20 Series Data sheet UK
Automatic Liquid Dispenser
The Automatic Liquid Dispenser incorporates a pump and a flow-meter to deliver a measured volume
of liquid. Delivery can be initiated at the press of a button, by external input signal, or automatically
by means of an internal timer. The timer can be selected to start dispensing at regular intervals or
start dispensing at set times of the day, on a daily or a weekly basis.
The volume is easy to select and is retained in non-volatile memory for repeat operation. Volumes
between 0.20 litres and 100.00 litres can be selected in increments of 0.01 litres.
The Dispenser will accurately measure volumes over a flow rate range of between 0.05 litres/minute
and 5 litres/minute. A simple calibration method enables the dispenser to repeatedly deliver accurately
measured volumes and also allows for fine adjustment of the delivered volume.
The Automatic Liquid Dispenser has two John Guest Speedfit® push-fit connectors for fluid in and
out. The fittings take a tube with an outside diameter of 8mm and can be used with polyethylene,
nylon, polyurethane, brass, copper, or mild steel tubing. (Tube inserts should be used for soft or thinwalled tubing).
The front-panel display shows the selected volume and progress during dispensing. It also enables
various option menus to be viewed and provides warning messages if error conditions are detected.
The Dispenser has a serial communication option to enable automated control and monitoring by
computer, this requires a USB A to B cable.
The 12VDC mains adapter supplied with the dispenser plugs into the socket labelled on the rear panel.
Low voltage operation makes the dispenser safe to use in damp environments or where liquid can be
spilt.
Poppenbouwing 54, 4191 NZ Geldermalsen,
T:0345 596 000, info@adinco.nl, www.adinco.nl
The Deeter Group follows a policy of continual development of its products and reserves the right to
change specifications and/or features without notice.
www.deeter.co.uk
Automatic Liquid Dispenser
Specification
265mm x 120mm x 295mm
(wxhxd, excludes plumbing
and wiring connections)
Power supply
10-15VDC @ 3A
(12VDC mains
socket adapter
supplied)
Fuse
4A, anti-surge, 5x20mm
cartridge
Fluid Connections(1)
8mm OD, John
Guest Speedfit®
Serial
Communications
connector
USB Type B socket
Remote Switch
connector
Locking 3-pin DIN
plug (mating
socket supplied)
Dispensed Volume
Range
0.20 – 100 litres in 0.01 litre
steps
Nominal flow rate(2)
3.2 litres per
minute
Flow rate range(3)
.05 – 5.0 litres per minute
Dispense
Accuracy(4)
±1%
Fluid Temperature
Range
0°C to +43°C
Filter
Stainless Steel, 60
Mesh (250
microns)
Wetted Materials
acetal (polyformaldehyde)
polyether polyurethane
glass-filled polypropylene
glass-filled polyamide (Nylon)
polyamide-12 (Nylon-12)
nitrile rubber (NBR)
EPDM rubber
stainless steel
Pump Sound Level
65 decibels
(typical)
Dimensions
(1) Suitable tube materials include: polyethylene, nylon, polyurethane, brass, copper, mild steel. For
soft or thin-walled tubing, tube inserts should be used.
(2) Typical flow rate with 12V supply, clear filter, minimal external tube restrictions and minimal
height differential between outlet of fluid and pump.
(3) For accurate dispenses
(4) Water at constant temperature and flow rate
Ordering Information
Description
Ordering Code
Automatic Liquid Dispenser
DE012-0234
All electrical equipment should be installed by a qualified/certified electrician.
Poppenbouwing 54, 4191 NZ Geldermalsen,
T:0345 596 000, info@adinco.nl, www.adinco.nl
The Deeter Group follows a policy of continual development of its products and reserves the right to
change specifications and/or features without notice.
www.deeter.co.uk
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising