technical support, ix
warranty, x
EntryProx Installation/Programming Manual
I-1
Index
G
Gang Box and Mounting, 2-2
General Description, 1-1
Glass Mounted Installation, 2-1
Grounding the Power Supply, 2-2
I
Inputs/Outputs, 1-2
INSTALLATION, Chapter 2
checking the cables, 2-6 - 2-9
gang box and mounting, 2-2
grounding the power supply, 2-2
installation configurations, 2-1
mounting the entryprox unit, 2-10 2-17
mounting the unit on metal, 2-3
other installation considerations,
2-2 - 2-5
performing a glass mounted
installation, 2-12
performing a secure installation,
2-14
performing a wall mounted
installation, 2-10
power supply/current requirements, 2-2
removing/inserting circuit boards,
2-30
rf interference, 2-3
testing the controller/keypad, 2-31
testing the entryprox unit, 2-31
wiegand operation, 2-4
wiring aux relay for use as alarm
shunt, 2-18
wiring the aux relay for use as
I-2
forced door, 2-20
wiring the aux relay for use as
propped door, 2-22
wiring the door contact input, 2-24
wiring the main relay, 2-28
wiring the entryprox unit, 2-18 2-30
wiring the rex switch, 2-26
Installation Configurations, 2-1
INTRODUCTION, Chapter 1
alarm output selection, 1-3
design function, 1-1
general description, 1-1
inputs/outputs, 1-2
operating modes, 1-3
EntryProx operation, 1-4 - 1-6
unit capacity, 1-2
uses and installation
configurations, 1-2
Items Supplied from the Factory, xi
Items the Installer Must Supply, xi
K
Keypress Sequences, 3-7
M
Masking, 3-15
Master Code, 3-1
MISCELLANEOUS INFORMATION,
Chapter 5
customer service policy, 5-1
rma policy, 5-2
Mounting the EntryProx Unit, 2-10 -
EntryProx Installation/Programming Manual
Index
2-17
Mounting the Unit on Metal, 2-3
O
Operating Modes, 1-3
Other Installation Considerations,
2-2 - 2-5
P
Performing a Glass Mounted
Installation, 2-12
Performing a Secure Installation, 2-14
Performing a Wall Mounted
Installation, 2-10
Performing Power Supply Integrity
Test, 4-7 - 4-9
Power Supply/Current Requirements,
2-2
Printing a Programmed Users List,
3-19
Printing a Transaction Log, 3-16
Printing a Transaction Log Manually,
3-17
Programmed Users Log, 3-14
PROGRAMMING, Chapter 3
adding cards via batch entry, 3-8
adding new or changing existing
codes/cards, 3-7
changing the main relay time, 3-4
code/card users, 3-9
defaulting entryprox memory,
3-21 - 3-22
deleting users, 3-14
entryprox default settings, 3-2
EntryProx Installation/Programming Manual
entryprox led indicators/sounder
operation, 3-3
entryprox user types, 3-13
erasing a transaction log, 3-19
erasing entire memory/resetting
system defaults, 3-5
master code, 3-1
printing a programmed users list,
3-19
printing a transaction log, 3-16
printing a transaction log manually,
3-17
programming a toggle user, 3-12
programming a transaction dump
code, 3-17
programming card only use, 3-11
programming code and card use,
3-11
programming code only use, 3-10
programming code or card, 3-11
programming codes, 3-23 - 3-26
programming for both code and
card, 3-9 - 3-11
programming from the keypad, 3-1
- 3-3
programming user data, command
50, full format, 3-10
programming user types, 3-13
quick program feature, 3-10
resetting the master code and system
defaults only, 3-4
selecting transaction log information,
3-15
turning audio keypress feedback
on/off, 3-5
turning visual led/keypress indicator
on/off, 3-6
I-3
Index
using the printing features, 3-15 3-20
Programming a Toggle User, 3-12
Programming a Transaction Dump
Code, 3-17
Programming Card ONLY Use, 3-11
Programming Code AND Card Use,
3-11
Programming Code ONLY Use, 3-10
Programming Code OR Card, 3-11
Programming Codes, 3-23 - 3-26
Programming for BOTH Code and
Card, 3-9 - 3-11
Programming from the Keypad, 3-1 3-3
Programming User Data, Command
50, Full Format, 3-10
Programming User Types, 3-13
Q
Quick Program Feature, 3-10
R
Removing/Inserting Circuit Boards,
2-30
Reproduction Disclaimer, ix
Request to Exit, 1-2
Request to Exit (REX) operation, 2-16
Request to Exit (REX) switch, 2-26
Resetting the Master Code and
System Defaults Only, 3-4
REX Button, 2-16
REX Feature, 2-26
I-4
REX Input, 4-7
REX Operation, 2-17
RF Interference, 2-3
RMA Policy, 5-2
S
Safety Warnings and Cautions, ix
Secure Installation, 2-1
Selecting Transaction Log
Information, 3-15
Silicone, 4-10
Standalone Mode, 1-3
T
Technical Support, ix
Testing the Controller/Keypad, 2-31
Testing the EntryProx, 2-31
Transaction Log, 3-12
TROUBLESHOOTING, Chapter 4
before calling hid, 4-1 - 4-3
correcting possible water problems,
4-10
flow charts, 4-4 - 4-6
performing power supply integrity
test, 4-7 - 4-9
silicone, 4-10
troubleshooting chart, 4-2
wire run, 4-10
Troubleshooting Chart, 4-2
Turning Audio Keypress Feedback
ON/OFF, 3-5
Turning Visual LED/Keypress
Indicator ON/OFF, 3-6
Types of Users, 1-1
EntryProx Installation/Programming Manual
Index
U
Unit Capacity, 1-2
Users Chart, A-1
Uses and Installation Configurations,
1-2
Using the Printing Features, 3-15 3-20
W
Wall Mounted Installation, 2-1
Warranty, x
Wiegand Mode, 1-3
Wiegand Operation, 2-4
Wire Run, 4-10
Wiring AUX Relay for Use as Alarm
Shunt, 2-18
Wiring the AUX Relay for Use as
Forced Door, 2-20
Wiring the AUX Relay for Use as
Propped Door, 2-22
Wiring the Door Contact Input, 2-24
Wiring the Main Relay, 2-28
Wiring the EntryProx Unit, 2-18 - 2-30
Wiring the REX Switch, 2-26
EntryProx Installation/Programming Manual
I-5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising